This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Since the early beginning of the Realtek DSA driver there is an uncovered
locking issue between the standard (parent) mdio bus and the DSA (child)
mdio bus. This comes from the fact that the DSA bus simply links to the
parent read and write functions and calls them directly. This leads to
the following lock issue.
- Child bus calls phy_read/write functions and uses its internal lock
- Parent bus calls phy_read/write functions and uses its internal lock
It becomes clear that critical section can be accessed twice without
knowing that a operation from the other bus is currently active. This
can lead to critical malfunctions because the mdio driver needs a lot of
internal magic to get page selection done right. Effects are:
- The original page is lost after a phy_write/read_paged() call
- dmesg like "Realtek RTL8218B (external) rtl838x slave mii-0:00:
Expected external RTL8218B, found PHY-ID 6b23"
Other DSA drivers simply use the read/write functions from the parent bus
and thus avoid locking issues. Do it the same way.
Fixes: 2b88563ee5 ("realtek: update the tree to the latest refactored version")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18824
Signed-off-by: Robert Marko <robimarko@gmail.com>
Before generating the factory image, check if the input file
exists. Fix the build error when sysupgrade image is too big:
[mkwrgimg] *** error: stat failed on /builder/shared-workdir/build/build_dir/target-mipsel_24kc_musl/linux-ramips_rt288x/tmp/openwrt-ramips-rt288x-airlink101_ar670w-squashfs-factory.bin, No such file or directory
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18836
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
This was needed while ar71xx was in tree. This is no longer the case.
Not only that, these have already been converted to OF.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18860
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
There are currently two power functions for the RTL8214FC in the driver
- rtl8380_rtl8214fc_on_off(): powers on/off both ports
- rtl8214fc_power_set(): powers on/off fibre or copper individually
While it seems obvious to merge these, one of them uses extended register
29 and the other register 30 to achieve the update. From looking at the
GPL source drops both methods exist with exactly the same operations. So
where to go from here? The descision was made based on:
- register 30 is only used during patching, 29 during normal operation
- Avoid raw page if possible to use function for RTL839x
So the attached patch was created. The result in the power down bits
was compared for the two old and the new implementation. Result is
always the same.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18707
Signed-off-by: Robert Marko <robimarko@gmail.com>
RTL9311 switches (like the Linksys LGS352C) will boot but have not set
the right family id in the soc_info structure. Fix that so drivers do
their work right when checking for that.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18871
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RPi upstream repo switched to the upstream SDHOST driver some time ago, so
it's time to do the same in our configs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Cleanup the code of the RTL83xx packet receive interrupt handler. Not
only for better readability but to avoid inconsistencies and stalls on
the RTL839x targets.
The current implementation seems to come from the GPL source code.
Calling the existing cleanup() function inside the interrupt context
without any locks conflicts with SMP & NAPI polling and makes things
worse instead of giving any benefit. Simply ignore RX buffer overruns
and let the device handle packet dropping itself.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18855
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Import pending PXA I2C recovery fixes so that if I2C recovery is enabled in
the DTS it does not completely break I2C as it currently does since kernel
6.6.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Use the "1/1" as a iteration count of hexdump expression instead of the
broken "1", to fix the issue that the invalid bootnum will be obtained.
Currently, the hexdump command always outputs "0" when the decimal format
and the iteration count "1" are specified[0]. This is unexpected
behaviour, but the cause is unknown and use this fix as a workaround.
[0]: https://github.com/openwrt/openwrt/issues/18808
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18827
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop configs, files and patches for Linux 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18848
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch to Linux kernel version 6.12.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18848
Signed-off-by: Robert Marko <robimarko@gmail.com>
Default qualcommax target to 6.12 kernel.
It makes no sense for us to double the effort required for backporting
upstreamed patches or for downstream modifications.
Link: https://github.com/openwrt/openwrt/pull/18840
Signed-off-by: Robert Marko <robimarko@gmail.com>
Based on other mt7622 dts, it is not difficult to infer that the
missing interrupt controller is "pio". Fix dtc warning:
mt7622.dtsi:282.3-26: Warning (interrupts_property): /ethernet@1b100000/mdio-bus/ethernet-phy@7:#interrupt-cells: size is (8), expected multiple of 12
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Add missing #address-cells, #size-cells and #sound-dai-cells to
fix the following dtc warnings:
mt7986a-bananapi-bpi-r3-respeaker-2mics.dtso:46.5-18: Warning (reg_format): /fragment@1/__overlay__/wm8960@1a:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
mt7986a-bananapi-bpi-r3-respeaker-2mics.dtso:29.11-31.7: Warning (sound_dai_property): /fragment@0/__overlay__/sound_wm8960/codec: Missing property '#sound-dai-cells' in node /fragment@1/__overlay__/wm8960@1a or bad phandle (referred from sound-dai[0])
mt7986a-rfb-spim-nand.dts:17.12-19.5: Warning (sound_dai_property): /sound_wm8960/platform: Missing property '#sound-dai-cells' in node /soc/audio-controller@11210000 or bad phandle (referred from sound-dai[0])
mt7986a-rfb-spim-nand.dts:21.9-23.5: Warning (sound_dai_property): /sound_wm8960/codec: Missing property '#sound-dai-cells' in node /soc/i2c@11008000/wm8960@1a or bad phandle (referred from sound-dai[0])
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Trim unnecessary 0s to fix the following dtc warnings:
../dts/mt7981b-cudy-re3000-v1.dts:135.20-139.6: Warning (unit_address_format): /soc/spi@11009000/flash@0/partitions/partition@00000: unit name should not have leading 0s
../dts/mt7981b-cudy-wr3000-v1.dts:153.20-157.6: Warning (unit_address_format): /soc/spi@11009000/flash@0/partitions/partition@00000: unit name should not have leading 0s
../dts/mt7981b-gatonetworks-gdsp.dts:276.20-280.6: Warning (unit_address_format): /soc/spi@11009000/flash@0/partitions/partition@00000: unit name should not have leading 0s
mt7988a-rfb-spim-nor.dtso:36.21-39.7: Warning (unit_address_format): /fragment@0/__overlay__/flash@0/partition@00000: unit name should not have leading 0s
../dts/mt7981a-ubnt-unifi-6-plus.dts:113.28-131.6: Warning (unit_address_format): /soc/spi@11009000/flash@0/partitions/partition@00000: unit name should not have leading 0s
../dts/mt7981b-wavlink-wl-wn586x3.dts:147.20-151.6: Warning (unit_address_format): /soc/spi@11009000/flash@0/partitions/partition@00000: unit name should not have leading 0s
../dts/mt7981b-wavlink-wl-wn573hx3.dts:102.20-106.6: Warning (unit_address_format): /soc/spi@11009000/flash@0/partitions/partition@00000: unit name should not have leading 0s
../dts/mt7981b-yuncore-ax835.dts:161.20-165.6: Warning (unit_address_format): /soc/spi@11009000/flash@0/partitions/partition@00000: unit name should not have leading 0s
../dts/mt7986a-zyxel-ex5601-t0-stock.dts:57.39-61.6: Warning (unit_address_format): /soc/spi@1100a000/spi_nand@0/partitions/partition@180000/nvmem-layout/macaddr@0004: unit name should not have leading 0s
../dts/mt7986a-zyxel-ex5601-t0-stock.dts:63.39-67.6: Warning (unit_address_format): /soc/spi@1100a000/spi_nand@0/partitions/partition@180000/nvmem-layout/macaddr@0024: unit name should not have leading 0s
../dts/mt7986a-zyxel-ex5601-t0-stock.dts:69.39-73.6: Warning (unit_address_format): /soc/spi@1100a000/spi_nand@0/partitions/partition@180000/nvmem-layout/macaddr@002a: unit name should not have leading 0s
../dts/mt7986a-zyxel-ex5601-t0-ubootmod.dts:56.39-60.6: Warning (unit_address_format): /soc/spi@1100a000/spi_nand@0/partitions/partition@180000/nvmem-layout/macaddr@0004: unit name should not have leading 0s
../dts/mt7986a-zyxel-ex5601-t0-ubootmod.dts:62.39-66.6: Warning (unit_address_format): /soc/spi@1100a000/spi_nand@0/partitions/partition@180000/nvmem-layout/macaddr@0024: unit name should not have leading 0s
../dts/mt7986a-zyxel-ex5601-t0-ubootmod.dts:68.39-72.6: Warning (unit_address_format): /soc/spi@1100a000/spi_nand@0/partitions/partition@180000/nvmem-layout/macaddr@002a: unit name should not have leading 0s
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Correct dts node name based on reg property to fix the
following dtc warnings:
mt7981-rfb-spim-nand.dtso:20.25-67.6: Warning (spi_bus_reg): /fragment@1/__overlay__/spi_nand@0: SPI bus unit address format error, expected "1"
mt7986a-rfb-spim-nand.dts:41.23-76.4: Warning (spi_bus_reg): /soc/spi@1100a000/spi_nand@0: SPI bus unit address format error, expected "1"
../dts/mt7981a-comfast-cf-e393ax.dts:135.23-206.4: Warning (spi_bus_reg): /soc/spi@1100a000/spi_nand@0: SPI bus unit address format error, expected "1"
../dts/mt7981b-openwrt-one.dts:305.10-342.4: Warning (spi_bus_reg): /soc/spi@1100a000/flash@0: SPI bus unit address format error, expected "1"
../dts/mt7986a-zyxel-ex5601-t0-common.dtsi:166.30-180.4: Warning (spi_bus_reg): /soc/spi@1100a000/spi_nand@0: SPI bus unit address format error, expected "1"
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
The "gpio-export" driver doesn't require a "reg" property in the
device tree, hence we don't need to use the "#size-cells" property
to describe the size of "reg".
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18290
Signed-off-by: Robert Marko <robimarko@gmail.com>
The re-factoring of the preinit factory partition mount script used the
incorrect mtd name for the EAP620HD and (I assume incorrect) for EAP660HD.
This corrects it to "factory_data".
Signed-off-by: Alex Thompson <thompson.alex.c@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18834
Signed-off-by: Robert Marko <robimarko@gmail.com>
The dependency of kmod-usb3 and kmod-usb-xhci-pci-renesas have
been reversed. Now we need to select kmod-usb-xhci-pci-renesas
instead of kmod-usb3.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18768
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The dependency of kmod-usb3 and kmod-usb-xhci-pci-renesas have
been reversed. Now we need to select kmod-usb-xhci-pci-renesas
instead of kmod-usb3.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18768
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The dependency of kmod-usb3 and kmod-usb-xhci-pci-renesas have
been reversed. Now we need to select kmod-usb-xhci-pci-renesas
instead of kmod-usb3.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18768
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove modifications for codes guarded by CONFIG_USB_PCI_AMD.
This kernel symbol is only visible on desktop level platform,
e.g. x86. They are not sensitive to firmware image size. This
patch also fixes function redefinition build errors:
drivers/usb/host/pci-quirks.c:621:6: error: redefinition of 'usb_asmedia_modifyflowcontrol'
621 | void usb_asmedia_modifyflowcontrol(struct pci_dev *pdev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/usb/host/pci-quirks.c:22:
drivers/usb/host/pci-quirks.h:49:20: note: previous definition of 'usb_asmedia_modifyflowcontrol' with type 'void(struct pci_dev *)'
49 | static inline void usb_asmedia_modifyflowcontrol(struct pci_dev *pdev) {}
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: be6753dda0 ("generic: 6.12: manually rebuild pending patches")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18637
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CONFIG_DRM_ACCEL_QAIC was not added to x86 generic config, but it needs to
be added as CONFIG_DRM_ACCEL_QAIC does not depend on x86_64 like others.
Fixes: 51b78aa ("kernel: package intel_vpu driver")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport GIC ITS support for RK356x SoC, which fixes long-standing
MSI/MSI-X bug. (Previously MSI-X could only work on one PCIe node)
e.g. [ 7.250882] r8125 0002:01:00.0: no MSI/MSI-X. Back to INTx.
Tested on Radxa E25 with kmod-r8125-rss driver.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/18800
Signed-off-by: Robert Marko <robimarko@gmail.com>
Replace RK356x RNG patch with upstream version to
add the tag flag them as upstreamed.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/18800
Signed-off-by: Robert Marko <robimarko@gmail.com>
Run 'make kernel_oldconfig' to get an up-to-date config.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/18800
Signed-off-by: Robert Marko <robimarko@gmail.com>
There are NAND IC-s that define 1-bit ECC as the minimal strength,
however that is unsupported by QPIC-SNAND as it only supports 4 or 8 bit
ECC.
Since most of these chips also support 4-bit ECC just fine, instead of
erroring out if 1-bit ECC is requested lets instead default to 4-bit ECC.
Fixes: 01b72ce61e ("qualcommax: ipq50xx: remove ECC user config from board files")
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18795
Signed-off-by: Robert Marko <robimarko@gmail.com>
It seems that kernel cleaned up its kernels so we need to include
<linux/of_platform.h> for of_platform_device_create().
Link: https://github.com/openwrt/openwrt/pull/18795
Signed-off-by: Robert Marko <robimarko@gmail.com>
Using devm_clk_get_enabled() allows simplification of the driver and
dropping of the .remove OP as well.
Link: https://github.com/openwrt/openwrt/pull/18795
Signed-off-by: Robert Marko <robimarko@gmail.com>
6.12 PWM core introduced a bunch of incompatible changes, namely removal
of manual module owner assignment, complete PWM struct allocation and usage
refactor, etc.
So, update the driver to follow other drivers in 6.12 so it compiles.
Link: https://github.com/openwrt/openwrt/pull/18795
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh kernel config by running kernel_menuconfig.
Manually enable CONFIG_HW_RANDOM and CONFIG_CRYPTO_DEV_QCOM_RNG as these
got somehow disabled by the refresh.
Link: https://github.com/openwrt/openwrt/pull/18795
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh 6.12 patches, those that failed automatic refresh were refreshed
manually.
DT bindings patches that failed were dropped as we dont use them in practice.
Link: https://github.com/openwrt/openwrt/pull/18795
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Link: https://github.com/openwrt/openwrt/pull/18795
Signed-off-by: Robert Marko <robimarko@gmail.com>
CONFIG_IDPF is Intel(R) Infrastructure Data Path Function Support and it
should be disabled by default, if needed it can be packaged as a kmod.
Disable to prevent spreading out through target configs.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Noticed that CONFIG_HISILICON_ERRATUM_162100801 was being added to
qualcommax 6.12 config.
Since we dont support any Hisilicon chips, disable it in generic config
before it starts spreading in target configs.
Signed-off-by: Robert Marko <robimarko@gmail.com>
DRM_ACCEL symbols were not added to geode and legacy thus making the kernel
prompt for them on compilation.
Fixes: 51b78aaaae ("kernel: package intel_vpu driver")
Signed-off-by: Robert Marko <robimarko@gmail.com>
RFC4541, section 2.1.2 says:
Packets with a destination IP (DIP) address in the 224.0.0.X range
which are not IGMP must be forwarded on all ports.
And section 3 says:
In IPv6, the data forwarding rules are more straight forward because
MLD is mandated for addresses with scope 2 (link-scope) or greater.
The only exception is the address FF02::1 which is the all hosts
link-scope address for which MLD messages are never sent. Packets
with the all hosts link-scope address should be forwarded on all
ports.
However, currently when a listener on FF12::1 or FF12:🔢0:1 for
example joins then not only packets to these addresses but also for
FF02::1 won't be flooded to all ports anymore, too. Which violates
RFC4541.
This happens because A): They all map to the same ethernet multicast
address, that is 33:33:00:00:00:01. And B) the VLAN profile L2
unknown MC flood setting will only apply flooding of 33:33:00:00:00:01
if there is no specific listener registered for it.
So to fix this, avoid registering an MDB entry in the switch for
33:33:00:00:00:01 at all.
The downside of this is that FF12::1, FF12:🔢0:1 etc.
will always be flooded, too. However fixing the handling of 224.0.0.X
and FF02::1 and adhering to RFC4541 must have priority to avoid
undesired packetloss, to avoid breaking IPv4/IPv6.
Tested-on: ZyXEL GS1900-24HP v1
Fixes: cde31976e3 ("realtek: Add support for Layer 2 Multicast")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Link: https://github.com/openwrt/openwrt/pull/18769
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove property 'status = "disabled"' for partitions in Zyxel NBG7815.
This option is mainly used for NAND memory and here we have SPI memory.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18787
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix "property has invalid length" warning for two devices:
- TP-Link EAP620 HD v1
- Zyxel NBG7815
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18787
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fixes the following warning:
[ 180.314652] NOHZ tick-stop error: local softirq work is pending, handler #08!!!
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Currently, non existing ipq-wifi package name is selected for
EAP625-Outdoor HD, so correct the name.
Fixes: 51c1ea08d0 ("qualcommax: ipq60xx: add TP-Link EAP625-Outdoor HD v1 support")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add package for linux intel_vpu driver for Intel NPU/VPU
Signed-off-by: Joe Zheng <joe.zheng@intel.com>
Link: https://github.com/openwrt/openwrt/pull/17904
Signed-off-by: Robert Marko <robimarko@gmail.com>
TP-Link EAP625-Outdoor HD is a 802.11ax AP claiming AX1800 support.
It is wall or pole mountable, and rated for outdoor use. It can only
be powered via PoE.
Hardware-wise, it is very similar to the older EAP610-Outdoor model.
Software-wise, I couldn't find a difference other than the board
data files, and device name. For this reason, the majority of the
devicetree from the EAP610-Outdoor is reused.
This device currently comes in a "v1", and "v1.6" version. The
"support-list" of the vendor firmware does not have a distinction
between these versions. This commit was tested on a 'V1.6" device.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512 MB
* Storage: 128MB NAND
* Ethernet:
* Gigabit RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Multi-color System LED (Green/Amber)
* Buttons:
* 1x Reset
* UART: 4-pin unpopulated header
* 1.8 V level, Pinout 1 - TX, 2 - RX, 3 - GND, 4 - 1.8V
Installation:
=============
Web UI method
-------------
Set up the device using the vendor's web UI. After that go to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
The connect to the machine via SSH:
ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>
Disable signature verification:
cliclientd stopcs
Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
* Go to System -> Firmware Update.
* Under "New Firmware File", click "Browse" and select the image
* Select "Update" and confirm by clicking "OK".
If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWRT.
NOTE: If ssh continues to complain that "no matching host key type
found. Their offer: ssh-rsa,ssh-dss" it likely means that yor distro
has completely disabled deprecated siphers in ssh. In that case, run
the ssh command from a docker container of an older distro.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot tplink_eap625-outdoor-hd-v1-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the commandline.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18584
Signed-off-by: Robert Marko <robimarko@gmail.com>
It was suggested that the pinctrl property of the mdio node should
include the PHY reset GPIO. Add them in.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18584
Signed-off-by: Robert Marko <robimarko@gmail.com>
I have an EAP625-Outdoor HD v1 that is very similar with the EAP610
Outdoor. It works with the EAP610 initramfs, without any obvious loss
of functionality. In order to prepare for supporting the EAP625, move
the common parts into a shared .dtsi.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18584
Signed-off-by: Robert Marko <robimarko@gmail.com>
The web-recovery of the Genexis EX400 validates uploaded images to fit
in the rootf_0 partition.
With OpenWrt, only the kernel is stored in this partition, leaving the
partition very small. Currently, the first factory release image won't
be accepted by the recovery interface after the OpenWrt installation.
Pad the image of the ubifs to 10MB. This allows the 24.10 release image
to be uploaded, enabling device recovery.
Signed-off-by: David Bauer <mail@david-bauer.net>
Clean the temporary directory the UBI image is generated from before
generation.
Currently it is removed after the image generation, which leads to files
possibly not being cleared after a build failure in this step.
Signed-off-by: David Bauer <mail@david-bauer.net>
bcm6328, bcm6362 and bcm6368 targets are missing a key config symbol which
prevents the NAND from working.
Fixes: f6c02b014d ("bmips: 6.1: refresh config and add missing symbols")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
CONFIG_PAHOLE_HAS_LANG_EXCLUDE is set depending on the pahole version
present, so it must be filtered out.
Signed-off-by: Robert Marko <robimarko@gmail.com>
For kernel 6.12 there is a warning causing an error:
drivers/mtd/nand/mtk_bmt_v2.c: In function 'mtk_bmt_get_mapping_mask':
drivers/mtd/nand/mtk_bmt_v2.c:307:31: error: 'kmalloc_array_noprof' sizes specified with 'sizeof' in the earlier argument and not in the later argument [-Werror=calloc-transposed-args]
307 | used = kcalloc(sizeof(unsigned long), BIT_WORD(bmtd.bmt_blk_idx) + 1, GFP_KERNEL);
| ^~~~~~~~
Swapping the arguments solves the problem.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18701
Signed-off-by: Robert Marko <robimarko@gmail.com>
Kernel does
if (phydev->drv->set_loopback)
ret = phydev->drv->set_loopback(phydev, enable, speed);
else
ret = genphy_loopback(phydev, enable, speed);
So no need to explicitly set genphy_loopback() in phy_driver. Drop
references to let kernel do its work.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18782
Signed-off-by: Robert Marko <robimarko@gmail.com>
PCI paths of IPQ50xx devices have changed now that linux,pci-domain is set
in the DTSI, so add a migration script for wireless config.
Link: https://github.com/openwrt/openwrt/pull/18789
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that IPQ50xx PCIe nodes have linux,pci-domain property defined
it changed the PCI path, but its now predictable and fixed.
So, update the caldata script accordingly.
Link: https://github.com/openwrt/openwrt/pull/18789
Signed-off-by: Robert Marko <robimarko@gmail.com>
Unlike other buses, for PCIe child nodes we should not use "wifi@1,0" as
the bus adress since for PCI devices the actual device adress on the bus is
actually set via the "reg" property and the node name is unused completely.
Though, it will cause DTC to throw warnings, so after investigation and
similar issue upstream[1] simply set the nodes to "wifi@0,0" instead.
[1] https://lists.infradead.org/pipermail/linux-arm-kernel/2021-August/680846.html
Link: https://github.com/openwrt/openwrt/pull/18789
Signed-off-by: Robert Marko <robimarko@gmail.com>
PCIe bridge nodes are now present in the SoC DTSI, so drop our downstream
ones as otherwise ath1*k BDF matching will fail.
Link: https://github.com/openwrt/openwrt/pull/18789
Signed-off-by: Robert Marko <robimarko@gmail.com>
It seems that bus-range property was missed for the PCIe bridges on
IPQ50xx, thus causing DTC to warn on any bus adress used on nodes
under the PCIe bridges.
Link: https://github.com/openwrt/openwrt/pull/18789
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the latest v9 PCIe DTS patch that is pending upstream, notable change
being that it includes PCIe bridge nodes.
Link: https://github.com/openwrt/openwrt/pull/18789
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add missing kmod-7915e package to get both wireless interfaces working.
Link: https://github.com/openwrt/openwrt/issues/18690
Reviewed-by: Steffen Förster <nemesis@chemnitz.freifunk.net>
Signed-off-by: Christoph Krapp <achterin@gmail.com>
We are lucky to have a working realtek environment. But some things where mixed
heavily. To say it clear a bus is a bus and an ethernet is an ethernet. With
the new naming conventions and defines this becomes even more obvious.
Decouple it by moving the bus specific parts out of the ethernet device. To
make the code more readable rename bus_priv variables to priv and sort variable
definitions in inverse tree order (length descending) where it makes sense.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18402
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
At least since 2022 there is a major bug in the MDIO driver that
produces out-of-bound reads and erratic behaviour during initialization.
- mdiobus_scan_bus_c22() scans the bus for 64 devices (PHY_MAX_ADDR)
- private bus structure only supports 57 entry arrays (MAX_PORTS)
All the bus/reader writer functions accept calls with addr>=57 and will
silently read beyond their limits. This can lead to ghost SERDES like
https://github.com/openwrt/openwrt/issues/18665#issuecomment-2846053813
Add proper boundary checks and end the functions with -ENODEV that is
the only accepted error code from the bus scan function.
Fixes: 0536c582e6 ("realtek: Fix RTL931X Ethernet driver") etc ...
