qualcommax: add support for ELECOM WRC-X3000GS2
ELECOM WRC-X3000GS2 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
IPQ5018.
Specification:
- SoC : Qualcomm IPQ5018
- RAM : DDR3 256 MiB (Zentel A3T2GF40CBF-HP)
- Flash : SPI-NAND 128 MiB (Macronix MX35UF1G24AD-Z4I)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm IPQ5018 (SoC)
- 5 GHz : Qualcomm Atheros QCN6102
- Ethernet : 5x 10/100/1000 Mbps
- wan (phy) : Qualcomm IPQ5018 (SoC)
- lan (switch) : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO): 8x/3x
- UART : through-hole on PCB, 4pins near the barcode
- assignment : 3.3V, TX, RX, NC, GND from the barcode side
- settings : 115200n8
- Power : 12 VDC, 1 A (Max. 11.5W)
Flash instruction using initramfs-factory.bin image:
1. Boot WRC-X3000GS2 normally with router mode
2. Access to the WebUI ("http://192.168.2.1/") on the device and open
the firmware update page ("ファームウェア更新")
3. Select the OpenWrt factory.bin image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing
Switching to the stock firmware:
1. Load the elecom.sh script
. /lib/upgrade/elecom.sh
2. Check the current index of rootfs
bootconfig_rw_index 0:bootconfig rootfs
3. Set the index to inverted value
bootconfig_rw_index 0:bootconfig rootfs <value>
bootconfig_rw_index 0:bootconfig1 rootfs <value>
example:
- step2 returned "0":
bootconfig_rw_index 0:bootconfig rootfs 1
bootconfig_rw_index 0:bootconfig1 rootfs 1
- step2 returned "1":
bootconfig_rw_index 0:bootconfig rootfs 0
bootconfig_rw_index 0:bootconfig1 rootfs 0
4. Reboot
Partition Layout (Stock FW):
0x000000000000-0x000000080000 : "0:SBL1"
0x000000080000-0x000000100000 : "0:MIBIB"
0x000000100000-0x000000140000 : "0:BOOTCONFIG"
0x000000140000-0x000000180000 : "0:BOOTCONFIG1"
0x000000180000-0x000000280000 : "0:QSEE"
0x000000280000-0x000000380000 : "0:QSEE_1"
0x000000380000-0x0000003c0000 : "0:DEVCFG"
0x0000003c0000-0x000000400000 : "0:DEVCFG_1"
0x000000400000-0x000000440000 : "0:CDT"
0x000000440000-0x000000480000 : "0:CDT_1"
0x000000480000-0x000000500000 : "0:APPSBLENV"
0x000000500000-0x000000640000 : "0:APPSBL"
0x000000640000-0x000000780000 : "0:APPSBL_1"
0x000000780000-0x000000880000 : "0:ART"
0x000000880000-0x000000900000 : "0:TRAINING"
0x000000900000-0x000003c40000 : "rootfs"
0x000003c40000-0x000003fc0000 : "Config"
0x000003fc0000-0x000007300000 : "rootfs_1"
0x000007300000-0x000007680000 : "Config_2"
0x000007680000-0x000007b80000 : "Reserved"
0x000007b80000-0x000007c00000 : "FWHEADER"
0x000007c00000-0x000007c80000 : "Factory"
Known Issues:
- All Wi-Fi related peripherals are disabled.
This device has only 256 MiB RAM and it's too few for ath11k. To
prevent OOM when using LuCI or other softwares, disable Wi-Fi related
peripherals in device tree at the moment.
- This device has a Macronix MX35UF1G24AD SPI-NAND chip registered as
oobsize=128 in Linux Kernel. But using BCH8 breaks I/O on the chip
with the following errors, so this support uses BCH4 instead.
root@OpenWrt:~# strings /dev/mtdblock10
[26427.133154] mtdblock: MTD device '0:appsblenv' is NAND, please consider using UBI block devices instead.
