PCIe bridge nodes are now present in the SoC DTSI, so drop our downstream
ones as otherwise ath1*k BDF matching will fail.
Link: https://github.com/openwrt/openwrt/pull/18789
Signed-off-by: Robert Marko <robimarko@gmail.com>
It seems that bus-range property was missed for the PCIe bridges on
IPQ50xx, thus causing DTC to warn on any bus adress used on nodes
under the PCIe bridges.
Link: https://github.com/openwrt/openwrt/pull/18789
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the latest v9 PCIe DTS patch that is pending upstream, notable change
being that it includes PCIe bridge nodes.
Link: https://github.com/openwrt/openwrt/pull/18789
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specify 4-bit ECC strength instead of 8-bit, to resolve NAND I/O errors
on ELECOM WRC-X3000GS2.
ELECOM WRC-X3000GS2 has a Macronix MX35UF1G24AD SPI-NAND chip as a flash
storage. That chip is registered as a chip that has 128 bytes OOB and
requires 8-bit ECC, and described as the same in the Macronix's datasheet.
But on WRC-X3000GS2, 8-bit ECC breaks NAND I/O on mtdblock devices with
the following errors and 4-bit ECC needs to be used to resolve this issue.
current (ECC strength=8):
```
[ 1.401566] 0x000000480000-0x000000500000 : "0:appsblenv"
[ 1.407128] 1 fixed-partitions partitions found on MTD device 0:appsblenv
[ 1.410663] Creating 1 MTD partitions on "0:appsblenv":
[ 1.417359] 0x000000000000-0x000000040000 : "env-data"
[ 1.479865] u-boot-env-layout: probe of 79b0000.qpic-nand:flash@0:partitions:partition-0-appsblenv:partition@0:nvmem-layout failed with error -74
root@OpenWrt:~# strings /dev/mtdblock10
[ 55.693754] mtdblock: MTD device '0:appsblenv' is NAND, please consider using UBI block devices instead.
[ 55.694660] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 2
[ 55.703147] I/O error, dev mtdblock10, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 2
[ 55.711884] I/O error, dev mtdblock10, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 2
[ 55.720778] I/O error, dev mtdblock10, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[ 55.730310] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[ 55.738607] Buffer I/O error on dev mtdblock10, logical block 0, async page read
```
after fixing (ECC strength=4):
```
[ 1.402301] 0x000000480000-0x000000500000 : "0:appsblenv"
[ 1.407909] 1 fixed-partitions partitions found on MTD device 0:appsblenv
[ 1.411370] Creating 1 MTD partitions on "0:appsblenv":
[ 1.418075] 0x000000000000-0x000000040000 : "env-data"
(no error)
root@OpenWrt:~# strings /dev/mtdblock10
[ 39.131008] mtdblock: MTD device '0:appsblenv' is NAND, please consider using UBI block devices instead.
bootcmd=bootipq
baudrate=115200
wifi2=7C:F8:54:01:BD:F3
CRASH_COUNT=0
...
```
Fixes: 01b72ce61e ("qualcommax: ipq50xx: remove ECC user config from board files")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18770
Signed-off-by: Robert Marko <robimarko@gmail.com>
Passing QMP pipe clocks was upstreamed, but it requires conversion single
QMP node, so backport both of those instead of our downstream patch.
Signed-off-by: Robert Marko <robimarko@gmail.com>
In order to free up some more number space, simply renumber existing
upstreamed patches starting from 0 again.
Signed-off-by: Robert Marko <robimarko@gmail.com>
With the spi-qpic-snand driver now supporting reading ECC requirements
from the NAND chip itself, there's no need to set those in the DTS
anymore avoiding issues with devices of the same revision using
different NAND types with varying ECC requirements.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18723
Signed-off-by: Robert Marko <robimarko@gmail.com>
Updating the spi-qpic-snand driver with the latest patches sent
upstream and remove custom patches.
These patches add error handling fixes, use of right read location in
read ops, removal of unused variable, ability to read user config and
nand chip requirements, and support for 8bits ECC strength.
Tested on: Gl.iNet GL-B3000 & Linksys MR5500, MX2000, MX5500, SPNMX56
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18723
Signed-off-by: Robert Marko <robimarko@gmail.com>
Multiple conf support was upstreamed into kernel 6.10, so lets use the
upstreamed patches and mark them as so.
Signed-off-by: Robert Marko <robimarko@gmail.com>
MP5496 patches are not part of 6.15, but rather will be part of 6.16 as
they are no in 6.15 RC releases but they are in linux-next.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This additional board.d script creates the "/tmp/sysinfo/oem_name" file
and populates it with the proper OEM "supported_devices" metadata entry
to be used by the new fwtool.sh oem detection feature.
(#18554): add oem image dectection to fwtool.sh
Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18656
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix DTB warning when compiling an image by adding the missing hash sign
of adress-cells in the usb_dwc node.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18672
Signed-off-by: Robert Marko <robimarko@gmail.com>
Commit fc3ff2af0c introduced reading
ECC strength from the device tree. Linksys MR5500 uses the mx-base dtsi
which was originally developed for Linksys MX2000 and MX5500 where the
ECC strength is set to 8. Correct this and set it to strength of 4 as
per the NAND specs for Gigadevice GD5F2GQ5REYIH.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18672
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit 34e5bc4af54d366147a83904c094d54fec7fb025.