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18402
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
These two arrays have been fixed to some sane size (= 64 ports). Now
that everything is in place reuse the global RTMDIO_MAX_PORT define.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18402
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Relocate the bus structure definition into the MDIO source code area
of the ethernet driver. So if the real bus driver is forked from the
rest of the code only one area needs to be removed. Rename it to make
clear it belongs to the bus.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18402
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Although a dfine is used to set the maxiumum number of SMI
busses (=4) it is not used at all appropriate places in the code.
Replace hard coded constants with that define.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18402
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Inside the ethernet driver lives the mdio bus. It is not always clear
what belongs where. Prefix some leftovers from the kernel 6.6 refactor
to clearly state what belongs to the bus. Group all defines together
in one place. This commit has no functional changes.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18402
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
IPQ9554 does not have uniphy1. The "gcc_uniphy1_sys_clk" cannot be
enabled. This causes the ipq-uniphy driver to crash on .probe().
Add a patch to resolve the crash.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18779
Signed-off-by: Robert Marko <robimarko@gmail.com>
Found when building rockchip target (with kernel 6.12).
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/18685
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit corrects led phy names. This has been discussed
at link [1] and corrected in the mediatek target in the
commit a51fd20e0d. Now it's time
to do the same thing in the lantiq target.
Link: https://github.com/openwrt/openwrt/pull/18265
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This is the same hardware as the Cudy WR2100 that's
had support for some time now, just without the WLAN
hardware.
This PR is mostly copied from the commit that added
support for the WR2100, here: 3501db9
Specifications:
SoC: MT7621
CPU: 880 MHz
Flash: 16 MiB
RAM: 128 MiB
Ethernet: 5x Gbit ports
Installation:
There are two known options:
The Luci-based UI.
Press and hold the reset button during power up.
The router will request 'recovery.bin' from a TFTP server at
192.168.1.88.
Both options require a signed firmware binary.
A signed firmware can be found in GitHub PR #18532.
R4 & R5 need to be shorted (0-100Ω) for the UART to work.
Link: https://github.com/openwrt/openwrt/pull/18532
Signed-off-by: David DeGraw <degraw@fastmail.com>
Configure the i2c pins as GPIO outputs and use the i2c-gpio driver to
control the Semtech SX9512 touch controller.
This fixes spurious errors in i2c transactions even at 1kHz with the
native i2c driver.
leds green:wan: Setting an LED's brightness failed (-6)
Signed-off-by: David Bauer <mail@david-bauer.net>
Add the necessary package dependencies as well as device-tree properties
to support the touch-inputs as well as missing LEDs on the Genexis Pulse
EX400 range extender.
Signed-off-by: David Bauer <mail@david-bauer.net>
This driver is required for the touch-inputs as well as some LEDs on the
Genexis Pulse EX400.
The driver was also sent upstream. As the EX400 is currently the only
consumer, the driver is added target-specific for ramips.
Once the driver has been accepted upstream and is provided in a kernel
release used by OpenWrt, the package should be moved to the global input
drivers.
Link: https://www.spinics.net/lists/kernel/msg5669349.html
Signed-off-by: David Bauer <mail@david-bauer.net>
There's no need for it. Kernel update to 6.12 found that it now needs
linux/of.h explicitly included.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18763
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specify 4-bit ECC strength instead of 8-bit, to resolve NAND I/O errors
on ELECOM WRC-X3000GS2.
ELECOM WRC-X3000GS2 has a Macronix MX35UF1G24AD SPI-NAND chip as a flash
storage. That chip is registered as a chip that has 128 bytes OOB and
requires 8-bit ECC, and described as the same in the Macronix's datasheet.
But on WRC-X3000GS2, 8-bit ECC breaks NAND I/O on mtdblock devices with
the following errors and 4-bit ECC needs to be used to resolve this issue.
current (ECC strength=8):
```
[ 1.401566] 0x000000480000-0x000000500000 : "0:appsblenv"
[ 1.407128] 1 fixed-partitions partitions found on MTD device 0:appsblenv
[ 1.410663] Creating 1 MTD partitions on "0:appsblenv":
[ 1.417359] 0x000000000000-0x000000040000 : "env-data"
[ 1.479865] u-boot-env-layout: probe of 79b0000.qpic-nand:flash@0:partitions:partition-0-appsblenv:partition@0:nvmem-layout failed with error -74
root@OpenWrt:~# strings /dev/mtdblock10
[ 55.693754] mtdblock: MTD device '0:appsblenv' is NAND, please consider using UBI block devices instead.
[ 55.694660] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 2
[ 55.703147] I/O error, dev mtdblock10, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 2
[ 55.711884] I/O error, dev mtdblock10, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 2
[ 55.720778] I/O error, dev mtdblock10, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[ 55.730310] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[ 55.738607] Buffer I/O error on dev mtdblock10, logical block 0, async page read
```
after fixing (ECC strength=4):
```
[ 1.402301] 0x000000480000-0x000000500000 : "0:appsblenv"
[ 1.407909] 1 fixed-partitions partitions found on MTD device 0:appsblenv
[ 1.411370] Creating 1 MTD partitions on "0:appsblenv":
[ 1.418075] 0x000000000000-0x000000040000 : "env-data"
(no error)
root@OpenWrt:~# strings /dev/mtdblock10
[ 39.131008] mtdblock: MTD device '0:appsblenv' is NAND, please consider using UBI block devices instead.
bootcmd=bootipq
baudrate=115200
wifi2=7C:F8:54:01:BD:F3
CRASH_COUNT=0
...
```
Fixes: 01b72ce61e ("qualcommax: ipq50xx: remove ECC user config from board files")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18770
Signed-off-by: Robert Marko <robimarko@gmail.com>
Include <linux/of.h> instead of <linux/of_device.h>.
This problem arised when adding support for 6.12, but it can be fixed on
older kernels too.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
kmod-drm-rp1-dsi, kmod-drm-rp1-dpi and kmod-drm-rp1-vec should depend on
kmod-drm-dma-helper and kmod-drm-vram-helper in order to fix dependency errors
when all kernel modules are selected.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
There are no supported devices on this sub-target. It can be
considered that it is still under development. Therefore,
there is no need to make the buildbot build it every day.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18757
Signed-off-by: Robert Marko <robimarko@gmail.com>
This problem arised when adding support for 6.12, but it should be fixed on
older kernels too.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
These drivers should include <linux/platform_device.h>, but this wasn't an
issue on kernels < 6.12.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This sub-target is source only now. We don't need to disable build
for specific devices.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18745
Signed-off-by: Robert Marko <robimarko@gmail.com>
Due to RAM/ROM size limitations, this sub-target has been unable
to generate usable images for a long time. Mark them as source-only
to save some resource for the buildbot.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18745
Signed-off-by: Robert Marko <robimarko@gmail.com>
This sub-target is source only now. We don't need to disable build
for specific devices.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18745
Signed-off-by: Robert Marko <robimarko@gmail.com>
Due to RAM/ROM size limitations, this sub-target has been unable
to generate usable images for a long time. Mark them as source-only
to save some resource for the buildbot.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18745
Signed-off-by: Robert Marko <robimarko@gmail.com>
This sub-target is source only now. We don't need to disable build
for specific devices.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18745
Signed-off-by: Robert Marko <robimarko@gmail.com>
Due to RAM/ROM size limitations, this sub-target has been unable
to generate usable images for a long time. Mark them as source-only
to save some resource for the buildbot.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18745
Signed-off-by: Robert Marko <robimarko@gmail.com>
The RTL8214FC currently uses generic PHY functions. That makes it look like a copper
device. Switching to/from fibre works fortunately but the autonegotiation handling
still works on MII_LPA (PHY register 5) as if a copper link is used. Fix that by
- advertising a superset of TP/FIBRE features
- using clause 37 functions when on fibre
Additionally enhance the code of the driver to assist further development.
- log the speed of the inserted module to detect wrongly inserted 10gbase-r modules
- order phy driver functions alphabetically (keep match/name on top)
- remove genphy_loopback as the kernel uses it if not provided
Remark! The driver internally uses PORT_MII for the TP port. Align with that and
report MII to ethtool instead of TP. Other drivers do the same and it can be
changed in the future if needed.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18724
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reduces boot time by 3s on a freshly installed image. This device
has a large flash and the gain can be higher with more packages
installed. According to the datasheet, this is the maximum frequency
supported by the Micron and Macronix chips that are installed in
these devices. Tested on three units over a two month period.
Before:
$ dd if=/dev/mtd5 of=/dev/null bs=10M count=1 status=progress
1+0 records in
1+0 records out
10485760 bytes (10 MB, 10 MiB) copied, 1.51901 s, 6.9 MB/s
After:
$ dd if=/dev/mtd5 of=/dev/null bs=10M count=1 status=progress
1+0 records in
1+0 records out
10485760 bytes (10 MB, 10 MiB) copied, 0.899474 s, 11.7 MB/s
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/18694
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mikrotik RouterBOARD 2011 series are AR9344-based wired routers, with
optional 2,4GHz 802.11n 2x2:2 Wi-Fi radio, with desktop or rack-mount
capability, featuring 5 gigabit Ethernet ports and 5 fast Ethernet
ports. Different variants of the board are supported using a single
image.
Bare-bones RouterBOARD 2011LS is supported using the same image.
Specification:
- Power: 10-28V input via 5,5/2,1 DC barrel jack, or terminal block on
some boards
- CPU: AR9344 at 600 to 750MHz (configurable)
- RAM: 128MB (64MB in early versions) DDR2
- Flash: 128MB (64MB in early versions) NAND flash
- Gigabit Ethernet: 5 ports via AR8327 switch (eth1 to eth5)
- Fast Ethernet: 5 ports via AR9344 built-in switch (eth6 to eth10)
- SFP: single port through AR8327 switch (SGMII at port 6)
- PoE in: passive input up to 28V at eth1
- PoE out: passive output up to 28V at eth10
- USB: optional micro-AB host port or type-A host port
- Console: optional Cisco-style RS232 console at the back of the device,
on budget devices available as 3.3V UART via testpoints
- LCD: 2" touchscreen-equipped LCD (unsupported)
Installation:
- perform TFTP boot of initramfs image as for netinstall procedure
typical for Mikrotik devices
- when initramfs image boots, use sysupgrade to perform final
installation.
If upgrading from ar71xx, clean installation should be performed, as the
devices now uses yafut to handle kernel image.
TODO:
- 64MB NAND variant using K9F1208U0C isn't yet supported, because it
needs disabling subpage write support for that chip. A proper solution
would be to fix that in kernel, but I don't have this variant to test
with currently.
- The same is true for GD9FU1G8F3A NAND, which isn't ONFI compliant and
needs definition in kernel for proper geometry.
- SFP port probes over I²C and gigabit link is possible, but currently
the drivers lack support of handling link status information to
userspace, including swconfig. Link will appear as always up.
Currently, link status logging can detect something, but status both
for ports 0 and 6 is logged simultaneously,
but "swconfig dev switch0 show" will always show link up on port 6.
- Not yet fully known connection to display and touch panel, but some
documentation is available (seemingly connected via SPI, according to
Mikrotik's open source code at [1])
[1] https://github.com/robimarko/routeros-GPL
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17617
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Passing QMP pipe clocks was upstreamed, but it requires conversion single
QMP node, so backport both of those instead of our downstream patch.
Signed-off-by: Robert Marko <robimarko@gmail.com>
In order to free up some more number space, simply renumber existing
upstreamed patches starting from 0 again.
Signed-off-by: Robert Marko <robimarko@gmail.com>
With the spi-qpic-snand driver now supporting reading ECC requirements
from the NAND chip itself, there's no need to set those in the DTS
anymore avoiding issues with devices of the same revision using
different NAND types with varying ECC requirements.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18723
Signed-off-by: Robert Marko <robimarko@gmail.com>
Updating the spi-qpic-snand driver with the latest patches sent
upstream and remove custom patches.
These patches add error handling fixes, use of right read location in
read ops, removal of unused variable, ability to read user config and
nand chip requirements, and support for 8bits ECC strength.
Tested on: Gl.iNet GL-B3000 & Linksys MR5500, MX2000, MX5500, SPNMX56
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18723
Signed-off-by: Robert Marko <robimarko@gmail.com>
Multiple conf support was upstreamed into kernel 6.10, so lets use the
upstreamed patches and mark them as so.
Signed-off-by: Robert Marko <robimarko@gmail.com>
MP5496 patches are not part of 6.15, but rather will be part of 6.16 as
they are no in 6.15 RC releases but they are in linux-next.
Signed-off-by: Robert Marko <robimarko@gmail.com>
When many multicast entries are installed broadcast flooding might
potentially stop working for several ports. This is because the layer
2 broadcast flood port mask index has the wrong offset. It should be
9 bits, matching the 2^9 = 512 indexes on rtl838x, not 12.
The wrong offset leads to L2_BC_FLD_PMSK being set to 504, not 511
((511 << 12) >> 9) & 511 = 504). So, as by default an unset PMSK
is set to all ports, the issue would only become noticeable once
many multicast entries are installed, causing the 504th entry to be set
to something other than all ports.
Fixing this by setting the offset to 9 bits, to correctly point to our
511th reserved entry for all ports.
Tested-on: ZyXEL GS1900-24HP v1
Fixes: 28e972b2ea ("realtek: Configure initial L2 learning setup")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Link: https://github.com/openwrt/openwrt/pull/18733
Signed-off-by: Robert Marko <robimarko@gmail.com>
This additional board.d script creates the "/tmp/sysinfo/oem_name" file
and populates it with the proper OEM "supported_devices" metadata entry
to be used by the new fwtool.sh oem detection feature.
(#18554): add oem image dectection to fwtool.sh
Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18656
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update block NVMEM driver based on backported OF partition support.
Note the different MMC card DT binding compared to the previous
downstream solution: Instead of having a 'partitions' subnode inside
a 'block' node, the 'partitions' node now resides directly under the
node representing the card.
In order to make references to the 'boot0' or 'boot1' hw partitions
you will have to define 'partitions-boot0' or 'partitions-boot1', and
move the NVMEM layout into a partition (you may, of course, use
'fixed-partitions' for that, and cover the whole device, if needed).
See also https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/mmc/mmc-card.yaml?h=v6.13
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add network config for single-port Gateworks venice boards such that the
ethernet port is the WAN port instead of the default being a LAN port.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/18629
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some DTS files have a qsgmii link mode for the CPU port. This does
not harm but it is wrong. The CPU port of the realtek switch is always
directly connected to the switch by some unknown wiring and should
therefore be described as internal. Align the wrongly defined DTS
files to the standard.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18691
Signed-off-by: Robert Marko <robimarko@gmail.com>
- Fix order of patches (3d483a10327f was merged before 34d5a86ff7bb).
- Reorganize patch numbers now that < 6.12 patches are no longer needed.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This patch was added on linux v6.13 in order to avoid simple is_visible
functions on hwmon drivers.
See 79bc0af904
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Upstream e2015942e90a couldn't be backported to 6.6 because the following
symbols were missing:
- disable_work
- disable_work_sync
- enable_work
See e2015942e9
Upstream 34e5ededf4b8 couldn't be backported to 6.6 because the following
symbol was missing:
- pcim_iomap_region
See 34e5ededf4
Reorganize patch numbers now that < 6.12 patches are no longer needed.
The following patches still differ from upstream:
- e340bff27e63
phy_set_eee_broken symbol is missing in 6.12
https://github.com/torvalds/linux/commit/e340bff27e63
The following patches can't be backported to 6.12 due to missing symbols:
- 5e7a74b6a357
phy_disable_eee_mode symbol is missing in 6.12
https://github.com/torvalds/linux/commit/5e7a74b6a357
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Commit d7e82c78d7 added a generic kernel patch that exposes a new
symbol REALTEK_PHY_HWMON when REALTEK_PHY and HWMON are enabled. The new
symbol was added to kmod-phy-realtek, but the kmod is not used in the
realtek target.
Fixes: d7e82c78d7 ("generic: backport Realtek PHY patches from upstream")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Avoids some pointless boilerplate.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18675
Signed-off-by: Robert Marko <robimarko@gmail.com>
This seems to be some manual patch editing or rebasing bug.
Found with grep ' '.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18675
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit 1c993da8ff.
VSC kmod is broken and is causing all targets to fail compiling so revert.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Probing of the RTL8214FC on RTL839x is currently very strange.
- On RTL8393 nothing is detected and only generic PHY is reported
- On RTL8392 the port 1 is not detected while port 2-4 seem to work
Someone left a special RTL8393 detection rules that seems to indicate
that the we probe the internal SerDes instead. That is not true. Since
upgrade to kernel 6.6 the RTL8218/RTL8214FC detection is 100% accurate
and probing functions are only called when really needed.
Fix the issue by removing the condition. For now do PHY patching only
on the RTL838x where it already worked before.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18671
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Removes the need for a remove function in platform_device.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18660
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Easy way to add compatibility for kernel 6.12.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18660
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix DTB warning when compiling an image by adding the missing hash sign
of adress-cells in the usb_dwc node.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18672
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit fc3ff2af0c introduced reading
ECC strength from the device tree. Linksys MR5500 uses the mx-base dtsi
which was originally developed for Linksys MX2000 and MX5500 where the
ECC strength is set to 8. Correct this and set it to strength of 4 as
per the NAND specs for Gigadevice GD5F2GQ5REYIH.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18672
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit 34e5bc4af54d366147a83904c094d54fec7fb025.
While fixing support for 2.5Gbps mode on uniphy in phy to phy link
setups, it inadvertently broke fixed link scenario. So let's revert this
commit until there's a fix that doesn't impact fixed links.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18668
Signed-off-by: Robert Marko <robimarko@gmail.com>
fixes the following warning seen in bootlog
"Kernel image misaligned at boot, please fix your bootloader!"
Fixes: 3307fe8 ("qualcommax: ipq50xx: add support for GL.iNET GL-B3000")
Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18658
Signed-off-by: Robert Marko <robimarko@gmail.com>
The factory image generation for the Genexis EX400 image currently fails
if CONFIG_TARGET_ROOTFS_INITRAMFS is disabled.
Create the factory image only if said config option is enabled to avoid
failing builds.
Signed-off-by: David Bauer <mail@david-bauer.net>
These symbols were found when adding 6.12 kernel support for the
ath79 target.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18653
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
These get dynamically set, not relevant for targets.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16547
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The x86 now supports 6.12 kernel as testing.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16547
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16547
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
These symbols only become visible when some packages or kernel debug
options get enabled. Move them to generic.
Co-authored-by: Mantas Pucka <mantas@8devices.com>
Co-authored-by: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16547
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refreshed patches for generic/hack-6.12 by running
make target/linux/refresh
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16547
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refreshed patches for generic/pending-6.12 by running
make target/linux/refresh
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16547
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move MIPS reloc patch from pending to hack and rework it to adapt to new
kernel 6.12 version.
This required an additional patch. While at it also improve the text
with the original info without cut.
Link: https://github.com/openwrt/openwrt/pull/16547
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refreshed patches for generic/backport-6.12 by running
make target/linux/refresh
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16547
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16547
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refreshed patches by running:
make target/linux/refresh
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18640
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix the resets of the GE_PHY and Uniphy found on the IPQ5018 SoC.
Bitmasks are used to perform multiple resets simultaneously, including
the RX and TX clocks. This enables the Uniphy to properly shift between
SGMII/1G and SGMII+/2.5G modes.
While at it, properly reorder the patches, and rename some to follow
naming standards.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18638
Signed-off-by: Robert Marko <robimarko@gmail.com>
Patch 620-net_sched-codel-do-not-defer-queue-length-update.patch is
actually an ancient patch that somehow manage to be ported for 7 solid
years.
This comes from [1] where a fix patch was proposed. Nobody notice that
the proposed patch was actually rejected upstream in favor of [2]. And
the upstream fix patch is present in kernel from version 4.18.
This means that we were actually fixing for a non existant bug and maybe
introducing regression down the line.
Drop the patch for good as we already have a fix for it in flace for a
long time.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=109581
[2] 35b42da69e
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
As part of the previous commit to add the #clock-cells property to the
GE PHY, the PHY was inadvertently moved under the second mdio node in
the dtsi, and therefore broke the init sequence as the driver was trying
to use the wrong mdio bus to set the init values (ex. DAC, MSE, and AZ).
So let's move it back under the right mdio node and, while at it, pad
the register addresses to 8 hex numbers and re-order properties in line
with Linux DTS coding standards.
Fixes: 6782d0e66f
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18634
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix swapped WLAN LEDs and move to blue LEDs to match stock behavior. Add LAN LED mappings.
Signed-off-by: Erik Servili <serverror@serverror.com>
Link: https://github.com/openwrt/openwrt/pull/18624
Signed-off-by: Robert Marko <robimarko@gmail.com>
Easy way to add compatibility for kernel 6.12.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18617
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop the firmware image entry "factory.ubi" from IMAGES for ELECOM
WRC-X3000GS2.
`Device/UbiFit` is added in the early stage of working for adding
support of the device, but finally, only `KERNEL_IN_UBI` is neccesary
and factory.ubi is not. So `Device/UbiFit` should have been replaced
to `KERNEL_IN_UBI` but it was forgotten.
Fixes: 3b7d72bc2e ("qualcommax: add support for ELECOM WRC-X3000GS2")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18611
Signed-off-by: Robert Marko <robimarko@gmail.com>
Hardware
--------
SOC: MediaTek MT7981b
RAM: 256MB DDR3
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7981b DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Installation
-----------------------------------------------------------
Vendor-UI Method
-----------------------------------------------------------
1. Download the OpenWrt initramfs.trx image.
2. Connect the PC via LAN to one of the yellow router ports and wait
until your PC to get a DHCP lease.
3. Browse to http://192.168.50.1
4. If your router is brand new, finish the setup process and log into
the Web-UI.
5. Navigate to Administration -> Firmware Upgrade and upload the
downloaded OpenWrt image.
6. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
-----------------------------------------------------------
TFTP Method
-----------------------------------------------------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.70/24. Rename the image to rtax52.bin.
2. Connect the PC with TFTP server to the RT-AX52.
Set a static ip on the ethernet interface of your PC.
(ip address: 192.168.1.70, subnet mask:255.255.255.0)
Conect to the serial console,
interrupt the autoboot process by pressing '4' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 rtax52.bin
$ bootm 0x46000000
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
---------------------------------------------------------------------------
Revert to stock firmware:
1: Download the rt-ax52 firmware from ASUS official website. Save
the firmware to tftp server directory and rename to RT-AX52.trx
2: Connect the PC with TFTP server to the RT-AX52.
Set a static ip on the ethernet interface of your PC.
(ip address: 192.168.1.70, subnet mask:255.255.255.0)
3: Conect to the serial console, power on again, interrupt the
autoboot process by pressing '4' when prompted.
$: ubi remove linux
$: ubi remove jffs2
$: ubi remove rootfs
$: ubi remove rootfs_data
$: ubi create linux 0x45fe000
$: reset
Then the dut will reboot,interrupt the autoboot process by
pressing '2' when prompted.
2: Load System code then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
$: enter y
you will see the follow, type enter directly:
Input device IP (192.168.1.1) ==:
Input server IP (192.168.1.70) ==:
Input Linux Kernel filename (RT-AX52.trx) ==:
4: wait for the device run up
Based on support for ASUS RT-AX52 by liudongdongdong7397
and trx image generation by remittor
Signed-off-by: Christoph Krapp <achterin@gmail.com>
This commit fixes mistaken executable bit on
mt7981b-mercusys-mr80x-v3.dts file.
Fixes: 7921e48d43 ("mediatek: add support for Mercusys MR80X v3")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Add missing semicolon to the end of the property.
Remove whitespace while at it.
Fixes: 5a3b9d88f1 ("lantiq: Improve support for LED's fritz736x")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/18594
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix nand-ecc-strength property in the spi-nand node of GL-iNet GL-B3000
to 4, to solve the following ECC error on that spi-nand chip.