[26427.134125] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 2
[26427.142240] I/O error, dev mtdblock10, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 2
[26427.151427] I/O error, dev mtdblock10, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 2
[26427.160440] I/O error, dev mtdblock10, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[26427.169619] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[26427.178083] Buffer I/O error on dev mtdblock10, logical block 0, async page read
Notes:
- This device has dual-boot feature and it's managed by the index in the
0:bootconfig and 0:bootconfig1 partitions.
MAC Addresses:
LAN : 38:97:A4:xx:xx:60 (0:APPSBLENV, "eth1addr"/"ethaddr" (text))
WAN : 38:97:A4:xx:xx:63 (0:APPSBLENV, "eth0addr" (text))
2.4 GHz: 38:97:A4:xx:xx:61 (0:APPSBLENV, "wifi0" (text))
5 GHz : 38:97:A4:xx:xx:62 (0:APPSBLENV, "wifi1" (text))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18543
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit is contained in:
INAGAKI Hiroshi
Robert Marko
parent
fc3ff2af0c
commit
3b7d72bc2e
8 changed files with 692 additions and 4 deletions
|
|
@ -38,6 +38,7 @@ ALLWIFIBOARDS:= \
|
|||
dynalink_dl-wrx36 \
|
||||
edgecore_eap102 \
|
||||
edimax_cax1800 \
|
||||
elecom_wrc-x3000gs2 \
|
||||
glinet_gl-ax1800 \
|
||||
glinet_gl-axt1800 \
|
||||
glinet_gl-b3000 \
|
||||
|
|
@ -189,6 +190,7 @@ $(eval $(call generate-ipq-wifi-package,compex_wpq873,Compex WPQ-873))
|
|||
$(eval $(call generate-ipq-wifi-package,dynalink_dl-wrx36,Dynalink DL-WRX36))
|
||||
$(eval $(call generate-ipq-wifi-package,edgecore_eap102,Edgecore EAP102))
|
||||
$(eval $(call generate-ipq-wifi-package,edimax_cax1800,Edimax CAX1800))
|
||||
$(eval $(call generate-ipq-wifi-package,elecom_wrc-x3000gs2,ELECOM WRC-X3000GS2))
|
||||
$(eval $(call generate-ipq-wifi-package,glinet_gl-ax1800,GL.iNet GL-AX1800))
|
||||
$(eval $(call generate-ipq-wifi-package,glinet_gl-axt1800,GL.iNet GL-AXT1800))
|
||||
$(eval $(call generate-ipq-wifi-package,glinet_gl-b3000,GL.iNet GL-B3000))
|
||||
|
|
|
|||
|
|
@ -0,0 +1,503 @@
|
|||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "ipq5018.dtsi"
|
||||
#include "ipq5018-ess.dtsi"
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
/ {
|
||||
model = "ELECOM WRC-X3000GS2";
|
||||
compatible = "elecom,wrc-x3000gs2", "qcom,ipq5018";
|
||||
|
||||
aliases {
|
||||
serial0 = &blsp1_uart1;
|
||||
led-boot = &led_power_green;
|
||||
led-failsafe = &led_power_red;
|
||||
led-running = &led_power_green;
|
||||
led-upgrade = &led_power_green;
|
||||
label-mac-device = <&dp1>;
|
||||
};
|
||||
|
||||
chosen {
|
||||
bootargs-append = " root=/dev/ubiblock0_1 coherent_pool=2M";
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
keys {
|
||||
compatible = "gpio-keys";
|
||||
pinctrl-0 = <&button_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
switch-router {
|
||||
label = "router";
|
||||
gpios = <&tlmm 14 GPIO_ACTIVE_HIGH>;
|
||||
linux,code = <BTN_0>;
|
||||
linux,input-type = <EV_SW>;
|
||||
};
|
||||
|
||||
reset-button {
|
||||
label = "reset";
|
||||
gpios = <&tlmm 22 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_RESTART>;
|
||||
};
|
||||
|
||||
wps-button {
|
||||
label = "wps";
|
||||
gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
|
||||
linux,code = <KEY_WPS_BUTTON>;
