Commit graph

64373 commits

Author SHA1 Message Date
Álvaro Fernández Rojas
dbffeebea4 bmips: huawei,hg556a-b: enable external switch
The external switch of the Huawei HG556a is a BCM5325E connected by MDIO.

All the DSA brcm legacy FCS tag and b53 patches have been submitted upstream
and will be backported when accepted.

There are still some sporadic FDB errors, but at least the switch is working
and stable on my device:
bcm53xx fffe4800.ethernet-mii:1e: port 0 failed to add 72:31:59:xx:xx:xx vid 1 to fdb: -28
bcm53xx fffe4800.ethernet-mii:1e: port 0 failed to add 5c:4c:a9:xx:xx:xx vid 0 to fdb: -28
bcm53xx fffe4800.ethernet-mii:1e: port 0 failed to add 5c:4c:a9:xx:xx:xx vid 1 to fdb: -28
bcm53xx fffe4800.ethernet-mii:1e: port 0 failed to delete 72:31:59:xx:xx:xx vid 1 from fdb: -2

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2025-06-01 20:48:06 +02:00
Zoltan HERPAI
a3cd610b28 pistachio: drop 6.6 support
Drop configs and patches for Linux 6.6.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2025-06-01 16:24:34 +02:00
Zoltan HERPAI
56b9ceef64 pistachio: use kernel 6.12 by default
Switch to Linux kernel version 6.12.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2025-06-01 16:24:34 +02:00
Alexandru Gagniuc
ba674fea40 realtek: support EnGenius EWS2910P v3
Add support for V3 of the Engenius EWS2910P PoE switch. Like its v1
brother, This is an RTL8380 based switch with two SFP slots, and PoE
802.3af one every RJ-45 port.

Unlike its older brother, the max budget is 55W instead of 61.6 W.
Investigation into the communication protocol with the PoE controller
is ongoing, though it appears the vendor firmware configures the PSE
with a per-port budget of 30.0W.

Specifications:
---------------
* SoC:       Realtek RTL8380M
* Flash:     32 MiB SPI flash Macronix MX25L25635E
* RAM:       256 MiB (As reported by bootloader)
* Ethernet:  8x 10/100/1000 Mbps with PoE
             2x SFP slots
* Buttons:   1 "Reset" button on front panel
             1 "LED mode: button on front panel
             1 "On/Off" Toggle switch on the back
* Power:     48V-54V DC barrel jack
* UART:      1 serial header (JP1) with populated 2.54mm pitch header
             Labeled GRTV for ground, rx, tx, and 3.3V respectively
* PoE:       1 STM ST32... microcontroller (U15)
             1 RTL8238B PSE controller
Works:
------
  - (8) RJ-45 ethernet ports
  - Switch functions
  - LEDs and buttons

Not yet enabled:
----------------
  - Power-over-Ethernet (requires realtek-poe support for RTL8232B)

Install via web interface:
-------------------------

The factory firmware will accept and flash the initramfs image. It is
recommended to flash to "Partition 0". Flashing to "Partition 1" is
not supported at this point.

The factory web GUI will show the following warning:

 " Warning: The firmware version is v0.00.00-c0.0.00
     The firmware image you are uploading is older than the current
     firmware of the switch. The device will reset back to default
     settings. Are you sure you want to proceed?"

This is expected when flashing OpenWrt. After the initramfs image
boots, flash the -sysupgrade using either the commandline or LuCI.

Install via serial console/tftp:
--------------------------------

See commit 2cfaab4549 ("realtek: add support for EnGenius EWS2910P").

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15217
Signed-off-by: Robert Marko <robimarko@gmail.com>
2025-05-31 23:19:01 +02:00
Alexandru Gagniuc
e5625fb448 realtek: engenius_ews2910p: support multiple hardware versions
When the Engenius EWS-2910P was added, only v1 was known. Move the
common parts to a dtsi, and split up the support to acccount for the
hardware version.

On v3, for example, the root partition uses a different uImage magic.

