Specifications:
- SoC: Broadcom BCM6358 dual 300MHz MIPS
- Flash: 16MB NOR
- RAM: 64MB DDR
- Ethernet: 4x 100M
- Wifi: Broadcom BCM4318
- 2x USB 2.0 port
- 2x Button
- 9x LED
- RJ11 2x FXS VoIP (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
- Assign static IP 192.168.1.100 to PC.
- Unplug the power source.
- Press the RESTART button at the router, don't release it yet!
- Plug the power source and wait at least 15 seconds.
- Release the RESTART button.
- Browse to http://192.168.1.1 with your PC.
- Upload the openwrt-bmips-bcm6358-huawei_hg553-squashfs-cfe.bin file.
- Wait some minutes until the firmware upgrade completes.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
I-O DATA WN-DAX3000GR is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based
on IPQ5018.
Specification:
- SoC : Qualcomm IPQ5018
- RAM : DDR3 512 MiB
- Flash : SPI-NAND 128 MiB (Macronix MX35UF1G24AD-Z4I)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm IPQ5018 (SoC)
- 5 GHz : Qualcomm Atheros QCN6102
- Ethernet : 5x 10/100/1000 Mbps
- wan (phy) : Qualcomm IPQ5018 (SoC)
- lan (switch) : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO): 7x/5x
- UART : through-hole on PCB (J3)
- assignment : 3.3V, TX, RX, NC, GND from tri-angle marking
- settings : 115200n8
- USB : USB 2.0 Type-A (through-hole on PCB, "J6")
- Power : 12 VDC, 1A (Typ. 930 mA)
Flash instruction using factory.bin image:
1. Boot WN-DAX3000GR with router mode
2. Access to the WebUI ("http://192.168.0.1/") on the device and open
the firmware update page ("ファームウェア")
3. Select the OpenWrt factory.bin image and click update ("更新") button
4. Wait ~120 seconds to complete flashing
Switching to the stock firmware:
1. Load the elecom.sh script
. /lib/upgrade/elecom.sh
2. Check the current index of rootfs
bootconfig_rw_index 0:bootconfig rootfs
3. Set the index to inverted value
bootconfig_rw_index 0:bootconfig rootfs <value>
bootconfig_rw_index 0:bootconfig1 rootfs <value>
example:
- step2 returned "0":
bootconfig_rw_index 0:bootconfig rootfs 1
bootconfig_rw_index 0:bootconfig1 rootfs 1
- step2 returned "1":
bootconfig_rw_index 0:bootconfig rootfs 0
bootconfig_rw_index 0:bootconfig1 rootfs 0
4. Reboot
Partition Layout (Stock FW, bootconfig(rootfs)=1):
0x000000000000-0x000000080000 : "0:SBL1"
0x000000080000-0x000000100000 : "0:MIBIB"
0x000000100000-0x000000140000 : "0:BOOTCONFIG"
0x000000140000-0x000000180000 : "0:BOOTCONFIG1"
0x000000180000-0x000000280000 : "0:QSEE"
0x000000280000-0x000000380000 : "0:QSEE_1"
0x000000380000-0x0000003c0000 : "0:DEVCFG"
0x0000003c0000-0x000000400000 : "0:DEVCFG_1"
0x000000400000-0x000000440000 : "0:CDT"
0x000000440000-0x000000480000 : "0:CDT_1"
0x000000480000-0x000000500000 : "0:APPSBLENV"
0x000000500000-0x000000640000 : "0:APPSBL"
0x000000640000-0x000000780000 : "0:APPSBL_1"
0x000000780000-0x000000880000 : "0:ART"
0x000000880000-0x000000900000 : "0:TRAINING"
0x000000900000-0x000003c40000 : "rootfs_1"
0x000003c40000-0x000003fc0000 : "Config"
0x000003fc0000-0x000007300000 : "rootfs"
0x000007300000-0x000007680000 : "Config_2"
0x000007680000-0x000007700000 : "idmkey"
0x000007700000-0x000007c00000 : "Reserved"
0x000007c00000-0x000007c80000 : "FWHEADER"
0x000007c80000-0x000007d00000 : "Factory"
Known Issues:
- This device has a Macronix MX35UF1G24AD SPI-NAND chip registered as
oobsize=128 in Linux Kernel. But using BCH8 breaks I/O on the chip
with the following errors, so this support uses BCH4 instead.
[ 1.542261] 0x000000480000-0x000000500000 : "0:appsblenv"
[ 1.547959] 1 fixed-partitions partitions found on MTD device 0:appsblenv
[ 1.551265] Creating 1 MTD partitions on "0:appsblenv":
[ 1.558096] 0x000000000000-0x000000040000 : "env-data"
[ 1.627282] u-boot-env-layout 79b0000.qpic-nand:flash@0:partitions:partition-0-appsblenv:partition@0:nvmem-layout: probe with driver u-boot-env-layout failed with error -74
root@OpenWrt:~# strings /dev/mtdblock10
[ 77.806720] mtdblock: MTD device '0:appsblenv' is NAND, please consider using UBI block devices instead.
[ 77.807554] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0
[ 77.815977] I/O error, dev mtdblock10, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0
[ 77.824721] I/O error, dev mtdblock10, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 0
[ 77.834095] I/O error, dev mtdblock10, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[ 77.843278] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 77.851577] Buffer I/O error on dev mtdblock10, logical block 0, async page read
Notes:
- This device has dual-boot feature and it's managed by the index in the
0:bootconfig and 0:bootconfig1 partitions.
- There are through-holes on PCB for USB 2.0, but it cannot be accessed
without disassembly of the housing. So it's not enabled in this
support.
- WN-DAX3000GR has the "bt_fw" volume in the firmware UBI in addition to
the volumes that will be removed in the section of ELECOM WRC-X3000GS2
in /lib/upgrade/platform.sh.
That volume is unnecessary for OpenWrt and add
`remove_oem_ubi_volume bt_fw` to remove that volume when sysupgrade.
(that function doesn't anything without errors if no specified volume)
MAC Addresses:
LAN : 50:41:B9:xx:xx:64 (0:APPSBLENV, "ethaddr"/"eth1addr" (text))
WAN : 50:41:B9:xx:xx:66 (0:APPSBLENV, "eth0addr" (text))
2.4 GHz: 50:41:B9:xx:xx:64 (0:APPSBLENV, "wifi0" (text))
5 GHz : 50:41:B9:xx:xx:65 (0:APPSBLENV, "wifi1" (text))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19053
Signed-off-by: Robert Marko <robimarko@gmail.com>
I-O DATA WN-DAX3000GR has a MSTC (Mitra Star Technology Corp.) specific
header with a different length than ELECOM WRC-X3000GS2.
Make the header length configurable by parameterizing on
Build/mstc-header.
- WRC-X3000GS2: 0x400
- WN-DAX3000GR: 0x480
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19053
Signed-off-by: Robert Marko <robimarko@gmail.com>
The reason fwmode 2 was used for ipq5018 and qcn6122 wifi was that
coldboot calibration doesn't work and causes the firmware to crach
during wifi bringup. Since coldboot calibration is now disabled in the
driver, all boards can now use their respective firmware memory mode, so
let's the property in all board DTS files accordingly.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19083
Signed-off-by: Robert Marko <robimarko@gmail.com>
The I2C and SPI packages required for each RPi generation is different.
Therefore, in order to avoid confusion let's select them by default.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Three different code paths for the same phy model. Now the bus
is prepared to handle c45 (mmd) read/writes correctly. Remove
the custom implementations and let generic kernel functions do
their best. To achieve this
- disable the PHY-mode EEE in rtl821x_config_init() as upstream does
- provide mmd read/write functions that avoid EEE via c45 over c22
While chaning the phy_driver functions sort them alphabetically.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
rtl8214fc_media_is_fibre() will need to be run when bus lock is held.
Split the function into two versions.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
As the mdio bus has been hardened and can now handle c45 requests
the DSA driver must honor that as well. For this
- add proper upstreamed bus read_c45 and write_c45 functions
- take over the disabled port mask from upstream bus
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
With the follow up EEE patches the mdio bus will run c22 and c45
accesses during initial scan. Especially when accessing addresses
beyond the CPU port phy requests might fail in a way that cannot
be handled gratefully. Do two things
- do not allow access to addresses starting from cpu port
- set the scan disable bitmask to ports starting from cpu port
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some bits where missed during the last enhancement of the mdio
patch. In the forthcoming patches the phy_mask will be populated
to avoid unwanted ports (>= cpu port) from being scanned. Add
additional locations where 32 bit values need to be converted
to 64 bits.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
If mmd and normal phy ops are issued the bus is lost because
of wrong park page settings. Force it to 0x1f as in GPL.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Allow to build the new kernel.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
The new kernel has relocated the definition of struct platform_device.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
The DSA driver uses set_mac_eee() for the outside API while
the interal helper is called port_eee_set(). Align that.