[ 1.551618] ubi0: attaching mtd11
[ 1.552331] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 0:0, read only 64 bytes, retry
[ 1.554455] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 0:0, read only 64 bytes, retry
[ 1.565931] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 0:0, read only 64 bytes, retry
[ 1.576568] ubi0 error: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 0:0, read 64 bytes
[ 1.587146] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.6.87 #0
[ 1.597153] Hardware name: GL.iNet GL-B3000 (DT)
[ 1.602881] Call trace:
[ 1.607739] dump_backtrace+0xa0/0xe0
[ 1.609910] show_stack+0x18/0x24
[ 1.613728] dump_stack_lvl+0x48/0x60
[ 1.617027] dump_stack+0x18/0x24
[ 1.620672] ubi_io_read+0x11c/0x32c
[ 1.623972] ubi_io_read_ec_hdr+0x50/0x1f0
[ 1.627618] ubi_attach+0x35c/0x133c
[ 1.631524] ubi_attach_mtd_dev+0x494/0xaf4
[ 1.635257] ubi_init_attach+0xac/0x2e4
[ 1.639163] do_one_initcall+0x6c/0x1fc
[ 1.642983] kernel_init_freeable+0x204/0x2e4
[ 1.646803] kernel_init+0x28/0x1dc
[ 1.651316] ret_from_fork+0x10/0x20
The GL-B3000 has a Winbond W25N01GW and the spare size (oobsize) of it
is 64. So the maximum available ECC strength with the qpic-snand driver
is 4 but not 8.
The "nand-ecc-strength" property was not used before the commit
fc3ff2af0c ("qualcommax: allow overriding ECC strength for qpic-snand")
and calculated from the registered spare size in the Linux Kernel. As a
result, we had no issues on the GL-B3000 with the wrong ECC strength
value.
Fixes: 3307fe8ee4 ("qualcommax: ipq50xx: add support for GL.iNET GL-B3000")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18595
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specification:
- MT7620A 580 MHz MIPS24KEc
- 64MB RAM
- 8MB SPI NOR
- MediaTek MT7612E 5.0GHz 802.11a/n/ac
- MediaTek MT7620 2.4GHz 802.11b/g/n
- 5 LEDs (white)
- 1 button
- 1 Gbit port Realtek RTL8211E GbE Phy
Serial Interface:
- 3 Pins GND, RX, TX
- Settings: 57600, 8N1
Based on support from edimax_ew-7476rpc/edimax_ew-747x
and netgear_ex3700/netgear_ex3x00_ex61xx
Notes:
- ATM there is no known way to revert to stock firmware
Flash instruction:
The only known way to flash OpenWrt image is to use tftp in U-Boot, with the
aid of a serial adapter for U-Boot console access:
1. Open the device and connect to the serial port. The device is very similar
to Edimax 7476RPC. See https://openwrt.org/toh/edimax/ew-7476rpc. No VCC!
2. Configure PC with static IP 192.168.1.2/24 and tftp server and
connect PC to device using an ethernet cable.
3. Power on the device and, on the serial console, as soon as U-Boot starts
loading, press "2" to interrupt loading.
4. Enter device ip address 192.168.1.1, PC ip address 192.168.1.2
and the firmware filename placed on the TFTP server.
5. Device will download file from server, write it to flash and reboot.
Signed-off-by: Hugo Monteiro <monteiro.hugo@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16956
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ELECOM WRC-X3000GS2 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
IPQ5018.
Specification:
- SoC : Qualcomm IPQ5018
- RAM : DDR3 256 MiB (Zentel A3T2GF40CBF-HP)
- Flash : SPI-NAND 128 MiB (Macronix MX35UF1G24AD-Z4I)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm IPQ5018 (SoC)
- 5 GHz : Qualcomm Atheros QCN6102
- Ethernet : 5x 10/100/1000 Mbps
- wan (phy) : Qualcomm IPQ5018 (SoC)
- lan (switch) : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO): 8x/3x
- UART : through-hole on PCB, 4pins near the barcode
- assignment : 3.3V, TX, RX, NC, GND from the barcode side
- settings : 115200n8
- Power : 12 VDC, 1 A (Max. 11.5W)
Flash instruction using initramfs-factory.bin image:
1. Boot WRC-X3000GS2 normally with router mode
2. Access to the WebUI ("http://192.168.2.1/") on the device and open
the firmware update page ("ファームウェア更新")
3. Select the OpenWrt factory.bin image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing
Switching to the stock firmware:
1. Load the elecom.sh script
. /lib/upgrade/elecom.sh
2. Check the current index of rootfs
bootconfig_rw_index 0:bootconfig rootfs
3. Set the index to inverted value
bootconfig_rw_index 0:bootconfig rootfs <value>
bootconfig_rw_index 0:bootconfig1 rootfs <value>
example:
- step2 returned "0":
bootconfig_rw_index 0:bootconfig rootfs 1
bootconfig_rw_index 0:bootconfig1 rootfs 1
- step2 returned "1":
bootconfig_rw_index 0:bootconfig rootfs 0
bootconfig_rw_index 0:bootconfig1 rootfs 0
4. Reboot
Partition Layout (Stock FW):
0x000000000000-0x000000080000 : "0:SBL1"
0x000000080000-0x000000100000 : "0:MIBIB"
0x000000100000-0x000000140000 : "0:BOOTCONFIG"
0x000000140000-0x000000180000 : "0:BOOTCONFIG1"
0x000000180000-0x000000280000 : "0:QSEE"
0x000000280000-0x000000380000 : "0:QSEE_1"
0x000000380000-0x0000003c0000 : "0:DEVCFG"
0x0000003c0000-0x000000400000 : "0:DEVCFG_1"
0x000000400000-0x000000440000 : "0:CDT"
0x000000440000-0x000000480000 : "0:CDT_1"
0x000000480000-0x000000500000 : "0:APPSBLENV"
0x000000500000-0x000000640000 : "0:APPSBL"
0x000000640000-0x000000780000 : "0:APPSBL_1"
0x000000780000-0x000000880000 : "0:ART"
0x000000880000-0x000000900000 : "0:TRAINING"
0x000000900000-0x000003c40000 : "rootfs"
0x000003c40000-0x000003fc0000 : "Config"
0x000003fc0000-0x000007300000 : "rootfs_1"
0x000007300000-0x000007680000 : "Config_2"
0x000007680000-0x000007b80000 : "Reserved"
0x000007b80000-0x000007c00000 : "FWHEADER"
0x000007c00000-0x000007c80000 : "Factory"
Known Issues:
- All Wi-Fi related peripherals are disabled.
This device has only 256 MiB RAM and it's too few for ath11k. To
prevent OOM when using LuCI or other softwares, disable Wi-Fi related
peripherals in device tree at the moment.
- This device has a Macronix MX35UF1G24AD SPI-NAND chip registered as
oobsize=128 in Linux Kernel. But using BCH8 breaks I/O on the chip
with the following errors, so this support uses BCH4 instead.
root@OpenWrt:~# strings /dev/mtdblock10
[26427.133154] mtdblock: MTD device '0:appsblenv' is NAND, please consider using UBI block devices instead.
[26427.134125] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 2
[26427.142240] I/O error, dev mtdblock10, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 2
[26427.151427] I/O error, dev mtdblock10, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 2
[26427.160440] I/O error, dev mtdblock10, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[26427.169619] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[26427.178083] Buffer I/O error on dev mtdblock10, logical block 0, async page read
Notes:
- This device has dual-boot feature and it's managed by the index in the
0:bootconfig and 0:bootconfig1 partitions.
MAC Addresses:
LAN : 38:97:A4:xx:xx:60 (0:APPSBLENV, "eth1addr"/"ethaddr" (text))
WAN : 38:97:A4:xx:xx:63 (0:APPSBLENV, "eth0addr" (text))
2.4 GHz: 38:97:A4:xx:xx:61 (0:APPSBLENV, "wifi0" (text))
5 GHz : 38:97:A4:xx:xx:62 (0:APPSBLENV, "wifi1" (text))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18543
Signed-off-by: Robert Marko <robimarko@gmail.com>
Make the ECC strength in the qpic-snand driver configurable via device
tree to use the device-specific ECC strength value.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18543
Signed-off-by: Robert Marko <robimarko@gmail.com>
To further improve cleanup and maintenance usage, move the kernel
version files to target/linux/generic directory. This permits to self
contain any change to the specific generic directory instead of having
to bload the include directory of periodic changes.
In kernel-version.mk we now use GENERIC_PLATFORM_DIR provided by
target.mk. To make this work, we need to move the inclusion of
kernel-version.mk in target.mk right after GENERIC_PLATFORM_DIR is
defined.
This also comes to permit downstream project to provide a custom generic
directory and specify the kernel version complete of the hash and the
minor version without having to affect other feeds.
In such case both generic and the target directory are provided as feeds
and OpenWrt reference these specific one instead of the generic one.
For downstream it's still suggested and preferable to all match the
shipped generic kernel minor version but this change permits to at least
enforce good practice instead of having to bloat OpenWrt include file of
all kind of downstream changes (making porting to OpenWrt mainline even
more difficult)
Link: https://github.com/openwrt/openwrt/pull/18537
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The TP-link Deco X80-5G is a AX WIFI router with a single 1G (LAN) and 1 2.5G (WAN) port with a built in Quectel 5G modem.
Specifications:
Architecture ARMv8-A (aarch64 Cortex A53, 4 cores)
Vendor Qualcomm
Bootloader U-Boot (2016)
System-On-Chip Qualcomm IPQ8074A (Networking Pro 1210 platform)
CPU/Speed 2.2GHZ
Flash-Chip ESMT F59D1G81MB-45TI 1G-bit NAND
Flash MB 128MB (1Gbit)
RAM-chip 2* ESMT M15T4G16256A-DEBG2G 2Gb DDR3L (32bit)
RAM MB 512MB (4Gbit)
WLan System-On-Chip (5g) Qualcomm QCN5054
WLan Front end modules (5g) 8* Qorvo QPF4588
WLAN (5G) A/N/AC/AX
WLAN Antenna (int) 8* (4 shared with 2.5G)
WLan System-On-Chip (2.4G) Qualcomm QCN5024
WLan Front end modules (2.4G) 4* Skyworks SKY85340-11
WLAN (2.4G) B/G/N/AX
WLAN Antenna (int) 4* (shared with 5g)
Eithernet-phy (1Gbit) Qualcomm (Atheros) AR8033-AL1A
Ethernet (1Gbit) 1*
Eithernet-phy (2.5Gbit) Qualcomm QCA8081
Ethernet (2.5Gbit) 1*
Switch Embedded in the SOC?
Serial 1.8v 8n1 (testpoints)
Modem System-On-Chip Qualcomm 5G RG50xQ (Snapdragon X55 platform)
5G modem capability 5000Mbps down 900Mbps up
5G modem bands N1/N3/N5/N7/N8/N20/N28/N38/N40/N41/N77/N78/N79
4G modem capability 4.5G LTE-Advanced Pro (Cat20 down 2Gbps) (Cat18 up 200Mbps)
4G modem FDD bands B1/B3/B5/B7/B8/B18/B19/B20/B26/B28
4G modem TDD bands B34/B38/B39/B40/B41/B42/B43
Modem antenna (int) 8* (5G/4G use)
Modem antenna (ext) 2* SMA connectors (5G/4G use)
SIM type 1* Nano SIM
Telephony 1* POTS RJ11
(see wiki for more info:)
https://openwrt.org/inbox/toh/tp-link/x80-5g_v1
Notes:
Installation Instructions:
Between antennas 7 and 8 on the PCB with the RGB harness there are three test pads labelled TP1 TP2 and TP3 connections are as follows:
|TP2|-- RX
|TP1|-- TX
|TP3|-- GND
RX requires an external pullup to operate somewhere around 5 K ohm but your luck may vary the Uart is 1.8v
Set a static IP and set up a tftpserver and terminal.
power the router and quickly type the magic string “tpl” and press enter to break into u-boot
in the shell set the environment variables to enable tftp booting
setenv ipaddr (routerIP)
setenv serverip (server IP)
load you initramfs:
tftpboot 0x44000000 (serverIP):openwrt-qualcommax-ipq807x-tplink_x80-5g-initramfs-uImage.itb
boot your initramfs
bootm
upload your factory image to /tmp
format and install the factory image:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-qualcommax-ipq807x-tplink_x80-5g-squashfs-factory.ubi
Note as this device swaps root partitions upon update your boot partition may be set as mtd13
Update script to mount factory tplink partition's for MAC recovery and device data.
Capture Labelmac from Factory_data partition.
Patch LAN from Labelmac.
Patch ART from Labelmac.
Set GPIO to make modem operational from boot.
GPIO fan tables work like the stock device with three fan maps high active idle with a top fan speed of 6800 RPM.
High temp 70 deg speeds 6-8
Active temp 50 deg speeds 2-5
low temp 25 degree speed 0-1
Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/16329
Signed-off-by: Robert Marko <robimarko@gmail.com>
Patch script used for mounting of factory data partitions to not assume devices names or use hardcoded identifiers.
Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/16329
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch backport a fix for the SD card detection on NanoPi R6c/R6S
from upstream commit 95147bb42b
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18553
Signed-off-by: Robert Marko <robimarko@gmail.com>
Prevent flashing truncated or otherwise corrupted uImage.FIT images
by verifying checksums and hashes of all sub-images before flashing
using the newly packaged fit_check_sign tool.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add all boards using uImage.FIT to platform_check_image() case section
making sure we are dealing with a FIT image.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The board name that goes into /etc/board.json and is used by sysupgrade
for image verifications gets determined by the below command:
`strings /proc/device-tree/compatible | head -1`
as per package/base-files/files/lib/preinit/02_sysinfo
On more recent firmware version for the Pine64 RockPro64 v2.1 devices the
first entry is 'pine64,rockpro64-v2.1' however the metadata in the
sysupgrade image only specifies 'pine64,rockpro64' as supported and image
verification will fail.
This change makes it so the image metadata will contain both
'pine64,rockpro64' and 'pine64,rockpro64-v2.1' allowing image verification
to pass on both older and more recent firmware versions.
Signed-off-by: Sam Hegarty <hegarty.sam@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18542
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The IPQ5018 GE Phy driver registers two fixed rate clocks which are
passed on to the GCC which gatekeeps and passes them back to the phy.
Fix 'bad phandle' warning and tell consumer (GCC) how many cells to
expect when compiling.
Warning (clocks_property): /soc@0/clock-controller@1800000: Missing property '#clock-cells' in node /soc@0/mdio@88000/ethernet-phy@7 or bad phandle (referred from clocks[5])
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18548
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Xiaomi MiWiFi 3A wireless router has a similar system architecture as the Xiaomi Mi 4A router, which is already officially supported by OpenWrt.
Product website: https://www.mi.com/miwifi3a
Device specification
--------------------
SoC: MT7628AN MIPS_24KEc @ 580 MHz 2.4G-bgn 2x2
WiFi: MT7612EN 5G-an, ac 80 MHz 2T2R
Flash: 16 MB
DRAM: 64 MB
Switch: MT7628AN (integrated in SoC)
Ethernet: 1 x 10 /100 Mbps
USB: None
Antennas: 2 x 2,4 GHz and 2 x 5 GHz (all are external and non-detachable)
LEDs: blue/red/amber
Buttons: Reset
Serial: 115200,8n1
MAC addresses as verified by OEM firmware:
------------------------------------------
use address source
LAN *:DD factory 0x28
WAN *:DD factory 0x28
2g *:DE factory 0x4
5g *:DF factory 0x8004
OEM firmware uses VLAN's to create the network interface for WAN and LAN.
Bootloader info:
----------------
The stock bootloader uses a "Dual ROM Partition System".
OS1 is a deep copy of OS2.
The bootloader starts OS2 by default.
To force start OS1 it is needed to set "flag_try_sys2_failed=1".
How to install:
---------------
1- Use OpenWRTInvasion to gain Telnet, SSH and FTP access: https://github.com/acecilia/OpenWRTInvasion
[IP: 192.168.31.1 | Username: root | Password: root | FTP-Port: 21]
2- Connect to router using telnet or ssh.
3- Backup all partitions. Use command "dd if=/dev/mtd0 of=/tmp/mtd0". Copy /tmp/mtd0 to computer using ftp.
4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3a-squashfs-sysupgrade.bin to /tmp in router using ftp.
5- Enable UART access and change start image to OS1.
nvram set uart_en=1
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set flag_try_sys2_failed=1
nvram commit
6- Erase OS1 & OS2 and install OpenWrt
mtd erase OS1
mtd erase OS2
mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3a-squashfs-sysupgrade.bin OS1
Credits:
--------
This PR is based on the work of Zehao Zhang (Github: @ZZH-Finalize) that he had published in the PR: #15698
Signed-off-by: Olgun Demir <olgun.demir@mail.com.tr>
Link: https://github.com/openwrt/openwrt/pull/18427
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for GL.iNET (AX3000) B3000.
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Winbond W634GU6NQB-11 (512 MiB DDR3-933)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
* Wi-Fi: QCN6102 (2x2:2 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (3 Ports 10/100/1000 GBASE-T)
* Flash: Winbond W25N01GWZEIG (128 MiB)
* LEDs: 1x single-color blue LED (GPIO 24 Active High)
1x single-color white LED (GPIO 23 Active High)
* Buttons: 1x Reset (GPIO 27 Active Low)
Flash Instructions:
*** The .img files are now universal ! ***
Openwrt --> openwrt-qualcommax-ipq50xx-glinet_gl-b3000-squashfs-factory.img
GL.iNet OEM --> openwrt-b3000-4.5.18-0731-1722397535.img
Either file can be flashed, in any of the available upgrade options, in both Firmwares.
Pick a file .. pick a method .. and SEND IT !!
Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17903
Signed-off-by: Robert Marko <robimarko@gmail.com>
This adds the Thermal framework support for STM32MP157.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18119
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In modules.mk, sort packages in alphabetical order.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18119
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move kmod-phy-stm32-usbphyc in the "USB Support" menu and kmod-stm32-timers
in "Other modules" menu.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18119
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add STM32MP157C-DK2 support. This profile also supports the STM32MP157F-DK2
board. The only difference between these two boards is the CPU frequency
(650MHz for 157C and 800MHz for 157F).
A SCMI variant is available. With this variant the reset and clock
resources are provided by OP-TEE and the associated SCMI services.
It is the configuration recommended by STMicroelectronics, with secured
system resources.
The specifications bellow only list supported features.
Specifications
--------------
SOC: STM32MP157C
RAM: 512 MiB
Storage: SD Card
Ethernet: 1x 1 Gbps
Wireless: 2.4GHz Cypress CYW43455 (802.11b/g/n)
LEDs: Heartbeat (Blue)
USB: 4x 2.0 Type-A
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18119
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patch 87cb0446b7 also applies to higher kernel versions.
To apply to them it has been moved to a separate file in pending.
Fixes: 87cb0446b7 ("generic: fix broken TCP fraglist GRO patch")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18511
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix an error while building target/linux x64 on macOS 15.4 host,
due to the PATH_MAX macro being redefined:
mkdir -p /Volumes/test/openwrt/build_dir/target-x86_64_musl/linux-x86_64/linux-6.6.86/tools/objtool && make O=/Volumes/test/openwrt/build_dir/target-x86_64_musl/linux-x86_64/linux-6.6.86 subdir=tools/objtool --no-print-directory -C objtool
exec-cmd.c:15:9: error: 'PATH_MAX' macro redefined [-Werror,-Wmacro-redefined]
15 | #define PATH_MAX 4096
| ^
/Applications/Xcode.app/Contents/Developer/Platforms/MacOSX.platform/Developer/SDKs/MacOSX.sdk/usr/include/sys/syslimits.h:103:9: note: previous definition is here
103 | #define PATH_MAX 1024 /* max bytes in pathname */
| ^
exec-cmd.c is compiled as part of objtool to run on the host, and
therefore host headers are used, where PATH_MAX is already defined.
Using an old OpenWRT snapshot from 2025-02-16, where linux-6.6.77
used to build correctly, does not help. Reverting from Xcode 16.3 to
16.2 does not help either.
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18530
Signed-off-by: Robert Marko <robimarko@gmail.com>
The WL-WN573HX3 is an AX3000 outdoor Access Point by WAVLINK,
also sold in Europe as 7Links WLR-1300 (ZX-5612).
Specifications:
- MT7981B + MT7976 AX3000 2x2 DBDC (160 MHz)
- 16 MiB SPI NOR, 256 MiB RAM
- Gigabit ethernet port, 802.3af PoE
- IP67 outdoor case for wall or pole mounting with
four single band RP-SMA fiberglass antennas (8 dBi)
Installation:
- OEM Web UI is at 192.168.30.1 which will forward to
http://netlogin.link (using a captive portal)
- login with default password `admin`
- skip setup wizard by navigating directly to
http://netlogin.link/html/meshUpgrade.html
- upload WN573HX3-sysupgrade.bin
- reset to factory defaults to discard OEM UCI settings
MAC address assignment:
LAN 80:xx:xx:76:xx:25 hw 0x44e
WLAN 2.4G 80:xx:xx:76:xx:27 factory 0x04 (label MAC)
WLAN 5G 82:xx:xx:46:xx:27
pair key 8a:xx:xx:76:xx:27 also on label, not used by OpenWrt
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Specifications:
SoC: Mediatek MT7621AT (880 MHz MIPS dual-core, quad-thread, CPU)
512 Megabyte DDR3 SDRAM
32 Megabyte NOR Flash
4 Gigabit RJ45 PoE ports
2 MT7615N wifi chips (2.4GHz and 5GHz)
2 USB ports (1xUSB2 and 1xUSB3 - GL3510 chip)
RJ45 RS232 port on front panel (Max3232 chip)
2x mPCIe 2.0 slots for 4G/5G cards
2x SIM slot
1x SDCard Slot
Power via DC12V
4x Cell Antennae
4x Wifi Antennae
MAC Address Locations:
Purpose Ex. Partition Offset
2.4 Ghz *:01 factory 0x4
5 GHz *:02 factory 0x8004
LAN *:03 factory 0xe000
WAN *:04 factory 0xe006
MAC address prefix E4:3A:65 is registered to MofiNetwork Inc
and used as the prefix for all MAC addresses.
Manual: https://mofinetwork.com/files/MoFi_Network_MOFI5500_5GXeLTE_EM7690_SPECS.pdf
WiFi chip specs: https://www.mediatek.com/products/broadband-wifi/mt7615
CPU chip specs: https://www.mediatek.com/products/home-networking/mt7621
Teardown Pictures: https://fccid.io/2AE6X-MOFI5500/Internal-Photos/Internal-Photos-5591739
Installation:
Update Mofi 5500 to at least stock firmware version 4.8.6. (Available on the Mofi website.)
Previous versions are untested in the upgrade process. Log into the LuCI web interface,
usually at 192.168.10.1 and visit the 'System->Backup/Flash Firmware' page.
Upload and flash the firmware as usual.
Note to Maintainers: Do not remove SUPPORTED_DEVICES from the Makefile!
The customized Mofi version of OpenWRT (stock firmware) expects to see mofi5500 as the device
name. The stock firmware does not allow for forcing an installation.
Without this line, users cannot upload the new firmware through the stock Mofi firmware.
This device uses cell modems that could use QMI or MBIM.
Add LuCI Modem Manager to allow people to use these. Also, if they have
two cell network cards, ethernet, USB, or other kinds of networks, they may wish
to use MWAN3 to allow failover amongst their networks.
Please compile it with mwan3 for multiple WAN connections.
Co-authored-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Rick Mac Gillis <noreply@rickmacgillis.com>
Upstream version of ARM gc sections skip eeping some section. It was
reported some kernel load hang hence restore what we original did and
introduce a new patch that add the additional entry on top of the
upstream version.
Fixes: #18500
Fixes: 7843f21c51 ("generic: replace ARM gc sections patch with upstream version")
Tested-by: Stefan Kalscheuer <stefan@stklcode.de> (Turris Omnia)
Link: https://github.com/openwrt/openwrt/pull/18503
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Some regression were reported with the backported upstream version. Old
kernel require an additional flush in some case and this was handled in
the old downstream patch.
Reintroduce the flush to fix the regression and refresh affected patch.
Fixes: f63d64ede0 ("generic: move patch from pending to backport")
Link: https://github.com/openwrt/openwrt/pull/18501
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The ATS SFP GT-T quirk patch was backported to stable kernel 6.6 but
was not notice while bumping the kernel version as they listed the quirk
at the bottom of the SFP quirk table while our hack patch put it at the
top.
With migrating to the upstream version, the duplication was made more
apparent.
Drop the double entry for the SFP module as it's already there and not
needed and refresh patches.
Link: https://github.com/openwrt/openwrt/pull/18484
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop GC sections ARMv7 patch as the new upstream version already handle
it by disabling the config in the specific EFI boot stub driver.