Add a "engenius,ews2910p-v1" compatible, while leaving the legacy
"engenius,ews2910p" to also mean v1.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15217
Signed-off-by: Robert Marko <robimarko@gmail.com>
2025-05-31 23:19:01 +02:00
Enrico Mioso
2a32d215ba uboot-mediatek: bump to v2025.04
The following upstreamed / superseded patches were dropped:

 060-01-clk-mediatek-mt7629-fix-parent-clock-of-some-top-clo.patch
 060-02-arm-dts-mt7629-fix-sgmii-clock-selection-for-etherne.patch
 060-03-net-mediatek-use-correct-register-field-for-SGMII-sp.patch
 060-04-net-mediatek-correct-register-name-of-ethsys-syscfg1.patch
 060-05-net-mediatek-fix-sgmii-selection-for-mt7622.patch
 060-06-net-mediatek-fix-gmac2-usability-for-mt7629.patch
 060-07-net-mediatek-add-support-for-10GBASE-R.patch
 060-08-net-mediatek-make-sgmii-usxgmii-optional.patch
 060-09-net-mediatek-don-t-enable-GDMA-cpu-bridge-unconditio.patch
 060-10-net-mediatek-fix-usability-with-wget-command.patch
 061-01-net-mediatek-split-ethernet-switch-code-from-mtk_eth.patch
 061-02-net-mediatek-add-support-for-MediaTek-MT7987-SoC.patch
 061-03-net-mediatek-add-support-for-Airoha-AN8855-ethernet-.patch
 070-01-board-mediatek-mt7622-remove-board_late_init.patch
 070-02-clk-mediatek-fix-uninitialized-fields-issue-in-INFRA.patch
 070-03-configs-mt7629-move-image-load-address-to-0x42000000.patch
 070-04-configs-mt7988-move-image-load-address-to-0x44000000.patch
 070-05-spi-mtk_spim-add-support-to-use-DT-live-tree.patch
 070-06-spi-mtk_spim-check-slave-device-mode-in-spi-mem-s-su.patch
 070-07-arm-dts-mediatek-add-quad-mode-capabilities-for-SPI-.patch
 070-08-pwm-mediatek-add-pwm3-support-for-mt7981.patch
 070-09-pci-mediatek-add-support-for-multiple-ports-in-media.patch
 070-10-arm-dts-mediatek-add-pcie-support-for-mt7988.patch
 070-11-arm-dts-medaitek-fix-internal-switch-link-speed-of-m.patch
 070-12-arm-dts-mediatek-add-support-for-all-three-GMACs-for.patch
 070-13-arm-dts-medaitek-add-flash-interface-driving-setting.patch
 070-14-arm-dts-mediatek-update-mt7981-mmc-node.patch
 070-15-MAINTAINERS-update-file-list-for-MediaTek-ARM-platfo.patch
 071-01-pinctrl-mediatek-update-mt7981-pinctrl-driver-based-.patch
 100-18-board-mt7629-add-support-for-booting-from-SPI-NAND.patch
 290-mt7981-add-USB-nodes.patch

Refreshed all the patches needing it.

Run-tested: GatoNetworks GDSP, Arcadyan Mozart (ynezz),
            Zbt WG3526 (dangowrt)

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [patch refresh, Mozart testing]
Signed-off-by: Daniel Golle <daniel@makrotopia.org> [rebased, tested on MT7621]
2025-05-31 21:16:41 +02:00
Philip Prindeville
c6c29d7b38 sysupgrade: create 10_disable_services w/ fixed modified time
Every time "sysupgrade -b -" runs it would generate a new
(synthetic) "/etc/uci-defaults/10_disable_services" file with
the current time as the modified time.  This unfortunately
creates a non-deterministic tarball, so if you run a cron job
to save your state, you don't have a trivial way of seeing if
it changed or not without unpacking the archive, deleting this
file, and comparing the entire directory tree to the previous
backup.

Fixes: #16145
Fixes: 0ad062a21b ("base-files: sysupgrade: include uci-defaults script disabling services #2")
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
2025-05-31 11:18:50 -06:00
Shiji Yang
30cdc48360 kernel: bump 6.12 to 6.12.31
Changelog: https://cdn.kernel.org/pub/linux/kernel/v6.x/ChangeLog-6.12.31

Remove upstreamed patches:
  backport-6.12/780-27-v6.15-r8169-don-t-scan-PHY-addresses-0.patch [1]
  backport-6.12/780-33-v6.15-r8169-disable-RTL8126-ZRX-DC-timeout.patch [2]
  bcm27xx/patches-6.12/950-0315-media-i2c-imx219-Correct-the-minimum-vblanking-value.patch [3]
  bcm27xx/patches-6.12/950-0857-drm-v3d-Add-clock-handling.patch [4]
  bcm27xx/patches-6.12/950-0874-PCI-brcmstb-Expand-inbound-window-size-up-to-64GB.patch [5]
  bcm27xx/patches-6.12/950-0877-PCI-brcmstb-Adding-a-softdep-to-MIP-MSI-X-driver.patch [6]
  bcm27xx/patches-6.12/950-0960-media-imx335-Set-vblank-immediately.patch [7]