While fixing support for 2.5Gbps mode on uniphy in phy to phy link
setups, it inadvertently broke fixed link scenario. So let's revert this
commit until there's a fix that doesn't impact fixed links.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18668
Signed-off-by: Robert Marko <robimarko@gmail.com>
fixes the following warning seen in bootlog
"Kernel image misaligned at boot, please fix your bootloader!"
Fixes: 3307fe8 ("qualcommax: ipq50xx: add support for GL.iNET GL-B3000")
Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18658
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix the resets of the GE_PHY and Uniphy found on the IPQ5018 SoC.
Bitmasks are used to perform multiple resets simultaneously, including
the RX and TX clocks. This enables the Uniphy to properly shift between
SGMII/1G and SGMII+/2.5G modes.
While at it, properly reorder the patches, and rename some to follow
naming standards.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18638
Signed-off-by: Robert Marko <robimarko@gmail.com>
As part of the previous commit to add the #clock-cells property to the
GE PHY, the PHY was inadvertently moved under the second mdio node in
the dtsi, and therefore broke the init sequence as the driver was trying
to use the wrong mdio bus to set the init values (ex. DAC, MSE, and AZ).
So let's move it back under the right mdio node and, while at it, pad
the register addresses to 8 hex numbers and re-order properties in line
with Linux DTS coding standards.
Fixes: 6782d0e66f
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18634
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix swapped WLAN LEDs and move to blue LEDs to match stock behavior. Add LAN LED mappings.
Signed-off-by: Erik Servili <serverror@serverror.com>
Link: https://github.com/openwrt/openwrt/pull/18624
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop the firmware image entry "factory.ubi" from IMAGES for ELECOM
WRC-X3000GS2.
`Device/UbiFit` is added in the early stage of working for adding
support of the device, but finally, only `KERNEL_IN_UBI` is neccesary
and factory.ubi is not. So `Device/UbiFit` should have been replaced
to `KERNEL_IN_UBI` but it was forgotten.
Fixes: 3b7d72bc2e ("qualcommax: add support for ELECOM WRC-X3000GS2")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18611
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix nand-ecc-strength property in the spi-nand node of GL-iNet GL-B3000
to 4, to solve the following ECC error on that spi-nand chip.
[ 1.551618] ubi0: attaching mtd11
[ 1.552331] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 0:0, read only 64 bytes, retry
[ 1.554455] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 0:0, read only 64 bytes, retry
[ 1.565931] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 0:0, read only 64 bytes, retry
[ 1.576568] ubi0 error: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 0:0, read 64 bytes
[ 1.587146] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.6.87 #0
[ 1.597153] Hardware name: GL.iNet GL-B3000 (DT)
[ 1.602881] Call trace:
[ 1.607739] dump_backtrace+0xa0/0xe0
[ 1.609910] show_stack+0x18/0x24
[ 1.613728] dump_stack_lvl+0x48/0x60
[ 1.617027] dump_stack+0x18/0x24
[ 1.620672] ubi_io_read+0x11c/0x32c
[ 1.623972] ubi_io_read_ec_hdr+0x50/0x1f0
[ 1.627618] ubi_attach+0x35c/0x133c
[ 1.631524] ubi_attach_mtd_dev+0x494/0xaf4
[ 1.635257] ubi_init_attach+0xac/0x2e4
[ 1.639163] do_one_initcall+0x6c/0x1fc
[ 1.642983] kernel_init_freeable+0x204/0x2e4
[ 1.646803] kernel_init+0x28/0x1dc
[ 1.651316] ret_from_fork+0x10/0x20
The GL-B3000 has a Winbond W25N01GW and the spare size (oobsize) of it
is 64. So the maximum available ECC strength with the qpic-snand driver
is 4 but not 8.
The "nand-ecc-strength" property was not used before the commit
fc3ff2af0c ("qualcommax: allow overriding ECC strength for qpic-snand")
and calculated from the registered spare size in the Linux Kernel. As a
result, we had no issues on the GL-B3000 with the wrong ECC strength
value.
Fixes: 3307fe8ee4 ("qualcommax: ipq50xx: add support for GL.iNET GL-B3000")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18595
Signed-off-by: Robert Marko <robimarko@gmail.com>
ELECOM WRC-X3000GS2 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
IPQ5018.
