Difuse/difos
2
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity Actions

qualcommax: add support for I-O DATA WN-DAX3000GR

Browse source 
I-O DATA WN-DAX3000GR is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based
on IPQ5018.

Specification:

- SoC             : Qualcomm IPQ5018
- RAM             : DDR3 512 MiB
- Flash           : SPI-NAND 128 MiB (Macronix MX35UF1G24AD-Z4I)
- WLAN            : 2.4/5 GHz 2T2R
  - 2.4 GHz       : Qualcomm IPQ5018 (SoC)
  - 5 GHz         : Qualcomm Atheros QCN6102
- Ethernet        : 5x 10/100/1000 Mbps
  - wan (phy)     : Qualcomm IPQ5018 (SoC)
  - lan (switch)  : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO): 7x/5x
- UART            : through-hole on PCB (J3)
  - assignment    : 3.3V, TX, RX, NC, GND from tri-angle marking
  - settings      : 115200n8
- USB             : USB 2.0 Type-A (through-hole on PCB, "J6")
- Power           : 12 VDC, 1A (Typ. 930 mA)

Flash instruction using factory.bin image:

1. Boot WN-DAX3000GR with router mode
2. Access to the WebUI ("http://192.168.0.1/") on the device and open
   the firmware update page ("ファームウェア")
3. Select the OpenWrt factory.bin image and click update ("更新") button
4. Wait ~120 seconds to complete flashing

Switching to the stock firmware:

1. Load the elecom.sh script

   . /lib/upgrade/elecom.sh

2. Check the current index of rootfs

   bootconfig_rw_index 0:bootconfig rootfs

3. Set the index to inverted value

   bootconfig_rw_index 0:bootconfig rootfs <value>
   bootconfig_rw_index 0:bootconfig1 rootfs <value>

   example:

   - step2 returned "0":

     bootconfig_rw_index 0:bootconfig rootfs 1
     bootconfig_rw_index 0:bootconfig1 rootfs 1

   - step2 returned "1":

     bootconfig_rw_index 0:bootconfig rootfs 0
     bootconfig_rw_index 0:bootconfig1 rootfs 0

4. Reboot

Partition Layout (Stock FW, bootconfig(rootfs)=1):

0x000000000000-0x000000080000 : "0:SBL1"
0x000000080000-0x000000100000 : "0:MIBIB"
0x000000100000-0x000000140000 : "0:BOOTCONFIG"
0x000000140000-0x000000180000 : "0:BOOTCONFIG1"
0x000000180000-0x000000280000 : "0:QSEE"
0x000000280000-0x000000380000 : "0:QSEE_1"
0x000000380000-0x0000003c0000 : "0:DEVCFG"
0x0000003c0000-0x000000400000 : "0:DEVCFG_1"
0x000000400000-0x000000440000 : "0:CDT"
0x000000440000-0x000000480000 : "0:CDT_1"
0x000000480000-0x000000500000 : "0:APPSBLENV"
0x000000500000-0x000000640000 : "0:APPSBL"
0x000000640000-0x000000780000 : "0:APPSBL_1"
0x000000780000-0x000000880000 : "0:ART"
0x000000880000-0x000000900000 : "0:TRAINING"
0x000000900000-0x000003c40000 : "rootfs_1"
0x000003c40000-0x000003fc0000 : "Config"
0x000003fc0000-0x000007300000 : "rootfs"
0x000007300000-0x000007680000 : "Config_2"
0x000007680000-0x000007700000 : "idmkey"
0x000007700000-0x000007c00000 : "Reserved"
0x000007c00000-0x000007c80000 : "FWHEADER"
0x000007c80000-0x000007d00000 : "Factory"

Known Issues:

- This device has a Macronix MX35UF1G24AD SPI-NAND chip registered as
  oobsize=128 in Linux Kernel. But using BCH8 breaks I/O on the chip
  with the following errors, so this support uses BCH4 instead.

  [    1.542261] 0x000000480000-0x000000500000 : "0:appsblenv"
  [    1.547959] 1 fixed-partitions partitions found on MTD device 0:appsblenv
  [    1.551265] Creating 1 MTD partitions on "0:appsblenv":
  [    1.558096] 0x000000000000-0x000000040000 : "env-data"
  [    1.627282] u-boot-env-layout 79b0000.qpic-nand:flash@0:partitions:partition-0-appsblenv:partition@0:nvmem-layout: probe with driver u-boot-env-layout failed with error -74

  root@OpenWrt:~# strings /dev/mtdblock10
  [   77.806720] mtdblock: MTD device '0:appsblenv' is NAND, please consider using UBI block devices instead.
  [   77.807554] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0
  [   77.815977] I/O error, dev mtdblock10, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0
  [   77.824721] I/O error, dev mtdblock10, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 0
  [   77.834095] I/O error, dev mtdblock10, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
  [   77.843278] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
  [   77.851577] Buffer I/O error on dev mtdblock10, logical block 0, async page read

Notes:

- This device has dual-boot feature and it's managed by the index in the
  0:bootconfig and 0:bootconfig1 partitions.