Manually rebased patches:
  d1/patches-6.12/0009-ASoC-sunxi-sun4i-codec-add-basic-support-for-D1-audi.patch

[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.12.31&id=ba59747562c49974cbace989d76b94a8331da442
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.12.31&id=2780aa8394415df0a69e3b908d6dd8c79e1d1bcc
[3] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.12.31&id=9a981079097bee6a0583877798de0b240717bdde
[4] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.12.31&id=bbd6dc1fb6c56267ad1d58810d92287fcd5b0058
[5] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.12.31&id=3ffaa2e999380477774e76680ff4cef247451168
[6] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.12.31&id=12153e3948c596737853c3ec4ff7e4e3f4a9f9a6
[7] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v6.12.31&id=8d7e13c31c52690655883dff604238b0760a3644

Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18953
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2025-05-31 17:35:29 +02:00
Felix Fietkau
6296c17026 cli: return the correct data type for enum attributes
Return entries from the value array instead of the provided string

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2025-05-31 16:23:47 +02:00
Felix Fietkau
91d33d1563 mac80211: allow scanning operating on DFS channels
Only for multi-radio configurations where the scan would not affect the radio
running DFS detection

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2025-05-31 16:23:03 +02:00
Felix Fietkau
ed26185bf6 hostapd: tweak ACS retry behavior
When running ACS on multi-radio devices, ACS on one band can block another.
Increase the number of retries and prevent bouncing interfaces between AP
and STA mode during attempts.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2025-05-31 16:22:48 +02:00
Felix Fietkau
71bec727c8 cli: fix dealing with enum types with object value lists
Convert to array before calling filter()

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2025-05-31 16:22:46 +02:00
Felix Fietkau
e29669dae1 unetmsg: set TCP timeout for outgoing connections
Avoid running into long timeouts

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2025-05-31 16:22:39 +02:00
Felix Fietkau
784dca7e3a procd: update to Git HEAD (2025-05-31)
59d22013f9dd jail: make udebug socket optional

Fixes: https://github.com/openwrt/openwrt/issues/18967
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2025-05-31 16:21:49 +02:00
Álvaro Fernández Rojas
84eefb493b generic: backport brcm legacy dsa tag fix
Backport a small fix for brcm legacy dsa tags that has been accepted for
linux v6.16.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2025-05-31 15:30:08 +02:00
Álvaro Fernández Rojas
ba1017bf74 generic: backport bcm63xx SPI reset fix
Fixes SPI and HSSPI coexistance on bmips bcm6362 and bcm63268.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2025-05-31 12:29:30 +02:00
Markus Stockhausen
9716f89df6 realtek: enhance & harmonize dsa/phy max port patches
DSA silently drops internal phy access to ports >= 32 in dsa_user_phy_read()
and dsa_user_phy_write(). The code shows:

static int dsa_user_phy_read(struct mii_bus *bus, int addr, int reg)
{
	struct dsa_switch *ds = bus->priv;

	if (ds->phys_mii_mask & (1 << addr))
		return ds->ops->phy_read(ds, addr, reg);

	return 0xffff;
}

With ds->phys_mii_mask being a 32 bit variable the reason is clear. So do
not only increase the max values but also adapt the needed bitmasks in
the dsa and phy code. This fixes the dsa_user_ports() and dsa_cpu_ports()
too.

While we are here combine the old separated patches because dsa, mdio and
phy are tigthly coupled.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18846
Signed-off-by: Robert Marko <robimarko@gmail.com>
2025-05-31 12:28:14 +02:00
Alexandru Gagniuc
22dc34e8c1 qualcommbe: v6.12: enable 2.5G and 10G phylink modes in pcs-qcom-ipq9574
The PCS driver in the 6.12 patchset is the v5 submission (see link
below). It solves a number of issues and crashes with teh pcs driver
from the 6.6 patchset. However, this new driver is missing support for
"10gbase-r", "10g-qxgmii", and 1000/2500base-x modes.