Specification:
- SoC : Qualcomm IPQ5018
- RAM : DDR3 256 MiB (Zentel A3T2GF40CBF-HP)
- Flash : SPI-NAND 128 MiB (Macronix MX35UF1G24AD-Z4I)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm IPQ5018 (SoC)
- 5 GHz : Qualcomm Atheros QCN6102
- Ethernet : 5x 10/100/1000 Mbps
- wan (phy) : Qualcomm IPQ5018 (SoC)
- lan (switch) : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO): 8x/3x
- UART : through-hole on PCB, 4pins near the barcode
- assignment : 3.3V, TX, RX, NC, GND from the barcode side
- settings : 115200n8
- Power : 12 VDC, 1 A (Max. 11.5W)
Flash instruction using initramfs-factory.bin image:
1. Boot WRC-X3000GS2 normally with router mode
2. Access to the WebUI ("http://192.168.2.1/") on the device and open
the firmware update page ("ファームウェア更新")
3. Select the OpenWrt factory.bin image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing
Switching to the stock firmware:
1. Load the elecom.sh script
. /lib/upgrade/elecom.sh
2. Check the current index of rootfs
bootconfig_rw_index 0:bootconfig rootfs
3. Set the index to inverted value
bootconfig_rw_index 0:bootconfig rootfs <value>
bootconfig_rw_index 0:bootconfig1 rootfs <value>
example:
- step2 returned "0":
bootconfig_rw_index 0:bootconfig rootfs 1
bootconfig_rw_index 0:bootconfig1 rootfs 1
- step2 returned "1":
bootconfig_rw_index 0:bootconfig rootfs 0
bootconfig_rw_index 0:bootconfig1 rootfs 0
4. Reboot
Partition Layout (Stock FW):
0x000000000000-0x000000080000 : "0:SBL1"
0x000000080000-0x000000100000 : "0:MIBIB"
0x000000100000-0x000000140000 : "0:BOOTCONFIG"
0x000000140000-0x000000180000 : "0:BOOTCONFIG1"
0x000000180000-0x000000280000 : "0:QSEE"
0x000000280000-0x000000380000 : "0:QSEE_1"
0x000000380000-0x0000003c0000 : "0:DEVCFG"
0x0000003c0000-0x000000400000 : "0:DEVCFG_1"
0x000000400000-0x000000440000 : "0:CDT"
0x000000440000-0x000000480000 : "0:CDT_1"
0x000000480000-0x000000500000 : "0:APPSBLENV"
0x000000500000-0x000000640000 : "0:APPSBL"
0x000000640000-0x000000780000 : "0:APPSBL_1"
0x000000780000-0x000000880000 : "0:ART"
0x000000880000-0x000000900000 : "0:TRAINING"
0x000000900000-0x000003c40000 : "rootfs"
0x000003c40000-0x000003fc0000 : "Config"
0x000003fc0000-0x000007300000 : "rootfs_1"
0x000007300000-0x000007680000 : "Config_2"
0x000007680000-0x000007b80000 : "Reserved"
0x000007b80000-0x000007c00000 : "FWHEADER"
0x000007c00000-0x000007c80000 : "Factory"
Known Issues:
- All Wi-Fi related peripherals are disabled.
This device has only 256 MiB RAM and it's too few for ath11k. To
prevent OOM when using LuCI or other softwares, disable Wi-Fi related
peripherals in device tree at the moment.
- This device has a Macronix MX35UF1G24AD SPI-NAND chip registered as
oobsize=128 in Linux Kernel. But using BCH8 breaks I/O on the chip
with the following errors, so this support uses BCH4 instead.
root@OpenWrt:~# strings /dev/mtdblock10
[26427.133154] mtdblock: MTD device '0:appsblenv' is NAND, please consider using UBI block devices instead.
[26427.134125] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 2
[26427.142240] I/O error, dev mtdblock10, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 2
[26427.151427] I/O error, dev mtdblock10, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 2
[26427.160440] I/O error, dev mtdblock10, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[26427.169619] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[26427.178083] Buffer I/O error on dev mtdblock10, logical block 0, async page read
Notes:
- This device has dual-boot feature and it's managed by the index in the
0:bootconfig and 0:bootconfig1 partitions.
MAC Addresses:
LAN : 38:97:A4:xx:xx:60 (0:APPSBLENV, "eth1addr"/"ethaddr" (text))
WAN : 38:97:A4:xx:xx:63 (0:APPSBLENV, "eth0addr" (text))
2.4 GHz: 38:97:A4:xx:xx:61 (0:APPSBLENV, "wifi0" (text))
5 GHz : 38:97:A4:xx:xx:62 (0:APPSBLENV, "wifi1" (text))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18543
Signed-off-by: Robert Marko <robimarko@gmail.com>
Make the ECC strength in the qpic-snand driver configurable via device
tree to use the device-specific ECC strength value.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18543
Signed-off-by: Robert Marko <robimarko@gmail.com>
The TP-link Deco X80-5G is a AX WIFI router with a single 1G (LAN) and 1 2.5G (WAN) port with a built in Quectel 5G modem.
Specifications:
Architecture ARMv8-A (aarch64 Cortex A53, 4 cores)
Vendor Qualcomm
Bootloader U-Boot (2016)
System-On-Chip Qualcomm IPQ8074A (Networking Pro 1210 platform)
CPU/Speed 2.2GHZ
Flash-Chip ESMT F59D1G81MB-45TI 1G-bit NAND
Flash MB 128MB (1Gbit)
RAM-chip 2* ESMT M15T4G16256A-DEBG2G 2Gb DDR3L (32bit)
RAM MB 512MB (4Gbit)
WLan System-On-Chip (5g) Qualcomm QCN5054
WLan Front end modules (5g) 8* Qorvo QPF4588
WLAN (5G) A/N/AC/AX
WLAN Antenna (int) 8* (4 shared with 2.5G)
WLan System-On-Chip (2.4G) Qualcomm QCN5024
WLan Front end modules (2.4G) 4* Skyworks SKY85340-11
WLAN (2.4G) B/G/N/AX
WLAN Antenna (int) 4* (shared with 5g)
Eithernet-phy (1Gbit) Qualcomm (Atheros) AR8033-AL1A
Ethernet (1Gbit) 1*
Eithernet-phy (2.5Gbit) Qualcomm QCA8081
Ethernet (2.5Gbit) 1*
Switch Embedded in the SOC?