|
||||
};
|
||||
};
|
||||
|
||||
leds {
|
||||
compatible = "gpio-leds";
|
||||
pinctrl-0 = <&led_pins>;
|
||||
pinctrl-names = "default";
|
||||
|
||||
led-0 {
|
||||
gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_WPS;
|
||||
};
|
||||
|
||||
led_power_green: led-1 {
|
||||
gpios = <&tlmm 13 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_POWER;
|
||||
};
|
||||
|
||||
led_power_red: led-2 {
|
||||
gpios = <&tlmm 16 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_POWER;
|
||||
};
|
||||
|
||||
led-3 {
|
||||
gpios = <&tlmm 24 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_WLAN_5GHZ;
|
||||
linux,default-trigger = "phy1radio";
|
||||
};
|
||||
|
||||
led-4 {
|
||||
gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_WLAN_5GHZ;
|
||||
};
|
||||
|
||||
led-5 {
|
||||
gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_WLAN_2GHZ;
|
||||
linux,default-trigger = "phy0radio";
|
||||
};
|
||||
|
||||
led-6 {
|
||||
gpios = <&tlmm 28 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
function = LED_FUNCTION_WLAN_2GHZ;
|
||||
};
|
||||
|
||||
led-7 {
|
||||
gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
function = LED_FUNCTION_WAN;
|
||||
};
|
||||
};
|
||||
|
||||
reserved-memory {
|
||||
q6_mem_regions: q6_mem_regions@4b000000 {
|
||||
no-map;
|
||||
reg = <0x0 0x4b000000 0x0 0x3000000>;
|
||||
status = "disabled";
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&sleep_clk {
|
||||
clock-frequency = <32000>;
|
||||
};
|
||||
|
||||
&xo_board_clk {
|
||||
clock-frequency = <24000000>;
|
||||
};
|
||||
|
||||
&blsp1_uart1 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&serial_0_pins>;
|
||||
pinctrl-names = "default";
|
||||
};
|
||||
|
||||
&crypto {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&cryptobam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&prng {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qfprom {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_bam {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&qpic_nand {
|
||||
pinctrl-0 = <&qpic_pins>;
|
||||
pinctrl-names = "default";
|
||||
status = "okay";
|
||||
|
||||
flash@0 {
|
||||
compatible = "spi-nand";
|
||||
reg = <0>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
nand-ecc-engine = <&qpic_nand>;
|
||||
|
||||
/* strength=8 breaks NAND I/O, use 4 instead */
|
||||
nand-ecc-strength = <4>;
|
||||
nand-ecc-step-size = <512>;
|
||||
nand-bus-width = <8>;
|
||||
|
||||
partitions {
|
||||
compatible = "qcom,smem-part";
|
||||
|
||||
partition-0-appsblenv {
|
||||
compatible = "fixed-partitions";
|
||||
label = "0:appsblenv";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "env-data";
|
||||
reg = <0x0 0x40000>;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "u-boot,env";
|
||||
|
||||
macaddr_appsblenv_ethaddr: ethaddr {
|
||||
compatible = "mac-base";
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&switch {
|
||||
status = "okay";
|
||||
|
||||
switch_mac_mode = <MAC_MODE_SGMII_CHANNEL0>;
|
||||
|
||||
qcom,port_phyinfo {
|
||||
port@0 {
|
||||
port_id = <1>;
|
||||
mdiobus = <&mdio0>;
|
||||
phy_address = <7>;
|
||||
};
|
||||
|
||||
port@1 {
|
||||
port_id = <2>;
|
||||
forced-speed = <1000>;
|
||||
forced-duplex = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&dp1 {
|
||||