Port these modes to the 6.12 patchset. "2500base-x" in particular seems
to be needed to establish a 2.5G link on phy-mode="usxgmii";

Link: https://lore.kernel.org/lkml/20250207-ipq_pcs_6-14_rc1-v5-0-be2ebec32921@quicinc.com/
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
2025-05-31 12:25:49 +02:00
Alexandru Gagniuc
3d6c36e327 qualcommbe: enable v6.12 testing kernel
Now that patches for v6.12 are available, add the config, and enable
6.12 as a testing kernel.

Compared to v6.6 the patches to add "10gbase-r", "2500base-x",
"1000base-x", and "10g-qxgmii" modes have not been ported yet. They do
not apply cleanly to the new PCS driver. As the currently supported
hardware does not use those modes, it is not possible to test them at
this time.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
2025-05-31 12:25:49 +02:00
Alexandru Gagniuc
1fc5e2ec90 qualcommbe: add v6.12 config from v6.6
Copy the v6.6 config to v6.6. It will be updated in a subsequent
commit in order to show the changes.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
2025-05-31 12:25:49 +02:00
Alexandru Gagniuc
627daef0cf qualcommbe: v6.12: add NSSCC clock and reset fixes
Port reset and clock fixes from target/linux/qualcommbe/patches-6.6.
Modifications of v6.6 patches are noted in each commit body.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
2025-05-31 12:25:48 +02:00
Alexandru Gagniuc
26ea222e21 qualcommbe: v6.12: enable ethernet for RDP433
Now that ethernet is supported on IPQ9574, add the port nodes and
other requirements to enable ethernet on RDP433.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
2025-05-31 12:25:48 +02:00
Alexandru Gagniuc
f3fc278fcb qualcommbe: v6.12: add PPE driver (part 2)
Add the second part of the PPE driver. This includes the EDMA and
network device support. This part does not appear to have been
officially submitted for upstream review. The series is taken from
target/linux/qualcommbe/patches-6.6, and had to be heavily modified
in order to compile of v6.12. Changes to patches are noted in the
respective patch body.

Also add the PPE and EDMA nodes in this series.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
2025-05-31 12:25:48 +02:00
Alexandru Gagniuc
cd9f3b8d33 qualcommbe: v6.12: add pending PPE driver (part 1)
Add v3 submission of the qualcomm PPE driver. As of this writing, it
is the latest version. This lacks the EDMA driver and network device
support. That will be added in part 2.

Link: https://lore.kernel.org/lkml/20250209-qcom_ipq_ppe-v3-0-453ea18d3271@quicinc.com
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
2025-05-31 12:25:48 +02:00
Alexandru Gagniuc
3744b73602 qualcommbe: v6.12: add ethernet PCS driver for IPQ9574
Add the v5 of the PCS patch. This is the latest submission as of this
writing. THe last four patches are not part of the submission. They
make the series work with v6.12 kernel, resolve a circular dependency
with the clocks, and add the DTS node. Include them as bundle.

Link: https://lore.kernel.org/lkml/20250207-ipq_pcs_6-14_rc1-v5-0-be2ebec32921@quicinc.com/
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
2025-05-31 12:25:48 +02:00
Alexandru Gagniuc
390e516a3b qualcommbe: v6.12: add QCA8084 ethernet PHY driver
This driver is cherry-picked from target/linux/qualcommbe/patches-6.6.
While Qualcomm did submit past patches for QCA8084, the code has since
ben split from at803x. The existing OpenWRT version of the patch is
the cleanest version I could find. Add it here.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
2025-05-31 12:25:48 +02:00
Alexandru Gagniuc
8f4100ac3b qualcommbe: v6.12: add various DTS updates for IPQ9574 and RDP433
These devicetree updates can work with the existing upstreamcode. They
do not require code changes. Add them before any code change.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
2025-05-31 12:25:48 +02:00
Alexandru Gagniuc
01f3624960 qualcommbe: v6.12: add pending patches
Add dts fixes from linux-next. Two patches from the NSSCC series are
still in -next did not yet land in mainline, as well as misc other DTS
changes. Add them here.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
2025-05-31 12:25:48 +02:00
Alexandru Gagniuc
e3478dbd69 qualcommbe: v6.12: add upstreamed patches
Add relevant patches from upstream, up to v5.16-rc6. The gaps in the
patch numbersing are either patches that were picked into the stable
kernel (6.12.y), or that are already backported in
target/linux/generic. The gaps makes it easy for me to pick these
patches from my working kernel git branch.

Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
2025-05-31 12:25:48 +02:00
Vladislav Grigoryev
d989d9a8ec base-files: use cidr for config_generate
Generate network configuration replacing netmask with CIDR.

Depends on:
https://github.com/openwrt/openwrt/pull/13765

Using CIDR provides the following advantages:
* Consolidate notation for IPv4 and IPv6 addresses.
* Consolidate notation for IP addresses and routing targets.
* Simplify network configuration and troubleshooting.
* Follow the transition from net-tools to iproute2.

Resulting configuration example:
```
config interface 'loopback'
	option device 'lo'
	option proto 'static'
	list ipaddr '127.0.0.1/8'

config interface 'lan'
	option device 'br-lan'
	option proto 'static'
	list ipaddr '192.168.1.1/24'
```

Signed-off-by: Vladislav Grigoryev <vg.aetera@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/13780
Signed-off-by: Robert Marko <robimarko@gmail.com>
2025-05-30 22:55:27 +02:00
Christian Marangi
427c4aa266
ath79: add calibtation variant for TP-Link Archer C6 v2
Now that we have a board file, add calibration variant for TP-Link
Archer C6 v2 and add ipq-wifi package for it.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2025-05-30 21:35:11 +02:00
Christian Marangi
c88515dd86
ipq-wifi: Add entry for TP-Link Archer C6 v2
Add IPQ Wifi entry for Ath79 TP-Link Archer C6 v2.

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2025-05-30 21:35:11 +02:00
Christian Marangi
8dd0020d1a
ipq-wifi: update to Git HEAD (2025-05-30)
576ade747259 CI: add action that prints info about submited BDF-s
1d688e8654a5 qca9888 : add BDF for Yuncore WB5G08
ddfd9d2f3a8e ipq60xx: rename BDF for EAP623-Outdoor HD v1
bab36c1d947d ath10k: drop upstramed board files
09e5afab85b2 CI: add QCA9988
fde3d2a7ce59 qca9888: add TP-Link Archer C6 v2 (EU) BDF

Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2025-05-30 21:26:15 +02:00
Zoltan HERPAI
e05426aaf8 sunxi: enable crypto offload engine
Enable the sun8i_ce and sun8i_ss crypto engines that are included on
various Allwinner SoCs, along with their respective hash/prng/trng
options.

sun8i_ce: H2+, H3, H5, H6, R40 and A64
sun8i_ss: A80, A83T

BananaPi P2 Zero (H2+):

[    0.373860] sun8i-ce 1c15000.crypto: Set mod clock to 50000000 (50 Mhz) from 24000000 (24 Mhz)
[    0.374326] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority
[    0.374516] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority
[    0.374657] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority
[    0.374788] sun8i-ce 1c15000.crypto: will run requests pump with realtime priority
[    0.374924] sun8i-ce 1c15000.crypto: Register cbc(aes)
[    0.374962] sun8i-ce 1c15000.crypto: Register ecb(aes)
[    0.374976] sun8i-ce 1c15000.crypto: Register cbc(des3_ede)
[    0.374990] sun8i-ce 1c15000.crypto: Register ecb(des3_ede)
[    0.375005] sun8i-ce 1c15000.crypto: Register md5
[    0.375019] sun8i-ce 1c15000.crypto: Register sha1
[    0.375032] sun8i-ce 1c15000.crypto: Register sha224
[    0.375046] sun8i-ce 1c15000.crypto: Register sha256
[    0.375061] sun8i-ce 1c15000.crypto: Register sha384
[    0.375075] sun8i-ce 1c15000.crypto: Register sha512
[    0.375109] sun8i-ce 1c15000.crypto: Register stdrng
[    0.375150] sun8i-ce 1c15000.crypto: TRNG not supported
[    0.375157] sun8i-ce 1c15000.crypto: CryptoEngine Die ID 1

BananaPi M3 (A83t):