Additionally do not call the internal helpers directly by
the function names but use the register assignments.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream will get rid of the get_mac_eee() function in the DSA
driver and replace it by a boolean alternative. While we fill a
lot of data here (because of EEE bugs in the Realtek phy layer)
other DSA drivers only return if EEE is available or not for a
port. To make the next kernel upgrade easier follow that design.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
To avoid unneeded interrupts the R4K timer is deactivated during
secondary cpu initialization. This is currently done during
phase init_secondary(). With the upgrade to 6.12 the kernel runs
a primary/secondary cpu timer/counter synchronization to verify the
proper setup in synchronise_count_slave(). That runs at a later
point in time and expects the secondary counter to be fully
functional. Finding a deactivated counter results in the following
messages:
WARNING: CPU: 1 PID: 0 at arch/mips/kernel/sync-r4k.c:99 check_counter_warp+0x220/0x254
Warning: zero counter calibration delta: 0 [max: 6500000]
Counter synchronization [CPU#0 -> CPU#1]:
Measured 278760029 cycles counter warp between CPUs
Relocate the deactivation to smp_finsh() at the end of the cpu
startup sequence. Additionally polish the startup code and remove
all unneeded parts.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Per IEEE 802.3 definition we have:
- parallel XGMII for single 10GBit ONLY links
- serial USGMII for 8 port 1GBit links (not known by kernel)
- serial USXGMII: for single/multiple links with a total bandwidth of 10GBit
The phy-mode of the first eight ports of the XGS1250-12 have always been
defined as XGMII (without S). This came from a confusion with the similar
named Realtek proprietary XSGMII (with S) mode that is basically 10GB SGMII.
From the above definition this is wrong but worked until kernel 6.6. With
the upgrade to 6.12 there is an enforced capabilities check within
phy_caps_from_interface() and link validation fails with
lan1: validation of xgmii with support 62ef and advertisement 62c0 failed: -EINVAL
lan1: failed to connect to PHY: -EINVAL
lan1: error -22 setting up PHY for tree 0, switch 0, port 0
Switch the ports to USXGMII as the most flexible option. This might be no
final solution but at least it better describes the phy/mac link.
Fixes 5b8b382df9 ("realtek: Add support for ZxXEL XGS1250-12 Switch")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix minor compilation errors due to kernel changes.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream has integrated the Realtek target into the generic MIPS
initialization and so MACH_REALTEK_RTL has gained some new features.
Especially:
- CONFIG_MACH_GENERIC_CORE generates central modules
- board-realtek module adds device specific extensions
The current downstream initialization works well and upgrading to
kernel 6.12 is not the right time to harmonize this. Modify the
MACH definitions to the current needs.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
The validate function no longer exists in phylink_mac_ops. Remove
it for the internal ethernet interface. Instead provide some
meaningful mac capabilities.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Not only the link but also the mac capabilities are needed here.
Additionally do some alphabetical sorting.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
The old upstream notation has been changed to something not so racist.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
EEE functions are now called with ethtool_keee instead of
ethtool_eee. Replace all occurrences. This will fix function
signature checks but still produces compilation errors due
to structure changes.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Patches where fuzz had to be cleaned up.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
All these patches needed no manual intervention and applied cleanly
with new source code positions.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Thanks to Chris Packham this driver got upstreamed. Drop the
downstream files and patches.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Automatically generated commit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Automatically generated commit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Automatically generated commit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Automatically generated commit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Automatically generated commit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Automatically generated commit.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add kernel package for Broadcom Settop/DSL I2C controller.
This controller is used on RPi devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This commit changes LAN1 to be WAN and LAN2 to be LAN, like all other
dual port Extreme Networks devices.
This partially reverts commit 84a489b7cf
Signed-off-by: Christian Schmidbauer <github@grische.xyz>
Fixes LAN LED "1" to show activity of LAN1 and LAN LED "2" to show
activity of LAN2, not vice versa.
Signed-off-by: Christian Schmidbauer <github@grische.xyz>
Update the pin-configuration as well as maximum frequency for the eMMC
flash.
- Use 26 MHz as the maximum clock of the eMMC memory
- Configure 12mA as the pin drive-strength
- Enable internal pull-reistors
Signed-off-by: Yin Ni <yin.ni@gl-inet.com>
[adapt commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
The function name is misspelled and does not exist. Fix the function
name so the correct function is called.
Signed-off-by: David Bauer <mail@david-bauer.net>
Multiple users have reported a regression [1] in OpenWRT 24.10 with the
ramips/mt7621 target, which has the MT7530 PHYs: the Ethernet link is
periodically going down for a brief period of time:
mt7530-mdio mdio-bus:1f lan1: Link is Down
br-lan: port 1(lan1) entered disabled state
mt7530-mdio mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
The symptoms stop after disabling EEE and it was reported by Mediatek in
2021 that EEE is unstable for the MT7530 PHYs [2]:
> EEE of the 10-year-old MT7530 internal gephy has many IOT problems, so
> it is recommended to disable its EEE.
EEE is enabled by default for these devices in OpenWRT 24.10 whereas in the
previous version (OpenWRT 23.05, Linux 5.15) it was not. It was determined
that in Linux 6.6, the PHY driver tries to disable EEE in
mtk_gephy_config_init() in drivers/net/phy/mediatek-ge.c, but this is later
overridden by a subsequent execution of the genphy_c45_write_eee_adv()
function, which enables every EEE mode supported.
The best way forward for now seems to be to mark EEE as broken directly in
the devicetree, which affects the genphy_c45_write_eee_adv() function.
There are some devices, like GnuBee GB-PC2, that define additional PHYs,
for example ethernet-phy@5 or ethernet-phy@7. As reported by Chester A.
Unal, these are not MT7530 PHYs and they are not affected.
This would need to be cherrypicked for the OpenWRT 24.10 branch.
[1] https://github.com/openwrt/openwrt/issues/17351
[2] https://lore.kernel.org/all/0adde34f936a2dafca40b06b408d82afe0852327.camel@mediatek.com/
Tested-by: Darren Tucker
Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl>
Closes: https://github.com/openwrt/openwrt/issues/17351
Link: https://github.com/openwrt/openwrt/pull/18585
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specifications:
- SoC: Broadcom BCM6358 dual 300MHz MIPS
- Flash: 16MB NOR Macronix MX29GL128EHT2I-90G
- RAM: 64MB DDR
- Ethernet: 4x 100M
- Wifi: Ralink RT3062F
- 3x USB 2.0 port
- 4x Button
- 13x LED
- RJ11 2x FXS VoIP (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
- Assign static IP 192.168.1.100 to PC.
- Unplug the power source.
- Press the RESTART button at the router, don't release it yet!
- Plug the power source and wait at least 15 seconds.
- Release the RESTART button.
- Browse to http://192.168.1.1 with your PC.
- Upload the openwrt-bmips-bcm6358-huawei_hg556a-c-squashfs-cfe.bin file.
- Wait some minutes until the firmware upgrade completes.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
It's time to give the patches documentation some love by:
- Using Markdown.
- Differentiating between generic and specific target patches.
- Adding deeper explanation about patch numbering.
Link: https://github.com/openwrt/openwrt/pull/19092
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Missing headers causes an error on kernel 6.12:
arch/mips/ralink/irq.c:86:5: error: no previous prototype for 'get_c0_perfcount_int' [-Werror=missing-prototypes]
86 | int get_c0_perfcount_int(void)
| ^~~~~~~~~~~~~~~~~~~~
arch/mips/ralink/irq.c:92:14: error: no previous prototype for 'get_c0_compare_int' [-Werror=missing-prototypes]
92 | unsigned int get_c0_compare_int(void)
| ^~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18654
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Replace macros with empty body with 'do {} while (0)'.
Remove unnecessary semicolons.
Fixes:
drivers/mmc/host/mtk-mmc/sd.c: In function 'msdc_irq':
drivers/mmc/host/mtk-mmc/sd.c:1969:87: error: suggest braces around empty body in an 'else' statement [-Werror=empty-body]
1969 | IRQ_MSG("XXX CMD<%d> MSDC_INT_RSPCRCERR", cmd->opcode);
| ^
drivers/mmc/host/mtk-mmc/sd.c:1975:84: error: suggest braces around empty body in an 'else' statement [-Werror=empty-body]
1975 | IRQ_MSG("XXX CMD<%d> MSDC_INT_CMDTMO", cmd->opcode);
| ^
cc1: all warnings being treated as errors
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18654
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reorganize backported 6.12 generic patches, grouping them by following
a standard naming XXX-XX-v6.x-patch-file-name.patch.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add kernel package for DesignWare I2C platform controller.
This controller is used on the RP1 SoC found on RPi 5 devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add kernel packages for DesignWare SPI core and MMIO controllers.
This is needed for the RP1 SoC found on RPi 5 devices.
Tested with a Microchip ENC28J60 Ethernet controller on a RPi 5.