status = "okay";
|
||||
|
||||
label = "wan";
|
||||
nvmem-cells = <&macaddr_appsblenv_ethaddr 3>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
&dp2 {
|
||||
status = "okay";
|
||||
|
||||
nvmem-cells = <&macaddr_appsblenv_ethaddr 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
&mdio0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&mdio1 {
|
||||
status = "okay";
|
||||
|
||||
pinctrl-0 = <&mdio1_pins>, <&switch_reset_pins>;
|
||||
pinctrl-names = "default";
|
||||
reset-gpios = <&tlmm 39 GPIO_ACTIVE_LOW>;
|
||||
|
||||
qca8337_0: ethernet-phy@0 {
|
||||
reg = <0>;
|
||||
};
|
||||
|
||||
qca8337_1: ethernet-phy@1 {
|
||||
reg = <1>;
|
||||
};
|
||||
|
||||
qca8337_2: ethernet-phy@2 {
|
||||
reg = <2>;
|
||||
};
|
||||
|
||||
qca8337_3: ethernet-phy@3 {
|
||||
reg = <3>;
|
||||
};
|
||||
|
||||
ethernet-switch@18 {
|
||||
compatible = "qca,qca8337";
|
||||
reg = <0x18>;
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
label = "lan1";
|
||||
phy-handle = <&qca8337_0>;
|
||||
};
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
label = "lan2";
|
||||
phy-handle = <&qca8337_1>;
|
||||
};
|
||||
|
||||
port@3 {
|
||||
reg = <3>;
|
||||
label = "lan3";
|
||||
phy-handle = <&qca8337_2>;
|
||||
};
|
||||
|
||||
port@4 {
|
||||
reg = <4>;
|
||||
label = "lan4";
|
||||
phy-handle = <&qca8337_3>;
|
||||
};
|
||||
|
||||
port@6 {
|
||||
reg = <6>;
|
||||
phy-mode = "sgmii";
|
||||
ethernet = <&dp2>;
|
||||
qca,sgmii-enable-pll;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&tlmm {
|
||||
button_pins: button-state {
|
||||
button-pins {
|
||||
pins = "gpio22", "gpio38";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
switch-pins {
|
||||
pins = "gpio14";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
|
||||
led_pins: led-state {
|
||||
pins = "gpio12", "gpio13", "gpio16", "gpio24",
|
||||
"gpio25", "gpio26", "gpio28", "gpio46";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-down;
|
||||
};
|
||||
|
||||
mdio1_pins: mdio-state {
|
||||
mdc-pins {
|
||||
pins = "gpio36";
|
||||
function = "mdc";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
|
||||
mdio-pins {
|
||||
pins = "gpio37";
|
||||
function = "mdio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-up;
|
||||
};
|
||||
};
|
||||
|
||||
qpic_pins: qpic-state {
|
||||
clock-pins {
|
||||
pins = "gpio9";
|
||||
function = "qspi_clk";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
cs-pins {
|
||||
pins = "gpio8";
|
||||
function = "qspi_cs";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
data-pins {
|
||||
pins = "gpio4", "gpio5", "gpio6", "gpio7";
|
||||
function = "qspi_data";
|
||||
drive-strength = <8>;
|
||||
bias-disable;
|
||||
};
|
||||
};
|
||||
|
||||
serial_0_pins: uart0-state {
|
||||
pins = "gpio20", "gpio21";
|
||||
function = "blsp0_uart0";
|
||||
bias-disable;
|
||||
};
|
||||
|
||||
switch_reset_pins: switch-reset-state {
|
||||
pins = "gpio39";
|
||||
function = "gpio";
|
||||
drive-strength = <8>;
|
||||
bias-pull-down;
|
||||
};
|
||||
};
|
||||
|
||||
&tsens {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
/*
|
||||
* ath11k Wi-Fi consumes too large memory spaces and too few spaces are
|
||||
* available for users. To prevent OOM when using LuCI or other softwares,
|
||||
* disable Wi-Fi related peripherals at the moment.
