Specifications:
SoC: MediaTek MT7981B
RAM: 1024MiB
Flash: SPI-NAND 128 MiB
Switch: 1 WAN, 4 LAN (Gigabit)
USB: two M.2 slots for 5G modems via USB 3.0 hub, external USB 3.0 port
Buttons: Reset, Mesh
Power: DC 12V 1A
WiFi: MT7976CN
UART: 115200n8
UART Layout:
VCC-RX-TX-GND
Installation:
1. Power down the router and hold in the Reset button.
2. While holding in the button power up the router again.
3. Hold the button in for 10 seconds and then release.
4. Use your browser to go to 192.168.1.1
5. If you see a GUI that is for flashing firmware then you have the V2 model.
If there is no GUI and the router continues to boot up normally
you have the V1 model.
6. Now use the V2 sysugrade file.
Note: Recovery GUI it can be used to recover from an incorrect firmware flash.
Based on patches adding support for this device by Yannick Chabanois (openmptcprouter)
and Dairyman (ofmodemsandmen)
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18514
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The High-Speed SD mode stability issue should have been fixed.
Increase the MMC max-frequency to improve the IO speed. We can
still use the sysfs to limit the clock frequency, e.g.
root@OpenWrt:~# echo 25000000 > /sys/kernel/debug/mmc0/clock
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18896
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This new feature has some improvements for random RW performance.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18896
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The MT7628 programing guide shows that the correct DTOC unit is
1048576 clocks instead of 65536 clocks. This value is also used
by linux upstream mtk-sd driver. Correct the DTOC register and
also round up its value.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18896
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
SoC: MediaTek MT7628NN
RAM: 128 MB, EtronTech EM68C16CWQG-25H (DDR2)
Flash: 32MB, Winbond 25Q256JVFQ (Dual Boot, SPI)
Switch: MediaTek MT7628AN, 4 ports 100 Mbps
WiFi: MediaTek MT7603 2T2R/2.4GHz 802.11n
GPIO: 2 buttons (Wi-Fi, Reset), 3 LEDs (Power, Internet, Wi-Fi), 1 mode switch
Disassembly:
At the bottom, under the LEDs, there are 2 screws hidden by rubber feet. After removing the screws, pry the gray plastic part around (it is secured with latches) and remove it.
Serial Interface:
The serial interface can be connected to the 5 pin dots located on the right between the operating mode switch and the antenna.
Pins (from antenna to operating mode switch):
VCC
TX
RX
NC
GND
Settings: 115200, 8N1
Flashing via OEM recovery software:
1. Download the OEM recovery software from the manufacturer's website
2. Download the firmware image (for OpenWRT it is *-squashfs-factory.bin), rename it to KN-1112_recovery.bin
3. Replace the file in the fw folder OEM recovery software with the file from step 2.
4. Run the OEM recovery software and follow the instructions.
Flashing via TFTP:
1. Connect your PC and router to port 1-3, configure PC interface using IP 192.168.1.2, mask 255.255.255.252
2. Serve the firmware image (for OpenWRT it is *-squashfs-factory.bin) renamed to KN-1112_recovery.bin via TFTP
3. Power up the router while pressing Reset button on the back
4. Release Restart button when Power LED starts blinking
To revert back to OEM firmware:
The return to the OEM firmware is carried out by using the methods described above with the help of the appropriate firmware image.
When using OEM bootloader, the firmware image size cannot exceed the size of one OEM «Firmware_x» partition or Kernel + rootFS size.
Signed-off-by: Anton Yu. Ivanusev <ivanusevanton@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/19091
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Zyxel XGS1210-12 Switch is a 10 + 2 port multi-GBit switch with
8 x 1000BaseT, 2 x 10/100/1000/2500BaseT Ethernet ports and
2 SFP+ module slot.
Hardware:
- RTL9302B SoC
- Macronix MX25L12833F (16MB flash)
- Nanja NT5CC64M16GP-1 (128MB DDR3 SDRAM)
- RTL8231 GPIO extender to control the port LEDs
- RTL8218D 8x Gigabit PHY
- RTL8226 2x 10m/100m/1/2.5 Gigabit PHY
- SFP+ 2x 10GBit slot
Power is supplied via a 12V 1.5A standard barrel connector. At the
right side behind the grid is UART serial connector. A Serial
header can be connected to from the outside of the switch trough
the airvents with a standard 2.54mm header.