Signed-off-by: Albrecht Lohofener <albrechtloh@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19049
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add uboot-envtools (removing -uboot-envtools) to devices which were
missed in the commit 79bd017 ("ramips: mt7621: add uboot-envtools to
all devices")
- Mi Router 3G
- Mi Router AC2100
While at here remove two redundant entries from devices which were added
just after the referenced commit 79bd017 and did not account for the
new DEFAULT_PACKAGES member:
- SNR-CPE-ME1
- SNR-CPE-ME2-SFP
Fixes: 79bd017 ("ramips: mt7621: add uboot-envtools to all devices")
Fixes: https://github.com/openwrt/openwrt/issues/18960
Signed-off-by: Mario Andrés Pérez <mapb_@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19012
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the following to fix builds with GCC 15.1:
https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/arch/mips/vdso?h=next-20250606&id=0f4ae7c6ecb89bfda026d210dcf8216fb67d2333
% dmesg | grep gcc
[ 0.000000] Linux version 6.6.93 (facade@redline) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 15.1.0 r29972+15-7d617804cfe7) 15.1.0, GNU ld (GNU Binutils) 2.44) #0 SMP Sat Jun 7 12:13:18 2025
Error for reference:
./include/linux/stddef.h:11:9: error: cannot use keyword 'false' as enumeration constant
11 | false = 0,
| ^~~~~
./include/linux/stddef.h:11:9: note: 'false' is a keyword with '-std=c23' onwards
./include/linux/types.h:35:33: error: 'bool' cannot be defined via 'typedef'
35 | typedef _Bool bool;
| ^~~~
./include/linux/types.h:35:33: note: 'bool' is a keyword with '-std=c23' onwards
./include/linux/types.h:35:1: error: useless type name in empty declaration [-Werror]
35 | typedef _Bool bool;
| ^~~~~~~
CC arch/mips/lib/delay.o
AR arch/mips/fw/lib/built-in.a
AR arch/mips/fw/lib/lib.a
CC arch/mips/ralink/of.o
CC fs/read_write.o
CC block/elevator.o
cc1: all warnings being treated as errors
make[9]: *** [scripts/Makefile.build:243: arch/mips/vdso/vgettimeofday.o] Error 1
make[8]: *** [scripts/Makefile.build:480: arch/mips/vdso] Error 2
Build system: x86/64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/19058
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch contains various minor FDT improvements for ramips
HiWiFi series devices:
* Add mt76 driver compatibles.
* Remove useless platform compatibles.
* Add default USB LED trigger for HC5861.
* Disable unused usbphy for HC5661, HC5661A and HC581B.
* Add switch port map properties based on 02_network scripts.
* Move aliases node to device dts because the LED nodes it
references only exist in the device specific dts.
* Rename gpio-leds nodes to follow the upstream dt-bindings
suggested pattern "(^led-[0-9a-f]$|led)".
* Convert deprecated LED label property to color and function.
"system" LED has been renamed to "status", it is acceptable
because these LEDs do not have text labels.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18251
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
For all HiWiFi series devices, the base MAC address is stored on
"bdinfo" partition, offset 0x18a, ASCII text format. The recently
introduced "mac-base" nvmem layout can handle the ASCII text now,
so it's time to move MAC address configurations to dts. There is
no valid MAC info in the "factory" partition, hence they will be
replaced with the correct ones.
Tested on HiWiFi HC5661A and HC5861.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18251
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specifications:
- SoC: Broadcom BCM6358 dual 300MHz MIPS
- Flash: 16MB NOR Spansion S29GL128P10
- RAM: 64MB DDR
- Ethernet: 4x 100M
- Wifi: Atheros AR9223
- 3x USB 2.0 port
- 4x Button
- 13x LED
- RJ11 2x FXS VoIP (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
- Assign static IP 192.168.1.100 to PC.
- Unplug the power source.
- Press the RESTART button at the router, don't release it yet!
- Plug the power source and wait at least 15 seconds.
- Release the RESTART button.
- Browse to http://192.168.1.1 with your PC.
- Upload the openwrt-bmips-bcm6358-huawei_hg556a-a-squashfs-cfe.bin file.
- Wait some minutes until the firmware upgrade completes.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Commit Fixes: 15430a1348 ("bmips: use wan ports as standalone ports")
removed bridge devices and therefore switch.1 no longer exists, so let's
use br-lan instead.
Fixes: 15430a1348 ("bmips: use wan ports as standalone ports")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The Arcadyan WE410443 is a WiFi AC access point distributed by various ISPs
under various names, including KPN SuperWifi and BT Whole Home Wi-Fi. It
features one ethernet port, dual MT7615N radios and four internal antennas.
Hardware:
- SoC: Mediatek MT7621AT
- Flash: 32 MB
- RAM: 128 MB
- Ethernet: 1x 10/100/1000 Mbps, built into the SoC
- WLAN: 2x MediaTek MT7615N
- Buttons: 1 Reset button, 1 WPS button
- LEDs: 1x Green, 1x Blue, 1x Red, all unmarked
- Power: 12 VDC, 1.5A barrel plug
Installation:
The bootloader is locked with a password, so the image needs to be written
directly to the SPI flash chip. To do this, you need to open up the case,
remove the heatsink and connect the flash chip to a Raspberry Pi. Use the
following connections:
Flash chip --> Raspberry Pi
VCC --> 3v3
RESET --> 3v3
/CS --> GPIO 8
DO --> GPIO 9
CLK --> GPIO 11
DI --> GPIO 10
GND --> Ground
You can solder wires to the flash chip, or use a SOIC16 clip. More details on
the Raspberry Pi and SPI chip pinouts are available on the wiki [1]
When you have the Raspberry Pi connected to the flash chip, boot your Pi and
follow the instructions:
1) Make sure your Pi has SPI enabled with sudo raspi-config
2) Install necessary tools: sudo apt install xxd libubootenv-tool mtd-utils
3) Upload overlay and execute:
sudo dtc -@ -I dts -O dtb -o
/boot/overlays/we410443.dtbo we410443-overlay.dts
4) Enable in /boot/firmware/config.txt by adding a new line containing
dtoverlay=we410443
5) Reboot your Pi and verify the mtd partitions with
cat /proc/mtd, you should see:
dev: size erasesize name
mtd0: 02000000 00001000 "all"
mtd1: 00030000 00001000 "u-boot"
mtd2: 00010000 00001000 "u-boot-env"
mtd3: 00010000 00001000 "factory"
mtd4: 01f60000 00001000 "firmware"
mtd5: 00010000 00001000 "glbcfg"
mtd6: 00010000 00001000 "config"
mtd7: 00010000 00001000 "glbcfg2"
mtd8: 00010000 00001000 "config2"
6) Optionally (but recommended), make a backup:
sudo dd if=/dev/mtd0 of=backup.bin
It can be restored with: sudo flashcp backup.bin /dev/mtd0
7) Set the variables for the bootloader:
echo '/dev/mtd2 0x0 0x1000 0x1000' > fw_env.config
sudo fw_setenv -c fw_env.config bootpartition 0
8) Finally, flash the image:
sudo flashcp openwrt-ramips-mt7621-arcadyan_we410443-
squashfs-sysupgrade.bin /dev/mtd4
MAC addresses
The label address is stored in ASCII in the config partition
Use --> Address
Device --> label
Ethernet --> label
WLAN 2g --> + 1
WLAN 5g --> + 2
References:
[1] https://openwrt.org/toh/arcadyan/astoria/we410443
Signed-off-by: Sander van Deijck <sander@vandeijck.com>
Link: https://github.com/openwrt/openwrt/pull/17981
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
- Fix MMC bus IO voltage. The GPIO voltage of mt762x series SoCs
is fixed 3.3V. There are no visible registers that can control
the voltage level. Also add "no-1-8-v" property to indicate that
MMC controller doesn't support 1.8V IO.