- There are through-holes on PCB for USB 2.0, but it cannot be accessed
  without disassembly of the housing. So it's not enabled in this
  support.

- WN-DAX3000GR has the "bt_fw" volume in the firmware UBI in addition to
  the volumes that will be removed in the section of ELECOM WRC-X3000GS2
  in /lib/upgrade/platform.sh.
  That volume is unnecessary for OpenWrt and add
  `remove_oem_ubi_volume bt_fw` to remove that volume when sysupgrade.
  (that function doesn't anything without errors if no specified volume)

MAC Addresses:

LAN    : 50:41:B9:xx:xx:64 (0:APPSBLENV, "ethaddr"/"eth1addr" (text))
WAN    : 50:41:B9:xx:xx:66 (0:APPSBLENV, "eth0addr" (text))
2.4 GHz: 50:41:B9:xx:xx:64 (0:APPSBLENV, "wifi0"    (text))
5 GHz  : 50:41:B9:xx:xx:65 (0:APPSBLENV, "wifi1"    (text))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19053
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit is contained in:
INAGAKI Hiroshi 2025-06-04 00:08:06 +09:00 committed by Robert Marko
parent 2186f4aa75
commit 0cbdab5038
7 changed files with 533 additions and 5 deletions
Show stats Download patch file Download diff file Expand all files Collapse all files

2
package/firmware/ipq-wifi/Makefile
View file

@ -43,6 +43,7 @@ ALLWIFIBOARDS:= \
glinet_gl-ax1800 \
glinet_gl-axt1800 \
glinet_gl-b3000 \
iodata_wn-dax3000gr \
linksys_homewrk \
linksys_mr5500 \
linksys_mr7350 \
@ -198,6 +199,7 @@ $(eval $(call generate-ipq-wifi-package,elecom_wrc-x3000gs2,ELECOM WRC-X3000GS2)
$(eval $(call generate-ipq-wifi-package,glinet_gl-ax1800,GL.iNet GL-AX1800))
$(eval $(call generate-ipq-wifi-package,glinet_gl-axt1800,GL.iNet GL-AXT1800))
$(eval $(call generate-ipq-wifi-package,glinet_gl-b3000,GL.iNet GL-B3000))
$(eval $(call generate-ipq-wifi-package,iodata_wn-dax3000gr,I-O DATA WN-DAX3000GR))
$(eval $(call generate-ipq-wifi-package,linksys_homewrk,Linksys HomeWRK))
$(eval $(call generate-ipq-wifi-package,linksys_mr5500,Linksys MR5500))
$(eval $(call generate-ipq-wifi-package,linksys_mr7350,Linksys MR7350))

502
target/linux/qualcommax/files/arch/arm64/boot/dts/qcom/ipq5018-wn-dax3000gr.dts Normal file
View file