Link: https://github.com/openwrt/openwrt/pull/18464
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace ARM gc sections patch with upstream version. It seems this
feature is finally supported upstream with some minor difference.
In theory the upstream version should cut even more stuff, this really
needs to be evaluated if it's OK also to handle regression with the
kernel 6.12 update.
Link: https://github.com/openwrt/openwrt/pull/18464
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace SFP ignore TX FAULT with upstream version by backporting the 2
related upstream patch. Refresh SFP affected patch.
Link: https://github.com/openwrt/openwrt/pull/18464
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Move all patch that got merged upstream from pending to backport and add
related tag. This is to make it easier to update to kernel 6.12.
Patch 680 required some special care as the upstream version had to be
split in a series of 6 patch.
Referesh all affected patch.
Link: https://github.com/openwrt/openwrt/pull/18464
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix execution of initramfs image on NEC Aterm devices by increasing
available memory for lzma extraction of lzma-loader.
The size of initramfs image of v24.10.0 exceeds available memory
(LZMA_TEXT_START - LOADADDR) and loader data running at LZMA_TEXT_START
will be overwritten by extracted data. As a result, LZMA extraction will
be broken and stuck (or unexpectedly reset).
Fix that issue by setting higher LZMA_TEXT_START address to increase
available memory for LZMA extraction by lzma-loader.
log (v24.10.0):
boot> tftpd
tftpd start 192.168.0.1
boot> start tftp load openwrt-24.10.0-ath79-generic-ne
end tftp load length = 6569768
start memory load ...
memory load complete
begin : 0x80040000
length : 6567044
startup: 0x80040000
boot> boot
begin : 0x80040000
length : 6567044
startup: 0x80040000
option: 0x0
NEC Aterm series (QCA9558)
Calibrating SGMII
SGMII cal value = 0xe
Configuring SGMII force mode
SGMII_CONFIG : 0x000000a2
MR_AN_CONTROL: 0x00008140
MR_AN_CONTROL: 0x00000140
OpenWrt kernel loader for AR7XXX/AR9XXX
Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org>
Decompressing kernel... [:<syntax:value>]');retu <--- (stuck)
IPL:SOFT-RESET <--- (reset by WDT)
memory test ... ok
flinstall OK
boot version: 1.0.0
...
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18476
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that all packages that relied on the skip mechanism are selected
via BUILD_DEVICES or by defaulting for the subtarget drop them from
individual DEVICE_PACKAGES so that Image Builder works again for armv7.
Fixes: #18411
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that all packages that relied on the skip mechanism are selected
via BUILD_DEVICES or by defaulting for the subtarget drop them from
individual DEVICE_PACKAGES so that Image Builder works again for armv8_64b.
Fixes: #18412
Link: https://github.com/openwrt/openwrt/pull/18462
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, bcm63xx-cfe is being installed into kernel build dir, however
that does not work for Image Builder as only certain artifacts from kernel
build dir are included in Image Builder.
So, simply install bcm63xx-cfe into image staging dir so its artifacts can
be used in Image Builder as well.
Fixes: #18408Fixes: #18409
Link: https://github.com/openwrt/openwrt/pull/18463
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Radxa ROCK 4SE[1] is a single board computer using the Rockchip
RK3399-T.
Hardware
--------
- Dual-core Cortex-A72 and quad-core Cortex-A53 CPU
- Mali-T860MP4 GPU
- LPDDR4 4GB RAM
- M.2 M Key slot (PCIe 2.1 x4)
- eMMC connector
- microSD card slot
- Wi-Fi 5 (not supported)
- Gigabit Ethernet with PoE support (additional PoE HAT required)
- USB 3.0 Type-A OTG port
- USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- USB Type-C power port (5V only)
- 40 Pin GPIO header
[1] https://radxa.com/products/rock4/4se
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to the micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/17554
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Radxa ROCK 4C+[1] is a single board computer with dual HDMI using
the Rockchip RK3399-T.
Hardware
--------
- Dual-core Cortex-A72 and quad-core Cortex-A53 CPU
- Mali-T860MP4 GPU
- LPDDR4 4GB RAM
- eMMC connector
- microSD card slot
- Wi-Fi 5 (not supported)
- Gigabit Ethernet with PoE support (additional PoE HAT required)
- USB 3.0 Type-A OTG port
- USB 3.0 Type-A HOST port
- 2x USB 2.0 Type-A HOST ports
- USB Type-C power port (5V only)
- 40 Pin GPIO header
[1] https://radxa.com/products/rock4/4cp
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to the micro SD card or
internal eMMC using dd.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/17554
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Mercusys MR80X(EU) v3 router.
Device specification:
- SoC: Mediatek MT7981b, Cortex-A53, 64-bit
- RAM: 512MB
- Flash: SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB)
- Ethernet: 4x 100/1000 Mbps LAN1,LAN2,LAN3 & WAN
- Wireless: 2.4GHz (802.11 b/g/n/ax)
- Wireless: 5GHz (802.11 a/n/ac/ax)
- LEDs: 1 orange and 1 green status LEDs, 4 green gpio-controlled LEDs
on ethernet ports
- Buttons: 1 (Reset)
- Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI
slots contain "seconduboot" (also U-Boot 2022.01-rc4)
Installation (UART):
- Place OpenWrt initramfs-kernel image on tftp server with IP 192.168.1.2
- Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'.
- Set the uboot environment for startup.
setenv tp_boot_idx 0; setenv bootcmd bootm 0x46000000; saveenv
If the bootarg is set to boot from ubi1, also change it to ubi0.
- Load and run OpenWrt initramfs image.
setenv serverip 192.168.1.2; setenv ipaddr 192.168.1.1; tftpboot initramfs-kernel.bin; bootm
- Browse IP 192.168.1.1, upload the 'sysupgrade' image and do upgrade.
Recovery:
- Press Reset button and power on the router.
- Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware.
Stock layout:
0x000000000000-0x000000200000 : "boot"
0x000000200000-0x000000300000 : "u-boot-env"
0x000000300000-0x000003500000 : "ubi0"
0x000003500000-0x000006700000 : "ubi1"
0x000006700000-0x000006f00000 : "userconfig"
0x000006f00000-0x000007300000 : "tp_data"
ubi0/ubi1 format:
U-Boot at boot checks that all volumes are in place:
+-------------------------------+
| Volume Name: uboot Vol ID: 0|
| Volume Name: kernel Vol ID: 1|
| Volume Name: rootfs Vol ID: 2|
+-------------------------------+
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| label | 94:0C:xx:xx:xx:12 | label |
| WAN | 94:0C:xx:xx:xx:13 | label+1 |
| LAN | 94:0C:xx:xx:xx:12 | label |
| WLAN 2g | 94:0C:xx:xx:xx:11 | label-1 |
| WLAN 5g | 94:0C:xx:xx:xx:10 | label-2 |
+---------+-------------------+-----------+
label MAC address was found in UBI partition "tp_data", file
"default-mac".
Signed-off-by: Schneider Azima <Schneider-Azima12@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/18181
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
USXGMII link-up may fail due to too short delay after PLL reset.
Increase the delay to fix this.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fixes to PCS driver to support 2.5G PHY
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Missing bus clock prevent access to NSSCC registers and thus it is
impossible change clock configuration, when ethernet connection speed
changes.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patches that fix:
* Wrong MSI interrups for PCIe3
* Hang during reboot due to stopped clocks
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
It seems new kernel version introduced -Wmissing-prototypes. This new
warning reported drivers that define non static function that are used
statically in the driver.
Fix this by declaring making those function actually static if not
defined in any header and not used outside of the single driver.
Co-authored-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18455
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
It seems new kernel linux version reorganized the header include and now
of.h needs to be explicitly included. This should have been done from
when the driver was introduced.
Add the missing of.h header to fix compilation error in later kernel
version.
Co-authored-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18455
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The reason phy fails to probe without explicitly overrided phy id is
that the reset timing fails to match. Fix it with proper `reset-delay-us` and
`reset-post-delay-us`.
While at it, change LED settings to match EAP610-Outdoor.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18450
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specification:
SoC: MediaTek MT7628AN
RAM: 128 MB, Zentel A3R1GE40JBF-8E
Flash: 16MB, Winbond W25Q128JV
Switch: rt3050-esw, 2 ports 100 Mbps
WiFi: MediaTek mt7628-wmac 2.4GHz 802.11n and MediaTek MT7663 5GHz
802.11ac (PCIe)
WWAN: Quectel EC200A-EL 4G modem (USB)
GPIO:
* 1 button (Reset/WPS)
* 6 LEDs (Power+WPS, LAN, 3xSignal)
* USB port power controls
* Modem reset
* Modem programming switch
* Internal/external antenna switch for 4G
Serial Interface:
TP10 - 3.3V can be used for level shifter, if needed
TP9 - TX
TP8 - RX
TP11 - GND
Interface properties: 115200, 8N1
Access to console using serial port for OEM firmware:
Username: admin
Password: 1234
Flashing via TFTP (no disassembling or soldering required):
1. Connect your PC and router to port LAN
2. Configure PC interface using static IP 192.168.1.225, mask
255.255.255.0
3. Place OpenWRT firmware image (*-squashfs-tftp-recovery.bin) to TFTP
root folder and renamed it to tp_recovery.bin
4. Unplug power from router
5. Press and hold Reset/WPS button
6. Power up the router
7. Wait until TFTP started uploading image (~10 seconds after power up)
and release Reset/WPS button
8. Wait until image uploaded, i.e. until LAN LED start lighting
9. Enable DHCP address on PC interface and wait for assigning address
10. Use ssh (root@192.168.1.1) to configure router properties
Depends on patch for firmware-utils package:
https://github.com/openwrt/firmware-utils/commit/2051fe5b
Signed-off-by: Sergii Shcherbakov <shchers@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17819
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: M16U4G16256A DDR4 512MB
Ethernet: 2x 2.5G + 3x 1G
USB: 1x USB 3.0
WiFi1: MT7975N 2.4GHz 4T4R
WiFi2: MT7975PN 5GHz 4T4R
Button: Reset, WPS
Power: DC 12V 2A
Flash instructions:
Connect to the router using ssh or telnet,
username: useradmin, password is the web
login password of the router.
Use scp to upload bl31-uboot.fip and flash:
"mtd write xxx-bl31-uboot.fip FIP"
"mtd erase ubi"
Connect to the router via the Lan port,
set a static ip of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
Download initramfs image, reboot router,
waiting for tftp recovery to complete.
After openwrt boots up, perform sysupgrade.
Note:
Back up all mtd partitions before flashing.
Signed-off-by: Yujie Zhu <libriunc@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18138
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CONFIG_QCOM_IPA kernel cofig was enabled by mistake and conflicts with
mac80211 as it indirectly selects QMI HELPERS. Backports project provid
his own version of QMI HELPERS hence it should not be built-in.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Make the RPM partition read-only. This was a mistake and a leftover from
staging branch but I can take this mistake as an excuse to document the
current problem with RPM.
It might happen that a board ship with a broken RPM .mbn, broken not in
the sense that the board doesn't boot or it's a brick but broken in the
sense that it's outdaed and suffer from a bug fixed in new version.
This bug consist in a problem with the regulators between USB and NSS.
The old RPM mess with the NSS regulator (l2) and change the voltage for
it while configuring the USB regulator (l5).
This cause the ethernet subsystem to malfunction with the port not
working.
To workaround this, it's needed to disable RPM handling and CPUFreq.
With these 2 disabled, the old RPM doesn't touch regulators and Ethernet
works correctly.
New RPM correctly handle regulators for USB (l5) and doesn't suffer from
this problem. A solution for this is getting discussed with QCOM hoping
to get some good feedback for it.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add pending patch fixing NSSCC boot stall. These patch are needed to
prevent the ICC to disable critical clock for NSSCC NOC.
Without these the system will stall and reboot with watchdog.
While at it also remove an extra clock from DTSI as it currently have no
use. Original patch is not modified to keep consistency with series
proposed upstream.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant comment in NSSCC clock patch. The problem has been
identified hence the comment doesn't apply anymore.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Define default partition table for SPI-NAND mounted on reference board.
This is where is normally placed the rootfs UBI.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh dts SPI-NAND patch to to v14. This is to keep stuff synced with
current pending patch revision and make it easier to replace patch
later (and discover something broke in the meantime)
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh the NSSCC patch for new PCIe patches. To keep track of fuzz
changes for the IPQ95xx patches, patch are not refreshed currently.
For the specific case of NSSCC patch, quilt gets confused and apply the
patch in the wrong node, putting it in the RPM node (causing all kind of
funny errors at runtime)
Correctly fix the patch to put the node right after the PCIe nodes.
Also the PORT patch need to be refreshed as the gpio header is added by
the PCIe patch.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add PCIe upstream patch and related nodes to enable PCIe on IPQ95xx.
Minimal change were required to backport the patch and apply on current
kernel. Refresh all affected patch.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add USB3 kmods to the default package list, USB3 correctly works on
IPQ95xx hence it can be enabled.
While at it drop the NSS-DP as it was added by mistake as the ethrnet
platform is handled differently on this SoC with pending upstream
drivers.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
QCOM SPI NAND driver got merged upstream hence we can drop the special
patch from qualcommax and qualcommbe target and move them to the generic
backports directory to reduce patch maintenance.
While at it refresh any affected patch and target and also backport other
minor fixup for the SPI NAND driver merged upstream later.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Adds latest 6.6 patches from the Raspberry Pi repository.
These patches were generated from:
https://github.com/raspberrypi/linux/commits/rpi-6.6.y/
With the following command:
git format-patch -N v6.6.85..HEAD
(HEAD -> bba53a117a4a5c29da892962332ff1605990e17a)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This brings up a serial console on the USB device port of
the DNS-313 by:
- Activating the usbgadget feature
- Selecting the usbgadget-acm package
- Adding an inittab that opens a console at ttyGS0 which is
the device side of ttyACMn of a connected host
Link: http://patchwork.ozlabs.org/project/openwrt/patch/20250403-dns313-usb-serial-v2-4-d84de8e86931@linaro.org/
Cc: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Sync jitterentropy source code with linux-6.12 to solve the
issue of jitterentropy initialization failed:
[ 9.523489] jitterentropy: Initialization failed with host not compliant with requirements: 9
[ 9.661916] kmodloader: 1 module could not be probed
[ 9.662377] kmodloader: - jitterentropy_rng - 0
In linux upstream commit cf27d9475f37 ("crypto: jitter - use
permanent health test storage"), when FIPS crypto is disabled,
the health test results are always explicitly skipped. That means
it will never return error code 9 (health test failed) again.
Fixes: https://github.com/openwrt/openwrt/issues/16684
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18399
Signed-off-by: Robert Marko <robimarko@gmail.com>
ath9k base starts at 512. This is a problem as it uses gpio_request_one
to request the GPIO, which is legacy API.
This upstream pending patch needs to also be ported to mac80211.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is only used by mach files, which are no longer used in OpenWrt.
Allows removing a custon ath9k_platform.h file.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
These only work with and are useful with mach files. Now that those are
gone, this can go too.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
* SoC: Qualcomm IPQ6018 (64-bit Quad-core Arm Cortex-A53 @ 1800MHz)
* Memory: 1 GiB
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCN9074 (4x4 5 GHz 802.11ax)
* Wi-Fi: IPQ6018 (4x4 2.4 GHz 802.11b/g/n/ax)
* Ethernet: RTL8211F (10/100/1GBASE-T)
* Flash: ESMT F59D1G81MB (128 MiB)
* LEDs: 1x Green Status (GPIO 37 Active High), 1x Yellow Status (GPIO 32
Active High) and an LED global control GPIO (GPIO 36 Active High, set
up by U-Boot)
* Buttons: 1x Reset (GPIO 9 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to the pads near T32 and T31.
2. Connect 3V3 TTL port to TX, RX, and GND, which are pad T31, T32 and
the pad near T31 respectively. Be sure not to connect VCC and
crossover TX and RX.
3. Copy RAM firmware image
openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-initramfs-uImage.itb
to TFTP server root, available at 192.168.0.1.
4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the
serial console (115200 baud) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# setenv serverip 192.168.0.1
# setenv ipaddr 192.168.0.99
# tftpboot 0x44000000 openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18389
Signed-off-by: Robert Marko <robimarko@gmail.com>
PHY2 led1 is configured to control PHY1's LED. Change it to PHY2.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18361
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adds support for setting bridge port learning and isolation flags on
ipq40xx.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/18375
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Bridge port isolation offload support has been added to the bridge core
and many DSA drivers. mt7530 support was backported in OpenWrt commit
c4e6a147a6 ("generic: 6.6: mt7530: add support for bridge port
isolation").
Backport qca8k support as well.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/18375
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This patch adds support for D-Link DGS-1210-26 rev. F1
Hardware specification
----------------------
* RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz
* 128MB DRAM
* 32MB NOR Flash (MX25L25635E)
* 24 x 10/100/1000BASE-T ports
* 2 x SFP ports
* Power LED
* Reset button on front panel
Installation using OEM webinterface
-----------------------------------
1. Make sure you are running OEM firmware from secondary slot. If not, switch to image2 using the menus
System > Firmware Information > Boot from image2
Tools > reboot
2. Upload image squashfs-factory_image1.bin via Tools > Backup / Upgrade Firmware > image1
3. Toggle startup image via System > Firmware Information > Boot from image1
4. Tools > reboot
Known working firmware version for this procedure: 6.20.007
Installation using TFTP and serial console
------------------------------------------
1. Prepare a TFTP server with the OpenWrt *initramfs-kernel.bin and assign it an IP from 10.90.90.0/24 (except 10.90.90.90)
2. Connect the TFTP server to one of switch's ports
3. Connect to the serial console (115200 baud) and power on the switch
4. Press the ESC key once you see "Hit Esc key to stop autoboot" in the console output
5. Press CTRL+C keys to get into the real U-Boot prompt
6. Init the network with the command "rtk network on"
7. Load the OpenWrt image with the command "tftpboot 0x8f000000 <TFTP_SERVER_IP>:<IMAGE_FILE>"
(<TFTP_SERVER_IP> is the TFTP server's IP, e.g. 10.90.90.100; <IMAGE_FILE> is the name of the image provided by the TFTP server)
8. Boot the OpenWrt image with the command "bootm"
9. Browse to https://192.168.1.1/cgi-bin/luci/admin/system/flash
10. Upload the the OpenWrt *squashfs-sysupgrade.bin to the switch
11. Wait for it to reboot
Signed-off-by: Christian Steiner <christian.steiner@outlook.de>
Link: https://github.com/openwrt/openwrt/pull/18378
Signed-off-by: Sander Vanheule <sander@svanheule.net>
NEC Aterm WG2200HP is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
QCA9558.
Specification:
- SoC : Qualcomm Atheros QCA9558
- RAM : DDR2 128 MiB (2x ESMT M14D5121632A)
- Flash : SPI-NOR 16 MiB (Macronix MX25L12835FM2I-10G)
- WLAN : 2.4/5 GHz
- 2.4 GHz : 3T3R (Qualcomm Atheros QCA9558 (SoC))
- 5 GHz : 4T4R (Qualcomm Atheros QCA9984)
- Ethernet : 5x 10/100/1000 Mbps
- switch : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO) : 12x/4x
- UART : through-hole on PCB
- assignment : 3.3V, GND, NC, TX, RX from tri-angle marking
- settings : 9600n8
- USB : 1x USB 2.0 Type-A
- Power : 12 VDC, 1.5 A (Max: 20 W)
- Stock OS : NetBSD based
Flash instruction using initramfs-factory.bin image:
1. Connect and open serial console
2. Power on WG2200HP and interrupt bootloader by ESC key
3. Login to the bootloader CLI with a password "chiron"
4. Start TFTP server by "tftpd" command
5. Upload initramfs-factory.bin via tftp from your computer
example (Windows): tftp -i 192.168.0.1 PUT initramfs-factory.bin
6. Boot initramfs image by "boot" command
7. On the initramfs image, back up the stock bootloader and firmware if
needed
8. Upload (or download) uboot.bin and sysupgrade.bin image to the device
9. Rplace the bootloader with a uboot.bin image
mtd write <uboot.bin image> bootloader
10. Perform sysupgrade with a sysupgrade.bin image
11. Wait ~120 seconds to complete flashing
Notes:
- All LEDs are connected to the Diodes PI4IOE5V9539LE I2C Expander chip.
(compatible with NXP PCA9539)
- The stock bootloader requires an unknown filesystem on firmware area
in the flash. Booting of OpenWrt from that filesystem cannot be
handled, so the bootloader needs to be replaced to mainline U-Boot
before OpenWrt installation.
- The data length of blocks in firmware image will be checked
(4M < threshold < 6M) on the stock WebUI of all versions, and
initramfs-factory.bin image of OpenWrt has the larger block data for
initramfs image. So that image cannot be applied to the stock WebUI
at all.
MAC addresses:
LAN : 98:F1:99:xx:xx:7C (config, 0x6 (hex))
WAN : 98:F1:99:xx:xx:7D (config, 0xc (hex))
2.4 GHz: 98:F1:99:xx:xx:7E (config, 0x0 (hex))
5 GHz : 98:F1:99:xx:xx:7F (config, 0x12 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17584
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add more DT labels and move a USB hub node to dts files of Aterm devices
as a preparation for adding support of Aterm WG2200HP.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17584
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This PR adds support for netis NX31 router.
Specification
-------------
- SoC : MediaTek MT7981BA dual-core ARM Cortex-A53 1.3 GHz
- RAM : 256 MiB DDR3
- Flash : SPI-NAND 128 MiB (ESMT)
- WLAN : MediaTek MT7976CN dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 2x2
- 5 GHz : a/n/ac/ax, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x3 (LAN, MediaTek MT7531AE)
10/100/1000 Mbps x1 (WAN, SoC internal phy)
- USB : No
- Buttons : Mesh, Reset
- LEDs : 1x Power (blue), unmanaged
1x Status (blue), gpio-controlled
1x WiFi 2.4 GHz (blue), gpio-controlled
1x WiFi 5 GHz (blue), gpio-controlled
3x LAN activity (blue), switch-controlled
1x WAN activity (blue), gpio-controlled
- Power : 12 VDC, 1 A
Installation
------------
1. Connect to the router using ssh (user: admin, pass: web interface
password)
2. Make mtd backup:
cat /dev/mtd0 | gzip -1 -c > /tmp/mtd0_spi0.0.bin.gz
cat /dev/mtd1 | gzip -1 -c > /tmp/mtd1_BL2.bin.gz
cat /dev/mtd2 | gzip -1 -c > /tmp/mtd2_u-boot-env.bin.gz
cat /dev/mtd3 | gzip -1 -c > /tmp/mtd3_Factory.bin.gz
cat /dev/mtd4 | gzip -1 -c > /tmp/mtd4_FIP.bin.gz
cat /dev/mtd5 | gzip -1 -c > /tmp/mtd5_ubi.bin.gz
3. Download mtd backup from the /tmp dir of the router to your PC using
scp protocol
4. Upload OpenWrt 'bl31-uboot.fip', 'preloader.bin' images to the /tmp
dir of the router using scp protocol
5. Write FIP and BL2 (replace bootloader):
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-bl31-uboot.fip FIP
mtd write /tmp/openwrt-mediatek-filogic-netis_nx31-preloader.bin BL2
6. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
7. Erase 'ubi' partition and reboot the router:
mtd erase ubi
reboot
8. U-Boot automatically boot OpenWrt recovery image from tftp server to
the RAM
9. Upload OpenWrt 'sysupgrade.itb' image to the /tmp dir of the router
(IP: 192.168.1.1) using scp protocol
10. Connect to the router using ssh and run:
sysupgrade -n openwrt-mediatek-filogic-netis_nx31-squashfs-sysupgrade.itb
Return to stock
---------------
1. Unpack stock BL2 and FIP partitions backup
2. Upload stock BL2 and FIP partitions backup to the /tmp dir of the
router using scp protocol
3. Connect to the router using ssh and run:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd unlock BL2
mtd unlock FIP
4. Restore backup:
mtd write /tmp/mtd4_FIP.bin FIP
mtd write /tmp/mtd1_BL2.bin BL2
5. Erase ubi and reboot:
mtd erase ubi
reboot
6. Power off the router
7. Press Reset button and power on the router. Release the button after
~10 sec
8. Navigate to U-Boot recovery web server (http://192.168.1.1/) and
upload the OEM firmware
Recovery
--------
1. Place OpenWrt
'openwrt-mediatek-filogic-netis_nx31-initramfs-recovery.itb' image on
the tftp server (IP: 192.168.1.254)
2. Press “Reset” button and power on the router. After ~10 sec release
the button.