- Drop useless property "enable-active-high". These dummy fixed
voltage regulators are not controlled by the GPIO. We don't need
to set the GPIO polarity.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18886
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To simplify the device specific dts, reuse the mt7621 default
XHCI voltage regulators by adding the corresponding GPIO pin
and polarity properties.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18886
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We have added the default voltage regulators for the mt7621 SoC
dtsi. These redundant voltage regulators can be removed now.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18886
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The USB power regulators are essential for the Mediatek XHCI
controller. If any of them is missing, the kernel will throw
a warning. Add fixed voltage io/vbus regulators to workaround
this issue. Fix the following warnings:
[ 7.514572] xhci-mtk 1e1c0000.xhci: supply vbus not found, using dummy regulator
[ 7.522375] xhci-mtk 1e1c0000.xhci: supply vusb33 not found, using dummy regulator
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18886
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The WR3000E has the same board layout as the WR3000S. Differences:
- Different flash chip
- LEDs with red/blue colour intead of white
Hardware:
- MediaTek MT7981 WiSoC
- 256MB DDR3 RAM
- 128MB SPI-NAND (F50L1G41LB)
- MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
MAC Addresses in OEM firmware:
- There is one on the label, e.g. AA:BB:CC:DD:EE:FF
- WLAN (2.4G) uses the same as on the label
- WLAN (5G) is the one on the label but
- first byte (e.g. AA) + 2
- fourth byte (e.g. DD) - 0x40
- WAN is the one on the label + 1
- LAN is the one on the label
MAC Addresses in OpenWrt:
- Same handling as in WR3000s is used
GPIO:
- 2 Buttons (all low active):
- WPS on GPIO 0
- Reset on GPIO 1
- 6 LEDs (all low active):
- Power: Blue on GPIO 8, no red LED
- WPS: Blue on GPIO 10, Red on GPIO 4
- Internet: Blue on GPIO 11, no red LED
- LAN: Blue on GPIO 9, Red on GPIO 5
- WiFi 2.4G: Blue on GPIO 6, no red LED
- WiFi 5G: Blue on GPIO 7, no red LED
Disassembly:
- Remove the 4 screws at the bottom of the case
- Cover is clipped to the bottom part of the case with clips in the front and the back
UART:
- UART pins are accessible on the bottom of the board
- The connector with the square shape is TX
- Pins: [ ] TX, ( ) RX, ( ) GND, ( ) VCC
- Settings: 115200 8N1 3.3V
Migration to OpenWrt via OEM firmware:
- There should be a migration image available from Cudy as soon as there is official OpenWrt support
- Download the migration image via OEM web interface
- After flashing, OpenWrt is accessible via 192.168.1.1
- Flash the official OpenWrt image
Migration to OpenWrt using TFTP:
- Connect UART as described above
- Press the reset button while powering on the device
- U-Boot will now try to load a recovery.bin via TFTP, this must be ignored
- After detecting a timeout, the U-Boot console is available via UART
- Set up a TFTP server on IP 192.168.1.88 and connect it to one of the LAN ports
- Provide the initramfs image via TFTP as cudy3000e.bin
- Run the following command in U-Boot: tftpboot 0x46000000 cudy3000e.bin; bootm 0x46000000
- OpenWrt initramfs image is now booting and accessible via 192.168.1.1
- Flash the sysupgrade image
Revert back to OEM:
- Set up a TFTP server on IP 192.168.1.88 and connect it to one of the LAN ports
- Provide the Cudy firmware via TFTP as recovery.bin
- Press the reset button while powering on the device
- Recovery process will start now
- After recovery is done, the OEM firmware is available at 192.168.10.1 again
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18609
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With the recent fixes backported to 6.12, b53 ports should now fully
work as standalone ports outside of a switch.
So move them out of the switch and use them as standalone ports, which
makes configuring easier as VLANs don't need to be defined and reserved
anymore to use the wan port.
Tested on DGND3700v1.
While most devices do not define a wan port, I dropped the
ucidef_set_bridge_device() from all devices for consistency.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Allow selecting 6.12 as testing kernel on imx.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19029
Signed-off-by: Nick Hainke <vincent@systemli.org>
patches:
- remove patches from 6.7-6.12 that are now upstream.
- refresh remaining patches
- 502-6.13-arm64-dts-freescale-rename-gw7905-to-gw75xx.patch was
misnamed as that patch went upstream in 6.12 and thus is also removed
- 504-6.13-arm64-dts-imx-Add-i.MX8M-Plus-Gateworks-GW82XX-2X-support.patch
was refreshed to the final version that was accepted upstream
- 600-PCI-imx6-Start-link-at-max-gen-first-for-IMX8MM-and-IMX8MP.patch
was removed while I investigate an upstream approach for the issue
it was working around.
configs:
- config-6.12: unset new configs not needed for all cortexa7/a9/a53
- cortexa53/config-default: added new CONFIG_PCI_IMX6_HOST config for cortexA53 (IMX8M)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19029
Signed-off-by: Nick Hainke <vincent@systemli.org>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19029
Signed-off-by: Nick Hainke <vincent@systemli.org>
They don't need +x permission.
Fixes: 502916468e ("ramips: add support for ASUS 4G-AX56")
Signed-off-by: Zheng Zhang <everything411@qq.com>
Link: https://github.com/openwrt/openwrt/pull/19034
Signed-off-by: Nick Hainke <vincent@systemli.org>
This change moves common elements of the WR3000H and the WR3000S to mt7981b-cudy-wr3000-nand.dtsi.
This will simplify adding of new similar devices, for exapmle WR3000E.
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18619
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rather than hardcoding the kernel/fdt addresses in the boot.scr script,
use the addresses provided by the bootloader.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
- refresh, rebase and reorder patches
- JH7110 media drivers have been dropped for now
- JH7110 E24 and mailbox drivers were added
- JH7100 DMA- and errata-patches have been dropped as they were
upstreamed
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
archs38 has been on life support for the last couple of releases,eventually
leading to marking it as source-only in 2023.
It has been basically only touched to do a kernel bump so that we can make
the new OpenWrt release.
Link: https://github.com/openwrt/openwrt/pull/19001
Signed-off-by: Robert Marko <robimarko@gmail.com>
Allow the armsr target to be built with a 6.12 kernel
when CONFIG_TESTING_KERNEL is set.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Link: https://github.com/openwrt/openwrt/pull/18849
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This includes both new additions to 6.12
and an attempted "refresh" of the config
to remove duplicates from target/generic/config-6.12.
(The OpenWrt kernel_makeoldconfig does not
work well with the armv8 subtarget for reasons
I am yet to determine, so that file has been
pruned manually)
Most new options are in armv8, where the
KConfig relates to a platform that will likely
be armsr compatible (like the i.MX91/93/95),
it has been enabled.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Link: https://github.com/openwrt/openwrt/pull/18849
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Introduced with Linux 6.7, in commit:
5c2f7727d437 ("mtd: mtdpart: check for subpartitions parsing result"),
when a parser returns an error, this will be passed up, and
consequently, all parent mtd partitions get torn down.
Adjust the mtdsplit_uimage driver to only return an error if there is a
critical problem in reading from the mtd device or allocating memory.
Otherwise return 0 to indicate that no partitions were found.
Also add logging to indicate what went wrong.
E.g. on Realtek devices that are booted for the first time through
initramfs with OpenWrt never installed before boot log will show
[ 0.932985] Creating 8 MTD partitions on "spi0.0":
[ 0.938412] 0x000000000000-0x000000080000 : "u-boot"
[ 0.990151] 0x000000080000-0x0000000c0000 : "u-boot-env"
[ 0.999907] 0x0000000c0000-0x000000100000 : "board-name"
[ 1.019971] 0x000000100000-0x000000e80000 : "firmware"
[ 1.051582] mtdsplit_uimage: no uImage found in "firmware"
[ 1.069365] 0x000000e80000-0x000001000000 : "kernel2"
[ 1.078959] 0x000001000000-0x000001040000 : "sysinfo"
[ 1.099747] 0x000001040000-0x000001c40000 : "rootfs2"
[ 1.119865] 0x000001c40000-0x000002000000 : "jffs2"
Similar issue was fixed before with commit ade045084b
("kernel: mtdsplit_minor: return 0 if not fatal")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19016
Signed-off-by: Robert Marko <robimarko@gmail.com>
GL.iNet shipped a hardware change of the WAN PHY going from the MaxLinear
GPY211C to the Airoha EN8811H.
Signed-off-by: Matthew Bilker <me@mbilker.us>
Link: https://github.com/openwrt/openwrt/pull/18799
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Trying to use modules for the PHY:s does not work:
The ethernet driver does not like to probe if it can't find
the PHY.
The ethernet driver really likes to be compiled-in. It will
not probe otherwise. Some hardware issue.
Revert things to how they always worked until I maybe solve
this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Extends SoC thermal sensor on rtl839x
* Tested on HP JG928A
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
Link: https://github.com/openwrt/openwrt/pull/18825
Signed-off-by: Robert Marko <robimarko@gmail.com>
Regulators as implemented by the XHCI driver only accept one GPIO.
However, we can abuse the fact that the XHCI driver accepts two
regulators, one for 5V and the other for 3.3V, for USB 2 and 3 GPIOs.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16967
Signed-off-by: Robert Marko <robimarko@gmail.com>
This can be done with so little effort, all but two patches are now
upstream. No need to keep support for v6.6, everything just works
the same or better with v6.12.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The resets in the GCC of the uniphy found in the IPQ5018 SoC are
incorrect which broke the ability to shift between 1G and 2.5G link
speeds. So let's correct the resets based on below two downstream
commits.
In a seperate and prequisite PR to the QCA-SSDK repo, logic has been
implemented to select the right reset based on the link setup so fixed
link scenarios don't break.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18774
Signed-off-by: Robert Marko <robimarko@gmail.com>
Ahead of the actual fix in both the GCC and QCA-SSDK, add the required
AHB reset so it can be picked up by updated QCA-SSDK. This is needed
as the SSDK needs to use different resets depending on the link
architecture. If it's a fixed link, AHB needs to be reset. In a phy to
phy link setup (such as QCA8081), SYS, RX, and TX need to be reset using
one reset with a bitmask in the GCC (GCC_UNIPHY_SOFT_RESET).
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18774
Signed-off-by: Robert Marko <robimarko@gmail.com>
With completely carving out GE PHY out of the QCA-SSDK, the named clock
references to the GE PHY RX and TX clocks are no longer needed.