@ -0,0 +1,502 @@
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
/dts-v1/;
#include "ipq5018.dtsi"
#include "ipq5018-ess.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
/ {
model = "I-O DATA WN-DAX3000GR";
compatible = "iodata,wn-dax3000gr", "qcom,ipq5018";
aliases {
serial0 = &blsp1_uart1;
led-boot = &led_status_green;
led-failsafe = &led_status_red;
led-upgrade = &led_status_green;
label-mac-device = <&dp1>;
};
chosen {
bootargs-append = " root=/dev/ubiblock0_1 coherent_pool=2M";
stdout-path = "serial0:115200n8";
};
keys {
compatible = "gpio-keys";
pinctrl-0 = <&button_pins>;
pinctrl-names = "default";
button-reset {
label = "reset";
gpios = <&tlmm 22 GPIO_ACTIVE_LOW>;
linux,code = <KEY_RESTART>;
};
switch-led-on {
label = "led-on";
gpios = <&tlmm 23 GPIO_ACTIVE_LOW>;
linux,code = <BTN_0>;
linux,input-type = <EV_SW>;
};
switch-repeater {
label = "repeater";
gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
linux,code = <BTN_1>;
linux,input-type = <EV_SW>;
};
switch-ap {
label = "ap";
gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
linux,code = <BTN_2>;
linux,input-type = <EV_SW>;
};
button-wps {
label = "wps";
gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WPS_BUTTON>;
};
};
leds {
compatible = "gpio-leds";
pinctrl-0 = <&led_pins>;
pinctrl-names = "default";
led-0 {
gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_WPS;
};
led_status_green: led-1 {
gpios = <&tlmm 13 GPIO_ACTIVE_HIGH>;
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_STATUS;
};
led_status_red: led-2 {
gpios = <&tlmm 16 GPIO_ACTIVE_HIGH>;
color = <LED_COLOR_ID_ORANGE>;
function = LED_FUNCTION_STATUS;
};
led-3 {
gpios = <&tlmm 24 GPIO_ACTIVE_HIGH>;
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_WAN_ONLINE;
};
led-4 {
gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>;
color = <LED_COLOR_ID_GREEN>;
function = "router";
};
led-5 {
gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>;
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_POWER;
default-state = "on";
};
led-6 {
gpios = <&tlmm 28 GPIO_ACTIVE_HIGH>;
color = <LED_COLOR_ID_GREEN>;
function = LED_FUNCTION_WAN;
};
};
reserved-memory {
q6_mem_regions: q6_mem_regions@4b000000 {
no-map;
reg = <0x0 0x4b000000 0x0 0x3000000>;
};
};
};
&sleep_clk {
clock-frequency = <32000>;
};
&xo_board_clk {
clock-frequency = <24000000>;
};
&blsp1_uart1 {
status = "okay";
pinctrl-0 = <&serial_0_pins>;
pinctrl-names = "default";
};
&crypto {
status = "okay";
};
&cryptobam {
status = "okay";
};
&prng {
status = "okay";
};
&qfprom {
status = "okay";
};
&qpic_bam {
status = "okay";
};
&qpic_nand {
pinctrl-0 = <&qpic_pins>;
pinctrl-names = "default";
status = "okay";
flash@0 {
compatible = "spi-nand";
reg = <0>;
#address-cells = <1>;
#size-cells = <1>;
nand-ecc-engine = <&qpic_nand>;
/* strength=8 breaks NAND I/O, use 4 instead */
nand-ecc-strength = <4>;
nand-ecc-step-size = <512>;
nand-bus-width = <8>;
partitions {
compatible = "qcom,smem-part";
partition-0-appsblenv {
compatible = "fixed-partitions";
label = "0:appsblenv";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "env-data";
reg = <0x0 0x40000>;
nvmem-layout {
compatible = "u-boot,env";
macaddr_appsblenv_ethaddr: ethaddr {
compatible = "mac-base";
#nvmem-cell-cells = <1>;
};
};
};
};
};
};
};
&switch {
status = "okay";
switch_mac_mode = <MAC_MODE_SGMII_CHANNEL0>;
qcom,port_phyinfo {
port@0 {
port_id = <1>;
mdiobus = <&mdio0>;
phy_address = <7>;
};
port@1 {
port_id = <2>;
forced-speed = <1000>;
forced-duplex = <1>;
};
};
};
&dp1 {
status = "okay";
label = "wan";
nvmem-cells = <&macaddr_appsblenv_ethaddr 2>;
nvmem-cell-names = "mac-address";
};
&dp2 {
status = "okay";
nvmem-cells = <&macaddr_appsblenv_ethaddr 0>;
nvmem-cell-names = "mac-address";
fixed-link {
speed = <1000>;
full-duplex;
};
};
&mdio0 {
status = "okay";
};
&mdio1 {
status = "okay";
pinctrl-0 = <&mdio1_pins>, <&switch_reset_pins>;
pinctrl-names = "default";