Serial 1.8v 8n1 (testpoints)
Modem System-On-Chip Qualcomm 5G RG50xQ (Snapdragon X55 platform)
5G modem capability 5000Mbps down 900Mbps up
5G modem bands N1/N3/N5/N7/N8/N20/N28/N38/N40/N41/N77/N78/N79
4G modem capability 4.5G LTE-Advanced Pro (Cat20 down 2Gbps) (Cat18 up 200Mbps)
4G modem FDD bands B1/B3/B5/B7/B8/B18/B19/B20/B26/B28
4G modem TDD bands B34/B38/B39/B40/B41/B42/B43
Modem antenna (int) 8* (5G/4G use)
Modem antenna (ext) 2* SMA connectors (5G/4G use)
SIM type 1* Nano SIM
Telephony 1* POTS RJ11
(see wiki for more info:)
https://openwrt.org/inbox/toh/tp-link/x80-5g_v1
Notes:
Installation Instructions:
Between antennas 7 and 8 on the PCB with the RGB harness there are three test pads labelled TP1 TP2 and TP3 connections are as follows:
|TP2|-- RX
|TP1|-- TX
|TP3|-- GND
RX requires an external pullup to operate somewhere around 5 K ohm but your luck may vary the Uart is 1.8v
Set a static IP and set up a tftpserver and terminal.
power the router and quickly type the magic string “tpl” and press enter to break into u-boot
in the shell set the environment variables to enable tftp booting
setenv ipaddr (routerIP)
setenv serverip (server IP)
load you initramfs:
tftpboot 0x44000000 (serverIP):openwrt-qualcommax-ipq807x-tplink_x80-5g-initramfs-uImage.itb
boot your initramfs
bootm
upload your factory image to /tmp
format and install the factory image:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-qualcommax-ipq807x-tplink_x80-5g-squashfs-factory.ubi
Note as this device swaps root partitions upon update your boot partition may be set as mtd13
Update script to mount factory tplink partition's for MAC recovery and device data.
Capture Labelmac from Factory_data partition.
Patch LAN from Labelmac.
Patch ART from Labelmac.
Set GPIO to make modem operational from boot.
GPIO fan tables work like the stock device with three fan maps high active idle with a top fan speed of 6800 RPM.
High temp 70 deg speeds 6-8
Active temp 50 deg speeds 2-5
low temp 25 degree speed 0-1
Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/16329
Signed-off-by: Robert Marko <robimarko@gmail.com>
Patch script used for mounting of factory data partitions to not assume devices names or use hardcoded identifiers.
Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/16329
Signed-off-by: Robert Marko <robimarko@gmail.com>
The IPQ5018 GE Phy driver registers two fixed rate clocks which are
passed on to the GCC which gatekeeps and passes them back to the phy.
Fix 'bad phandle' warning and tell consumer (GCC) how many cells to
expect when compiling.
Warning (clocks_property): /soc@0/clock-controller@1800000: Missing property '#clock-cells' in node /soc@0/mdio@88000/ethernet-phy@7 or bad phandle (referred from clocks[5])
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18548
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for GL.iNET (AX3000) B3000.
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Winbond W634GU6NQB-11 (512 MiB DDR3-933)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
* Wi-Fi: QCN6102 (2x2:2 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (3 Ports 10/100/1000 GBASE-T)
* Flash: Winbond W25N01GWZEIG (128 MiB)
* LEDs: 1x single-color blue LED (GPIO 24 Active High)
1x single-color white LED (GPIO 23 Active High)
* Buttons: 1x Reset (GPIO 27 Active Low)
Flash Instructions:
*** The .img files are now universal ! ***
Openwrt --> openwrt-qualcommax-ipq50xx-glinet_gl-b3000-squashfs-factory.img
GL.iNet OEM --> openwrt-b3000-4.5.18-0731-1722397535.img
Either file can be flashed, in any of the available upgrade options, in both Firmwares.
Pick a file .. pick a method .. and SEND IT !!
Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17903
Signed-off-by: Robert Marko <robimarko@gmail.com>
The reason phy fails to probe without explicitly overrided phy id is
that the reset timing fails to match. Fix it with proper `reset-delay-us` and
`reset-post-delay-us`.
While at it, change LED settings to match EAP610-Outdoor.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18450
Signed-off-by: Robert Marko <robimarko@gmail.com>
QCOM SPI NAND driver got merged upstream hence we can drop the special
patch from qualcommax and qualcommbe target and move them to the generic
backports directory to reduce patch maintenance.
While at it refresh any affected patch and target and also backport other
minor fixup for the SPI NAND driver merged upstream later.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Specifications:
* SoC: Qualcomm IPQ6018 (64-bit Quad-core Arm Cortex-A53 @ 1800MHz)
* Memory: 1 GiB
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCN9074 (4x4 5 GHz 802.11ax)
* Wi-Fi: IPQ6018 (4x4 2.4 GHz 802.11b/g/n/ax)
* Ethernet: RTL8211F (10/100/1GBASE-T)
* Flash: ESMT F59D1G81MB (128 MiB)
* LEDs: 1x Green Status (GPIO 37 Active High), 1x Yellow Status (GPIO 32
Active High) and an LED global control GPIO (GPIO 36 Active High, set
up by U-Boot)
* Buttons: 1x Reset (GPIO 9 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to the pads near T32 and T31.
2. Connect 3V3 TTL port to TX, RX, and GND, which are pad T31, T32 and
the pad near T31 respectively. Be sure not to connect VCC and
crossover TX and RX.