|
||||
*/
|
||||
&q6v5_wcss {
|
||||
status = "disabled";
|
||||
|
||||
memory-region = <&q6_mem_regions>;
|
||||
firmware-name = "ath11k/IPQ5018/hw1.0/q6_fw.mdt",
|
||||
"ath11k/IPQ5018/hw1.0/m3_fw.mdt",
|
||||
"ath11k/QCN6122/hw1.0/m3_fw.mdt";
|
||||
|
||||
boot-args = <0x2 4 2 18 0 0>; /* pcie:1, len:4, updid:2, reset:gpio18 */
|
||||
|
||||
q6_wcss_pd1: pd-1 {
|
||||
firmware-name = "ath11k/IPQ5018/hw1.0/q6_fw.mdt";
|
||||
|
||||
resets =
|
||||
<&gcc GCC_WCSSAON_RESET>,
|
||||
<&gcc GCC_WCSS_BCR>,
|
||||
<&gcc GCC_CE_BCR>;
|
||||
reset-names =
|
||||
"wcss_aon_reset",
|
||||
"wcss_reset",
|
||||
"ce_reset";
|
||||
|
||||
clocks =
|
||||
<&gcc GCC_WCSS_AHB_S_CLK>,
|
||||
<&gcc GCC_WCSS_ACMT_CLK>,
|
||||
<&gcc GCC_WCSS_AXI_M_CLK>;
|
||||
clock-names =
|
||||
"gcc_wcss_ahb_s_clk",
|
||||
"gcc_wcss_acmt_clk",
|
||||
"gcc_wcss_axi_m_clk";
|
||||
|
||||
interrupts-extended =
|
||||
<&wcss_smp2p_in 8 IRQ_TYPE_NONE>,
|
||||
<&wcss_smp2p_in 9 IRQ_TYPE_NONE>,
|
||||
<&wcss_smp2p_in 12 IRQ_TYPE_NONE>,
|
||||
<&wcss_smp2p_in 11 IRQ_TYPE_NONE>;
|
||||
interrupt-names =
|
||||
"fatal",
|
||||
"ready",
|
||||
"spawn-ack",
|
||||
"stop-ack";
|
||||
|
||||
qcom,smem-states =
|
||||
<&wcss_smp2p_out 8>,
|
||||
<&wcss_smp2p_out 9>,
|
||||
<&wcss_smp2p_out 10>;
|
||||
qcom,smem-state-names =
|
||||
"shutdown",
|
||||
"stop",
|
||||
"spawn";
|
||||
};
|
||||
|
||||
q6_wcss_pd2: pd-2 {
|
||||
firmware-name = "ath11k/IPQ5018/hw1.0/q6_fw.mdt";
|
||||
|
||||
interrupts-extended =
|
||||
<&wcss_smp2p_in 16 IRQ_TYPE_NONE>,
|
||||
<&wcss_smp2p_in 17 IRQ_TYPE_NONE>,
|
||||
<&wcss_smp2p_in 20 IRQ_TYPE_NONE>,
|
||||
<&wcss_smp2p_in 19 IRQ_TYPE_NONE>;
|
||||
interrupt-names =
|
||||
"fatal",
|
||||
"ready",
|
||||
"spawn-ack",
|
||||
"stop-ack";
|
||||
|
||||
qcom,smem-states =
|
||||
<&wcss_smp2p_out 16>,
|
||||
<&wcss_smp2p_out 17>,
|
||||
<&wcss_smp2p_out 18>;
|
||||
qcom,smem-state-names =
|
||||
"shutdown",
|
||||
"stop",
|
||||
"spawn";
|
||||
};
|
||||
};
|
||||
|
||||
&wifi0 {
|
||||
qcom,rproc = <&q6_wcss_pd1>;
|
||||
qcom,userpd-subsys-name = "q6v5_wcss_userpd1";
|
||||
qcom,ath11k-calibration-variant = "ELECOM-WRC-X3000GS2";
|
||||
qcom,ath11k-fw-memory-mode = <2>;
|
||||
qcom,bdf-addr = <0x4c400000>;
|
||||
|
||||
ieee80211-freq-limit = <2400000 2483000>;
|
||||
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&wifi1 {
|
||||
qcom,rproc = <&q6_wcss_pd2>;
|
||||
qcom,userpd-subsys-name = "q6v5_wcss_userpd2";
|
||||
qcom,ath11k-calibration-variant = "ELECOM-WRC-X3000GS2";
|
||||
qcom,ath11k-fw-memory-mode = <2>;
|
||||
qcom,bdf-addr = <0x4d100000>;
|
||||
qcom,m3-dump-addr = <0x4df00000>;
|
||||
|
||||
ieee80211-freq-limit = <5150000 5730000>;
|
||||
|
||||
status = "disabled";
|
||||
};
|
||||
|
|
@ -1,5 +1,40 @@
|
|||
DEVICE_VARS += BOOT_SCRIPT
|
||||