reset-gpios = <&tlmm 39 GPIO_ACTIVE_LOW>;
qca8337_0: ethernet-phy@0 {
reg = <0>;
};
qca8337_1: ethernet-phy@1 {
reg = <1>;
};
qca8337_2: ethernet-phy@2 {
reg = <2>;
};
qca8337_3: ethernet-phy@3 {
reg = <3>;
};
ethernet-switch@18 {
compatible = "qca,qca8337";
reg = <0x18>;
#address-cells = <1>;
#size-cells = <0>;
ports {
#address-cells = <1>;
#size-cells = <0>;
port@1 {
reg = <1>;
label = "lan1";
phy-handle = <&qca8337_0>;
};
port@2 {
reg = <2>;
label = "lan2";
phy-handle = <&qca8337_1>;
};
port@3 {
reg = <3>;
label = "lan3";
phy-handle = <&qca8337_2>;
};
port@4 {
reg = <4>;
label = "lan4";
phy-handle = <&qca8337_3>;
};
port@6 {
reg = <6>;
phy-mode = "sgmii";
ethernet = <&dp2>;
qca,sgmii-enable-pll;
fixed-link {
speed = <1000>;
full-duplex;
};
};
};
};
};
&tlmm {
button_pins: button-state {
key-pullup-pins {
pins = "gpio22", "gpio23", "gpio38";
function = "gpio";
drive-strength = <8>;
bias-pull-up;
};
key-pulldown-pins {
pins = "gpio31", "gpio32";
function = "gpio";
drive-strength = <8>;
bias-pull-down;
};
};
led_pins: led-state {
pins = "gpio12", "gpio13", "gpio16", "gpio24",
"gpio25", "gpio26", "gpio28";
function = "gpio";
drive-strength = <8>;
bias-pull-down;
};
mdio1_pins: mdio-state {
mdc-pins {
pins = "gpio36";
function = "mdc";
drive-strength = <8>;
bias-pull-up;
};
mdio-pins {
pins = "gpio37";
function = "mdio";
drive-strength = <8>;
bias-pull-up;
};
};
qpic_pins: qpic-state {
clock-pins {
pins = "gpio9";
function = "qspi_clk";
drive-strength = <8>;
bias-disable;
};
cs-pins {
pins = "gpio8";
function = "qspi_cs";
drive-strength = <8>;
bias-disable;
};
data-pins {
pins = "gpio4", "gpio5", "gpio6", "gpio7";
function = "qspi_data";
drive-strength = <8>;
bias-disable;
};
};
serial_0_pins: uart0-state {
pins = "gpio20", "gpio21";
function = "blsp0_uart0";
bias-disable;
};
switch_reset_pins: switch-reset-state {
pins = "gpio39";
function = "gpio";
drive-strength = <8>;
bias-pull-down;
};
};
&tsens {
status = "okay";
};
&q6v5_wcss {
status = "okay";
memory-region = <&q6_mem_regions>;
firmware-name = "ath11k/IPQ5018/hw1.0/q6_fw.mdt",
"ath11k/IPQ5018/hw1.0/m3_fw.mdt",
"ath11k/QCN6122/hw1.0/m3_fw.mdt";
boot-args = <0x2 4 2 18 0 0>; /* pcie:1, len:4, updid:2, reset:gpio18 */
q6_wcss_pd1: pd-1 {
firmware-name = "ath11k/IPQ5018/hw1.0/q6_fw.mdt";
resets =
<&gcc GCC_WCSSAON_RESET>,
<&gcc GCC_WCSS_BCR>,
<&gcc GCC_CE_BCR>;
reset-names =
"wcss_aon_reset",
"wcss_reset",
"ce_reset";
clocks =
<&gcc GCC_WCSS_AHB_S_CLK>,
<&gcc GCC_WCSS_ACMT_CLK>,
<&gcc GCC_WCSS_AXI_M_CLK>;
clock-names =
"gcc_wcss_ahb_s_clk",
"gcc_wcss_acmt_clk",
"gcc_wcss_axi_m_clk";
interrupts-extended =
<&wcss_smp2p_in 8 IRQ_TYPE_NONE>,
<&wcss_smp2p_in 9 IRQ_TYPE_NONE>,
<&wcss_smp2p_in 12 IRQ_TYPE_NONE>,
<&wcss_smp2p_in 11 IRQ_TYPE_NONE>;
interrupt-names =
"fatal",
"ready",
"spawn-ack",
"stop-ack";
qcom,smem-states =
<&wcss_smp2p_out 8>,
<&wcss_smp2p_out 9>,
<&wcss_smp2p_out 10>;
qcom,smem-state-names =
"shutdown",
"stop",
"spawn";
};
q6_wcss_pd2: pd-2 {
firmware-name = "ath11k/IPQ5018/hw1.0/q6_fw.mdt";
interrupts-extended =
<&wcss_smp2p_in 16 IRQ_TYPE_NONE>,
<&wcss_smp2p_in 17 IRQ_TYPE_NONE>,
<&wcss_smp2p_in 20 IRQ_TYPE_NONE>,
<&wcss_smp2p_in 19 IRQ_TYPE_NONE>;
interrupt-names =
"fatal",
"ready",
"spawn-ack",
"stop-ack";
qcom,smem-states =
<&wcss_smp2p_out 16>,
<&wcss_smp2p_out 17>,
<&wcss_smp2p_out 18>;
qcom,smem-state-names =
"shutdown",
"stop",
"spawn";
};
};
&wifi0 {
status = "okay";
qcom,rproc = <&q6_wcss_pd1>;
qcom,ath11k-calibration-variant = "IODATA-WN-DAX3000GR";
qcom,ath11k-fw-memory-mode = <2>;
qcom,bdf-addr = <0x4c400000>;
ieee80211-freq-limit = <2400000 2483000>;
};
&wifi1 {
status = "okay";
qcom,rproc = <&q6_wcss_pd2>;
qcom,userpd-subsys-name = "q6v5_wcss_userpd2";
qcom,ath11k-calibration-variant = "IODATA-WN-DAX3000GR";
qcom,ath11k-fw-memory-mode = <2>;
qcom,bdf-addr = <0x4d100000>;
qcom,m3-dump-addr = <0x4df00000>;
ieee80211-freq-limit = <5150000 5730000>;
};