Pins are from top to bottom Vcc(3.3V), TX, RX and GND. Serial
connection is via 115200 baud, 8N1.
A reset button is accessble through a hole in the front panel
At the time of this commit, all ethernet ports work under OpenWrt,
including the various NBaseT modes, SFP+ slots are supported with i2c bus.
Installation
--------------
* Connect serial as per the layout above. Connection parameters: 115200 8N1.
* Navigate to 'Management' in the OEM web interface and click on 'Firmware upgrade'
to the left.
* Upload the OpenWrt initramfs image, and wait till the switch reboots.
* Connect to the device through serial and change the U-boot boot command.
> fw_setenv bootcmd 'rtk network on; boota'
* Reboot, scp the sysupgrade image to /tmp, verify the checksum and flash it:
> sysupgrade openwrt-realtek-rtl930x-Zyxel_xgs1210-12-squashfs-sysupgrade.bin
* Upon reboot, you have a functional OpenWrt installation. Leave the bootcmd
value as is - without 'rtk network on' the switch will fail to initialise
the network.
Debug
------------
* Connect serial as per the layout above. Connection parameters: 115200 8N1.
* A tftp server is requiered, tftpd-hpa works well.
* Power the device, at U-Boot start rapidly hit Esc key to stop autoboot
* Enable network:
> rtk network on
* Change ip address (default is 192.168.1.1):
> setenv ipaddr 192.168.1.6
* Download initramfs:
> tftpboot 0x84f00000 192.168.1.111:openwrt-realtek-rtl930x-Zyxel_xgs1210-12-initramfs-kernel.bin
* Boot loaded file:
> bootm 0x84f00000
This prodecudre also apply to the sock firmware with the file XGS1210-12_V2.00(ABTY.1)C0.bix.
More information can be found on the page of XGS1250-12 as they share the same base.
Signed-off-by: Nicolas BERTRAND <nicolasbertrand89@gmail.com>
[fixed white space error]
Signed-off-by: Paul Spooren <mail@aparcar.org>
The TP-Link TL-ST1008F is an 8-port multi-gig switch with 8x SFP+ ports
which support 1G/2.5G/10G speeds. Out of the box it is an unmanaged
switch but with RTL9303 and sufficient RAM + Flash it easily can run as
a managed Linux switch.
Hardware:
- Realtek RTL9303 Switch SoC
- Winbond 25Q256JVFQ (32MB flash)
- Samsung K4B4G1646E-BYMA (512MB DDR3 SDRAM)
- TCA9534 GPIO extender to control the port LEDs
- 8x SFP+ 1/2.5/10G slot
- Serial: 3V3 logic, 115200 8N1
- 5-pin JTAG
- physical tri-state switch (used by stock firmware for port speed
config)
- 24-LED port speed matrix
- robust full-metal case
Power is supplied via a 12V 2A standard barrel connector.
There are THT holes on the PCB for serial console next to the flash chip
and JTAG pads. Serial uses 3V3 logic and standard 115200-8N1 config.
Pinout is labeled on the PCB.
All ports/connectors and LEDs are on the back, only Power LED is on the
front.
Hints before flashing
----------------------
* It is recommended to backup the stock flash contents before proceeding.
Backup can be done from U-Boot (with memory display), from OpenWrt
initramfs or probably with SPI flash programmer.
There is no stock recovery functionality.
* Use a small image for RAM boot or first flash. Since you need to use
ymodem, this is really slow and takes time.
* This does not keep the dual-partition layout for firmware to have more
space available for a single OpenWrt installation.
Initial flashing
----------------------
The stock U-boot has broken networking thus no TFTP available. Serial
transfer only.
1. Open device and connect serial as per layout and settings
(recommended to use picocom, ymodem not working with minicom)
2. Connect power to device and press Esc when prompted to enter
the U-Boot console.
3. Boot initramfs
* in the U-Boot console:
loady 0x82000000 (load OpenWrt image via ymodem)
CTRL-A CTRL-S <initramfs.bin> (specify initramfs image for
picocom to upload)
bootm 0x82000000 (boot initramfs from RAM)
(Just to be on the safe side, backup your flash now while RAM-booted)
4. Connect network to your device
5. Upload the sysupgrade image (e.g. with scp)
6. Do sysupgrade
There's no need to adjust the bootcmd in U-Boot. Networking is running
fine once the realtek driver initialized everything in OpenWrt. No
functional difference with running 'rtk network on' within U-Boot
before. Running this even fails and returns with an error.