3. Copy RAM firmware image
openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-initramfs-uImage.itb
to TFTP server root, available at 192.168.0.1.
4. Connect PoE ethernet cable to the RJ45 port and hold Ctrl+B in the
serial console (115200 baud) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# setenv serverip 192.168.0.1
# setenv ipaddr 192.168.0.99
# tftpboot 0x44000000 openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq60xx-tplink_eap623od-hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18389
Signed-off-by: Robert Marko <robimarko@gmail.com>
Netgear WAX610 / WAX610Y is a 802.11ax AP claiming AX1800 support.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512MB
* Storage: Winbond W29N01HZBINF 128MB NAND
* Ethernet:
* 2.5GbE RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Power: Dual-color LED (Green / Orange), Single-color LED (Blue)
* Ethernet: Dual-color LED (Green / Orange)
* 2.4Ghz WiFi: 2x Single-color LED (Blue, Green)
* 5Ghz WiFi: 2x Single-color LED (Blue, Green)
* Buttons:
* 1x Reset
* UART: 4-pin populated header
* Pinout 1 - VCC, 2 - GND, 3 - TX, 4 - RX
Installation:
=============
Web UI method
-------------
Set up the device using the stock web UI in local management mode.
Download the ui-factory.tar image.
* Enter the Management tab
* Select Maintenance->Upgrade->Firmware Upgrade
* Ensure the "Upgrade Options" field has "Local" selected
* Click "Browse File" and select the image
* Click "Upgrade" (NOT "Upgrade Now") at the bottom of the page
The device will install the image but reboot back into the vendor
firmware. Return the to Firmware Upgrade page as above and select
"Boot up Backup Firmware". The device should reboot into OpenWRT.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot netgear_wax610-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the command line.
Signed-off-by: Erik Servili <serverror@serverror.com>
Link: https://github.com/openwrt/openwrt/pull/18377
Signed-off-by: Robert Marko <robimarko@gmail.com>
Codename: Divo
Hardware specification:
========
SoC: Qualcomm IPQ6018
RAM: 512MB (2x ESMT 256MB DDR3L M15T2G16128A–DEBG2R)
NAND Flash: 512MB (Macronix MX30UF4G18AC or SK Hynix H27S4G8F2EDA-BC)
Ethernet: 1x 10/100/1000/2500/5000Mbps (Marvell AQR114C-B0)
Ethernet: 4x 10/100/1000Mbps (Qualcomm QCA8075)
WiFi1: 6GHz ax 4x4@20/40/160 MHz (Qualcomm QCN9024 + Skyworks SKY85784-11) - channels 33-229
WiFi2: 5GHz ax 2x2@20/40/80 MHz (Qualcomm QCN5052 + Skyworks SKY85755-11) - channels 36-177
WiFi3: 2.4GHz ax 2x2@20/40 MHz (Qualcomm QCN5022 + Skyworks SKY8340-11)
IoT: Bluetooth 5 (CSR8811) - not implemented
LED: 1x RGB status + USB Blue (PWM)
USB: 1x USB 3.0
Button: WPS, Reset
Flash instructions (Without Serial):
========
Open Linksys Web UI - http://192.168.1.1/ca or http://linksysxxxxx.lan/ca depending on your setup.
xxxxx is the last 5 digits from the SN found on a sticker under the device.
Click on the Linksys Logo to by-pass smart app registration.
Login with your admin password. The default password can be found on the same sticker.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
Flash instructions (With Serial):
========
1. Installation using serial connection from OEM firmware (default login: root, password: admin):
- fw_printenv -n boot_part
In case of 2:
- flash_erase /dev/mtd13 0 0
- nandwrite -p /dev/mtd13 openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin
or in case of 1:
- flash_erase /dev/mtd15 0 0
- nandwrite -p /dev/mtd15 openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin
After first boot install firmware on second partition:
- mtd -r -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin kernel
or:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin alt_kernel
2. Installation from initramfs image using USB drive:
Put the initramfs image on the USB drive:
- dd bs=1M if=openwrt-qualcommax-ipq60xx-linksys_mr7500-initramfs-uImage.itb of=/dev/sda
Stop u-boot and run:
- usb start && usbboot $loadaddr 0 && bootm $loadaddr
Write firmware to the flash from initramfs:
- mtd -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin kernel
and:
- mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7500-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware:
- mtd -e kernel -n write FW_MR7500_1.1.12.211919_prod.img kernel
and:
- mtd -r -e alt_kernel -n write FW_MR7500_1.1.12.211919_prod.img alt_kernel
4. USB recovery:
Put the initramfs image on the USB:
- dd bs=1M if=openwrt-qualcommax-ipq60xx-linksys_mr7500-initramfs-uImage.itb of=/dev/sda
Set u-boot env:
- fw_setenv bootusb 'usb start && usbboot $loadaddr 0 && bootm $loadaddr'
- fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
AQR firmware:
========
0. Firmware extracting:
To extract the firmware, use unblob (unblob.org)
1. Firmware loading:
To properly load the firmware and initialize AQR PHY, we must use the u-boot aq_load_fw function.