18
target/linux/qualcommax/image/ipq50xx.mk
View file

@ -57,6 +57,24 @@ define Device/glinet_gl-b3000
endef
TARGET_DEVICES += glinet_gl-b3000
define Device/iodata_wn-dax3000gr
$(call Device/FitImageLzma)
DEVICE_VENDOR := I-O DATA
DEVICE_MODEL := WN-DAX3000GR
DEVICE_DTS_CONFIG := config@mp03.3
SOC := ipq5018
KERNEL_IN_UBI := 1
BLOCKSIZE := 128k
PAGESIZE := 2048
IMAGE_SIZE := 52480k
NAND_SIZE := 128m
IMAGES += factory.bin
IMAGE/factory.bin := append-ubi | qsdk-ipq-factory-nand | \
mstc-header 4.04(XZH.1)b90 0x480
DEVICE_PACKAGES := ath11k-firmware-qcn6122 ipq-wifi-iodata_wn-dax3000gr
endef
TARGET_DEVICES += iodata_wn-dax3000gr
define Device/linksys_ipq50xx_mx_base
$(call Device/FitImageLzma)
DEVICE_VENDOR := Linksys

3
target/linux/qualcommax/ipq50xx/base-files/etc/board.d/01_leds
View file

@ -9,7 +9,8 @@ board_config_update
board=$(board_name)
case "$board" in
elecom,wrc-x3000gs2)
elecom,wrc-x3000gs2|\
iodata,wn-dax3000gr)
ucidef_set_led_netdev "wan" "WAN" "green:wan" "wan" "tx rx link_10 link_100 link_1000"
;;
linksys,mr5500)

1
target/linux/qualcommax/ipq50xx/base-files/etc/board.d/02_network
View file

@ -8,6 +8,7 @@ ipq50xx_setup_interfaces()
local board="$1"
case $board in
elecom,wrc-x3000gs2|\
iodata,wn-dax3000gr|\
linksys,mr5500)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
;;

6
target/linux/qualcommax/ipq50xx/base-files/etc/hotplug.d/firmware/11-ath11k-caldata
View file

@ -9,7 +9,8 @@ board=$(board_name)
case "$FIRMWARE" in
"ath11k/IPQ5018/hw1.0/cal-ahb-c000000.wifi.bin")
case "$board" in
elecom,wrc-x3000gs2)
elecom,wrc-x3000gs2|\
iodata,wn-dax3000gr)
caldata_extract "0:art" 0x1000 0x20000
wlan_mac=$(mtd_get_mac_ascii 0:appsblenv wifi0)
ath11k_patch_mac $wlan_mac 0
@ -34,7 +35,8 @@ case "$FIRMWARE" in
;;
"ath11k/QCN6122/hw1.0/cal-ahb-b00a040.wifi1.bin")
case "$board" in
elecom,wrc-x3000gs2)
elecom,wrc-x3000gs2|\
iodata,wn-dax3000gr)
caldata_extract "0:art" 0x26800 0x20000
wlan_mac=$(mtd_get_mac_ascii 0:appsblenv wifi1)
ath11k_patch_mac $wlan_mac 0

6
target/linux/qualcommax/ipq50xx/base-files/lib/upgrade/platform.sh
View file

@ -71,8 +71,9 @@ platform_check_image() {
platform_do_upgrade() {
case "$(board_name)" in
elecom,wrc-x3000gs2)
local delay index
elecom,wrc-x3000gs2|\
iodata,wn-dax3000gr)
local delay
delay=$(fw_printenv bootdelay)
[ -z "$delay" ] || [ "$delay" -eq "0" ] && \
@ -80,6 +81,7 @@ platform_do_upgrade() {
elecom_upgrade_prepare
remove_oem_ubi_volume bt_fw
remove_oem_ubi_volume ubi_rootfs
remove_oem_ubi_volume wifi_fw
nand_do_upgrade "$1"