Return to stock
------------------
This only works if you did a backup of the flash before flashing
OpenWrt. Stock dump then can be flashed from within U-Boot or OpenWrt.
There is no vendor firmware image because this is an unmanaged switch!
CAUTION: Make sure to not overwrite the U-Boot partition(s). If you do
not have a flash programmer, you may not be able to debrick
your device then.
Co-authored-by: Balázs Triszka <balika011@gmail.com>
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
AIC8800 is a WiFi/BT module based on Ceva's IP.
This driver is old and not enabled in the starfive target,
so remove it. We can add out of tree drivers if necessary.
Fixes: 8f0f02d2 ("starfive: 6.12: refresh patches and drop upstreamed ones")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Add support for Xiaomi AX6000.
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Etrontech EM6HE16EWAKG 512 MiB DDR3L-933
* Serial Port: 1v8 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax - up to 574 Mbps)
QCN9024 (4x4 5 Ghz 802.11an/ac/ax - up to 4804 Mbps)
QCA9887 (1x1 5 Ghz 802.11ac/n - up to 433 Mbps)
* Ethernet: IPQ5018 integrated virtual switch connected to:
- external QCA8337 switch (3 LAN Ports 10/100/1000)
- QCA8081 Phy WAN port (10/100/1000/2500)
* Flash: Either of:
- Gigadevice GD5F1GQ4RE9IGD (128 MiB)
- ESMT F50D1G41LB (128 MiB)
* LEDs: 1x WLAN Link (GPIO 23 Active High)
1x System Blue (GPIO 24 Active High)
1x System Yellow (GPIO 25 Active High)
1x WAN Link Blue (GPIO 26 Active High)
1x WAN Link Yellow (GPIO 27 Active High)
1x Green - Unused(GPIO 28 Active High)
3x LAN Phy Green
1x WAN Phy Green
* Buttons: 1x Reset (GPIO 38 Active Low)
Known issue:
- QCA9887 doesn't come up (possibly due to 1-lane PCIe phy not coming up or missing method to drive power),
hence the host PCIe controller is disabled in the DTS.
Flash instructions:
Download XMIR Patcher: https://github.com/openwrt-xiaomi/xmir-patcher
First flash a ubinized OpenWrt initramfs that will serve as the intermediate step, since
OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for
packages, through either of the below two methods:
Installation via XMIR Patcher:
1. Load the initramfs image: openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi
Installation via ubiformat method, through SSH:
1. If needed, enable SSH using XMIR Patcher.
2. Copy the file openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi to the /tmp directory
3. Open an SSH shell to the router
4. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
5. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd18 and mtd19 are the correct indexes from above!
6. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
7. Reboot the device by:
reboot
Continue in order to pernamently flash OpenWrt:
1. Upload the sysupgrade image to /tmp/ using SCP:
scp -O <path to image> root@192.168.1.1:/tmp/
2. Open an SSH shell to 192.168.1.1 from a PC within the same subnet
3. Use sysupgrade to flash the sysupgrade image:
sysupgrade -n -v /tmp/openwrt-qualcommax-ipq50xx-xiaomi_ax6000-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upon detecting the ID for the ESMT F50D1G41LB chip, the fifth byte
returned is always 0x00 instead of the expected JEDEC continuation code
of 0x7f. This causes detection to fail:
[ 0.304399] spi-nand spi0.0: unknown raw ID c8117f7f00
[ 0.508943] spi-nand: probe of spi0.0 failed with error -524
So let's revert back to the 4 byte ID code for this chip
specifically.
Fixes: 4bd14b2fd8a8 ("mtd: spinand: esmt: Extend IDs to 5 bytes")
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/19004
Signed-off-by: Robert Marko <robimarko@gmail.com>
The qca8k dsa switch can use either an external or internal mdio bus.
This depends on whether the mdio node is defined under the switch node
itself and, as such, the internal_mdio_mask is populated with its
internal phys. Upon registering the internal mdio bus, the
internal_mdio_bus of the dsa switch is assigned to this bus.
When an external mdio bus is used, it is left unassigned, though its id
is used to create the device names of the leds.
This leads to the leds being named '(efault):00:green:lan' and so on as
the internal_mdio_bus is null. So let's fix this by adding a null check
and use the devicename of the external bus instead when an external bus
is configured.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Continuous read does not work properly in on-die ECC mode.
Disable it to fix ubi io error on the GL.iNet GL-MT3000.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Fix wrong pwm-fan node for bpi-r4.