3. Use OpenWrt initramfs system for recovery
MAC addresses
-------------
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| LAN | dc:xx:xx:d1:xx:18 | label |
| WAN | dc:xx:xx:d1:xx:1a | label+2 |
| WLAN 2g | de:xx:xx:11:xx:19 | |
| WLAN 5g | de:xx:xx:71:xx:19 | |
+---------+-------------------+-----------+
The LAN MAC was found in 'Factory', 0x1fef20
The WAN MAC was found in 'Factory', 0x1fef26
The WLAN 2g/5g MAC prototype was found in 'Factory', 0x4
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18324
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
**Huasifei WH3000 eMMC / Fudy MT3000**
Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC.
MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ
**Specifications**
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: eMMC 8GB
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
Two buttons: power/reset and mode (BTN_0)
LEDS: blue, red, blue+red=pink
UART: 3.3V, TX, RX, GND / 115200 8N1
**Installation via U-Boot rescue**
1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1
2. Connect to the WAN port and hold the reset button while booting the device.
3. Wait for the LED to blink 5 times, and release the reset button.
4. Open U-boot web page on your browser at http://192.168.1.1
5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
6. Wait for the router to flash the new firmware.
7. Wait for the router to reboot itself.
**Installation via sysupgrade**
Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings.
**Installation via SSH**
Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command:
```
sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-emmc-squashfs-sysupgrade.bin
```
**Factory MAC**
You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4`
```
dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C
```
**Enlarging a partition**
Though device has 8GB eMMC, it uses only 2GB `/dev/mmcblck0p6` as `rootfs` for `/rom` and `/overlay` leaving `/dev/mmcblck0p7` as empty unused space.
```
sgdisk -p /dev/mmcblk0
```
```
Disk /dev/mmcblk0: 15269888 sectors, 7.3 GiB
Sector size (logical/physical): 512/512 bytes
Disk identifier (GUID): 2BD17853-102B-4500-AA1A-8A21D4D7984D
Partition table holds up to 128 entries
Main partition table begins at sector 2 and ends at sector 33
First usable sector is 34, last usable sector is 14942174
Partitions will be aligned on 1024-sector boundaries
Total free space is 11197 sectors (5.5 MiB)
Number Start (sector) End (sector) Size Code Name
1 8192 9215 512.0 KiB 8300 u-boot-env
2 9216 13311 2.0 MiB 8300 factory
3 13312 21503 4.0 MiB 8300 fip
4 21504 29695 4.0 MiB 8300 config
5 29696 62463 16.0 MiB 8300 kernel
6 62464 4256767 2.0 GiB 8300 rootfs
7 4257792 14940159 5.1 GiB 8300
```
You can fix that by loading into `initramfs-kernel`, deleting empty `mmcblck0p7` partition and resizing `mmcblck0p6`
```
sysupgrade -F /tmp/openwrt-initramfs-kernel.bin
```
Install and run cfdisk
```
opkg update && opkg install cfdisk
cfdisk /dev/mmcblck0
```
- Select `mmcblck0p7` -> Delete
- Select `mmcblck0p6` -> Resize -> Write -> yes -> Quit
You will not see any difference in `cat /proc/partitions` after that but just flash a `sysupgrade` and you'll get the whole 7.3GB space for the `/overlay`.
Co-developed-by: hecatae <horus.ra@gmail.com>
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18220
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently, building at91 subtargets via image builder will fail as the
required built at91bootstrap is not present in the image builder at all
since its presumed to be in the binary directory which obviously does not
exist yet.
So, lets install the at91bootstrap binary into image staging directory and
use that instead
Link: https://github.com/openwrt/openwrt/pull/18414
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, building at91 subtargets via image builder will fail as the
required built u-boot is not present in the image builder at all since its
presumed to be in the binary directory which obviously does not exist yet.
So, lets install the u-boot binary into image staging directory and use
that instead.
Link: https://github.com/openwrt/openwrt/pull/18414
Signed-off-by: Robert Marko <robimarko@gmail.com>
Netgear WAX610 / WAX610Y is a 802.11ax AP claiming AX1800 support.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512MB
* Storage: Winbond W29N01HZBINF 128MB NAND
* Ethernet:
* 2.5GbE RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Power: Dual-color LED (Green / Orange), Single-color LED (Blue)
* Ethernet: Dual-color LED (Green / Orange)
* 2.4Ghz WiFi: 2x Single-color LED (Blue, Green)
* 5Ghz WiFi: 2x Single-color LED (Blue, Green)
* Buttons:
* 1x Reset
* UART: 4-pin populated header
* Pinout 1 - VCC, 2 - GND, 3 - TX, 4 - RX
Installation:
=============
Web UI method
-------------
Set up the device using the stock web UI in local management mode.
Download the ui-factory.tar image.
* Enter the Management tab
* Select Maintenance->Upgrade->Firmware Upgrade
* Ensure the "Upgrade Options" field has "Local" selected
* Click "Browse File" and select the image
* Click "Upgrade" (NOT "Upgrade Now") at the bottom of the page
The device will install the image but reboot back into the vendor
firmware. Return the to Firmware Upgrade page as above and select
"Boot up Backup Firmware". The device should reboot into OpenWRT.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot netgear_wax610-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the command line.
Signed-off-by: Erik Servili <serverror@serverror.com>
Link: https://github.com/openwrt/openwrt/pull/18377
Signed-off-by: Robert Marko <robimarko@gmail.com>
The built-in watchdog is redundant when the device has an external
GPIO based hardware watchdog. And there is a conflict that both of
them will attempt to register the same device entry in sysfs. This
resulted in the built-in watchdog being unable to be activated.
This patch explicitly disables the built-in watchdog for devices
that use GPIO watchdog to fix the error:
[ 1.779206] ath79-wdt 18060008.wdt: unable to register misc device, err=-16
[ 1.786355] ath79-wdt: probe of 18060008.wdt failed with error -16
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18395
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, kmod-usb-ohci,kmod-at91-udc and kmod-usb-gadget-eth are included
as the default packages for all at91 subtargets.
However, this is breaking image builder as kmod-at91-udc is not being built
on sama7 since it depends on USB_SUPPORT and sama7 does not have USB support
enabled in the kernel as its not supported upstream so its not even
selectable in the config.
So, move to include these as default packages only for sama5 and sama9x as
both of those have USB support enabled.
Fixes: #18407
Link: https://github.com/openwrt/openwrt/pull/18413
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
- SoC: Broadcom BCM63168 dual 400MHz MIPS
- Flash: 128MB NAND ESMT F59L1G81A
- RAM: 128MB DDR3
- Ethernet: 5x 1000M
- Wifi: BCM435F
- 1x USB 2.0 port
- 2x Button
- 11x LED
- Coax HPNA (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
The booloader will only install signed firmware so the image has to
be manually flashed.
- Set up a TFTP server on 192.168.1.0/24 to serve the initramfs image
- Interrupt the bootloader and run from RAM with
r 192.168.1.100:openwrt-bmips-bcm63268-actiontec_t1200h-initramfs.elf
- On the openwrt console, copy the wfi image using wget/tftp/scp, i.e
scp user@192.168.1.100:~/openwrt/bin/targets/bmips/bcm63268/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin /tmp/
- Erase half the flash partition where openwrt will be installed with
flash_erase -j /dev/mtd1 0 491
- Flash the openwrt image with
nandwrite -p /dev/mtd1 /tmp/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin
- Reboot
- Interrupt the bootloader again and use the c command to boot from
previous firmware if vendor image is loaded
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[Minor improvements to DTS file]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Convert the property variable type of "qcom,coexist-support" from
u32 to u8 to match the definition in the dt-bindings document.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18393
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, network ports using PHYs get a link, but there is no traffic.
Make it work again by moving the MAC config to phylink_mac_link_up.
A similiar change has been previously applied for RTL83xx in commit
cd958d945b ("realtek: 6.6: refactor mac config and link up for
RTL83xx").
Fixes: https://github.com/openwrt/openwrt/issues/17010
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18268
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The generic target configuration activates the
CONFIG_LEDS_CLASS_MULTICOLOR option. Do not deactivate it for the stm32
target.
Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/17277
[Reword commit message]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This restores sysupgrade support
Since OpenWrt 23.05, the firmware selector no longer provides sysupgrade
images for RE450 V1 & V2 and RE355 v1 due to image size constraints
(~5.7MB limit), making the generic build unusable.
This commit moves RE450 V1 & V2 to the tiny target, enabling:
- Smaller image builds within the flash size limit.
- Restored sysupgrade support via the firmware selector.
- A secure-by-default wireless setup while allowing full management via UCI.
- Officially supported images, reducing the need for custom (potentially insecure) builds.
This ensures users can install a functional OpenWrt build without compromising security defaults.
Signed-off-by: Ivan Diaz <diaz.it@icloud.com>
[Squashed the commits together and just copied the target definition
from the generic subtarget.]
Link: https://github.com/openwrt/openwrt/pull/18126
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
SoC: MediaTek MT7628AN
RAM: 128M DDR2, ESMT M14D128168A (2Y)
Flash: 32M, cFeon EN25QH256A (Dual Boot on OEM, concatenated on OpenWrt,
SPI)
Switch: MediaTek MT7628AN, 3 ports 100 Mbps
WiFi: MediaTek MT7628AN 2.4 GHz 802.11n
USB: 1 port USB 2.0
GPIO: 1 button (Wi-Fi & Reset on OEM, Reset on OpenWrt), 3 LEDs (Power,
Internet, Wi-Fi), USB port power controls
Disassembly:
There are 2 screws at the bottom near the LEDs hidden by rubber mounts.
After removing the screws, pry the gray plastic part around (it is secured
with latches) and remove it.
UART Interface:
The UART interface can be connected to the 5 pin located between LAN
ports and the WAN one.
Pins (from the second LAN port to the WAN one): VCC, TX, RX, NC, GND
Settings: 115200, 8N1
Flashing via TFTP:
1. Connect your PC and router to the first LAN port, configure PC
interface using IP 192.168.1.2, mask 255.255.255.0
2. Serve the firmware image (for OpenWrt it is *-squashfs-factory.bin)
renamed to KN-1221_recovery.bin via TFTP
3. Power up the router while pressing Wi-Fi button
4. Release Wi-Fi button when Power LED starts blinking
To revert back to OEM firmware:
The return to the OEM firmware is carried out by using the methods
described above with the help of the appropriate firmware image found on
osvault.keenetic.net.
When using OEM bootloader, the firmware image size cannot exceed the size
of one OEM «Firmware_x» partition or Kernel + rootFS size.
Signed-off-by: Ivan Davydov <lotigara@lotigara.ru>
Link: https://github.com/openwrt/openwrt/pull/18164
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
After booting, a "transmit queue 0 timed out" warning followed by a
register dump was observed. The dump indicates that mtk_hw_init() does
not initialize the EEECR during probe. This occurs because the
netdev is allocated in mtk_add_mac(), which is called after
mtk_hw_init(). Consequently, the EEECR register remains uninitialized
until a reset is triggered, causing mtk_hw_init() to run again with a
valid netdev, at which point the register is finally set.
To address this, instead of modifying the probe sequence, latch the Tx
LPI enable state and timer value, and move the EEECR register
initialization to mtk_mac_link_up() to ensure proper setup when the
interface comes up.
Additionally, the splat reveals that LPI functionality is controlled by
the MAC_MCR_EEE bits in the MCR register. Update mtk_set_eee() to
modify these bits accordingly.
Fixes: d8315d5358 ("kernel: backport Mediatek SoC EEE support")
Fixes: edddbaf79c ("kernel: Mediatek: set default EEE Tx LPI timer")
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Only force compat_version to 1.2 if it was less than 1.2 before, as changes
1.1 and 1.2 were bootloader-related and a completed boot indicates that the
changes have been completed. Newer compat version 1.3 indicates a config change
and should not be forced on boot.
Fixes: 84fc59c0d5 ("mediatek: filogic: bpi-r3: set netdev-name for sfp1 port")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Patches 751-03 and 751-04 as a result of commit 6407ef8d2b
were incorrectly placed in the backport folder.
So they return to their proper place.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18253
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add 'ubootmod' variant for the ASUS ZenWiFi BT8.
An out-of-tree installer will be provided in Github to allow users an easy
transition from the stock loader to OpenWrt's bootchain which is built from
source.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Break out all flash-layout dependent parts from device tree into separate
dtsi file to be used by both, stock layout and upcoming ubootmod variant.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware
--------
MediaTek MT7988D SoC (3x Cortex-A73 @1.8 GHz max)
1GB DDR4 RAM
128MB SPI-NAND (Winbond)
MediaTek MT7996 BE14000 Tri-Band Wi-Fi 7
3x LAN (2x 1GE MT7988 built-in, 1x 2.5GE MaxLinear GPY211C)
1x WAN (2.5GE MT7988 built-in)
LED: RGB PWM (supported as 3x PWM LED)
USB: 1x USB 3
Buttons: RESET, WPS
UART: 115200 8N1 3.3V
Installation
------------
1. Hold down RESET button and power on the device until
LED pulses red.
2. Assign IP 192.168.1.70/24 to your computer's Ethernet port
3. Connect Ethernet to one of the 1GE LAN ports
4. Open browser and visit http://192.168.1.1
5. Upload openwrt-mediatek-filogic-asus_zenwifi-bt8-factory.bin
6. Once OpenWrt initramfs system comes up, do sysupgrade using
openwrt-mediatek-filogic-asus_zenwifi-bt8-squashfs-sysupgrade.bin
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In case a broken fit image is present on flash the fitblk driver would
not map any /dev/fit* devices, but also not always close the block device
the image resides on. In case of ubiblock devices this is fatal as one
then cannot remove the ubiblock device (-EBUSY), and hence cannot replace
the broken image.
Always close the block device in case no sub-image was mapped.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Codename: Divo
Hardware specification:
========
SoC: Qualcomm IPQ6018
RAM: 512MB (2x ESMT 256MB DDR3L M15T2G16128A–DEBG2R)
NAND Flash: 512MB (Macronix MX30UF4G18AC or SK Hynix H27S4G8F2EDA-BC)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C-B0)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4@20/40/160 MHz (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 2x2@20/40/80 MHz (Qualcomm QCN5052 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 2x2@20/40 MHz (Qualcomm QCN5022 + Skyworks SKY8340-11)
IoT: Bluetooth 5 (CSR8811) - not implemented
LED: 1x RGB status + USB Blue (PWM)
USB: 1x USB 3.0
Button: WPS, Reset
Flash instructions (Without Serial):
========
Open Linksys Web UI - http://192.168.1.1/ca or http://linksysxxxxx.lan/ca depending on your setup.
xxxxx is the last 5 digits from the SN found on a sticker under the device.
Click on the Linksys Logo to by-pass smart app registration.
Login with your admin password. The default password can be found on the same sticker.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
Flash instructions (With Serial):
========
1. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd13 0 0
- nandwrite -p /dev/mtd13 openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd15 0 0
- nandwrite -p /dev/mtd15 openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin alt_kernel
2. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq60xx-linksys_mr7500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware:
- mtd -e kernel -n write FW_MR7500_1.1.12.211919_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MR7500_1.1.12.211919_prod.img alt_kernel
4. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq60xx-linksys_mr7500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
AQR firmware:
========
0. Firmware extracting:
To extract the firmware, use unblob (unblob.org)
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
2. Firmware updating:
Newer firmware (AQR114C.cld) is available in the latest OEM firmware (https://downloads.linksys.com/support/assets/firmware/FW_MR7500_1.1.12.211919_prod.img).
Copy AQR114C.cld to /lib/firmware/marvell
Link: openwrt#17428
Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko@gmail.com>
ipq60xx series MR devices share some common attributes such as LED for
USB port.
Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko@gmail.com>
Linksys MR7500 features 4x QSGMII QCA8075 and 1x USXGMII (1/2.5/5 GbE)
Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko@gmail.com>
Create factory tar for EAP620 HD v1 and EAP660 HD v1 which is accepted by the stock UI.
Fix bug in ipq807x and ipq60xx makefiles so TPLINK_SUPPORT_STRING is handled properly.
Modify tplink-mkimage-2022 script and relevant makefiles to allow spaces in support strings (required for EAP620 HD v1 and EAP660 HD v1).
Installation steps are identical to EAP610-Outdoor:
Web UI method
-------------
Set up the device using the vendor's web UI. After that go to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
The connect to the machine via SSH:
ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>
Disable signature verification:
cliclientd stopcs
Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
* Go to System -> Firmware Update.
* Under "New Firmware File", click "Browse" and select the image
* Select "Update" and confirm by clicking "OK".
If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWRT.
Signed-off-by: Shymon Samsel <ssamsel@umass.edu>
Link: https://github.com/openwrt/openwrt/pull/18340
Signed-off-by: Robert Marko <robimarko@gmail.com>
Move "# CONFIG_NVMEM_LAYOUT_ASCII_ENV is not set" to the correct location.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18335
Signed-off-by: Nick Hainke <vincent@systemli.org>
RNDIS interface name change from usb0 to eth1
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18298
Signed-off-by: Robert Marko <robimarko@gmail.com>
Using the pending ascii-eq-delim-env4 driver is a better way to read mac addresses since no
extra config is required
The change is like eacc4d8c9b, except for using smem for devinfo
thanks to @musashino205 for pointing out the simplification that removes
the extra partition
Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18186
Signed-off-by: Robert Marko <robimarko@gmail.com>
arcadyan_mozart was incorrectly placed below asus devices
Signed-off-by: Christoph Krapp <achterin@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18331
Signed-off-by: Robert Marko <robimarko@gmail.com>
Create factory tar for WAX620 and WAX630 which is accepted by the stock UI.
Must use 'Boot up Backup Firmware' button on stock upgrade page after install and reboot to swap partitions.
Signed-off-by: Erik Servili <serverror@serverror.com>
Link: https://github.com/openwrt/openwrt/pull/18334
Signed-off-by: Robert Marko <robimarko@gmail.com>
`bootargs = "console=ttyS0,57600";` is already defined on all
ramips target SoCs' dtsi. We don't need to override it with the
same value.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/18303
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
SoC: Qualcomm IPQ6000
RAM: 512 MiB
Flash: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: 2.4GHz 802.11b/g/n/ax 2x2
WLAN2: 5GHz 802.11a/n/ac/ax 2x2
Button: Reset, Switch
USB: 1x 3.0
SD slot: 1 in GL-AXT1800
Install via stock firmware:
Upload factory.bin in stock firmware's upgrade page,
do not preserve settings.
Install via uboot web failsafe:
Push the reset button for 5 seconds, then use broswer
to access http://192.168.1.1, and upload factory.ubi.
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
Make cpufreq work on different IPQ60xx SoC.
Also rebase ipq6018-cp-cpu.dtsi for mp5496.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh device tree, remove the useless sdhc2 aliases.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is the minimal change for the upcoming patches.
Refresh the device tree of ipq807x at the same time.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
Because of the dt-bindings error, these patches have not
been merged yet, and the driver part is fine.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
This can be used by GL.iNet devices from other target.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove a stray '|' character from 01_leds which has accidentally
been added.
Reported-by: Chukun Pan <amadeus@jmu.edu.cn>
Fixes: 63d56af6c6 ("mediatek: filogic: migrate Netgate N60 to upstream PHY LED control")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Other than GPIO LEDs, PHY LEDs do have an address.
Fix node names such that all gpio-leds do *not* contain an '@' sign and
PHY leds which do have an address also do contain the '@' sign.
This is done to prevent more copy&paste'ry of non-complaint DT
fragments.
Fixes: 7cbe34170e ("mediatek: add support for the GL.iNet GL-MT3000")
Fixes: fe10f97439 ("filogic: add support for GL.iNet GL-MT6000")
Fixes: e8f7597317 ("mediatek: filogic: add support for Cudy RE3000 v1")
Fixes: c9cb6411c1 ("mediatek: add support for Cudy WR3000 v1")
Fixes: 7560af7647 ("mediatek: filogic: migrate ASUS TUF AX6000 to upstream PHY LED control")
Fixes: 25ea7ff393 ("mediatek: filogic: migrate Acer W6/W6d to upstream PHY LED control")
Fixes: d50d51d74e ("mediatek: filogic: migrate Zyxel NWA50AX Pro to upstream PHY LED control")
Fixes: b88de5d507 ("mediatek: filogic: migrate Zyxel EX5700 to upstream PHY LED control")
Fixes: 63d56af6c6 ("mediatek: filogic: migrate Netgate N60 to upstream PHY LED control")
Fixes: fd76a38190 ("mediatek: filogic: migrate SmartRG Bonanza to upstream PHY LED control")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All devices have already been migrated to the upstream PHY LED
API. This prevents users from adding new devices using this hack.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
According to the MT7620A hardware datasheet, GPIO/14 was originally used for RIN of UARTF, but is now used as the WPS LED.
Corrected pinctrl to ensure it works properly in the future.
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18278
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add switch LED definitions for TP-Link TL-WR1043ND family, based on data
extracted from ar71xx board file. Update the LED labels to match current
pattern, i.e. drop the "tp-link:" prefix.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Attaching PHY driver to the switch, while adding LEDs binding causes the
PHY driver to create additional LED instances, handled incorrectly by
the PHY driver, which are non-functional. Use fixed-link to attach the
switch driver, instead of PHY driver, to prevent that.
This has a side effect of not logging switch port up/down events in the kernel
log.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add switch LED definitions for TP-Link Archer C7 v1/2/3 family, based on data
extracted from ar71xx board file. Update the LED labels to match current
pattern, i.e. drop the "tp-link:" prefix.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Attaching PHY driver to the switch, while adding LEDs binding causes the
PHY driver to create additional LED instances, handled incorrectly by
the PHY driver, which are non-functional. Use fixed-link to attach the
switch driver, instead of PHY driver, to prevent that.
This has a side effect of not logging switch port up/down events in the kernel
log.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add switch LED definitions for TP-Link TL-WDR4300 family, based on data
extracted from ar71xx board file. Update the LED labels to match current
pattern, i.e. drop the "tp-link:" prefix.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Attaching PHY driver to the switch, while adding LEDs binding causes the
PHY driver to create additional LED instances, handled incorrectly by
the PHY driver, which are non-functional. Use fixed-link to attach the
switch driver, instead of PHY driver, to prevent that.
This has a side effect of not logging switch port up/down events in the kernel
log.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The ar8216 switch driver supports exposing configuration of AR8327 and
AR8337 switch LEDs to the userspace, however it is only configurable
through platform data, causing the devices ported from ar71xx target to
lack the support.
Since there is still a long way to go until we can migrate the target to
qca8k, an interim solution is needed.
Extend ar8327_hw_config_of function to parse a "leds"
subnode, which will populate the missing platform data based on device
tree contents, and restore the existing support for the LEDs.
Standard bindings apply, mapping "reg" property to LED index, with
addition of "qca,led-mode" property, which selects HW (0) or SW (1)
mode, defaulting to HW mode.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Switch LEDs configured as active-low remain low instead of high upon
initialization, because in ar8327_leds_init, no distinction is made with
regards to LED pattern based on active_low property - only whether HW
mode is active. Select the proper initial pattern based also on
active_low to fix that.
While at that, simplify the equation ruling pattern selection for
setting brightness, avoiding unnecessary binary XOR operation, not
really valid for 'bool' type.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/12487
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Devices with chipidea usb controller does not detect usb hub after
phy-names change to "usb", revert it back to "usb-phy"
Fixes: 787cb9d87e ("ath79: change phy-names to only usb")
Signed-off-by: Simonas Tamošaitis <simsasss@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18230
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add missing LEDs and modem control for ASUS 4G-AX56
- wifi2.4G white
- wifi5G white
- wan two-coloured, white and red
- modem four-coloured white, blue, yellow and red
change
label = "xxxx:modem";
to
color = <LED_COLOR_ID_xxxx>;
function = LED_FUNCTION_MOBILE;
- rssi-1 white
- rssi-2 white
- rssi-3 white
and modem reboot and reset
Combined into one commit
Signed-off-by: Henrik Ginstmark <henrik@ginstmark.se>
Link: https://github.com/openwrt/openwrt/pull/17927
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With upstream changes hitting kernel 6.4 the dtb for u7623 ends up with
both mac (gmac) disabled, since this is now the default status in
mt7623.dtsi. Fix this by including mt7623a.dtsi (which already has all
necessary bits) and enabling all revlevant ports. This will also do
a side hustle of assigning proper clocks for power controller and
specifying proper power domain for few devices.