So, let's revert to using the DT indices as per the upstream GCC driver.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18774
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use latest patches sent upstream for review for IPQ5018 GE PHY support:
- Move enablement of the LDO controller to the mdio-ipq4019 driver away
from the CMN PLL driver
- Remove the different patches to add CDT, MSE, AZ, and DAC support they
are all contained in the upstreamed driver.
Accordingly, also set the right property in the DTS for Linksys SPNMX56
to set the right DAC values to accommodate for the short cable length.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18774
Signed-off-by: Robert Marko <robimarko@gmail.com>
kmod-fs-ntfs is not available on the 6.12 kernel.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18954
Signed-off-by: Robert Marko <robimarko@gmail.com>
As qualcommbe is now supported by the v6.12 kernel, there is no point
in v6.6 as well. Drop v6.6 support.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18982
Signed-off-by: Robert Marko <robimarko@gmail.com>
The qualcommbe target was introduced after openwrt-24.10. The v6.12
kernel is now available, and is likely to be used by the next openwrt
release.While the v6.6 kernel served as an interim development vehicle,
it is no longer useful for the qualcommbe target
The v6.12 patches contain more recent submissions of pending ipq95xx
drivers. I expect that it will be much easier to update v6.12 patches
with new submissions. For ease of maintenance, it makes sense to use
a single kernel for qualcommbe.
For these reasons, enable v6.12 by default.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18982
Signed-off-by: Robert Marko <robimarko@gmail.com>
The external switch of the Huawei HG556a is a BCM5325E connected by MDIO.
All the DSA brcm legacy FCS tag and b53 patches have been submitted upstream
and will be backported when accepted.
There are still some sporadic FDB errors, but at least the switch is working
and stable on my device:
bcm53xx fffe4800.ethernet-mii:1e: port 0 failed to add 72:31:59:xx:xx:xx vid 1 to fdb: -28
bcm53xx fffe4800.ethernet-mii:1e: port 0 failed to add 5c:4c:a9:xx:xx:xx vid 0 to fdb: -28
bcm53xx fffe4800.ethernet-mii:1e: port 0 failed to add 5c:4c:a9:xx:xx:xx vid 1 to fdb: -28
bcm53xx fffe4800.ethernet-mii:1e: port 0 failed to delete 72:31:59:xx:xx:xx vid 1 from fdb: -2
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add support for V3 of the Engenius EWS2910P PoE switch. Like its v1
brother, This is an RTL8380 based switch with two SFP slots, and PoE
802.3af one every RJ-45 port.
Unlike its older brother, the max budget is 55W instead of 61.6 W.
Investigation into the communication protocol with the PoE controller
is ongoing, though it appears the vendor firmware configures the PSE
with a per-port budget of 30.0W.
Specifications:
---------------
* SoC: Realtek RTL8380M
* Flash: 32 MiB SPI flash Macronix MX25L25635E
* RAM: 256 MiB (As reported by bootloader)
* Ethernet: 8x 10/100/1000 Mbps with PoE
2x SFP slots
* Buttons: 1 "Reset" button on front panel
1 "LED mode: button on front panel
1 "On/Off" Toggle switch on the back
* Power: 48V-54V DC barrel jack
* UART: 1 serial header (JP1) with populated 2.54mm pitch header
Labeled GRTV for ground, rx, tx, and 3.3V respectively
* PoE: 1 STM ST32... microcontroller (U15)
1 RTL8238B PSE controller
Works:
------
- (8) RJ-45 ethernet ports
- Switch functions
- LEDs and buttons
Not yet enabled:
----------------
- Power-over-Ethernet (requires realtek-poe support for RTL8232B)
Install via web interface:
-------------------------
The factory firmware will accept and flash the initramfs image. It is
recommended to flash to "Partition 0". Flashing to "Partition 1" is
not supported at this point.
The factory web GUI will show the following warning:
" Warning: The firmware version is v0.00.00-c0.0.00
The firmware image you are uploading is older than the current
firmware of the switch. The device will reset back to default
settings. Are you sure you want to proceed?"
This is expected when flashing OpenWrt. After the initramfs image
boots, flash the -sysupgrade using either the commandline or LuCI.
Install via serial console/tftp:
--------------------------------
See commit 2cfaab4549 ("realtek: add support for EnGenius EWS2910P").
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15217
Signed-off-by: Robert Marko <robimarko@gmail.com>
When the Engenius EWS-2910P was added, only v1 was known. Move the
common parts to a dtsi, and split up the support to acccount for the
hardware version.
On v3, for example, the root partition uses a different uImage magic.
Add a "engenius,ews2910p-v1" compatible, while leaving the legacy
"engenius,ews2910p" to also mean v1.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15217
Signed-off-by: Robert Marko <robimarko@gmail.com>
DSA silently drops internal phy access to ports >= 32 in dsa_user_phy_read()
and dsa_user_phy_write(). The code shows:
static int dsa_user_phy_read(struct mii_bus *bus, int addr, int reg)
{
struct dsa_switch *ds = bus->priv;
if (ds->phys_mii_mask & (1 << addr))
return ds->ops->phy_read(ds, addr, reg);
return 0xffff;
}
With ds->phys_mii_mask being a 32 bit variable the reason is clear. So do
not only increase the max values but also adapt the needed bitmasks in
the dsa and phy code. This fixes the dsa_user_ports() and dsa_cpu_ports()
too.
While we are here combine the old separated patches because dsa, mdio and
phy are tigthly coupled.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18846
Signed-off-by: Robert Marko <robimarko@gmail.com>
The PCS driver in the 6.12 patchset is the v5 submission (see link
below). It solves a number of issues and crashes with teh pcs driver
from the 6.6 patchset. However, this new driver is missing support for
"10gbase-r", "10g-qxgmii", and 1000/2500base-x modes.
Port these modes to the 6.12 patchset. "2500base-x" in particular seems
to be needed to establish a 2.5G link on phy-mode="usxgmii";
Link: https://lore.kernel.org/lkml/20250207-ipq_pcs_6-14_rc1-v5-0-be2ebec32921@quicinc.com/
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that patches for v6.12 are available, add the config, and enable
6.12 as a testing kernel.
Compared to v6.6 the patches to add "10gbase-r", "2500base-x",
"1000base-x", and "10g-qxgmii" modes have not been ported yet. They do
not apply cleanly to the new PCS driver. As the currently supported
hardware does not use those modes, it is not possible to test them at
this time.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Copy the v6.6 config to v6.6. It will be updated in a subsequent
commit in order to show the changes.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Port reset and clock fixes from target/linux/qualcommbe/patches-6.6.
Modifications of v6.6 patches are noted in each commit body.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that ethernet is supported on IPQ9574, add the port nodes and
other requirements to enable ethernet on RDP433.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add the second part of the PPE driver. This includes the EDMA and
network device support. This part does not appear to have been
officially submitted for upstream review. The series is taken from
target/linux/qualcommbe/patches-6.6, and had to be heavily modified
in order to compile of v6.12. Changes to patches are noted in the
respective patch body.
Also add the PPE and EDMA nodes in this series.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add the v5 of the PCS patch. This is the latest submission as of this
writing. THe last four patches are not part of the submission. They
make the series work with v6.12 kernel, resolve a circular dependency
with the clocks, and add the DTS node. Include them as bundle.
Link: https://lore.kernel.org/lkml/20250207-ipq_pcs_6-14_rc1-v5-0-be2ebec32921@quicinc.com/
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
This driver is cherry-picked from target/linux/qualcommbe/patches-6.6.
While Qualcomm did submit past patches for QCA8084, the code has since
ben split from at803x. The existing OpenWRT version of the patch is
the cleanest version I could find. Add it here.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
These devicetree updates can work with the existing upstreamcode. They
do not require code changes. Add them before any code change.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add dts fixes from linux-next. Two patches from the NSSCC series are
still in -next did not yet land in mainline, as well as misc other DTS
changes. Add them here.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add relevant patches from upstream, up to v5.16-rc6. The gaps in the
patch numbersing are either patches that were picked into the stable
kernel (6.12.y), or that are already backported in
target/linux/generic. The gaps makes it easy for me to pick these
patches from my working kernel git branch.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that we have a board file, add calibration variant for TP-Link
Archer C6 v2 and add ipq-wifi package for it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
RTC has been disabled so far in the cortexa53 subtarget so far, enable
it. It's also required for the crypto trng/prng drivers on these SoC
variants (to gather IOSC noise).
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This symbol was lost when porting to the 6.12 kernel.
Fixes: 16b5a77716 ("mediatek: mt7629: update config-6.12")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18947
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All four subtargets build successfully and run under QEMU.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18712
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Drop obsolete symbols GCC_ASM_GOTO_OUTPUT_WORKAROUND and HW_CONSOLE, and
PREEMPT_NONE_BUILD which is now set in top-level generic config.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18712
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18712
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These packages were dropped off in reverted packaging, bring
them all back.
Link: https://github.com/openwrt/openwrt/pull/18952
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Update subtarget configs for kernel 6.12.