To do this, you need to modify u-boot env:
With USB recovery:
- fw_setenv bootcmd 'aq_load_fw; run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
and without:
- fw_setenv bootcmd 'aq_load_fw; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
2. Firmware updating:
Newer firmware (AQR114C.cld) is available in the latest OEM firmware (https://downloads.linksys.com/support/assets/firmware/FW_MR7500_1.1.12.211919_prod.img).
Copy AQR114C.cld to /lib/firmware/marvell
Link: openwrt#17428
Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko@gmail.com>
ipq60xx series MR devices share some common attributes such as LED for
USB port.
Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko@gmail.com>
Linksys MR7500 features 4x QSGMII QCA8075 and 1x USXGMII (1/2.5/5 GbE)
Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko@gmail.com>
Create factory tar for EAP620 HD v1 and EAP660 HD v1 which is accepted by the stock UI.
Fix bug in ipq807x and ipq60xx makefiles so TPLINK_SUPPORT_STRING is handled properly.
Modify tplink-mkimage-2022 script and relevant makefiles to allow spaces in support strings (required for EAP620 HD v1 and EAP660 HD v1).
Installation steps are identical to EAP610-Outdoor:
Web UI method
-------------
Set up the device using the vendor's web UI. After that go to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
The connect to the machine via SSH:
ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>
Disable signature verification:
cliclientd stopcs
Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
* Go to System -> Firmware Update.
* Under "New Firmware File", click "Browse" and select the image
* Select "Update" and confirm by clicking "OK".
If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWRT.
Signed-off-by: Shymon Samsel <ssamsel@umass.edu>
Link: https://github.com/openwrt/openwrt/pull/18340
Signed-off-by: Robert Marko <robimarko@gmail.com>
Using the pending ascii-eq-delim-env4 driver is a better way to read mac addresses since no
extra config is required
The change is like eacc4d8c9b, except for using smem for devinfo
thanks to @musashino205 for pointing out the simplification that removes
the extra partition
Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18186
Signed-off-by: Robert Marko <robimarko@gmail.com>
Create factory tar for WAX620 and WAX630 which is accepted by the stock UI.
Must use 'Boot up Backup Firmware' button on stock upgrade page after install and reboot to swap partitions.
Signed-off-by: Erik Servili <serverror@serverror.com>
Link: https://github.com/openwrt/openwrt/pull/18334
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
SoC: Qualcomm IPQ6000
RAM: 512 MiB
Flash: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: 2.4GHz 802.11b/g/n/ax 2x2
WLAN2: 5GHz 802.11a/n/ac/ax 2x2
Button: Reset, Switch
USB: 1x 3.0
SD slot: 1 in GL-AXT1800
Install via stock firmware:
Upload factory.bin in stock firmware's upgrade page,
do not preserve settings.
Install via uboot web failsafe:
Push the reset button for 5 seconds, then use broswer
to access http://192.168.1.1, and upload factory.ubi.
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
Make cpufreq work on different IPQ60xx SoC.
Also rebase ipq6018-cp-cpu.dtsi for mp5496.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh device tree, remove the useless sdhc2 aliases.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is the minimal change for the upcoming patches.
Refresh the device tree of ipq807x at the same time.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
Because of the dt-bindings error, these patches have not
been merged yet, and the driver part is fine.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/14950
Signed-off-by: Robert Marko <robimarko@gmail.com>
The CONFIG_NET_SWITCHDEV option is needed by CONFIG_DSA and some other
options. It is boolean, we have to compile it into the kernel it self.
Activate it for all targets in the generic configuration, it is already
activated for most of them. This allows to install DSA drivers as a
module.
On the ramips/mt7620 target the kernel would grown by 4.5kB.
For some small targets which do not support a DSA switch by default the
option is deactivated.
Link: https://github.com/openwrt/openwrt/pull/17668
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds the missing properties to address the following warnings:
Warning (reg_format): /soc@0/spi@78b5000/flash@0/partitions/partition@x:reg: property has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1)"
Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: #18180
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for Linksys MR5500 (Hydra 6 Pro).
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Kingston D2516ECMDXGJD (512 MiB)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
QCN9024 (4x4:4 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (4 Ports 10/100/1000 GBASE-T)
* Flash: Gigadevice GD5F2GQ5REYIH (256 MiB)
* LEDs: 1x multi-color PWM LED
1x blue led for USB (GPIO 19 Active High)
* Buttons: 1x WPS (GPIO 27 Active Low)
1x Reset (GPIO 28 Acive Low)
5x ethernet port LEDs (amber for activity & green for link up)
* Peripherals: 1x USB2 (powered by GPIO 17 Active Low)
support for USB3 will be added in a separate PR
* FCC ID: 2AYRA-03734
Flash instructions:
1. On OEM firmware, login to the device (typically at http://192.168.1.1) and click 'CA'
in the bottom right corner -> Connectivity -> Manual Upgrade. Alternatively, browse to
http://<router IP>/fwupdate.html.
Upgrade firmware using openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin image.
Optionally install on second partition, after first boot check actual partition:
fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin kernel
and in case of 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
fw_printenv -n boot_part
In case of 2:
flash_erase /dev/mtd12 0 0
nandwrite -p /dev/mtd12 openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin
or in case of 1:
flash_erase /dev/mtd14 0 0
nandwrite -p /dev/mtd14 openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin
After first boot install firmware on second partition:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin kernel
or:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mr5500-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware.