Remove useless status for pwm-fan.
Remove blank lines added by b992aa11.
Fixes: b992aa11 ("mediatek: dts: bring mt7988a.dtsi closer to upstream")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
5be4c60a9084 ipq5018: add BDF for Xiaomi AX6000
22588512b844 qcn9074: add BDF for Xiaomi AX6000
4810aacf3b1c qca9889: add BDF for Xiaomi AX6000
Signed-off-by: Robert Marko <robimarko@gmail.com>
- pre-install calls preinst
- pre-upgrade calls preinst with PKG_UPGRADE=1
- post-upgrade calls postinst with PKG_UPGRADE=1
- prerm and postrm from the previous version of a package are NOT
executed on upgrade, so packages are expected to handle their own
migrations in the new versions
Link: https://wiki.alpinelinux.org/wiki/Creating_an_Alpine_packageFixes: #18527
Reported-by: Dobroslaw Kijowski <dobo90@gmail.com>
Suggested-by: Eric Fahlgren <ericfahlgren@gmail.com>
Suggested-by: Jonas Gorski <jonas.gorski@gmail.com>
Suggested-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: George Sapkin <george@sapk.in>
Link: https://github.com/openwrt/openwrt/pull/18531
Signed-off-by: Robert Marko <robimarko@gmail.com>
QCN6122 wifi in fw-memory-mode 1 has a slightly larger caldb size than
currently defined in the ath11k driver. When coldboot calibration was
disabled, the fw mem mode was changed from 2 (256MB mem profile) to 1
(512MB mem profile), which is the correct setting for devices in scope.
However, in fw mem mode, the caldb size is 0x500000 instead of the max
0x480000 defined in the driver, causing QCN6122 wifi failing to boot:
ath11k b00a040.wifi1: qmi mem size is low to load caldata
ath11k b00a040.wifi1: failed to assign qmi target memory: -22
As such, change the max caldb memory size accordingly.
This macro is used by the driver only as a max size limit to validate
the requested caldb size returned by QMI. Different ath11k wifi chips
have different caldb sizes (for ex. the size for IPQ5018 is 0x200000).
Fixes: cf715a2305 ("wifi: ath11k: disable coldboot calibration for ipq5018")
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19118
Signed-off-by: Robert Marko <robimarko@gmail.com>
54b00e3b1fa9 ubus: fix double registry clear on disconnect
69521b55855c ubus: fix use-after-free on deferred request reply() method
22e8c16d9deb debug: fix crash when passing tagged string to getinfo()
2c9eea5174d6 ubus: use ucv_resource_create_ex for connections/channels
0a4cf4b7e71a ubus: use ucv_resource_create_ex for for ubus.request resources
99ee75a69cd3 ubus: use ucv_resource_create_ex for ubus.deferred resources
f085a42b977f ubus: use ucv_resource_create_ex for objects
94ad17d13a0d ubus: use ucv_resource_create_ex for ubus.notify resources
a3fa47fdda3e ubus: use ucv_resource_create_ex for ubus.listener resources
9ab5fa869dec ubus: use ucv_resource_create_ex for ubus.subscriber resources
be92ebd70633 CI: debian: install cmake package
fd202fd40bd1 socket: respect port argument in sockinst.connect()
767c209b917b socket: properly handle async `connect(2)` errors in socket.connect()
37ac8f112af6 socket: improve port argument validation in sockinst.connect()
Fixes: https://github.com/jow-/ucode/issues/302
Fixes: https://github.com/jow-/ucode/issues/303
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Only 2 devices use leading zeroes to pad interface names,
align the remaining ones so that it is consistent.
Signed-off-by: Joe Holden <jwh@zorins.us>
Link: https://github.com/openwrt/openwrt/pull/18913
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
- SoC: Broadcom BCM6358 dual 300MHz MIPS
- Flash: 16MB NOR
- RAM: 64MB DDR
- Ethernet: 4x 100M
- Wifi: Broadcom BCM4318
- 2x USB 2.0 port
- 2x Button
- 9x LED
- RJ11 2x FXS VoIP (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
- Assign static IP 192.168.1.100 to PC.
- Unplug the power source.
- Press the RESTART button at the router, don't release it yet!
- Plug the power source and wait at least 15 seconds.
- Release the RESTART button.
- Browse to http://192.168.1.1 with your PC.
- Upload the openwrt-bmips-bcm6358-huawei_hg553-squashfs-cfe.bin file.