|
||||
define Build/mstc-header
|
||||
$(eval version=$(1))
|
||||
gzip -c $@ | tail -c8 > $@.crclen
|
||||
( \
|
||||
printf "CMOC"; \
|
||||
tail -c+5 $@.crclen; head -c4 $@.crclen; \
|
||||
printf '$(call toupper,$(LINUX_KARCH)) $(VERSION_DIST) Linux-$(LINUX_VERSION)' | \
|
||||
dd bs=64 count=1 conv=sync 2>/dev/null; \
|
||||
printf "$(version)" | \
|
||||
dd bs=64 count=1 conv=sync 2>/dev/null; \
|
||||
dd if=/dev/zero bs=884 count=1 2>/dev/null; \
|
||||
cat $@; \
|
||||
) > $@.new
|
||||
mv $@.new $@
|
||||
rm -f $@.crclen
|
||||
endef
|
||||
|
||||
define Device/elecom_wrc-x3000gs2
|
||||
$(call Device/FitImageLzma)
|
||||
$(call Device/UbiFit)
|
||||
DEVICE_VENDOR := ELECOM
|
||||
DEVICE_MODEL := WRC-X3000GS2
|
||||
DEVICE_DTS_CONFIG := config@mp03.3
|
||||
SOC := ipq5018
|
||||
BLOCKSIZE := 128k
|
||||
PAGESIZE := 2048
|
||||
IMAGE_SIZE := 52480k
|
||||
NAND_SIZE := 128m
|
||||
IMAGES += factory.bin
|
||||
IMAGE/factory.bin := append-ubi | qsdk-ipq-factory-nand | \
|
||||
mstc-header 4.04(XZF.0)b90 | elecom-product-header WRC-X3000GS2
|
||||
DEVICE_PACKAGES := ath11k-firmware-qcn6122 ipq-wifi-elecom_wrc-x3000gs2
|
||||
endef
|
||||
TARGET_DEVICES += elecom_wrc-x3000gs2
|
||||
|
||||
define Device/glinet_gl-b3000
|
||||
$(call Device/FitImage)
|
||||
DEVICE_VENDOR := GL.iNet
|
||||
|
|
|
|||
|
|
@ -9,6 +9,9 @@ board_config_update
|
|||
board=$(board_name)
|
||||
|
||||
case "$board" in
|
||||
elecom,wrc-x3000gs2)
|
||||
ucidef_set_led_netdev "wan" "WAN" "green:wan" "wan" "tx rx link_10 link_100 link_1000"
|
||||
;;
|
||||
linksys,mr5500)
|
||||
ucidef_set_led_netdev "lan1-port-link" "LAN1-PORT-LINK" "qca8k-0.0:00:green:lan" "lan1" "link_10 link_100 link_1000"
|
||||
ucidef_set_led_netdev "lan1-port-activity" "LAN1-PORT-ACTIVITY" "qca8k-0.0:00:amber:lan" "lan1" "tx rx"
|
||||
|
|
|
|||
|
|
@ -7,12 +7,13 @@ ipq50xx_setup_interfaces()
|
|||
{
|
||||
local board="$1"
|
||||
case $board in
|
||||
glinet,gl-b3000)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2" "wan"
|
||||
;;
|
||||
elecom,wrc-x3000gs2|\
|
||||
linksys,mr5500)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
|
||||
;;
|
||||
glinet,gl-b3000)
|
||||
ucidef_set_interfaces_lan_wan "lan1 lan2" "wan"
|
||||
;;
|
||||
linksys,mx2000|\
|
||||
linksys,mx5500|\
|
||||
linksys,spnmx56)
|
||||
|
|
|
|||
|
|
@ -9,6 +9,12 @@ board=$(board_name)
|
|||
case "$FIRMWARE" in
|
||||
"ath11k/IPQ5018/hw1.0/cal-ahb-c000000.wifi.bin")
|
||||
case "$board" in
|
||||
elecom,wrc-x3000gs2)
|
||||
caldata_extract "0:art" 0x1000 0x20000
|
||||
wlan_mac=$(mtd_get_mac_ascii 0:appsblenv wifi0)
|
||||
ath11k_patch_mac $wlan_mac 0
|
||||
ath11k_set_macflag
|
||||
;;
|
||||
glinet,gl-b3000)
|
||||
caldata_extract "0:art" 0x1000 0x20000
|
||||
ath11k_patch_mac $(macaddr_add $(get_mac_label_dt) 3) 0