Link: https://lore.kernel.org/all/20230210182505.24597-1-arinc.unal@arinc9.com
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250304164507.60511-2-tmn505@terefe.re/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since 24.10.0, eth0, used for the WAN interface, does not work. From dmesg:
...
[ 1.831126] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 1.846204] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 19
...
[ 1.933969] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 1.967668] mt7530-mdio mdio-bus:1f: configuring for fixed/rgmii link mode
[ 1.975999] mt7530-mdio mdio-bus:1f eth0 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7530 PHY] (irq=21)
[ 1.986907] mt7530-mdio mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 1.987149] mtk_soc_eth 1e100000.ethernet eth0: error -17 registering interface eth0
[ 2.004157] mt7530-mdio mdio-bus:1f eth1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=22)
[ 2.017698] mtk_soc_eth 1e100000.ethernet eth0: entered promiscuous mode
[ 2.024849] DSA: tree 0 setup
...
[ 4.249680] mtk_soc_eth 1e100000.ethernet dsa: renamed from eth0
...
Like #15865, it seems that gmac0 does not rename eth0 to dsa until after the
switch ports are initialized, leading to a name collision (error -17 = EEXIST).
This patch follows #17062 by using openwrt,netdev-name to fix the collision.
Signed-off-by: J. S. Seldenthuis <jseldenthuis@lely.com>
Link: https://github.com/openwrt/openwrt/pull/18082
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds a default network configuration for the
Supermicro SuperServer SYS-E302-9D by adding all
onboard network ports to the default `lan` interface.
The network ports `eth0` till `eth3` use the `igb`
driver, whereas `eth4` till `eth7` use `i40e`.
--- Hardware Highlights ---
CPU: Intel Xeon D-2123IT, 2.20GHz, 4 cores
RAM: Up to 256GB in 4 DIMM Slots
Ports: 4x 1GbE, 2x 10GBase-T, 2x 10G SFP+, 1x IPMI 2.0
Video: 1x VGA
USB: 2x 3.0
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/17990
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Using board definition file extracted from stock firmware yields 50%
throughput improvement in RX direction under iperf3 test.
Make the device use temporary files from firmware_qca-wireless.git
temporarily, as well as select the specific variant in the device tree
files. The device uses same board file as the MF286C.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17620
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ZTE MF286 is an indoor LTE category 12 CPE router with simultaneous
dual-band 802.11ac plus 802.11n Wi-Fi radios and quad-port gigabit
Ethernet switch, FXS and external USB 2.0 port.
Software-wise it's compatible with previous MF286A, save for different
5GHz Wi-Fi board definition file, requiring a separate image.
Hardware highlights:
- CPU: QCA9563 SoC at 775MHz,
- RAM: 128MB DDR2,
- NOR Flash: MX25L1606E 2MB SPI Flash, for U-boot only,
- NAND Flash: W25N01GV 128MB SPI NAND-Flash, for all other data,
- Wi-Fi 5GHz: QCA9886 2x2 MIMO 802.11ac Wave2 radio,
- WI-Fi 2.4GHz: QCA9563 3x3 MIMO 802.11n radio,
- Switch: QCA8337v2 4-port gigabit Ethernet, with single SGMII CPU port,
- WWAN: MDM9250-based category 12 internal LTE modem
in extended mini-PCIE form factor, with 5 internal antennas and
2 external antenna connections, single mini-SIM slot.
- FXS: one external ATA port (handled entirely by modem part) with two
physical connections in parallel,
- USB: Single external USB 2.0 port,
- Switches: power switch, WPS, Wi-Fi and reset buttons,
- LEDs: Wi-Fi, Test (internal). Rest of LEDs (Phone, WWAN, Battery,
Signal state) handled entirely by modem. 4 link status LEDs handled by
the switch on the backside.
- Label MAC device: eth0
Internal modem of MF286C is supported via uqmi.
Console connection: connector X2 is the console port, with the following
pinout, starting from pin 1, which is the topmost pin when the board is
upright:
- VCC (3.3V). Do not use unless you need to source power for the
converer from it.
- TX
- RX
- GND
Default port configuration in U-boot as well as in stock firmware is
115200-8-N-1.
Installation:
Due to different flash layout from stock firmware, sysupgrade from
within stock firmware is impossible, despite it's based on QSDK which
itself is based on OpenWrt.
STEP 0: Stock firmware update:
As installing OpenWrt cuts you off from official firmware updates for
the modem part, it is recommended to update the stock firmware to latest
ath79: support ZTE MF286C
STEP 1: Booting initramfs image:
Method 1: using serial console (RECOMMENDED):
- Have TFTP server running, exposing the OpenWrt initramfs image, and
set your computer's IP address as 192.168.0.22. This is the default
expected by U-boot. You may wish to change that, and alter later
commands accordingly.
- Connect the serial console if you haven't done so already,
- Interrupt boot sequence by pressing any key in U-boot when prompted
- Use the following commands to boot OpenWrt initramfs through TFTP:
setenv serverip 192.168.0.22
setenv ipaddr 192.168.0.1
tftpboot 0x81000000 openwrt-ath79-nand-zte_mf286c-initramfs-kernel.bin
bootm 0x81000000
(Replace server IP and router IP as needed). There is no emergency
TFTP boot sequence triggered by buttons, contrary to MF283+.
- When OpenWrt initramfs finishes booting, proceed to actual
installation.
STEP 2: Backing up original software:
As the stock firmware may be customized by the carrier and is not
officially available in the Internet, IT IS IMPERATIVE to back up the
stock firmware, if you ever plan to returning to stock firmware.
It is highly recommended to perform backup using both methods, to avoid
hassle of reassembling firmware images in future, if a restore is
needed.
Method 1: after booting OpenWrt initramfs image via TFTP:
- Connect your USB-UART adapter
- Dump stock firmware located on stock kernel and ubi partitions:
ssh root@192.168.1.1: cat /dev/mtd9 > mtd3_ubiconcat0.bin
ssh root@192.168.1.1: cat /dev/mtd4 > mtd4_kernel.bin
ssh root@192.168.1.1: cat /dev/mtd9 > mtd5_ubiconcat1.bin
And keep them in a safe place, should a restore be needed in future.
Method 2: using stock firmware:
- Connect an external USB drive formatted with FAT or ext4 to the USB
port.
- The drive will be auto-mounted to /var/usb_disk
- Check the flash layout of the device:
cat /proc/mtd
It should show the following:
mtd0: 000a0000 00010000 "u-boot"
mtd1: 00020000 00010000 "u-boot-env"
mtd2: 00140000 00010000 "reserved1"
mtd3: 000a0000 00020000 "fota-flag"
mtd4: 00080000 00020000 "art"
mtd5: 00080000 00020000 "mac"
mtd6: 000c0000 00020000 "reserved2"
mtd7: 00400000 00020000 "cfg-param"
mtd8: 00400000 00020000 "log"
mtd9: 000a0000 00020000 "oops"
mtd10: 00500000 00020000 "reserved3"
mtd11: 00800000 00020000 "web"
mtd12: 00300000 00020000 "kernel"
mtd13: 01a00000 00020000 "rootfs"
mtd14: 01900000 00020000 "data"
mtd15: 03200000 00020000 "fota"
mtd16: 01d00000 00020000 "firmware"
Differences might indicate that this is NOT a MF286C device but
one of other variants.
- Copy over all MTD partitions, for example by executing the following:
for i in 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15; do cat /dev/mtd$i > \
/var/usb_disk/mtd$i; done
"Firmware" partition can be skipped, it is a concatenation
of "kernel" and "rootfs".
- If the count of MTD partitions is different, this might indicate that
this is not a MF286C device, but one of its other variants.
- (optionally) rename the files according to MTD partition names from
/proc/mtd
- Unmount the filesystem:
umount /var/usb_disk; sync
and then remove the drive.
- Store the files in safe place if you ever plan to return to stock
firmware. This is especially important, because stock firmware for
this device is not available officially, and is usually customized by
the mobile providers.
STEP 3: Actual installation:
- Set your computer IP to 192.168.1.22/24
- scp the sysupgrade image to the device:
scp -O openwrt-ath79-nand-zte_mf286a-squashfs-sysupgrade.bin \
root@192.168.1.1:/tmp/
- ssh into the device and execute sysupgrade:
sysupgrade -n /tmp/openwrt-ath79-nand-zte_mf286a-squashfs-sysupgrade.bin
- Wait for router to reboot to full OpenWrt.
STEP 4: WAN connection establishment
Since the router is equipped with LTE modem as its main WAN interface, it
might be useful to connect to the Internet right away after
installation. To do so, please put the following entries in
/etc/config/network, replacing the specific configuration entries with
one needed for your ISP:
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
option auth '<auth>' # As required, usually 'none'
option pincode '<pin>' # If required by SIM
option apn '<apn>' # As required by ISP
option pdptype '<pdp>' # Typically 'ipv4', or 'ipv4v6' or 'ipv6'
For example, the following works for most polish ISPs
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
option auth 'none'
option apn 'internet'
option pdptype 'ipv4'
The required minimum is:
config interface 'wan'
option proto 'qmi'
option device '/dev/cdc-wdm0'
In this case, the modem will use last configured APN from stock
firmware - this should work out of the box, unless your SIM requires
PIN which can't be switched off.
If you have build with LuCI, installing luci-proto-qmi helps with this
task.
Restoring the stock firmware:
- Boot to initramfs as in step 3:
- Completely detach ubi0 partition using ubidetach /dev/ubi0_0
- Copy over the stock kernel image using scp to /tmp
- Erase kernel and restore stock kernel:
(scp mtd4_kernel.bin root@192.168.1.1:/tmp/)
mtd write kernel /tmp/mtd4_kernel.bin
rm /tmp/mtd4_kernel.bin
- Copy over the stock partition backups one-by-one using scp to /tmp, and
restore them individually. Otherwise you might run out of space in
tmpfs:
(scp -O mtd3_ubiconcat0.bin root@192.168.1.1:/tmp/)
mtd write ubiconcat0 /tmp/mtd3_ubiconcat0.bin
rm /tmp/mtd3_ubiconcat0.bin
(scp -O mtd5_ubiconcat1.bin root@192.168.1.1:/tmp/)
mtd write ubiconcat1 /tmp/mtd5_ubiconcat1.bin
rm /tmp/mtd5_ubiconcat1.bin
- If the write was correct, force a device reboot with
reboot -f
Quirks and known issues
- It was observed, that CH340-based USB-UART converters output garbage
during U-boot phase of system boot. At least CP2102 is known to work
properly.
- Kernel partition size is increased to 4MB compared to stock 3MB, to
accomodate future kernel updates - at this moment OpenWrt 5.10 kernel
image is at 2.5MB which is dangerously close to the limit. This has no
effect on booting the system - but keep that in mind when reassembling
an image to restore stock firmware.
- uqmi seems to be unable to change APN manually, so please use the one
you used before in stock firmware first. If you need to change it,
please use protocok '3g' to establish connection once, or use the
following command to change APN (and optionally IP type) manually:
echo -ne 'AT+CGDCONT=1,"IP","<apn>' > /dev/ttyUSB0
- The only usable LED as a "system LED" is the blue debug LED hidden
inside the case. All other LEDs are controlled by modem, on which the
router part has some influence only on Wi-Fi LED.
- GPIO5 used for modem reset is a suicide switch, causing a hardware
reset of whole board, not only the modem. It is attached to
gpio-restart driver, to restart the modem on reboot as well, to ensure
QMI connectivity after reboot, which tends to fail otherwise.
- Modem, as in MF283+, exposes root shell over ADB - while not needed
for OpenWrt operation at all - have fun lurking around.
The same modem module is used as in older MF286.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17620
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Using board definition file extracted from stock firmware yields 50%
throughput improvement in RX direction under iperf3 test.
Make the device use temporary files from firmware_qca-wireless.git
temporarily, as well as select the specific variant in the device tree
files.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17620
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently, if the phy driver does not implement the led_brightness_set
function, setting the LED will result in the following error message:
leds mdio-bus:*:green:lan: Setting an LED's brightness failed (-524)
Backport a patch to silence this error message.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/18080
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
RTL8261N is used on some Airoha and Realtek devices. Move the driver
from Mediatek to generic so it can be used everywhere.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18163
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for Maginon MC-1200AC.
Hardware specifications:
SoC: MediaTek MT7621
Flash: 16 MB SPI Flash
RAM: 128 MB RAM
Ethernet:
2x 1G RJ45 ports
WLAN:
2.4GHz: MediaTek MT7603E
5GHz: MediaTek MT7613BE
LEDs: Red and blue status lights
Power: 12V DC
UART: 3.3V, 115200 baud, 8N1, like printed on silkscreen (GND,TX,RX,3.3V)
MAC addresses
-------------
+---------+-------------------+
| | MAC example |
+---------+-------------------+
| LAN | 80:3F:5D:xx:xx:72 |
| WAN | 80:3F:5D:xx:xx:73 |
| WLAN 2g | 80:3F:5D:xx:xx:74 |
| WLAN 5g | 80:3F:5D:xx:xx:75 |
+---------+-------------------+
Installation:
The firmware can be flashed via the U-Boot recovery web interface.
To access it, hold the reset button while powering on the device.
U-Boot recovery web interface is then avaiable at 192.168.10.1.
Alternatively, the image can be loaded using the U-Boot serial interface and TFTP.
Signed-off-by: Simon Etzlstorfer <simon@etzi.at>
Link: https://github.com/openwrt/openwrt/pull/17671
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Adds latest 6.6 patches from the Raspberry Pi repository.
These patches were generated from:
https://github.com/raspberrypi/linux/commits/rpi-6.6.y/
With the following command:
git format-patch -N v6.6.83..HEAD
(HEAD -> 08d4e8f52256bd422d8a1f876411603f627d0a82)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The CONFIG_NET_SWITCHDEV option is needed by CONFIG_DSA and some other
options. It is boolean, we have to compile it into the kernel it self.
Activate it for all targets in the generic configuration, it is already
activated for most of them. This allows to install DSA drivers as a
module.
On the ramips/mt7620 target the kernel would grown by 4.5kB.
For some small targets which do not support a DSA switch by default the
option is deactivated.
Link: https://github.com/openwrt/openwrt/pull/17668
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This has several advantages:
* reduction in the size of the kernel and the complete image. Individual
devices only need two of the four binaries. In combination with the second
commit it reduces kernel size by 64.2 kB and image size by 22.8 kB,
* the option to extend this package with firmware for future SoCs,
* combining the kernel and binary blobs with another licence may not be
fully compatible with the licence used by Linux. The current PHY firmware
is built into the kernel. This comit converts it to a package.
Tested on AVM 5490 and BT Home Hub 5A.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17669
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The next commit converts the firmware used by this driver
to a package. Due to the fact that the driver is shipped
as a package the firmware is already available.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17669
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
fixed wrong reg.
The original commit assumed the size part was the end of the reg.
Fixes: 7dbac3433f ("mediatek: add support for reyee AX3200-E5")
Signed-off-by: Boyang Sun <boyinthesun@163.com>
Link: https://github.com/openwrt/openwrt/pull/18074
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Zyxel LTE7490-M904 is an 802.3at PoE powered LTE outdoor (IP68) CPE
with integrated directional antennas.
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256 MB
- Flash: 128 MB MB NAND (MX30LF1G18AC)
- WiFi: MediaTek MT7603E 802.11b/g/n
- Switch: 1 LAN port (1 Gbps)
- LTE/3G/2G: Quectel EG18-EA LTE-A Cat. 18 connected by USB3 to SoC
- SIM: 1 micro-SIM slots under transparent cover
- Buttons: Reset, WLAN under same cover
- LEDs: Multicolour green/red/amber under same cover (visible)
- Power: 802.3at PoE via LAN port
The device is built as an outdoor ethernet to LTE bridge or router.
The wifi interface is intended for installation and/or temporary
management purposes only.
UART Serial:
57600N1, located on populated 5 pin header J5:
[o] GND
[ ] key - no pin
[o] RX
[o] TX
[o] 3.3V Vcc
Remove the SIM/button/LED cover and 12 screws holding the back plate
and antenna cover together. Be careful with the cables.
Installation from OEM web GUI:
- Log in as "admin" on OEM web GUI
- Upload OpenWrt initramfs-recovery.bin image on the
Maintenance -> Firmware page
- Wait for OpenWrt to boot and ssh to root@192.168.1.1
- Sysupgrade to the OpenWrt sysupgrade image and reboot
For more details about flashing see:
2449a63208 (ramips: mt7621: Add support for ZyXEL NR7101, 2021-04-19)
Main porting work done by Ernesto Castellotti <ernesto@castellotti.net>:
bf1c12f68b (ramips: add support for ZyXEL LTE7490-M904, 2023-12-20)
Signed-off-by: Eric Schäfer <eric@es86.de>
Link: https://github.com/openwrt/openwrt/pull/17485
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Forum discussion : https://forum.openwrt.org/t/aps-256va-help-for-identification/143653/52
Specification:
Power: 12-36V input via 5,5/2,1 DC barrel jack, or 5V Micro USB-B
CPU: Atheros AR9344 rev 2
RAM: 128MB
Flash: 16MB
WI-Fi: 2.4GHz
Fast Ethernet: 1 WAN and 2 LAN
USB: 2 x USB-A, 1 x micro-USB-B (for power input)
WWAN: 3G modem via extended mini-PCIE form factor (can be replaced with Wifi 5GHz card)
The device come with custom openwrt BB an CC.
Because of limited LAN port, I disable GMAC0, so the WAN port can be connected to GMAC1 and function as LAN port as well.
Enable ssh access and Backup:
1. open router admin page via LAN cable
2. browse 192.168.111.1:8000
3. login with password 123456
4. click wifi icon on top menu
5. change the path at the end of the url (after random hash) with /admin/system/flashops
it will looks like this:
http://192.168.111.1:8000/cgi-bin/luci/;stok=29698152cf64c980177a04f86c99ea0d/admin/system/flashops
(the hash after "stok=" will be different)
6. restore the config with this modified backup (can be created manually by changing dropbear config to allow ssh)
https://drive.google.com/file/d/1Vs-k7DHBSRZFfkxv1cMOmgAPZfB-RUen/view?usp=sharing
7. now you can login to ssh with root user and 123456 password, and backup all partition and upgrade firmware
!!! BACKUP EVERY PARTITION !!!
Flashing instructions:
- Flash directly from factory web interface accessed from "Enable ssh access" step 5
Signed-off-by: Roy H <roy@altbytes.com>
Link: https://github.com/openwrt/openwrt/pull/17939
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The M1200 v1 is similar to the TR1200 series from Cudy. Differences:
- Only 1 LAN port
- No USB
Specifications:
- MT7628
- MT7628AN (2.4G b/g/n) and MT7613BE (5G ac/n) wifi
- 128 MB RAM
- 16 MB flash
MAC Addresses:
- There is one on the label, e.g. xx:xx:xx:xx:xx:A4
- LAN (bottom connector) is the same as the label, e.g. xx:xx:xx:xx:xx:A4
- WAN (top connector) is label + 1, e.g. xx:xx:xx:xx:xx:A5
- WLAN (2.4G) is the same as the label, e.g. xx:xx:xx:xx:xx:A4
- WLAN (5G) is label + 2, e.g. xx:xx:xx:xx:xx:A6
UART:
- is available via the pin holes on the board
- The pinout is printed to the board: P: VCC, G: GND, R: RX, T:TX
- RX and TX require solder bridges to be installed
- Do NOT connect VCC
- Settings: 3.3V, 115200, 8N1
GPIO:
- There are two LEDs: Red (GPIO 4) and White (GPIO 0)
- There are two buttons: Reset (GPIO 11) and WPS (GPIO 5)
Migration to OpenWrt:
- Download the migration image from the Cudy website (it should be available as soon as OpenWrt officially supports the device)
- Connect computer to LAN (bottom connector) and flash the migration image via OEM web interface
- OpenWrt is now accessible via 192.168.1.1
Revert back to OEM firmware:
- Set up a TFTP server on IP 192.168.1.88 and connect to the WAN port (upper port)
- Provide the Cudy firmware as recovery.bin in the TFTP server
- Press the reset button while powering on the device
- Recovery process is started now
- When recovery process is done, OEM firmware is accessible via 192.168.10.1 again
General information:
- No possibility to load a initramfs image via U-Boot because there is no option to interrupt U-Boot
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18233
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The nanopi R6S, R6C and nanopc T6 platforms are based on rk3588(s) SoC,
which has fast and slow CPU cores. Set up network interrupt affinity to be
on the fast CPU cores by default. This is similar to the way this was
already configured on nanopi R4S.
Signed-off-by: Michel Lespinasse <michel@lespinasse.org>
Link: https://github.com/openwrt/openwrt/pull/17638
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set up openwrt to handle the reset button appropriately (so that it
can trigger the various recovery modes) on the nanopi R6S and R6C models.
Signed-off-by: Michel Lespinasse <michel@lespinasse.org>
Link: https://github.com/openwrt/openwrt/pull/17638
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set up openwrt to show boot progress on the nanopi R6S or R6C system LED.
The LED blinking states indicate the boot stage. The LED is defined as
a power LED, but can still be set to heartbeat in /etc/config/system
after the system is done booting.
Signed-off-by: Michel Lespinasse <michel@lespinasse.org>
Link: https://github.com/openwrt/openwrt/pull/17638
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The code can be made more efficient by not extracting the sysupgrade.tar but
rather just querying for the filesize within the archive. Resorting to
manual update of UBI volume is extra work too, setting CI_KERNPART=rootfs_0
is enough.
Suggested-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/17806
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The OpenWrt One is the only board listing kmod-nvme as part of it's
default package set.
Remove kmod-nvme from the default package set as the board is sold
without an NVMe SSD and the M.2 slot can also be used for other
purposes.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of hardcoded metadata, put some sensible data instead.
Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/17551
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for Genexis Pulse EX400 / Inteno Pulse EX400. A branded
variant for the Finnish ISP DNA has already been added in fea2264d9f
(ramips: mt7621: Add DNA Valokuitu Plus EX400, 2023-07-31). This commit
adds support for the generic variants with Inteno and Genexis branding.
Inteno changed its name to Genexis and both brandings exist.
In terms of electronics, there is no difference between the DNA-branded
version and other brandings. LED markings on the case are different,
though. While the DNA-version has a "software-update" LED, the other
versions have a WPS LED. To reduce user confusion, create a separate
image.
Add the different device-tree with the different LED and rename things
to work the same way for both variants.
Specifications:
- Device: Genexis Pulse EX400 / Inteno Pulse EX400
- SoC: MT7621A
- Flash: 256 MB NAND
- RAM: 256 MB
- Ethernet: Built-in, 2 x 1 GbE
- Wifi: MT7603 2.4 GHz 2x2 MIMO, MT7615 5 GHz 4x4 MU-MIMO
- USB: 1x 2.0
- LEDs (GPIO): green/red status, green WPS
- LEDs (SX9512, unsupported): Broadband, Wi-Fi 2.4G, Wi-Fi 5G
- Buttons (GPIO): Reset
- Buttons (SX9512, unsupported): Wi-Fi 2.4G, Wi-Fi 5G, WPS
MAC addresses:
- LAN: U-Boot 'ethaddr' (label)
- WAN: label + 1
- 2.4 GHz: label + 6
- 5 GHz: label + 7
Serial:
There is a black block connector next to the red ethernet connector. It
is accessible also through holes in the casing.
Pinout (TTL 3.3V)
+---+---+
|Tx |Rx |
+---+---+
|Vcc|Gnd|
+---+---+
Firmware:
The vendor firmware is a fork of OpenWrt (Reboot) with a kernel version
4.4.93. The flash is arranged as below and there is a dual boot
mechanism alternating between rootfs_0 and rootfs_1.