- Refresh patches for kernel 6.12.
- Drop 210-revert-macronix-nand-block-protection.patch since brcmnand no longer
implements low level ops.
- Adapt bcm63268 gpio switches for 6.12 numbering.
- Add b53 pending patches from Jonas Gorski to fix system hangs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This is an automatically generated commit which aids following kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The support_eee patch is needed in order to prevent system hangs on bmips
devices.
c4f873c2b65c8 net: dsa: b53: mdio: add support for BCM53101
c86692fc2cb77 net: dsa: b53/bcm_sf2: implement .support_eee() method
f12b363887c70 net: dsa: use ethtool string helpers
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
These patches are needed for b53 implementation of b53_support_eee, which
prevent system hangs on bmips devices.
99379f587278c net: dsa: provide implementation of .support_eee()
9723a77318b7c net: dsa: add hook to determine whether EEE is supported
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
The driver tries to access ioports (0x2f9!!) which UML doesn't have.
This causes lots of warnings to appear on boot:
| WARNING: CPU: 0 PID: 1 at lib/logic_iomem.c:188 serial8250_config_port+0x20a/0x1260
| Invalid writeqb of 0xff at address 2f9
| Modules linked in:
| CPU: 0 UID: 0 PID: 1 Comm: swapper Tainted: G W 6.12.25 #0
| Tainted: [W]=WARN
| Stack:
| Call Trace:
| [<60001000>] ? set_reset_devices+0x0/0x16
| [<60452cba>] ? serial8250_config_port+0x20a/0x1260
| [<6071e91f>] ? dump_stack_lvl+0x55/0x71
| [<606e127c>] ? _printk+0x0/0x4f
| [<60044bbb>] ? __warn+0x11b/0x120
| [<6003b5d0>] ? um_set_signals+0x0/0x40
| [<606de721>] ? warn_slowpath_fmt+0x81/0x8c
| [<606de6a0>] ? warn_slowpath_fmt+0x0/0x8c
| [<60452cba>] ? serial8250_config_port+0x20a/0x1260
(they are even recursive!)
Now, the situation gets more confusing. Because from what I can tell,
this was seemingly done intenionally. Upstream patches in related areas:
|commit ddd268c42871b78c75e12a5c28207fb481138f41
|Author: Niklas Schnelle <schnelle@linux.ibm.com>
|Date: Wed Apr 3 14:43:00 2024 +0200
|
| um: Select HAS_IOREMAP for UML_IOMEM_EMULATION
|
| In a future patch HAS_IOPORT=n will disable inb()/outb() and friends at
| compile time. UML supports these via its UML_IOMEM_EMULATION so let that
| select HAS_IOPORT and also reflect this in NO_IOPORT_MAP.
hint that there's ongoing work in this area. But unfortunately, this future
hasn't arrived yet. Once this future arrives, please nuke this patch.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
refresh config + patches.
This includes the following changes:
- The selected x86_64 CPU is switched to generic instead of K8.
A backported patch is included from 6.13.
000-v6.13-asm-generic-io.h-rework-split-ioread64-iowrite64-hel.patch
|fixed the following build error:
| CC lib/iomap.o
|lib/iomap.c:156:5: error: no previous prototype for 'ioread64_lo_hi' [-Werror=missing-prototypes]
| 156 | u64 ioread64_lo_hi(const void __iomem *addr)
| | ^~~~~~~~~~~~~~
| [...]
Note: 102-pseudo-random-mac.patch will likely go away with the next stable.
UML is switching to a new networking infrastructure. The previous implementation
using tuntap, daemon, socket, ethertap, vde are being replaced by "vector"
transports tap, hybrid, raw, EoGRE, Eol2tpv3, fd, vde (vector!).
Please see, to checkout what will change:
<https://docs.kernel.org/virt/uml/user_mode_linux_howto_v2.html#setting-up-uml-networking>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This should have been fixed by an upstream patch in 5.12
|commit ed102bf2afed226703eaf85a704755bdbea34583
|Author: Randy Dunlap <rdunlap@infradead.org>
|Date: Thu Apr 15 10:13:52 2021 -0700
|
| um: Fix W=1 missing-include-dirs warnings
|
| Currently when using "W=1" with UML builds, there are over 700 warnings
| cc1: warning: ./arch/um/include/uapi: No such file or directory [-Wmissing-include-dirs]
|
| but arch/um/ does not have include/uapi/ at all, so add that
| subdir and put one Kbuild file into it (since git does not track
| empty subdirs).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
this symbol got picked up by the 6.12 UML conversion.
CONFIG_FBNIC = FaceBook/Meta Platforms Host Network Interface
it should be disabled by default in generic.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This is needed for mac80211 v6.14.5 update.
9934a1bd45b2b clk: provide devm_clk_get_optional_enabled_with_rate()
9934a1bd45
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This is needed for mac80211 v6.14.5 update.
b35108a51cf7b jiffies: Define secs_to_jiffies()
bb2784d9ab495 jiffies: Cast to unsigned long in secs_to_jiffies() conversion
b35108a51cbb2784d9ab
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
New revision Arcadyan Mozart apply a new partition table and moved the
factory partition to a new location. This conflicts with the standard
partition layout and also make the nvmem cells to not correctly identify
the MAC address anymore.
Generate and Provide a new GPT partition table that account for the new
calibration partition.
The previous revision of the Arcadyan Mozart device is considered
pre-production devices and should not be intended for real support.
Link: https://github.com/openwrt/openwrt/pull/18874
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
ALFA Network AP120C-AX is a dual-band ceiling AP, based on Qualcomm
IPQ6000 + QCN5021 + QCN5052 + QCA8072 chipsets bundle.
Specifications:
- SOC: Qualcomm IPQ6000 (quad-core Cortex-A53 1.2 GHz)
- DRAM: DDR3 512 MB (Micron MT41K256M16TW-107)
- Flash: 16 MB SPI NOR (Macronix MX25U12832F, boot device)
128 MB NAND (Macronix MX30UF1G18AC, dual-firmware)
- Ethernet: 2x 10/100/1000 Mbps Ethernet (QCA8072)
802.3at/af PoE input in WAN port
- Wi-Fi: 2x2 2.4 GHz Wi-Fi 6 (QCN5021 + RFFM8227 FEM)
2x2 5 GHz Wi-Fi 6 (QCN5152 + QPF4568 FEM)
- Antenna: for indoor version: dual-band, internal
2x (or 4x) U.FL antenna connectors on the PCB
- LED: for indoor/outdoor versions: 5x on external module (status,
2x Wi-Fi, 2x Ethernet), PoE LED on-board
8-pin on-board header for LED module (1.27 mm pitch, J14)
- Button: 1x button (reset)
- USB: 1x 4-pin on-board header for USB 2.0 (2.54 mm pitch, J22)
- UART: 1x micro USB Type-B for system console (Holtek HT42B534)
1x 4-pin on-board header (2.54 mm pitch, J11)
- Power: 802.3at/af PoE or 12 V DC/2 A (DC jack)
- Other: 8-pin and 4-pin on-board headers for external Bluetooth
module (1.27 mm pitch, J15, J16, unavailable, thus untested)
MAC addresses:
- WAN: 00:c0:ca:xx:xx:6c (art 0x0, device's label -2)
- LAN: 00:c0:ca:xx:xx:6d (art 0x6, device's label -1)
- 2.4 GHz (IPQ6000): 00:c0:ca:xx:xx:6e (art 0xc, device's label)
- 5 GHz (IPQ6000): 00:c0:ca:xx:xx:6f (device's label + 1)
Flash instructions:
Due to the lack of direct GUI based update capability and dual-firmware
partition configuration, it is recommended to use TFTP + serial console
based approach (console is available in micro USB connector):
1. Set a static IP 192.168.1.1/24 on PC and start TFTP server with the
'...-factory.ubi' image renamed to 'firmware.bin'.
2. Make sure you can access board's serial console over micro USB.
3. Power up the device, hit any key to enter U-Boot CLI and issue below
commands.
3.1 Restore U-Boot's environment to default values (double check first
the '0:APPSBLENV' partition offset using 'smem' command):
sf probe
sf erase 0x510000 0x10000
saveenv
3.2 Download and install OpenWrt in both partitions and reset the board:
tftpb 0x44000000 firmware.bin
flash rootfs
flash rootfs_1
reset
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This platform is tightly coupled to upstream and works just
fine with kernel v6.12.
Link: https://github.com/openwrt/openwrt/pull/18936
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a few ARM-related kconfig options that makes the
configure phase smooth on ARM (32bit) systems.
We default PAN to enabled for protection, however this has
a syscall speed penalty, if your system is interacting a lot
from userspace you might want to disable it for speed vs
security. For in-kernel routing it should not be a major
issue.
Some marginal ARM system enables DRM so make sure we have
the related DRM Kconfigs set up to unselected.
Link: https://github.com/openwrt/openwrt/pull/18900
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This allows us to use the full size of nand, which increases ubi size
from 64M to 122.25M.