Download firmware from OEM website:
MR5500: https://support.linksys.com/kb/article/207-en/
From serial or SSH:
fw_printenv boot_part
in case of 1:
mtd -r -e alt_kernel -n write FW_MR5500_1.1.2.209598_prod.img alt_kernel
else in case of 2:
mtd -r -e kernel -n write FW_MR5500_1.1.2.209598_prod.img kernel
4. Boot from USB
This allows you loading an OpenWrt image into RAM and is meant for recovery scenarios only.
Enable loading image from USB in u-boot. From serial or SSH:
fw_setenv bootusb 'usb start && usbboot &loadaddr && bootm $loadaddr'
fw_setenv bootcmd 'run bootusb; if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi'
Copy OpenWrt initramfs image to USB:
dd bs=1M if=openwrt-qualcommax-ipq50xx-linksys_mr5500-initramfs-uImage.itb of=/dev/sda
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17958
Signed-off-by: Robert Marko <robimarko@gmail.com>
Function remove_oem_ubi_volume was called before CI_UBIPART variable was defined.
Fixes: df1f6e1e18 (qualcommax: ipq807x: Remove OEM UBI volume before upgrade for Linksys MX devices)
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18090
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use Bluetooth UART and USB packages separetly.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15118
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
On the ipq50xx platform, the internal GE PHY at phy address 7 on mdio0
must be enabled as it's used to detect the virtual switch in qca-ssdk.
This is a platform wide condition and is therefore part of the dtsi.
However, by enabling the mdio0 bus in board-specific dts files, the ge_phy
is implicitly enabled. So, let's remove the superfluous status property
in the dts files for Linksys MX2000 and MX5500.
While at it, remove the redundant phy-mode property as it's set to sgmii
by default in the ipq5018-ess.dtsi file and fix indentation in the
firmware property of the q5v6_wcss node.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18029
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ascii-env driver enables reading name pair values from nand in ascii layout.
So, let's pick up and set the mac address accordingly.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18029
Signed-off-by: Robert Marko <robimarko@gmail.com>
The UBI volume name in OEM firmware for Linksys MX2000, MX5500, and
SPNMX56 is 'squashfs' instead of 'rootfs'. So let's update the volume
accordingly.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17968
Signed-off-by: Robert Marko <robimarko@gmail.com>
The SPNMX56 is an ISP-branded and distributed device similar to the MX5500
with the same Wifi chips (IPQ5018 for 2.4G and QCN9074 for 5G) but has an
additional QCA8081 PHY providing a 2.5gbps ethernet WAN port.
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Winbond W634GU6NB-11 (512 MiB DDR3-933)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
QCN9024 (4x4:4 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (3 Ports 10/100/1000 GBASE-T) and a
QCA8081 phy (up to 2.5 Gbps)
* Flash: Gigadevice GD5F2GM7RExxG (256 MiB)
* LEDs: 1x multi-color PWM LED
* Buttons: 1x WPS (GPIO 27 Active Low)
1x Reset (GPIO 28 Acive Low)
Flash instructions:
1. On OEM firmware, login to the device (typically at http://192.168.1.1)
and click 'CA' in the bottom right corner -> Connectivity ->
Manual Upgrade. Alternatively, browse to http://<router IP>/fwupdate.html
Upload openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin
Optionally flash 2nd partition, after first boot check actual partition:
fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin kernel
and in case of 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware
hit Enter once booted and enter credentials (login: root, password: admin)
fw_printenv -n boot_part
In case of 2:
flash_erase /dev/mtd12 0 0
nandwrite -p /dev/mtd12 openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin
or in case of 1:
flash_erase /dev/mtd14 0 0
nandwrite -p /dev/mtd14 openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin
After first boot install firmware on second partition:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin kernel
or:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_spnmx56-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware.
Download firmware from OEM website:
Firmware for this device cannot be searched for on the Linksys website.
Instead, we'd have to use serial to intercept the URL of the firmware
while it's trying to update. Firmware is ISP specific:
Toob (UK): http://download.linksys.com/updates/20241125t080737/FW_MX56TB_1.0.1.216218_prod.img
The intention is to collect URLs for different ISPs on a wiki page.
From serial or SSH:
fw_printenv boot_part
in case of 1:
mtd -r -e alt_kernel -n write FW_MX56TB_1.0.1.216218_prod.img alt_kernel
else in case of 2:
mtd -r -e kernel -n write FW_MX56TB_1.0.1.216218_prod.img kernel
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17968
Signed-off-by: Robert Marko <robimarko@gmail.com>
Aliyun AP8220 is an AP manufactured by Edgecore.
(Very similar to Edgecore EAP102)
Hardware specifications:
SoC: Qualcomm IPQ8071A
RAM: 1GB of DDR4 600MHz
Flash1: MX25U3235F 4MB
Flash2: MX30UF1G18AC 128MB
Ethernet: 2x 2.5G RJ45 port
USB: 2x USB-A 2.0 port
WiFi1: QCN5024 2.4GHz
WiFi2: QCN5054 5GHz
Power: DC 12V / PoE
Flash instructions:
1. Connect the router via serial port
2. Keep pressing @ until uboot is interrupted
3. Download the initramfs image, rename it to
initramfs.bin, host it with tftp server
4. Run these commands:
tftpboot initramfs.bin
bootm
5. After openwrt boots up, use scp or luci
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17970
Signed-off-by: Robert Marko <robimarko@gmail.com>
Cleanup 02_network script indentation.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17970
Signed-off-by: Robert Marko <robimarko@gmail.com>
Devices that rely on faking the NAND controler compatible for U-Boot
to patch the nodes should add it in their DTS directly, this does not
belong in the SoC DTSI.