+-------+------+------+-----------+-----------+
| | env1 | env2 | rootfs_0 | rootfs_1 |
| +------+------+-----------+-----------+
| | UBI volumes |
+-------+-------------------------------------+
|U-Boot | UBI |
+-------+-------------------------------------+
|mtd0 | mtd1 |
+-------+-------------------------------------+
| NAND |
+---------------------------------------------+
In OpenWrt rootfs_0 will be used as a boot partition that will contain the
kernel and the dtb. The squashfs rootfs and overlay are standard OpenWrt
behaviour.
+-------+------+------+-----------+--------+------------+
| | env1 | env2 | rootfs_0 | rootfs | rootfs_data|
| +------+------+-----------+--------+------------+
| | UBI volumes |
+-------+-----------------------------------------------+
|U-Boot | UBI |
+-------+-----------------------------------------------+
|mtd0 | mtd1 |
+-------+-----------------------------------------------+
| NAND |
+-------------------------------------------------------+
U-boot:
With proper serial access, booting can be halted to U-boot by pressing
any key. TFTP and flash writes are available, but only the first one has
been tested.
NOTE: Recovery mode can be accessed by holding down the reset button while
powering on the device. The led 'Update' will show a solid green light
once ready. A web server will be running at 192.168.1.1:80 and it will
allow flashing a firmware package. You can cycle between rootfs_0 and
rootfs_1 by pressing the reset button once.
Root password:
With the vendor web UI create a backup of your settings and download the
archive to your computer. Within the archive in the file
/etc/shadow replace the password hash for root with that of a password you
know. Restore the configuration with the vendor web UI and you will have
changed the root password.
SSH access:
You might need to enable the SSH service for LAN interface as by default
it's enabled for WAN only.
Installing OpenWrt:
With the vendor web UI, or from the U-Boot recovery UI, install the
OpenWrt factory image. Alternatively, ssh to the device and use
sysupgrade -n from cli.
Finalize by installing the OpenWrt sysupgrade image to get a fully
functioning system.
Reverting to the vendor firmware:
Boot with OpenWrt initramfs image
- Remove volumes rootfs_0, rootfs and rootfs_data and create vendor
volumes.
ubirmvol /dev/ubi0 -n 2
ubirmvol /dev/ubi0 -n 3
ubirmvol /dev/ubi0 -n 4
ubimkvol /dev/ubi0 -N rootfs_0 -S 990
ubimkvol /dev/ubi0 -N rootfs_1 -S 990
Power off and enter to the U-boot recovery to install the vendor
firmware.
Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/17551
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move common definitions for DNA Valokuitu Plus EX400 to a dtsi include.
This is in preparation of adding the non-branded variant of the device
produced by Genexis / Inteno in the next commit. The device with DNA
branding differs in the LED labling on the device.
Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/17551
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The build failed because the CONFIG_FSL_DPAA2_ETH_DCB option was not
set. Activate this option to build the driver with DCB support when it
is available.
Fixes: 40f1db9cb1 ("kernel: Add KERNEL_DCB (Data Center Bridging)")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This makes it possible to initialize the eMMC from scratch like it is
done for the BPI-R3 mini (without an SD card).
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This fixes the handling of some FS copper SFP modules using the RollBall
protocol and needing some extra treatment.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
This is only relevant for devices with USB support, and in itself changes
nothing in the kernel build. However, it is useful to further simplify the
dependencies of some USB network devices.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
The DWC2 driver used here supports a vbus-supply property to control
the GPIO. Use it instead of the local gpio,exports solution.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17357
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an industrial 4G router equipped with OpenWrt 14.07 OEM
customized version
WARNING: The original firmware device tree is common to multiple
boards, and the device tree name is H9350. This submitted device
tree is a modified version, which deletes the non-this-device parts
and adds GPIO watchdog.
Specification:
- SoC: MediaTek MT7620A
- Flash: 16 MB
- RAM: 128 MB
- Power: DC 5V-36V 1.5A
- Ethernet: 1x WAN, 4x LAN (10/100 Mbps)
- Wireless radio: 802.11n 2.4g-only
- LED:
System/Power (RUN): GPIO/26 active-low
Ethernet: 1x WAN, 4x LAN
Modem 1: GPIO/66 active-low
RF 1 (Modem 1 Signal): GPIO/67 active-low
Modem 2: GPIO 71 active-low
RF 2 (Modem 2 Signal): GPIO/24 active-low
WLAN: GPIO/72 active-low
WPS: GPIO/12 active-low
- Button:
WPS / RESET: GPIO/34 active-low
- UART: 1x UART on PCB - 115200 8N1
- GPIO Watchdog: GPIO/62 mode=toggle timeout=1s
- PCIe: 2x miniPCIe for modem
- SIM Slots: 2x SIM Slots
Issue:
- No factory partition, eeprom is located
at /lib/firmware/mt7620a.eeprom
Flash instruction:
Using UART:
1. Configure PC with a static IP address and setup an TFTP server.
2. Put rootfs into the tftp directory.
3. Connect the UART line as described on the PCB.
4. Power up the device and press Ctrl+C to break auto boot.
5. Use `system 6` command and follow the instruction to set device
and tftp server IP address and input the rootfs file name.
U-boot will then load the rootfs and write it into
the flash.
6. Use `system 1` command and follow the instruction to set device
and tftp server IP address and input the firmware file name.
U-boot will then load the firmware once.
7. Login to LuCI and use LuCI upgrade firmware.
Original Firmware Dump / More details:
https://blog.gov.cooking/archives/research-hongdian-h8922-and-flash.html
Signed-off-by: Coia Prant <coiaprant@gmail.com>
Tested-by: Coia Prant <coiaprant@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17472
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
FCC ID: TVE-121402
Fortinet FAP-221-C is an indoor access point with 1gb ethernet port,
dual-band wireless, internal antenna plates, and 802.3at PoE+.
Hardware and board design are from Senao. The device appears very
similar to the EnGenius EAP1200H, albeit with double the flash and RAM.
**Specifications:**
- QCA9557 SOC
- QCA9882 WLAN PCI card, 5 GHz, 2x2, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 32 MB FLASH FL256SAIFR0
- 2x 128 MB RAM NT5TU64M16HG
- UART populated
- 4 internal antenna plates
- 5 LEDs, 1 button (power, 'warning', eth0, wifi1, wifi2) (reset)
Amber LAN LED appears hardwired to ethernet port. Power LED is green
only. Other LEDs are amber/green.
**MAC addresses:**
1 MAC Address in flash at end of uboot
ASCII encoded, no delimiters
Labeled as "MAC Address" on case
**Serial Access:**
Pinout: (arrow) VCC GND RX TX
Pins are populated with a header and traces not blocked.
Bootloader is set to 9600 baud, 8 data, 1 stop.
**Console Access:**
Bootloader:
Interrupt boot with Ctrl+C
Press "k" and enter password "1"
OR
Hold reset button for 5 sec during power on
Interrupt the TFTP transfer with Ctrl+C
to print commands available, enter "help"
OEM:
default username is "admin", password blank
telnet is available at default address 192.168.1.2
serial is available with baud 9600
to print commands available, enter "help"
or tab-tab (busybox list of commands)
**Installation:**
Use factory.bin with OEM upgrade procedures
OR
Use initramfs.bin with uboot TFTP commands.
Then perform a sysupgrade with sysupgrade.bin
**TFTP Recovery:**
Using serial console, load initramfs.bin using TFTP
to boot openwrt without touching the flash.
**Return to OEM:**
The best way to return to OEM firmware
is to have a copy of the MTD partitions
before flashing Openwrt.
Backup copies should be made of partitions
"fwconcat0", "loader", and "fwconcat1"
which together is the same flash range
as OEM's "rootfs" and "uimage"
by loading an initramfs.bin
and using LuCI to download the mtdblocks.
It is also possible to extract from the
OEM firmware upgrade image by splitting it up
in parts of lengths that correspond
to the partitions in openwrt
and write them to flash,
after gzip decompression.
After writing to the firmware partitions,
erase the "reserved" partition and reboot.
Signed-off-by: Bernardus Jansen <bernardus@bajansen.nl>
Link: https://github.com/openwrt/openwrt/pull/18109
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The kmod-mlxsw-spectrum driver activated CONFIG_DCB indirectly already
on all targets which are building this driver. All other DCB capable
driver did not activate their DCB support.
CONFIG_DCB increases the uncompressed kernel size by about 7.8KB.
CONFIG_DCB is only needed some data center Ethernet cards and not used
on normal routers. Activate it only on the x86_64 and the armsr_arm64
target which are used on normal servers or in VMs.
Link: https://github.com/openwrt/openwrt/pull/17672
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The M1300 v2 is similar to the WR1300 series from Cudy. Differences:
- Only 1 LAN port
- No USB
Specifications:
- MT7621
- MT7603E (2.4G b/g/n) and MT7613BE (5G ac/n) wifi
- 128 MB RAM
- 16 MB flash
MAC Addresses:
- There is one on the label, e.g. xx:xx:xx:xx:xx:1C
- LAN (bottom connector) is the same as the label, e.g. xx:xx:xx:xx:xx:1C
- WAN (top connector) is label +2, e.g. xx:xx:xx:xx:xx:1E
- WLAN (2.4G) is the same as the label, e.g. xx:xx:xx:xx:xx:1C
- WLAN (5G) is the same as WAN, e.g. xx:xx:xx:xx:xx:1E
UART:
- is available via the pin holes on the board
- From inner to outer pin: TX, RX, GND, VCC
- Do NOT connect VCC
- Settings: 3.3V, 115200, 8N1
GPIO:
- There are two LEDs: Red (GPIO 3) and White (GPIO 4)
- There are two buttons: Reset (GPIO 8) and WPS (GPIO 10)
Migration to OpenWrt:
- Download the migration image from the Cudy website (it should be available as soon as OpenWrt officially supports the device)
- The migration image is also available here until a image is provided by Cudy: https://github.com/RolandoMagico/openwrt-build/releases/tag/M1300_Build_20240222
- File: openwrt-ramips-mt7621-cudy_m1300-v2-squashfs-flash-signed.bin
- Connect computer to LAN (bottom connector) and flash the migration image via OEM web interface
- In the migration image, LAN and WAN are swapped. Computer must be connected to the other port after flashing
- OpenWrt is now accessible via 192.168.1.1
- After flashing an up to date OpenWrt image, LAN and WAN settings are again the same as in the OEM firmware
- So use the other connector again
Revert back to OEM firmware:
- Set up a TFTP server on IP 192.168.1.88 and connect to the LAN port (lower port)
- Provide the Cudy firmware as recovery.bin in the TFTP server
- Press the reset button while powering on the device
- Recovery process is started now
- When recovery process is done, OEM firmware is accessible via 192.168.10.1 again
General information:
- No possibility to load a initramfs image via U-Boot because there is no option to interrupt U-Boot
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18139
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit switches the control of the leds connected to the Lantiq PEF7071V
PHY to an upstream solution. There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/18153
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The spaces in variables have been stripped since commit 551e04f3c9
("base-files: strip space and tab characters from ASCII mac address"),
resulting "Vfac_mac " matches nothing. Fix the issue by removing the
space at end.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/18150
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This board is also as known as SuperElectron ZN-M5 and ZN-M8. However,
for ZN-M5 and ZN-M8, there's another version uses ZX279128 as CPU
chip, which is unsupported.
You can check it in "高级设置" > "系统日志" > "内核日志" page from webUI.
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, WPS
Power: DC 12V 1A
Stock layout flash instructions:
Login into webUI and upload sysupgrade firmware in "系统管理" > "升级固件" page.
Remember to unselect "保留配置" ("Keep configurations") first before doing that.
OpenWrt U-Boot layout flash instructions:
1. Flash stock layout firmware first.
2. Connect to the device via SSH, and backup everything,
especially 'Factory' partition.
3. Unlock MTD partitions:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
4. Write new BL2 and FIP:
mtd write openwrt-mediatek-filogic-cmcc_a10-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cmcc_a10-ubootmod-bl31-uboot.fip FIP
5. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/18121
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Quoting the kconfig description for CONFIG_PCPU_DEV_REFCNT:
network device refcount are using per cpu variables if this option is
set. This can be forced to N to detect underflows (with a performance
drop).
This was introduced from kernel 5.13 and was wrongly set as disabled.
Some target actually enables it but this should be always enabled unless
refcount needs to be debugged (unlikely for production images)
Enable in generic and drop the entry in every other target.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18174
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds the missing properties to address the following warnings:
Warning (reg_format): /soc@0/spi@78b5000/flash@0/partitions/partition@x:reg: property has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1)"
Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: #18180
Signed-off-by: Robert Marko <robimarko@gmail.com>
all espressobins have topaz switch as same soc, so it is safe to add
kmod-dsa-mv88e6xxx to all
Signed-off-by: Jiri Kastner <cz172638@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18161
Signed-off-by: Robert Marko <robimarko@gmail.com>
Due to API changes during the backport, the default value of Tx LPI
timer is accidentally left unset, breaking the network if EEE is on.
Set the default timer to 1ms on init, and fix an incorrect condition.
Fixes: d8315d5358 ("kernel: backport Mediatek SoC EEE support")
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
I selected one subtarget after the other and refreshed their
configuration using this command:
make kernel_oldconfig CONFIG_TARGET=subtarget
For MT7629 I had to re-add CONFIG_LEDS_SMARTRG_LED manually.
Otherwise, building MT7629 with ALL_KMODS we get prompted for
LEDS_SMARTRG_LED and this will break CI and in future buildbot
compilation. See commit 6bdea8c7bd ("mediatek: mt7629: 6.6: disable
LEDS_SMARTRG_LED by default") for more details.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Prior to commit 8a7d12d674,
cdc-ethernet USB LTE modems (e.g. Quectel EC200A) were consistently named
usb0. After 8a7d12d67, devices began renaming to eth1 due to an assumption
that local MAC addresses originate exclusively from the kernel. Some
devices provide driver-assigned local MACs, causing point-to-point
interfaces with driver-set MACs to adopt eth%d names instead of usb%d.
Restore the naming exception for point-to-point devices: interfaces
without driver MACs or with driver-provided local MACs will retain the
usb%d convention. This addresses issues reported in [1] and fixed in [2].
[1] https://lore.kernel.org/all/Z00udyMgW6XnAw6h@atmark-techno.com/
[2] https://lore.kernel.org/all/20241203130457.904325-1-asmadeus@codewreck.org/
Tested-by: Ahmed Naseef <naseefkm@gmail.com>
Signed-off-by: Ahmed Naseef <naseefkm@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17757
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport Mediatek SoC EEE support from net-next upstream.
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[refreshed patches]
Drop Airoha MTD parser patch as a better solution was agreed with a
fixed partition table.
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> # tested on Quantum W1700k
Link: https://github.com/openwrt/openwrt/pull/18112
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Cleanup kernel config and drop all unrelated configs. This have the side
effect of fixing the port not going up automatically due to Bridge VLAN
Filtering disabled.
Link: https://github.com/openwrt/openwrt/pull/18112
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add support for Linksys MR5500 (Hydra 6 Pro).
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Kingston D2516ECMDXGJD (512 MiB)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
QCN9024 (4x4:4 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (4 Ports 10/100/1000 GBASE-T)
* Flash: Gigadevice GD5F2GQ5REYIH (256 MiB)
* LEDs: 1x multi-color PWM LED
1x blue led for USB (GPIO 19 Active High)
* Buttons: 1x WPS (GPIO 27 Active Low)
1x Reset (GPIO 28 Acive Low)
5x ethernet port LEDs (amber for activity & green for link up)
* Peripherals: 1x USB2 (powered by GPIO 17 Active Low)
support for USB3 will be added in a separate PR
* FCC ID: 2AYRA-03734
Flash instructions:
1. On OEM firmware, login to the device (typically at http://192.168.1.1) and click 'CA'
in the bottom right corner -> Connectivity -> Manual Upgrade. Alternatively, browse to
http://<router IP>/fwupdate.html.
Upgrade firmware using openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin image.
Optionally install on second partition, after first boot check actual partition:
fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin kernel
and in case of 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
fw_printenv -n boot_part
In case of 2:
flash_erase /dev/mtd12 0 0
nandwrite -p /dev/mtd12 openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin
or in case of 1:
flash_erase /dev/mtd14 0 0
nandwrite -p /dev/mtd14 openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin
After first boot install firmware on second partition:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin kernel
or:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware.
Download firmware from OEM website:
MR5500: https://support.linksys.com/kb/article/207-en/
From serial or SSH:
fw_printenv boot_part
in case of 1:
mtd -r -e alt_kernel -n write FW_MR5500_1.1.2.209598_prod.img alt_kernel
else in case of 2:
mtd -r -e kernel -n write FW_MR5500_1.1.2.209598_prod.img kernel
4. Boot from USB
This allows you loading an OpenWrt image into RAM and is meant for recovery scenarios only.
Enable loading image from USB in u-boot. From serial or SSH:
fw_setenv bootusb 'usb start && usbboot &loadaddr && bootm $loadaddr'
fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
Copy OpenWrt initramfs image to USB:
dd bs=1M if=openwrt-qualcommax-ipq50xx-linksys_mr5500-initramfs-uImage.itb of=/dev/sda
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17958
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. There should be no functional changes.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Some devices have both the color/function and label property defined.
The label can be constructed from the former properties, making it
redundant.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
btmtk.ko is used by btusb.ko and btmtkuart.ko, add it into an own
package and make both packages depend on it.
Fixes: 1c42a0be36 ("kernel: modules: bluetooth: separating UART and USB drivers")
Link: https://github.com/openwrt/openwrt/pull/18110
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This makes sgmii work for 1000Base-T SFPs by stupidly adding the sgmii mode
wherever 1000base-x is accepted. No intelligence has been used in the
process. But it "works for me".
There is an obvious need for refactoring this code to make it more obvious
how and why we configure the mac/phy link like we do for different modes.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://github.com/openwrt/openwrt/pull/17950
Signed-off-by: Sander Vanheule <sander@svanheule.net>
These features have been added to the mdio-i2c driver and are now used by
the sfp driver. The support is required for some newer SFPs.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://github.com/openwrt/openwrt/pull/17950
Signed-off-by: Sander Vanheule <sander@svanheule.net>
This driver use "phy-handle" as a placeholder for mac configuration
data. Such handles are therefore required for all ports - even those
connected directly to SFP slots and having a managed property set to
"in-band-status".
The DSA core will register these nodes as if they are real phys. This
prevents later attachment of pluggable phys with errors like
sfp sfp-p8: sfp_add_phy failed: -EBUSY
Replace the virtual SFP slot handles with "pseudo-phy-handle" to keep
the driver logic as-is but hide the node from the DSA core.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://github.com/openwrt/openwrt/pull/17950
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The SMBus patch broke the logic and caused the driver to always
register an mdio bus, regardless of the sfp. Restore original
logic.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://github.com/openwrt/openwrt/pull/17950
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Re-probing on interface up will register a new duplicate hwmon device. Skip
the hwmon probe if we already have a sensor device.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://github.com/openwrt/openwrt/pull/17950
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Fix a typo which resulted in wrong .read hooks and unset .write
hooks. This made I2C_SMBUS_BLOCK_DATA transfers dereference the
NULL .write hook and Oops.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://github.com/openwrt/openwrt/pull/17950
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The log noise emmitted by this driver is overwhelming, even for developers
looking at specific issues. Demoting to debug allows individual messages
to be dynamically enabled instead.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://github.com/openwrt/openwrt/pull/17950
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Adding a static IPv4 route made the driver repeatedly print
rtl83xx_l3_nexthop_update: Setting up fwding: ip 192.168.1.42, GW mac 0000001b21a7xxxx
Route with id 3 to 192.168.99.0 / 24
rtl83xx_l3_nexthop_update: total packets: 0
Warning: TEMPLATE_FIELD_RANGE_CHK: not configured
These messages are only useful to developers while debugging offloading.
Demote to debug level, which in general is more useful for developers
by allowing precise dynamic control.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://github.com/openwrt/openwrt/pull/17950
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Function remove_oem_ubi_volume was called before CI_UBIPART variable was defined.
Fixes: df1f6e1e18 (qualcommax: ipq807x: Remove OEM UBI volume before upgrade for Linksys MX devices)
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18090
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use Bluetooth UART and USB packages separetly.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15118
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Both hardware and firmware of these devices appears identical except for the
manufacturers logo and device name. The documented XikeStor SKS8300-8X
installation method is verified to work on the ONTi ONT-S508CL-8S using
Openwrt images made for the XikeStor SKS8300-8X. This includes the OEM boot
loader magic password phrases.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Link: https://github.com/openwrt/openwrt/pull/18071
Signed-off-by: Sander Vanheule <sander@svanheule.net>
By switching to the new RTL8231 driver in commit b7af54d5c1 ("realtek:
Simple conversions to RTL8231 MFD driver"), the bootloader state of the
RTL8231's pins is now maintained. As the bootloader de-asserts the PoE
enable signal, this means PoE output is no longer available.
Add a gpio-hog with high output, restoring the line value from when the
pin was configured (by default) as an input with a pull-up resistor.
This will hard-enable the PoE output, but the individual ports can still
be administratively disabled by realtek-poe or a similar tool.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Convert the router to DSA.
Co-Developed-by: Matt Beaumont <github@beaum.xyz>
Tested-by: Matt Beaumont <github@beaum.xyz>
Link: https://github.com/openwrt/openwrt/pull/12478
Signed-off-by: Nick Hainke <vincent@systemli.org>
On the ipq50xx platform, the internal GE PHY at phy address 7 on mdio0
must be enabled as it's used to detect the virtual switch in qca-ssdk.
This is a platform wide condition and is therefore part of the dtsi.
However, by enabling the mdio0 bus in board-specific dts files, the ge_phy
is implicitly enabled. So, let's remove the superfluous status property
in the dts files for Linksys MX2000 and MX5500.
While at it, remove the redundant phy-mode property as it's set to sgmii
by default in the ipq5018-ess.dtsi file and fix indentation in the
firmware property of the q5v6_wcss node.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18029
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ascii-env driver enables reading name pair values from nand in ascii layout.
So, let's pick up and set the mac address accordingly.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18029
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add validation and support for parsing of name/value pairs with CRLF line
endings.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17935
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Specifications:
- SoC: Allwinner A31 @ 1GHz
- DRAM: 1/2Gb DDR3
- SD-card slot
- NAND: 8/16Gb MLC
- Ethernet: 1x 10/100/1000Mbps (RTL8211E)
- Wireless: Ampak AP6210 (BCM43362)
- 2x USB2.0
- 1x mPCIe slot for 4G cards
- 1x SIM slot
- HDMI/VGA via simplefb
- RTC with battery
- Power via DC12V / 3A
Installation:
Use the standard sunxi installation to an SD-card. NAND is
not supported.
This is to re-add proper support for an older device.
Link: https://openwrt.org/toh/merrii/hummingbird
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Add missing patch description, so all generic patches can be applied
to a kernel tree using 'git am'.
Fixes: d23e0a0086 ("kernel: backport MHI patch required by an upcoming mac80211 update")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The UBI volume name in OEM firmware for Linksys MX2000, MX5500, and
SPNMX56 is 'squashfs' instead of 'rootfs'. So let's update the volume
accordingly.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17968
Signed-off-by: Robert Marko <robimarko@gmail.com>
The SPNMX56 is an ISP-branded and distributed device similar to the MX5500
with the same Wifi chips (IPQ5018 for 2.4G and QCN9074 for 5G) but has an
additional QCA8081 PHY providing a 2.5gbps ethernet WAN port.
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Winbond W634GU6NB-11 (512 MiB DDR3-933)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
QCN9024 (4x4:4 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (3 Ports 10/100/1000 GBASE-T) and a
QCA8081 phy (up to 2.5 Gbps)
* Flash: Gigadevice GD5F2GM7RExxG (256 MiB)
* LEDs: 1x multi-color PWM LED
* Buttons: 1x WPS (GPIO 27 Active Low)
1x Reset (GPIO 28 Acive Low)
Flash instructions:
1. On OEM firmware, login to the device (typically at http://192.168.1.1)
and click 'CA' in the bottom right corner -> Connectivity ->
Manual Upgrade. Alternatively, browse to http://<router IP>/fwupdate.html
Upload openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin
Optionally flash 2nd partition, after first boot check actual partition:
fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin kernel
and in case of 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware
hit Enter once booted and enter credentials (login: root, password: admin)
fw_printenv -n boot_part
In case of 2:
flash_erase /dev/mtd12 0 0
nandwrite -p /dev/mtd12 openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin
or in case of 1:
flash_erase /dev/mtd14 0 0
nandwrite -p /dev/mtd14 openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin
After first boot install firmware on second partition:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin kernel
or:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware.