If you are at factory firmware, please refer commit 63b8d98dd0 ("mediatek: add support for Cudy TR3000 v1")
to boot into OpenWrt initramfs (stock layout).
Flash instructions:
1. Login into the device and backup everything, especially 'Factory' part.
1. Unlock mtd partitions:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
3. Write new BL2 and FIP
mtd write openwrt-mediatek-filogic-cudy_tr3000-v1-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cudy_tr3000-v1-ubootmod-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Tested-by: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
In 2023 upstream has tightened compiler checks with this patch
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit
/scripts/Makefile.extrawarn?h=v6.15&id=0fcb70851fbfea1776ae62f67c503fef8f0292b9
A consistent function definition is now needed. I.e.
- functions must be either declared with "static" or
- functions need an additional declaration (in the header file)
Before upgrading the Realtek target to 6.12 clean the code so that the main
6.12 PR can focus on real issues from the version bump.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18925
Signed-off-by: Robert Marko <robimarko@gmail.com>
In 2023 upstream has tightened compiler checks with this patch
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit
/scripts/Makefile.extrawarn?h=v6.15&id=0fcb70851fbfea1776ae62f67c503fef8f0292b9
A consistent function definition is now needed. I.e.
- functions must be either declared with "static" or
- functions need an additional declaration (in the header file)
Before upgrading the Realtek target to 6.12 clean the code so that the main
6.12 PR can focus on real issues from the version bump.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18925
Signed-off-by: Robert Marko <robimarko@gmail.com>
In 2023 upstream has tightened compiler checks with this patch
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit
/scripts/Makefile.extrawarn?h=v6.15&id=0fcb70851fbfea1776ae62f67c503fef8f0292b9
A consistent function definition is now needed. I.e.
- functions must be either declared with "static" or
- functions need an additional declaration (in the header file)
Before upgrading the Realtek target to 6.12 clean the code so that the main
6.12 PR can focus on real issues from the version bump.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18925
Signed-off-by: Robert Marko <robimarko@gmail.com>
In 2023 upstream has tightened compiler checks with this patch
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit
/scripts/Makefile.extrawarn?h=v6.15&id=0fcb70851fbfea1776ae62f67c503fef8f0292b9
A consistent function definition is now needed. I.e.
- functions must be either declared with "static" or
- functions need an additional declaration (in the header file)
Before upgrading the Realtek target to 6.12 clean the code so that the main
6.12 PR can focus on real issues from the version bump.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18925
Signed-off-by: Robert Marko <robimarko@gmail.com>
In 2023 upstream has tightened compiler checks with this patch
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit
/scripts/Makefile.extrawarn?h=v6.15&id=0fcb70851fbfea1776ae62f67c503fef8f0292b9
A consistent function definition is now needed. I.e.
- functions must be either declared with "static" or
- functions need an additional declaration (in the header file)
Before upgrading the Realtek target to 6.12 clean the code so that the main
6.12 PR can focus on real issues from the version bump.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18925
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Nezha board has a PCF8574 that acts as an I/O expander on the
i2c2 bus. Enable the required module for it.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Instead of including the out-of-tree XR USB serial driver, use the
newly packaged in-tree driver for it.
Link: https://github.com/openwrt/openwrt/pull/18926
Signed-off-by: Robert Marko <robimarko@gmail.com>
Adapt patches adding NVMEM or fitblk rootdisk references to MMC
partitions for the changed MMC card binding.
Note that boards in 'dts' folder can only be converted once Linux 6.6,
which still depends on the old binding, has been dropped.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add patch to allow referencing MSDOS/MBR partitions in device tree to
allow legacy MT7623 boards to continue working with fitblk.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Replace downstream files by patches, either backports of those
which have already applied or pending patches tracked on patchwork.
This is done to make future maintainance more easy.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Drop patches which have been moved into target/linux/generic by commit
f4144d61d2 ("generic: 6.12: backport MediaTek Ethernet PHY changes").
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* the variant with 2.5G PHY instead of LAN SFP is called '2p5'
upstream and 'poe' in our downstream Linux 6.6 DT. Use the right
DTS depending on the kernel version and set an additional
compatible.
* drop additional DT overlay for WiFi.
The final version of the board uses a physical switch for the 12V
power of the WiFi module and the I2C EEPROM of the module always
comes empty (instead of with a MAC address).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In preparation of using the upstream mt7988a.dtsi when switching
to Linux 6.12 prepare by bringing our downstream version closer to
what went upstream.
* rename 'xphy' -> 'xsphy'
* rename 'uart[012]' -> 'serial[012]'
* only list pinctrl settings directly used in mt7988a.dtsi there,
leave it to boards to define all additional pinctrl settings
they need.
* move fan and thermal-zone to board level
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Upstream uses a different filename, so lets rename our downstream
mt7981.dtsi to mt7981b.dtsi and update the device tree of all
MT7981 boards accordingly.
This is to prepare for the switch to Linux 6.12 which is going to
use the upstream mt7981b.dtsi (plus some patches on top).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The MediaTek Ethernet PHY drivers are going to be used by multiple
targets (airoha, mediatek, ramips). Add generic backports of changes
required for recently added Ethernet PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
While it will hopefully be replaced soon by an upstream solution for
now we keep the downstream SerDes PCS implementation for MT7988A.
In order to make it work with upstream mt7988a.dtsi we have to
compensate for the changed start address of topmisc which was
moved from 0x11d10000 to 0x11d10084 to accomodate a future power
domain controller located at 0x11d10000~0x11d10080.
Hence we need to change TOP_MISC_NETSYS_PCS_MUX from 0x84 to 0x0, so
the Ethernet path/mux selection can work with upstream mt7988a.dtsi.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Upstream now uses struct ethtool_keee instead of struct ethtool_eee
as parameter to EEE-related functions. Follow that change and modify
the patch accordingly.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Commit fa0f130764 ("generic: 6.12: update block NVMEM driver") switched
to the upstream DT bindings for block partitions.
Bring back the old/legacy downstream way to assign the OF node to a
block device or partition in order to allow sharing a single DTS for
both, Linux 6.6 (which exclusively uses the old/legacy binding) and
Linux 6.12 (which will now support both, new/upstream binding and the
old/legacy binding).
Once we drop Linux 6.6 and all boards have been converted to the new
binding we can drop this patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
There are still a lot of mdio functions scattered around the code.
Move the RTL838x serdes helpers closer to the bus, add the proper
prefix and simplify the functions.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18847
Signed-off-by: Robert Marko <robimarko@gmail.com>
There is a patch/bug cascade in the realtek target phy code that must be resolved.
1. The phy_driver structure is patched to add features ONLY needed for RTL8214FC
2. The kernel is patched to allow switching fiber/copper port of phys through ethtool
by calling these new features.
3. With those patches applied the bootup always switches RTL8214FC ports to copper.
Even if a SFP module was found before and the phy driver switched to fibre before.
3. So another patch is needed that reprobes the SFP module to activate fiber again.
4. Because of the reprobing we need a fourth patch that avoid duplicate devices.
Simplify this by removing all patches and reusing the existing ethtool phy tunable
interface. The command line usage might be counterintuitive but it avoids tons of
problems in the code. In addition, this scenario is not used frequently.
Before:ethtool -s lan25 port fibre/tp
After: ethtool --set-phy-tunable lan25 downshift on/off
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18816
Signed-off-by: Robert Marko <robimarko@gmail.com>
We have modified the kernel to setup all "default" consoles,
including serial ports and framebuffers/screens, providing
no console= argument is supplied on the kernel command line.
Adding 'console=tty1' caused the 'default' serial port on
device tree systems to break, as the kernel would not carry
over the settings (like baud rate) from the bootloader.
The system administrator can still force the use of a
specific console by adding their own console= arguments.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Fixes: c099523d66 ("armsr: use console=tty1 to make
console more readily available")
Link: https://github.com/openwrt/openwrt/pull/17012
Signed-off-by: Robert Marko <robimarko@gmail.com>
A previous change added 'console=tty1' to the default kernel command
line on armsr, in order to ensure the framebuffer console is enabled
on systems capable of graphics output.
Unfortunately, this change broke boards that used device tree
(DT) firmware with serial consoles, as the serial console
specified by the system firmware (stdout-path) was no longer
setup by the kernel.
A bit of probing determined that the SPCR (serial port console
direction table) on ACPI systems was preventing Linux from setting
up a default framebuffer console on these systems (which is why
console=tty1 was added).
(The affected ACPI systems are usually VMs using QEMU's
'virt' machine and EDK2 firmware. The firmware on these systems
does not remove the SPCR when a screen is present)
So to ensure all possible systems are setup correctly, we modify
the kernel so all "default" console types (serial and screen)
are setup when no console= arguments are specified on the kernel
command line.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Fixes: c099523d66 ("use console=tty1 to make console more
readily available")
Link: https://github.com/openwrt/openwrt/pull/17012
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh patches to fix the GitHub CI warning.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18912
Signed-off-by: Nick Hainke <vincent@systemli.org>
SOC: MediaTek MT7981b
RAM: 256MB DDR3
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7981b DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Interface MAC Algorithm
LAN 8C:AE:DB:2C:xx:xx label
WAN 8C:AE:DB:2C:xx:xx label +1
WLAN 2.4G 8C:AE:DB:2C:xx:xx label +2
WLAN 5G 8C:AE:DB:2C:xx:xx label +3
Installation
-------------------Install openwrt image-------------------------------:
Set a static ip on the ethernet interface of your PC. (ip address:
192.168.1.254, subnet mask:255.255.255.0) .