[    0.429615] sun8i-ss 1c15000.crypto: will run requests pump with realtime priority
[    0.429866] sun8i-ss 1c15000.crypto: will run requests pump with realtime priority
[    0.430042] sun8i-ss 1c15000.crypto: DEBUG: Register cbc(aes)
[    0.430095] sun8i-ss 1c15000.crypto: DEBUG: Register ecb(aes)
[    0.430112] sun8i-ss 1c15000.crypto: DEBUG: Register cbc(des3_ede)
[    0.430128] sun8i-ss 1c15000.crypto: DEBUG: Register ecb(des3_ede)
[    0.430152] sun8i-ss 1c15000.crypto: Register md5
[    0.430171] sun8i-ss 1c15000.crypto: Register sha1
[    0.430187] sun8i-ss 1c15000.crypto: Register sha224
[    0.430203] sun8i-ss 1c15000.crypto: Register sha256
[    0.430220] sun8i-ss 1c15000.crypto: Register hmac(sha1)
[    0.430276] sun8i-ss 1c15000.crypto: Security System Die ID 7
[    0.493087] sun8i-ss 1c15000.crypto: Fallback driver could no be loaded

OrangePi Zero 2 (H616):

[    0.176833] sun8i-ce 1904000.crypto: will run requests pump with realtime priority
[    0.177054] sun8i-ce 1904000.crypto: will run requests pump with realtime priority
[    0.177167] sun8i-ce 1904000.crypto: will run requests pump with realtime priority
[    0.177258] sun8i-ce 1904000.crypto: will run requests pump with realtime priority
[    0.177361] sun8i-ce 1904000.crypto: Register cbc(aes)
[    0.177408] sun8i-ce 1904000.crypto: Register ecb(aes)
[    0.177420] sun8i-ce 1904000.crypto: Register cbc(des3_ede)
[    0.177432] sun8i-ce 1904000.crypto: Register ecb(des3_ede)
[    0.177444] sun8i-ce 1904000.crypto: Register md5
[    0.177456] sun8i-ce 1904000.crypto: Register sha1
[    0.177468] sun8i-ce 1904000.crypto: Register sha224
[    0.177479] sun8i-ce 1904000.crypto: Register sha256
[    0.177503] sun8i-ce 1904000.crypto: Register sha384
[    0.177515] sun8i-ce 1904000.crypto: Register sha512
[    0.177527] sun8i-ce 1904000.crypto: Register stdrng
[    0.177648] sun8i-ce 1904000.crypto: CryptoEngine Die ID 0

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2025-05-30 15:39:00 +02:00
Zoltan HERPAI
ab6ffa7e16 sunxi: cortexa53: enable rtc drivers
RTC has been disabled so far in the cortexa53 subtarget so far, enable
it. It's also required for the crypto trng/prng drivers on these SoC
variants (to gather IOSC noise).

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2025-05-30 15:39:00 +02:00
Zoltan HERPAI
393047e47a sunxi: drop 6.6 support
Drop configs and patches for Linux 6.6.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2025-05-30 15:39:00 +02:00
Zoltan HERPAI
01bc7a4fe7 sunxi: use kernel 6.12 by default
Switch to Linux kernel version 6.12.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2025-05-30 15:39:00 +02:00
Zoltan HERPAI
faf6ca0348 pistachio: add 6.12 testing kernel
Allow selecting 6.12 as testing kernel on pistachio.

Runtime-tested:
 - Creator Ci40 Marduk 02KZ/5+

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2025-05-30 15:32:12 +02:00
Zoltan HERPAI
d6b57d4722 pistachio: 6.12: refresh patches and kernel config
Refresh patches and configs as required.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2025-05-30 15:32:12 +02:00
Zoltan HERPAI
e757dfaf4c kernel/pistachio: Restore kernel files for v6.6
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.

For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2025-05-30 15:32:12 +02:00
Zoltan HERPAI
6f4ea1e219 kernel/pistachio: Create kernel files for v6.12 (from v6.6)
This is an automatically generated commit.

When doing `git bisect`, consider `git bisect --skip`.

Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
2025-05-30 15:32:12 +02:00
Antti Seppälä
d63663601d qmi: increase SIM power-cycle timeouts
Some modems and SIM cards take a bit longer to initialize after UIM has been
powered off. Waiting too little time can cause the qmi protocol to end up
in a loop repeatedly power-cycling the SIM card.

Avoid that by
 a) increasing the time we unconditionally sleep after --uim-power-on
 b) increasing the time we allow uqmi to wait for response for --uim-get-sim-state

Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18772
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2025-05-30 00:16:48 +02:00
Florian Eckert
32ed3db1a0 base-files: treat 'ipaddr is inside range' as warning again
The call to 'ipcalc' is used in 'dnsmasq' init script to create the
configuration. If the 'ipaddr' is in the configured range then 'ipcalc' exited
with an error whereby the START/STOP variables are unavailable.