|
||||
|
|
@ -28,6 +34,12 @@ case "$FIRMWARE" in
|
|||
;;
|
||||
"ath11k/QCN6122/hw1.0/cal-ahb-b00a040.wifi1.bin")
|
||||
case "$board" in
|
||||
elecom,wrc-x3000gs2)
|
||||
caldata_extract "0:art" 0x26800 0x20000
|
||||
wlan_mac=$(mtd_get_mac_ascii 0:appsblenv wifi1)
|
||||
ath11k_patch_mac $wlan_mac 0
|
||||
ath11k_set_macflag
|
||||
;;
|
||||
glinet,gl-b3000)
|
||||
caldata_extract "0:art" 0x26800 0x20000
|
||||
ath11k_patch_mac $(macaddr_add $(get_mac_label_dt) 4) 0
|
||||
|
|
|
|||
119
target/linux/qualcommax/ipq50xx/base-files/lib/upgrade/elecom.sh
Normal file
119
target/linux/qualcommax/ipq50xx/base-files/lib/upgrade/elecom.sh
Normal file
|
|
@ -0,0 +1,119 @@
|
|||
. /lib/functions.sh
|
||||
|
||||
bootconfig_find_entry() {
|
||||
local cfgbin="$1"
|
||||
local partname="$2"
|
||||
local i part parts offset
|
||||
|
||||
parts=$(hexdump -n 4 -s 8 -e '1/4 "%d"' "$cfgbin")
|
||||
# partition count: <= 10
|
||||
[ -z "$parts" ] || [ "$parts" = "0" ] || [ "$parts" -gt "10" ] && \
|
||||
return 1
|
||||
|
||||
for i in $(seq 1 $parts); do
|
||||
offset=$((0xc + 0x14 * (i - 1)))
|
||||
part=$(dd if="$cfgbin" iflag=skip_bytes \
|
||||
skip=$offset bs=16 count=1 2>/dev/null)
|
||||
if [ "$part" = "$partname" ]; then
|
||||
printf "0x%08x" $offset
|
||||
return
|
||||
fi
|
||||
done
|
||||
|
||||
return 1
|
||||
}
|
||||
|
||||
# Read or update an entry in Qualcomm bootconfig partition
|
||||
#
|
||||
# parameters:
|
||||
# $1: partition name of bootconfig (ex.: "0:bootconfig", "0:bootconfig1", etc)
|
||||
# $2: entry name in bootconfig (ex.: "0:hlos", "rootfs", etc)
|
||||
# $3: index to set for the entry (0/1)
|
||||
#
|
||||
# operations:
|
||||
# read : bootconfig_rw_index <bootconfig> <entry>
|
||||
# write: bootconfig_rw_index <bootconfig> <entry> <index>
|
||||
bootconfig_rw_index() {
|
||||
local bootcfg="$1"
|
||||
local partname="$2"
|
||||
local index="$3"
|
||||
local mtddev
|
||||
local offset
|
||||
local current
|
||||
|
||||
if [ -z "$bootcfg" ] || [ -z "$partname" ]; then
|
||||
echo "no value specified for bootconfig or partition entry"
|
||||
return 1
|
||||
fi
|
||||
|
||||
case "$index" in
|
||||
0|1|"") ;;
|
||||
*) echo "invalid bootconfig index specified \"$index\""; return 1 ;;
|
||||
esac
|
||||
|
||||
mtddev="$(find_mtd_part $bootcfg)"
|
||||
[ -z "$mtddev" ] && \
|
||||
return 1
|
||||
|
||||
dd if=$mtddev of=/tmp/${mtddev##*/} bs=1k
|
||||
|
||||
offset=$(bootconfig_find_entry "/tmp/${mtddev##*/}" $partname) || return 1
|
||||
current=$(hexdump -n 4 -s $((offset + 0x10)) -e '1/4 "%d"' /tmp/${mtddev##*/})
|
||||
|
||||
[ -z "$index" ] && \
|
||||
echo "$current" && return 0
|
||||
|
||||
if [ "$current" != "$index" ]; then
|
||||
printf "\x$index" | \
|
||||
dd of=$mtddev conv=notrunc bs=1 seek=$((offset + 0x10))