Download the OpenWrt uboot image
(openwrt-mediatek-filogic-snr_cpe-ax2-bl31-uboot.fip).
SSH/SCP opened by default on the stock firmware (3.0.1).
Username: Admin, default password: Admin. Check it on the bottom of
the router.
Copy uboot image using SCP (WinSCP) to /tmp dir on SNR-CPE-AX2.
Download recovery file.
openwrt-mediatek-filogic-snr_snr-cpe-ax2-initramfs-recovery.itb.
Copy the recovery image to a TFTP server reachable at 192.168.1.254/24.
Open ssh shell to the SNR-CPE-AX2.
Run commands:
mtd write \
/tmp/openwrt-mediatek-filogic-snr_snr-cpe-ax2-bl31-uboot.fip FIP
reboot
Wait until recovery boot.
Open web 192.168.1.1 and do sysupgrade by
openwrt-mediatek-filogic-snr_cpe-ax2-squashfs-sysupgrade.itb
Signed-off-by: Nikolay March <palladin82@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/18700
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Sort the config in alphabetical order
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/18897
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Upstream seems to be using led-sources instead of custom properties.
Code mostly taken from mt76.
Changed all(few) users of qca,led_pin to use the new format.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18805
Signed-off-by: Robert Marko <robimarko@gmail.com>
The MIPS CPC (Cluster Power Controller) is setup during boot and can take
its configuration from the devicetree. This is currently not possible
because the cpc probing happens before dt initialization. Call order
during startup is:
setup_arch()
prom_init() <- our function
mips_cpc_probe()
smp_stuff()
arch_mem_init()
device_tree_init() <- our function
unflatten_and_copy_device_tree()
To avoid ugly hacking and support a clean devicetree relocate the cps/smp
stuff to device_tree_init(). This is basically the same location as in
generic mips initialization.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Link: https://github.com/openwrt/openwrt/pull/18888
Signed-off-by: Robert Marko <robimarko@gmail.com>
Make it easier to upgrade the kernel in the future. For this remove
the 320-harden-fw_init_cmdline.patch and add the logic into the
startup sequence at the right place.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18853
Signed-off-by: Robert Marko <robimarko@gmail.com>
The 6.12 testing kernel for ath79 target is ready now.
Tested on AR9344 (ath79/nand) and QCA9531 (ath79/generic).
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
All kernel symbols are automatically refreshed by
`make kernel_oldconfig CONFIG_TARGET=target` and
`make kernel_oldconfig CONFIG_TARGET=subtarget`.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
This is a preparation for 6.12 kernel support. It can help us
track the files history by using the Git tool.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Manually move the common NVMEM Kconfig symbols to the shared
config file and disable them for the mikrotik subtarget. Other
changes are automatically completed by `make kernel_oldconfig`.
This is a preparation for introducing the 6.12 kernel support.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
RTL931x devices are dual core with two threads each. That is a total
of 4 VPEs (CPUs) in the kernel. Adapt the kernel config for that.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Link: https://github.com/openwrt/openwrt/pull/18889
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use upstreamed v6.16 patches for IPQ5018 tsens support.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18884
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use upstreamed v6.16 patch for IPQ5018 TCSR support and setting the
download mode.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18884
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use upstreamed patches for IPQ5018 PCIe support, including patches for
phy and controller drivers and dts nodes.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18884
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Since the early beginning of the Realtek DSA driver there is an uncovered
locking issue between the standard (parent) mdio bus and the DSA (child)
mdio bus. This comes from the fact that the DSA bus simply links to the
parent read and write functions and calls them directly. This leads to
the following lock issue.
- Child bus calls phy_read/write functions and uses its internal lock
- Parent bus calls phy_read/write functions and uses its internal lock
It becomes clear that critical section can be accessed twice without
knowing that a operation from the other bus is currently active. This
can lead to critical malfunctions because the mdio driver needs a lot of
internal magic to get page selection done right. Effects are:
- The original page is lost after a phy_write/read_paged() call
- dmesg like "Realtek RTL8218B (external) rtl838x slave mii-0:00:
Expected external RTL8218B, found PHY-ID 6b23"
Other DSA drivers simply use the read/write functions from the parent bus
and thus avoid locking issues. Do it the same way.
Fixes: 2b88563ee5 ("realtek: update the tree to the latest refactored version")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18824
Signed-off-by: Robert Marko <robimarko@gmail.com>
Before generating the factory image, check if the input file
exists. Fix the build error when sysupgrade image is too big:
[mkwrgimg] *** error: stat failed on /builder/shared-workdir/build/build_dir/target-mipsel_24kc_musl/linux-ramips_rt288x/tmp/openwrt-ramips-rt288x-airlink101_ar670w-squashfs-factory.bin, No such file or directory
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18836
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This was needed while ar71xx was in tree. This is no longer the case.
Not only that, these have already been converted to OF.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18860
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
There are currently two power functions for the RTL8214FC in the driver
- rtl8380_rtl8214fc_on_off(): powers on/off both ports
- rtl8214fc_power_set(): powers on/off fibre or copper individually
While it seems obvious to merge these, one of them uses extended register
29 and the other register 30 to achieve the update. From looking at the
GPL source drops both methods exist with exactly the same operations. So
where to go from here? The descision was made based on:
- register 30 is only used during patching, 29 during normal operation
- Avoid raw page if possible to use function for RTL839x
So the attached patch was created. The result in the power down bits
was compared for the two old and the new implementation. Result is
always the same.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18707
Signed-off-by: Robert Marko <robimarko@gmail.com>
RTL9311 switches (like the Linksys LGS352C) will boot but have not set
the right family id in the soc_info structure. Fix that so drivers do
their work right when checking for that.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18871
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RPi upstream repo switched to the upstream SDHOST driver some time ago, so
it's time to do the same in our configs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Cleanup the code of the RTL83xx packet receive interrupt handler. Not
only for better readability but to avoid inconsistencies and stalls on
the RTL839x targets.
The current implementation seems to come from the GPL source code.
Calling the existing cleanup() function inside the interrupt context
without any locks conflicts with SMP & NAPI polling and makes things
worse instead of giving any benefit. Simply ignore RX buffer overruns
and let the device handle packet dropping itself.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18855
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Import pending PXA I2C recovery fixes so that if I2C recovery is enabled in
the DTS it does not completely break I2C as it currently does since kernel
6.6.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Use the "1/1" as a iteration count of hexdump expression instead of the
broken "1", to fix the issue that the invalid bootnum will be obtained.
Currently, the hexdump command always outputs "0" when the decimal format
and the iteration count "1" are specified[0]. This is unexpected
behaviour, but the cause is unknown and use this fix as a workaround.
[0]: https://github.com/openwrt/openwrt/issues/18808
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18827
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop configs, files and patches for Linux 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18848
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch to Linux kernel version 6.12.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18848
Signed-off-by: Robert Marko <robimarko@gmail.com>
Default qualcommax target to 6.12 kernel.
It makes no sense for us to double the effort required for backporting
upstreamed patches or for downstream modifications.
Link: https://github.com/openwrt/openwrt/pull/18840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Based on other mt7622 dts, it is not difficult to infer that the
missing interrupt controller is "pio". Fix dtc warning:
mt7622.dtsi:282.3-26: Warning (interrupts_property): /ethernet@1b100000/mdio-bus/ethernet-phy@7:#interrupt-cells: size is (8), expected multiple of 12
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Add missing #address-cells, #size-cells and #sound-dai-cells to
fix the following dtc warnings:
mt7986a-bananapi-bpi-r3-respeaker-2mics.dtso:46.5-18: Warning (reg_format): /fragment@1/__overlay__/wm8960@1a:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
mt7986a-bananapi-bpi-r3-respeaker-2mics.dtso:29.11-31.7: Warning (sound_dai_property): /fragment@0/__overlay__/sound_wm8960/codec: Missing property '#sound-dai-cells' in node /fragment@1/__overlay__/wm8960@1a or bad phandle (referred from sound-dai[0])
mt7986a-rfb-spim-nand.dts:17.12-19.5: Warning (sound_dai_property): /sound_wm8960/platform: Missing property '#sound-dai-cells' in node /soc/audio-controller@11210000 or bad phandle (referred from sound-dai[0])
mt7986a-rfb-spim-nand.dts:21.9-23.5: Warning (sound_dai_property): /sound_wm8960/codec: Missing property '#sound-dai-cells' in node /soc/i2c@11008000/wm8960@1a or bad phandle (referred from sound-dai[0])
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