This behaviour has changed during 'ipcalc' refactoring and now leads to a
problem when starting 'dnsmasq' if the 'ipaddr' is inside this range. To
restore the old behaviour, only a warning is issued as before and the
required variables for the 'dnsmasq' are still set.

Fixes: 854739b32c (base-files: ipcalc.sh: Rewrite in pure shell)

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/18641
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2025-05-29 23:54:18 +02:00
Florian Eckert
ae198c6ba0 dnsmasq: fix start if dhcp-range is not correct
If the uci 'dhcp' configuration for the dhcp leases is incorrect then
the call to 'ipclac' fails. However, the problem is that the dnsmasq
configuration option 'dhcp-range' is still written for this uci section
even though the information generated by ipcalc is incorrect or not set.

Due to the incorrectly generated configuration for dnsmasq, the service
cannot start.

To prevent an incorrect configuration from being written to the configuration,
a check is now made beforehand to ensure that the required variables are
present and valid. If the configuration is incorrect, a message is emitted
to the log that this configuration section is incorrect and this uci
configuration section is omitted.

Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/18641
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2025-05-29 23:54:18 +02:00
Sean Khan
b90feed6ba wifi-scripts: add missing 'network' property to wifi-iface schema
The ucode-based wifi interface validation is based on `hostapd.conf`
specific options, which means it's missing the OpenWrt-specific
'network' property.

This causes schema validation warnings like:
```
daemon.notice netifd: radio1 (1340): wifi-scripts: network is not present in the schema
```

The description is taken from the OpenWrt wiki:
https://openwrt.org/docs/guide-user/network/wifi/basic#common_options1

Signed-off-by: Sean Khan <datapronix@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/18946
Signed-off-by: Robert Marko <robimarko@gmail.com>
2025-05-29 23:48:16 +02:00
Jonas Jelonek
7d064eef52 generic: power: backport v6.15 patch to fix build with GCC15
Backports an upstream fix ([1]) for a build regression of
'drivers/power/supply' with GCC15 -Wunterminated-string-initialization.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=77f5bb150132bbbcd6bc37ffdc80c9e140e373a4

Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18950
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2025-05-29 23:16:05 +02:00
Jonas Jelonek
a5e6deb867 generic: net: add pending wireguard patch to fix build with GCC15
This patch adds __nonstring annotation to address GCC15 with
-Wunterminated-string-initialization.
It is accepted in wireguard-linux in [1] and pending for v6.16
in [2].

[1] https://git.zx2c4.com/wireguard-linux/commit/?h=devel&id=71e5da46e78c1cd24e2feed251a2845327447ad8
[2] https://patch.msgid.link/20250521212707.1767879-3-Jason@zx2c4.com

Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18950
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2025-05-29 23:13:49 +02:00
Shiji Yang
d2764bfd7e mediatek: mt7629: add the missing symbol CONFIG_LEDS_SMARTRG_LED
This symbol was lost when porting to the 6.12 kernel.

Fixes: 16b5a77716 ("mediatek: mt7629: update config-6.12")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18947
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2025-05-29 23:05:02 +02:00
Shiji Yang
0f8091334c kernel: reorder kernel symbol configs
Sort kernel configuration files alphabetically. Also resolve the
"CONFIG_ARM_PAN" conflict introduced in commit
057a0a075e ("generic: Fix up the v6.12 config for ARM"). Based on
the original PR comment[1], this symbol should be disabled by default.

[1] https://github.com/openwrt/openwrt/pull/18900#discussion_r2106253528
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18947
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2025-05-29 23:05:02 +02:00
Kyle Hendry
668704f781 sunxi: add support for Beelink X2
Specifications:
- SoC: Allwinner H3 Quad Cortex-A7 1.2GHz
- Flash: 8GB eMMC
- RAM: 1GB DDR3
- Ethernet: 1x100M
- Wifi: RTL8189FTV or AP6181
- 1x USB-A Host
- 1x USB-A Host/Device
- 2x Button
- 2x LED
- HDMI, SPDIF, IR

Install by following standard SD card flashing instructions.
Image can also be flashed to eMMC.

Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18732
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2025-05-29 22:56:04 +02:00