|
||||
fi
|
||||
}
|
||||
|
||||
# Qcom U-Boot always sets a name of current active partition to "rootfs" and
|
||||
# inactive partition is named as "rootfs_1", in the smem partition table.
|
||||
# When the second partition is active, "rootfs" and "rootfs_1" are swapped.
|
||||
smempart_next_root() {
|
||||
local index="$1"
|
||||
local root_idx="$(find_mtd_index rootfs)"
|
||||
local root1_idx="$(find_mtd_index rootfs_1)"
|
||||
local root_offset root1_offset
|
||||
|
||||
[ -z "$root_idx" ] || [ -z "$root1_idx" ] && \
|
||||
return 1
|
||||
|
||||
root_offset=$(cat /sys/block/mtdblock$root_idx/device/offset)
|
||||
root1_offset=$(cat /sys/block/mtdblock$root1_idx/device/offset)
|
||||
|
||||
case "$index" in
|
||||
0)
|
||||
[ "$root_offset" -lt "$root1_offset" ] && \
|
||||
echo "rootfs" || \
|
||||
echo "rootfs_1"
|
||||
;;
|
||||
1)
|
||||
[ "$root_offset" -lt "$root1_offset" ] && \
|
||||
echo "rootfs_1" || \
|
||||
echo "rootfs"
|
||||
;;
|
||||
*)
|
||||
echo "invalid index specified..."
|
||||
return 1
|
||||
;;
|
||||
esac
|
||||
}
|
||||
|
||||
elecom_upgrade_prepare() {
|
||||
local index
|
||||
|
||||
if ! index=$(bootconfig_rw_index "0:bootconfig" rootfs); then
|
||||
v "failed to read bootconfig index..."
|
||||
nand_do_upgrade_failed
|
||||
fi
|
||||
|
||||
if ! CI_UBIPART=$(smempart_next_root $index); then
|
||||
v "failed to get next root..."
|
||||
nand_do_upgrade_failed
|
||||
fi
|
||||
|
||||
v "next rootfs: $index (current: $CI_UBIPART)"
|
||||
}
|
||||
|
|
@ -1,7 +1,7 @@
|
|||
PART_NAME=firmware
|
||||
REQUIRE_IMAGE_METADATA=1
|
||||
|
||||
RAMFS_COPY_BIN='dumpimage fw_printenv fw_setenv head'
|
||||
RAMFS_COPY_BIN='dumpimage fw_printenv fw_setenv head seq'
|
||||
RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
|
||||
|
||||
remove_oem_ubi_volume() {
|
||||
|
|
@ -71,6 +71,19 @@ platform_check_image() {
|
|||
|
||||
platform_do_upgrade() {
|
||||
case "$(board_name)" in
|
||||
elecom,wrc-x3000gs2)
|
||||
local delay index
|
||||
|
||||
delay=$(fw_printenv bootdelay)
|
||||
[ -z "$delay" ] || [ "$delay" -eq "0" ] && \
|
||||
fw_setenv bootdelay 3
|
||||
|
||||
elecom_upgrade_prepare
|
||||
|
||||
remove_oem_ubi_volume ubi_rootfs
|
||||
remove_oem_ubi_volume wifi_fw
|
||||
nand_do_upgrade "$1"
|
||||
;;
|
||||
glinet,gl-b3000)
|
||||
glinet_do_upgrade "$1"
|
||||
;;
|
||||
|
|
|
|||
Loading…
Reference in a new issue