- Wait some minutes until the firmware upgrade completes.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Remove upstream backport patch.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/19100
Signed-off-by: Robert Marko <robimarko@gmail.com>
I-O DATA WN-DAX3000GR is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based
on IPQ5018.
Specification:
- SoC : Qualcomm IPQ5018
- RAM : DDR3 512 MiB
- Flash : SPI-NAND 128 MiB (Macronix MX35UF1G24AD-Z4I)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm IPQ5018 (SoC)
- 5 GHz : Qualcomm Atheros QCN6102
- Ethernet : 5x 10/100/1000 Mbps
- wan (phy) : Qualcomm IPQ5018 (SoC)
- lan (switch) : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO): 7x/5x
- UART : through-hole on PCB (J3)
- assignment : 3.3V, TX, RX, NC, GND from tri-angle marking
- settings : 115200n8
- USB : USB 2.0 Type-A (through-hole on PCB, "J6")
- Power : 12 VDC, 1A (Typ. 930 mA)
Flash instruction using factory.bin image:
1. Boot WN-DAX3000GR with router mode
2. Access to the WebUI ("http://192.168.0.1/") on the device and open
the firmware update page ("ファームウェア")
3. Select the OpenWrt factory.bin image and click update ("更新") button
4. Wait ~120 seconds to complete flashing
Switching to the stock firmware:
1. Load the elecom.sh script
. /lib/upgrade/elecom.sh
2. Check the current index of rootfs
bootconfig_rw_index 0:bootconfig rootfs
3. Set the index to inverted value
bootconfig_rw_index 0:bootconfig rootfs <value>
bootconfig_rw_index 0:bootconfig1 rootfs <value>
example:
- step2 returned "0":
bootconfig_rw_index 0:bootconfig rootfs 1
bootconfig_rw_index 0:bootconfig1 rootfs 1
- step2 returned "1":
bootconfig_rw_index 0:bootconfig rootfs 0
bootconfig_rw_index 0:bootconfig1 rootfs 0
4. Reboot
Partition Layout (Stock FW, bootconfig(rootfs)=1):
0x000000000000-0x000000080000 : "0:SBL1"
0x000000080000-0x000000100000 : "0:MIBIB"
0x000000100000-0x000000140000 : "0:BOOTCONFIG"
0x000000140000-0x000000180000 : "0:BOOTCONFIG1"
0x000000180000-0x000000280000 : "0:QSEE"
0x000000280000-0x000000380000 : "0:QSEE_1"
0x000000380000-0x0000003c0000 : "0:DEVCFG"
0x0000003c0000-0x000000400000 : "0:DEVCFG_1"
0x000000400000-0x000000440000 : "0:CDT"
0x000000440000-0x000000480000 : "0:CDT_1"
0x000000480000-0x000000500000 : "0:APPSBLENV"
0x000000500000-0x000000640000 : "0:APPSBL"
0x000000640000-0x000000780000 : "0:APPSBL_1"
0x000000780000-0x000000880000 : "0:ART"
0x000000880000-0x000000900000 : "0:TRAINING"
0x000000900000-0x000003c40000 : "rootfs_1"
0x000003c40000-0x000003fc0000 : "Config"
0x000003fc0000-0x000007300000 : "rootfs"
0x000007300000-0x000007680000 : "Config_2"
0x000007680000-0x000007700000 : "idmkey"
0x000007700000-0x000007c00000 : "Reserved"
0x000007c00000-0x000007c80000 : "FWHEADER"
0x000007c80000-0x000007d00000 : "Factory"
Known Issues:
- This device has a Macronix MX35UF1G24AD SPI-NAND chip registered as
oobsize=128 in Linux Kernel. But using BCH8 breaks I/O on the chip
with the following errors, so this support uses BCH4 instead.
[ 1.542261] 0x000000480000-0x000000500000 : "0:appsblenv"
[ 1.547959] 1 fixed-partitions partitions found on MTD device 0:appsblenv
[ 1.551265] Creating 1 MTD partitions on "0:appsblenv":
[ 1.558096] 0x000000000000-0x000000040000 : "env-data"
[ 1.627282] u-boot-env-layout 79b0000.qpic-nand:flash@0:partitions:partition-0-appsblenv:partition@0:nvmem-layout: probe with driver u-boot-env-layout failed with error -74
root@OpenWrt:~# strings /dev/mtdblock10
[ 77.806720] mtdblock: MTD device '0:appsblenv' is NAND, please consider using UBI block devices instead.