Download firmware from OEM website:
Firmware for this device cannot be searched for on the Linksys website.
Instead, we'd have to use serial to intercept the URL of the firmware
while it's trying to update. Firmware is ISP specific:
Toob (UK): http://download.linksys.com/updates/20241125t080737/FW_MX56TB_1.0.1.216218_prod.img
The intention is to collect URLs for different ISPs on a wiki page.
From serial or SSH:
fw_printenv boot_part
in case of 1:
mtd -r -e alt_kernel -n write FW_MX56TB_1.0.1.216218_prod.img alt_kernel
else in case of 2:
mtd -r -e kernel -n write FW_MX56TB_1.0.1.216218_prod.img kernel
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17968
Signed-off-by: Robert Marko <robimarko@gmail.com>
Import patch from MediaTek's SDK to hack-6.6 which dumps all relevant
registers of the Ethernet controller in case of a forced reset.
This can help to debug and find the cause for sporadic resets seen on
Filogic SoCs when used with OpenWrt's Linux 6.6.
Link: 73d44392b8
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Both share the same OEM firmware but differ in product_name for safeloader
product_name:MR1800X,product_ver:1.0.0,special_id:45550000
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
Link: https://github.com/openwrt/openwrt/pull/17965
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The proposed detection method was based on reading the LAUNCH_FREADY core flag.
However, this method only works before the cores are launched.
For this reason, the core number detection method has been changed to a simpler one.
For mt6721s the 17th revision bit is zero, hence we know that it is this chip,
so the number of cores is 1.
Fixes: https://github.com/openwrt/openwrt/issues/17764
Tested-by: Enrico Mioso <mrkiko.rs@gmail.com>
Tested-by: Simon Etzlstorfer <simon@etzi.at>
Tested-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Co-authored-by: Shiji Yang <yangshiji66@qq.com>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/17834
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Aliyun AP8220 is an AP manufactured by Edgecore.
(Very similar to Edgecore EAP102)
Hardware specifications:
SoC: Qualcomm IPQ8071A
RAM: 1GB of DDR4 600MHz
Flash1: MX25U3235F 4MB
Flash2: MX30UF1G18AC 128MB
Ethernet: 2x 2.5G RJ45 port
USB: 2x USB-A 2.0 port
WiFi1: QCN5024 2.4GHz
WiFi2: QCN5054 5GHz
Power: DC 12V / PoE
Flash instructions:
1. Connect the router via serial port
2. Keep pressing @ until uboot is interrupted
3. Download the initramfs image, rename it to
initramfs.bin, host it with tftp server
4. Run these commands:
tftpboot initramfs.bin
bootm
5. After openwrt boots up, use scp or luci
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17970
Signed-off-by: Robert Marko <robimarko@gmail.com>
Cleanup 02_network script indentation.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17970
Signed-off-by: Robert Marko <robimarko@gmail.com>
fix undesired red warning when upgrading in place ex5601-t0-stock model.
Signed-off-by: Pietro Ameruoso <p.ameruoso@live.it>
Link: https://github.com/openwrt/openwrt/pull/17973
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fixed the 5G mac address on KN-1910, rolled back the image size to stock
(there are no errors with loading large images in version 24.10.0),
minor spelling errors.
Signed-off-by: Anton Yu. Ivanusev <ivanusevanton@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/17946
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a MT7621-based device with 128MB NAND flash, 256MB RAM, and a USB port.
It is identical hardware to the already supported TP-Link ER605 v2 right
down to the PCB ID. The only differences are the color of the case and
the factory firmware features.
Signed-off-by: Raylynn Knight <rayknight@me.com>
Link: https://github.com/openwrt/openwrt/pull/17728
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set the SUPPORTED_DEVICES Device var so that sysupgrade images
are supported without a force.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/17964
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The upstream device-tree files are now using 'gateworks' instead of 'gw'
for compatible. Add this pattern so that the newer boards support
sysupgrade.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/17964
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit switches the control of the leds connected to the Maxlinear
GPY211C PHY to an upstream solution. The behaviour of LED1 is the same
as before. The behaviour of 2.5G-WAN LED has been changed. It is only
active when a 2.5G link is detected, which matches the stock software.
Additionally, the name of the WAN led has been changed to INTERNET.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17952
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently the erlite install shows Model as EBNT_E100, uses eth0 as lan,
eth1 as wan, and doesn't use eth2.
- define dts for this device, such that we get a cleaner naming here
- fix handing of this device to inlude eth2
- change eth0 to wan, like er-4/usg/etc as it once was intended
Fixes: https://github.com/openwrt/openwrt/issues/14946
Signed-off-by: Fabian Groffen <grobian@gentoo.org>
Link: https://github.com/openwrt/openwrt/pull/17758
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Apply "u-boot-dont-touch-spi-nand" to ASUS RT-AX59U, ASUS TUF-AX4200 as
well as ASUS TUF-AX6000 routers to prevent U-Boot from wiping MTD
child nodes from DT.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ASUS makes use of U-Boot's fdt_fixup_mtdparts() function which applies
the partitions defined in U-Boot's mtdparts and mtdids environment
variables to the devicetree passed over to Linux.
The undesired side-effect is that in this way also all additional
properties and child nodes get wiped, preventing NVMEM cells to be
defined for MTD partitions or UBI volumes.
To work-around this issue, add an additional compatible string
'u-boot-dont-touch-spi-nand' which can be used instead of 'spi-nand' in
case the replacement of the MTD partitions by U-Boot should be skipped
alltogether.
In practise this is mostly relevant for SPI-NAND which anyway comes only
with two partitions nowadays: 'Bootloader' and 'UBI_DEV'. Hence this
work-around is applicable for SPI-NAND only. Similar work-arounds for
other MTD devices can be created as well should they actually be needed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This reverts commit f628467dfd.
The initial fix was correct. However, a recently introduced bug in
base-files can cause some unexpected byte overwriting in eeprom.
Since it has been fixed, let's accept this patch again.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17892
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When support for Routerboard 911G was introduced, Routerboad 912UAG
device tree was used as a base, and the common part. This led to use of
40MHz as the reference clock frequency for both [1], while RB911G uses 25MHz
crystal on the board, causing heavy system clock drift.
Split the definition, and set the reference clock frequency for RB911G
back to 25MHz.
[1] a716ac5564 ("ath79: fix reference clock for RouterBoard 912UAG")
Fixes: bcc44b1212 ("ath79: support for MikroTik RouterBOARD 911G-(2,5)HPnD")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17944
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Refreshed patches for qualcommb/ipq95xx by running
make target/linux/refresh after creating a .config containing:
CONFIG_TARGET_qualcommbe=y
CONFIG_TARGET_qualcommbe_ipq95xx=y
CONFIG_TARGET_qualcommbe_ipq95xx_DEVICE_qcom_rdp433=y
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17822
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add missing select NEED_BPF_TOOLCHAIN in order to ensure that the toolchain
actually gets built.
Fixes: https://github.com/openwrt/openwrt/issues/17926
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The JG928A has an RTL8231 on the aux mdio bus. Add it to dts to expose
the GPIO pins used to control and monitor the fan speed. To enable speed
control, add the appropriate kernel driver module to DEVICE_PACKAGES.
Of note, this does not control all fans for the unit. The power supply
fans are not controlled.
Signed-off-by: Evan Jobling <evan@jobling.au>
Link: https://github.com/openwrt/openwrt/pull/17699
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Devices that rely on faking the NAND controler compatible for U-Boot
to patch the nodes should add it in their DTS directly, this does not
belong in the SoC DTSI.
Link: https://github.com/openwrt/openwrt/pull/17908
Signed-off-by: Robert Marko <robimarko@gmail.com>
Replace the existing SPI NAND controller patches with the latest v14 set
that is pending upstream, and include Ansuels patch that fixes it.
Bindings patch is removed as there is no point carrying it in OpenWrt.
Link: https://github.com/openwrt/openwrt/pull/17908
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add patch to fix Qcom SNAND driver and move the SNAND patches to
backports directory as they are shared between qualcommax and qualcommbe
target.
Fixes: #17897
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17900
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh the ipq50xx kernel config as it looks like it was created by hand
instead of kernel_menuconfig so we have stuff like DWC3 which is packaged
as a kmod in a generic way, QMI helpers are part of backports etc.
Link: https://github.com/openwrt/openwrt/pull/17890
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit fixes nmbm configuration mismatch error on Xiaomi AX3000t
with Winbond W25N01KVZEIR spi-nand:
'''
[ 0.786783] NMBM configuration mismatch
'''
Root cause:
1. U-Boot W25N01KV spi-nand driver ia compiled with 64B OOB size for the
chip and store this size in the nmbm signature;
2. Linux W25N01KV driver use 96B OOB.
The change doesn't affect AX3000t variants with other spi-nand chips
(ESMT, Foresee) because their Linux drivers use 64B OOB.
Fixes: openwrt#16972
Tested-by: Aleksandr Danilov <sc16me@gmail.com>
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17549
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds new "mediatek,bmt-mtd-overridden-oobsize" property. The
property helps avoid "NMBM configuration mismatch" error if mtd "OOB size"
is not equal to the "spare size" which is stored in the nmbm signature.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17549
Signed-off-by: Robert Marko <robimarko@gmail.com>
Newly introduced IPQ5018 specific symbols will stop compilation of
ipq807x and ipq60xx subtargets, so make sure to disable them in the
generic config.
Link: https://github.com/openwrt/openwrt/pull/17884
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for Linksys MX2000 (Atlas 6) and MX5500 (Atlas 6 Pro).
These devices are completely identical except for the secondary wifi
chip used for 5Ghz: QCN6102 is used on MX2000 while QCN9024 is used
on MX5500
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Winbond W634GU6NB-11 (512 MiB DDR3-933)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
* Wi-Fi: MX2000: QCN6102 (2x2:2 5 Ghz 802.11an/ac/ax)
MX5500: QCN9024 (4x4:4 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (4 Ports 10/100/1000 GBASE-T)
* Flash: Macronix MX35UF2GE4AD (256 MiB)
* LEDs: 1x multi-color PWM LED
* Buttons: 1x WPS (GPIO 27 Active Low)
1x Reset (GPIO 28 Acive Low)
Flash instructions (in case of MX2000, else replace with MX5500 images):
1. On OEM firmware, login to the device (typically at http://192.168.1.1) and click 'CA'
in the bottom right corner -> Connectivity -> Manual Upgrade. Alternatively, browse to
http://<router IP>/fwupdate.html.
Upgrade firmware using openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin image.
Optionally install on second partition, after first boot check actual partition:
fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin kernel
and in case of 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
fw_printenv -n boot_part
In case of 2:
flash_erase /dev/mtd12 0 0
nandwrite -p /dev/mtd12 openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin
or in case of 1:
flash_erase /dev/mtd14 0 0
nandwrite -p /dev/mtd14 openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin
After first boot install firmware on second partition:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin kernel
or:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware.
Download firmware from OEM website:
MX2000: https://support.linksys.com/kb/article/585-en/
MX5500: https://support.linksys.com/kb/article/587-en/
From serial or SSH:
fw_printenv boot_part
in case of 1:
mtd -r -e alt_kernel -n write FW_MX2000_1.1.7.210469_prod.img alt_kernel
else in case of 2:
mtd -r -e kernel -n write FW_MX2000_1.1.7.210469_prod.img kernel
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add QCN6122 platform support.
QCN6122 is a PCIe based solution that is attached to and enumerated
by the WPSS (Wireless Processor SubSystem) Q6 processor.
Though it is a PCIe device, since it is not attached to APSS processor
(Application Processor SubSystem), APSS will be unaware of such a decice
and hence it is registered to the APSS processor as a platform device(AHB).
Because of this hybrid nature, it is called as a hybrid bus device.
As such, QCN6122 is a hybrid bus type device and follows the same codepath
as for WCN6750.
This is a reversed engineered and heavily simplified version of below
downstream patch:
https://git.codelinaro.org/clo/qsdk/oss/system/feeds/wlan-open/-/ \
blob/NHSS.QSDK.12.4.5.r2/mac80211/patches/232-ath11k-qcn6122-support.patch
Co-developed-by: George Moussalem <george.moussalem@outlook.com>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Introduce support for the Qualcomm IPQ50xx SoC.
This series adds support for the following components:
- minimal boot support: GCC/pinctrl/watchdog/CPUFreq/SDI (upstreamed)
- USB2 (upstreamed)
- Thermal/Tsens
- PCIe gen2 1&2-lane PHY and controller
- PWM and PWM LED
- QPIC SPI NAND controller
- CMN PLL Block (provider of fixed rate clocks to GCC/ethernet/more.)
- Ethernet: IPQ5018 Internal GE PHY (1 gbps)
- Remoteproc MPD driver for IPQ5018 (2.4G) & QCN6122 (5/6G) Wifi
Co-developed-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Uses upstream DSA switch modules (rtl8365mb, rtl8366), similar to
RTL8367C and rtl8366rb swconfig drivers.
The package dependencies exclude targets built without kernel CONFIG_OF.
It also fixes the rtl8366rb LED support.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Replace outdated package names, order the remaining.
firewall4 is added again, since it is enabled by default.
The device is not a router by default, so this package
makes no sense in the default config. User can enable it
by theirself, or it will be automatically pulled via
dependency, e.g. luci-app-firewall.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Seems that the common style is to have whitespace around the operators
and the indent is single tab.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
The standard U-Boot boot scripts for Duckbills expect the
Linux kernel and device tree files installed below /boot
within the (ext4) root filesystem.
Also a raw zImage is expected instead of uImage.
Extend the SD card generation accordingly and while at,
install all possible Duckbill DT blobs there.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
The old RTL8231 driver integrated the MDIO bus access with the GPIO
control ops, making this driver not very portable to newer platforms.
It depended on the SoC ID instead of the compatible to determine the
MDIO access register, further complicating portability.
A new MFD driver is now available, which offers proper pin config as
well as optional LED support, which can work on any (bitbanged) MDIO
bus. Now that all devices have been migrated, we can drop the old code.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Fix broken NVMEM ASCII patch for x86 target as it does currently fail
compilation when OF is not compiled.
Also mute a warning for integer from pointer without a cast.
Fixes: 73a6cb983c ("generic: add pending support for NVMEM ASCII ENV layout driver")
Link: https://github.com/openwrt/openwrt/pull/17845
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
sf21 contains support for Bananapi BPI-RV2 which is a board available
to the general public. Limit the source-only flag to sf19a2890 instead.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Specification:
- Siflower SF21H8898
- 512MB DDR3, 128MB SPI-NAND and 16MB SPI-NOR
- 5x Gigabit ports (SF23P1240 QSGMII PHY and SF23P1211F RGMII PHY)
- 1x 2.5G port (Airoha EN8811H PHY)
- M.2 Key B slot with USB2.0, PCIEx1 and a NanoSIM card slot
- MiniPCIe slot with USB2.0 and PCIEx1
- 1x USB2.0 port through USB Hub
- PCF8563-compatible RTC
The SoC can only boot from SPI0. Two SPI flash chipselects are connected
to GPIO5 (SPI0 CS) and GPIO36 through a 2x2 jumper. It boots from
SPI-NOR or SPI-NAND depending on how the jumpers are connected.
The firmware can be flashed using U-boot web recovery from Siflower
vendor U-boot.
Link: https://github.com/openwrt/openwrt/pull/17115
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The same GPIO controller is found on all current Siflower SoCs,
with different number of GPIOs. Add ngpios property instead of
specifying it with dt match data.
Link: https://github.com/openwrt/openwrt/pull/17115
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Move SF19A2890 images into a separated .mk in preparation for
more subtargets.
Link: https://github.com/openwrt/openwrt/pull/17115
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The three packages base-files, libc and kernel are special, the former
can't be upgraded in place since it's content are modified on startup,
the latter two are virtual packages only used as constraints for the
package manager.
Historically base-files was "locked" via a special OPKG function, the
latter two were hidden from the package index and thereby never picked
as possible upgrade.
Time moved forward and we now have APK and tools like OWUT. The latter
compares available packages with installed packages and generates user
readable output, requiring versions for libc and kernel, too. At the
same time, APK uses a different looking mechanism, which is set during
installation instead of part of the package metadata.
In short, this patch adds version constraints to the three packages,
allowing them to be part of the package index.
Fixes: #17774Fixes: #17775Fixes: efahl/owut#31
Signed-off-by: Paul Spooren <mail@aparcar.org>
This reverts commit 3295f6f1c2.
It looks like the eeprom gets broken after this change.
I think this change was not tested on a real device before it was
merged.
The MAC addresses will be broken again after this revert.
Fixes: #17818
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Make use of ASCII env NVMEM driver for Linksys EAX devices. This also
fix a problem with Linksys EAX devices where the 2 MAC interface had the
same MAC address causing a conflicts with FDB entry. This got much more
present with the DSA conversion making the system not usable.
To fix this, increment + 1 the MAC address for the WAN interface.
Link: https://github.com/openwrt/openwrt/pull/17839
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add pending patch to support NVMEM ASCII ENV layout driver. This is a
generic driver to handle simple NVMEM partition that store environment
in a simple text format. This is the case for Linksys devinfo partition
that are litterally txt file with format "name=value\n"
Such driver works similar to u-boot,env with a similar format. While at
it also introduce a patch to generalize mac-base handling for also other
layout driver.
Link: https://github.com/openwrt/openwrt/pull/17839
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix broken WAN on Linksys EAX and Asrock G10 by incrementing the WAN
interface MAC address + 1. This caused conflicting entry in the FDB
table and caused the WAN port to malfunction with the DSA conversion.
Fixes: #17157Fixes: #15585Fixes: #16604
Link: https://github.com/openwrt/openwrt/pull/17839
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Two commits which made their way into Linux stable broke the SATA
support on the BPi-R64.
Fix this by reverting a node rename which broke DT-overlay application
and import a (still pending) patch re-adding the 'syscon' compatible to
the pciesys clock-controller which also contains phy-mode bits
referenced by the ahci_mtk driver expecting to access them using
syscon_regmap_lookup_by_phandle().
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
b11bff90f2ad r8169: add support for RTL8125BP rev.b
b3593df26ab1 r8169: add support for RTL8125D rev.b
b299ea006928 r8169: adjust version numbering for RTL8126
bb18265c3aba r8169: remove support for chip version 11
2e20bf8cc057 r8169: remove unused flag RTL_FLAG_TASK_RESET_NO_QUEUE_WAKE
e340bff27e63 r8169: copy vendor driver 2.5G/5G EEE advertisement constraints
The EEE advertisement patch has been reworked for linux v6.6 because
phy_set_eee_broken() is only present on linux >= v6.13 and eee_broken_modes
declaration has been converted to a bitmap, so linkmode_set_bit() can't be
used either.
e340bff27eed623fb8e3721aa69e70
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Following the initial support of the Cudy WR3000H with PHY C22 for the 2.5G WAN
interface, several improvements fixing issues with RealTek RTL8221B PHYs have
been merged.
Therefore we can now bring the DT in line with other equipment and declare the
2.5G WAN PHY as C45.
Fixes: 9d66b8b ("mediatek: filogic: Add support for cudy wr3000h")
Signed-off-by: Juan Pedro Paredes Caballero <juanpedro.paredes@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17739
[reword commit description]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
On some but not all devices using the RTL8221B 2.5GBit/s PHY the SerDes
setup sequence may hang under some circumstances (eg. <2500M link
partner present during boot).
RTL8221B-VB-CG 2.5Gbps PHY (C45) mdio-bus:01: rtl822xb_config_init failed: -110
Work-around the issue by performing a hardware reset and subsequent
retry of the SerDes setup, which seems to always succeed.
Doing this requires moving ALDPS setup to config_init (which is anyway
the better place for that) as it otherwise doesn't survive the reset.
Also disable listening on MDIO address 0 which may be used by other PHYs
despite being spec'ed as "broadcast address", as bus activity on address
0 may otherwise confuse the RealTek PHY for good reasons.
Tested-by: Luis Mita <luis@luismita.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
With the current LED configuration using "mxl,led-config", the WAN LED
stops working after the interface is brought down and up again.
Since the driver also properly supports PHY LEDs now, switch to that
instead. This makes the LED work properly, but requires configuration
from userspace.
Fixes: #17782
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/17785
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add kmod-drm-i915 to the default packages. It was build into the kernel
before and is now build as a kernel module.
Fixes: 77cfe8fd15 ("x86: make i915 as a kmod with required firmware")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://github.com/openwrt/openwrt/pull/17781
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use 'remove_oem_ubi_volume' function to remove OEM UBI volume before upgrade.
This allows to upgrade even if we have OEM firmware on the second partition.
Applies to Linksys MX4200/MX4300/MX5300/MX8500.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14720
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update u-boot env variables only when changes are made.
Applies to Linksys MX4200/MX4300/MX5300/MX8500.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14720
Signed-off-by: Robert Marko <robimarko@gmail.com>
Dual firmware devices like Linksys MX4200, MX4300, MX5300 and MX8500 use separate rootfs partition.
This option helps to keep all configuration during upgrade.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14720
Signed-off-by: Robert Marko <robimarko@gmail.com>
By switching to the new RTL8231 driver in commit b7af54d5c1 ("realtek:
Simple conversions to RTL8231 MFD driver"), the bootloader state of the
RTL8231's pins is now maintained. As the bootloader de-asserts the PoE
enable signal, this means PoE output is no longer available.
Add a gpio-hog with high output, restoring the line value from when the
pin was configured (by default) as an input with a pull-up resistor.
This will hard-enable the PoE output, but the individual ports can still
be administratively disabled by realtek-poe or a similar tool.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Switch the implementation for the RTL8231 GPIO expander to the new
driver.
This allows specifying the GPIO driving the RTL8231's reset as a proper
MDIO reset line, so the gpio-hog can be dropped. Since it was pinned at
a high level, the reset line is actually active-low (i.e. high when not
in reset).
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Update the common external GPIO DTSI file for the DGS-1210 devices to
use an MDIO device on the auxilairy MDIO bus, as the original driver was
doing behind the screen.
Switching to the new driver will allow for full pin-control and will no
longer reset pin config set by the bootloader.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The DTS file for the DGS-1210-10P is slightly different from the other
DGS-1210 devices, in that it didn't specify a gpio-restart node when it
was added. The gpio-restart has been found to work on the DGS-1210-10P
as well, so switch it over to the common definitions.
This converts the last device from the product family to the common
definition for the (external) GPIOs.
Tested-by: Michel Thill <jmthill@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The 'indirect-access-id' property on gpio0 is a remnant from the
original GPIO driver. This property has not been relevant on the SoC's
embedded GPIO controller for a long time, so just drop it.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The definition for the netgear_wndr4700 had two different
DEVICE_COMPAT_VERSION definitions.
In commit 5815884c3a ("apm821xx: migrate to DSA"), an additional
DEVICE_COMPAT_VERSION := 3.0 attribute was added to the device
definition. The old one with version 2.0 stayed and was defined later
overwriting the new one.
Replace the old version 2.0 with the new version 3.0
Fixes: 5815884c3a ("apm821xx: migrate to DSA")
Link: https://forum.openwrt.org/t/openwrt-24-10-0-rc6-sixth-release-candidate/222466/43
Link: https://github.com/openwrt/openwrt/pull/17741
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The STM32MP135F-DK board uses the LAN8742 PHY.
Enable CONFIG_SMSC_PHY to have full PHY support.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/17745
Signed-off-by: Robert Marko <robimarko@gmail.com>
ST1202 controller was added recently, but it was not disabled in the
generic config, so lets avoid individual target configs disabling it
and just disable it in generic config.
Link: https://github.com/openwrt/openwrt/pull/17746
Signed-off-by: Robert Marko <robimarko@gmail.com>
Replace eMMC support with upstream version where we declare dummy clock
and dummy regulator instead of a specific compatible. Also drop the
downstream patch for it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh cpufreq with merged upstream version. Also fix the PM Domain
rebased patch to correctly expose the symbol for non Mediatek target.
Update dtsi with new pm domain name.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