[ 77.807554] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0
[ 77.815977] I/O error, dev mtdblock10, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0
[ 77.824721] I/O error, dev mtdblock10, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 0
[ 77.834095] I/O error, dev mtdblock10, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0
[ 77.843278] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 77.851577] Buffer I/O error on dev mtdblock10, logical block 0, async page read
Notes:
- This device has dual-boot feature and it's managed by the index in the
0:bootconfig and 0:bootconfig1 partitions.
- There are through-holes on PCB for USB 2.0, but it cannot be accessed
without disassembly of the housing. So it's not enabled in this
support.
- WN-DAX3000GR has the "bt_fw" volume in the firmware UBI in addition to
the volumes that will be removed in the section of ELECOM WRC-X3000GS2
in /lib/upgrade/platform.sh.
That volume is unnecessary for OpenWrt and add
`remove_oem_ubi_volume bt_fw` to remove that volume when sysupgrade.
(that function doesn't anything without errors if no specified volume)
MAC Addresses:
LAN : 50:41:B9:xx:xx:64 (0:APPSBLENV, "ethaddr"/"eth1addr" (text))
WAN : 50:41:B9:xx:xx:66 (0:APPSBLENV, "eth0addr" (text))
2.4 GHz: 50:41:B9:xx:xx:64 (0:APPSBLENV, "wifi0" (text))
5 GHz : 50:41:B9:xx:xx:65 (0:APPSBLENV, "wifi1" (text))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19053
Signed-off-by: Robert Marko <robimarko@gmail.com>
I-O DATA WN-DAX3000GR has a MSTC (Mitra Star Technology Corp.) specific
header with a different length than ELECOM WRC-X3000GS2.
Make the header length configurable by parameterizing on
Build/mstc-header.
- WRC-X3000GS2: 0x400
- WN-DAX3000GR: 0x480
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19053
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for I-O DATA WN-DAX3000GR to update bootdelay variable while
sysupgrade.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19053
Signed-off-by: Robert Marko <robimarko@gmail.com>
The reason fwmode 2 was used for ipq5018 and qcn6122 wifi was that
coldboot calibration doesn't work and causes the firmware to crach
during wifi bringup. Since coldboot calibration is now disabled in the
driver, all boards can now use their respective firmware memory mode, so
let's the property in all board DTS files accordingly.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19083
Signed-off-by: Robert Marko <robimarko@gmail.com>
Coldboot calibration does not work causes the firmware to crash during
wifi startup. So let's disable coldboot calibration until a solution is
found.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19083
Signed-off-by: Robert Marko <robimarko@gmail.com>
The I2C and SPI packages required for each RPi generation is different.
Therefore, in order to avoid confusion let's select them by default.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Three different code paths for the same phy model. Now the bus
is prepared to handle c45 (mmd) read/writes correctly. Remove
the custom implementations and let generic kernel functions do
their best. To achieve this
- disable the PHY-mode EEE in rtl821x_config_init() as upstream does
- provide mmd read/write functions that avoid EEE via c45 over c22
While chaning the phy_driver functions sort them alphabetically.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
rtl8214fc_media_is_fibre() will need to be run when bus lock is held.
Split the function into two versions.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
As the mdio bus has been hardened and can now handle c45 requests
the DSA driver must honor that as well. For this
- add proper upstreamed bus read_c45 and write_c45 functions
- take over the disabled port mask from upstream bus
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
With the follow up EEE patches the mdio bus will run c22 and c45
accesses during initial scan. Especially when accessing addresses
beyond the CPU port phy requests might fail in a way that cannot
be handled gratefully. Do two things
- do not allow access to addresses starting from cpu port
- set the scan disable bitmask to ports starting from cpu port
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some bits where missed during the last enhancement of the mdio
patch. In the forthcoming patches the phy_mask will be populated
to avoid unwanted ports (>= cpu port) from being scanned. Add
additional locations where 32 bit values need to be converted
to 64 bits.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
If mmd and normal phy ops are issued the bus is lost because
of wrong park page settings. Force it to 0x1f as in GPL.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
Allow to build the new kernel.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
The new kernel has relocated the definition of struct platform_device.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
The DSA driver uses set_mac_eee() for the outside API while
the interal helper is called port_eee_set(). Align that.
Additionally do not call the internal helpers directly by
the function names but use the register assignments.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18935
Signed-off-by: Robert Marko <robimarko@gmail.com>