Link: https://github.com/openwrt/openwrt/pull/17908
Signed-off-by: Robert Marko <robimarko@gmail.com>
Replace the existing SPI NAND controller patches with the latest v14 set
that is pending upstream, and include Ansuels patch that fixes it.
Bindings patch is removed as there is no point carrying it in OpenWrt.
Link: https://github.com/openwrt/openwrt/pull/17908
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add patch to fix Qcom SNAND driver and move the SNAND patches to
backports directory as they are shared between qualcommax and qualcommbe
target.
Fixes: #17897
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17900
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh the ipq50xx kernel config as it looks like it was created by hand
instead of kernel_menuconfig so we have stuff like DWC3 which is packaged
as a kmod in a generic way, QMI helpers are part of backports etc.
Link: https://github.com/openwrt/openwrt/pull/17890
Signed-off-by: Robert Marko <robimarko@gmail.com>
Newly introduced IPQ5018 specific symbols will stop compilation of
ipq807x and ipq60xx subtargets, so make sure to disable them in the
generic config.
Link: https://github.com/openwrt/openwrt/pull/17884
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for Linksys MX2000 (Atlas 6) and MX5500 (Atlas 6 Pro).
These devices are completely identical except for the secondary wifi
chip used for 5Ghz: QCN6102 is used on MX2000 while QCN9024 is used
on MX5500
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Winbond W634GU6NB-11 (512 MiB DDR3-933)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax)
* Wi-Fi: MX2000: QCN6102 (2x2:2 5 Ghz 802.11an/ac/ax)
MX5500: QCN9024 (4x4:4 5 Ghz 802.11an/ac/ax)
* Ethernet: IPQ5018 integrated virtual switch connected to an external
QCA8337 switch (4 Ports 10/100/1000 GBASE-T)
* Flash: Macronix MX35UF2GE4AD (256 MiB)
* LEDs: 1x multi-color PWM LED
* Buttons: 1x WPS (GPIO 27 Active Low)
1x Reset (GPIO 28 Acive Low)
Flash instructions (in case of MX2000, else replace with MX5500 images):
1. On OEM firmware, login to the device (typically at http://192.168.1.1) and click 'CA'
in the bottom right corner -> Connectivity -> Manual Upgrade. Alternatively, browse to
http://<router IP>/fwupdate.html.
Upgrade firmware using openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin image.
Optionally install on second partition, after first boot check actual partition:
fw_printenv -n boot_part
and install firmware on second partition using command in case of 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin kernel
and in case of 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin alt_kernel
2. Installation using serial connection from OEM firmware (default login: root, password: admin):
fw_printenv -n boot_part
In case of 2:
flash_erase /dev/mtd12 0 0
nandwrite -p /dev/mtd12 openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin
or in case of 1:
flash_erase /dev/mtd14 0 0
nandwrite -p /dev/mtd14 openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin
After first boot install firmware on second partition:
mtd -r -e kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin kernel
or:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq50xx-linksys_mx2000-squashfs-factory.bin alt_kernel
3. Back to the OEM firmware.
Download firmware from OEM website:
MX2000: https://support.linksys.com/kb/article/585-en/
MX5500: https://support.linksys.com/kb/article/587-en/
From serial or SSH:
fw_printenv boot_part
in case of 1:
mtd -r -e alt_kernel -n write FW_MX2000_1.1.7.210469_prod.img alt_kernel
else in case of 2:
mtd -r -e kernel -n write FW_MX2000_1.1.7.210469_prod.img kernel
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add QCN6122 platform support.
QCN6122 is a PCIe based solution that is attached to and enumerated
by the WPSS (Wireless Processor SubSystem) Q6 processor.
Though it is a PCIe device, since it is not attached to APSS processor
(Application Processor SubSystem), APSS will be unaware of such a decice
and hence it is registered to the APSS processor as a platform device(AHB).
Because of this hybrid nature, it is called as a hybrid bus device.
As such, QCN6122 is a hybrid bus type device and follows the same codepath
as for WCN6750.
This is a reversed engineered and heavily simplified version of below
downstream patch:
https://git.codelinaro.org/clo/qsdk/oss/system/feeds/wlan-open/-/ \
blob/NHSS.QSDK.12.4.5.r2/mac80211/patches/232-ath11k-qcn6122-support.patch
Co-developed-by: George Moussalem <george.moussalem@outlook.com>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Introduce support for the Qualcomm IPQ50xx SoC.
This series adds support for the following components:
- minimal boot support: GCC/pinctrl/watchdog/CPUFreq/SDI (upstreamed)
- USB2 (upstreamed)
- Thermal/Tsens
- PCIe gen2 1&2-lane PHY and controller
- PWM and PWM LED
- QPIC SPI NAND controller
- CMN PLL Block (provider of fixed rate clocks to GCC/ethernet/more.)
- Ethernet: IPQ5018 Internal GE PHY (1 gbps)
- Remoteproc MPD driver for IPQ5018 (2.4G) & QCN6122 (5/6G) Wifi
Co-developed-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use 'remove_oem_ubi_volume' function to remove OEM UBI volume before upgrade.
This allows to upgrade even if we have OEM firmware on the second partition.
Applies to Linksys MX4200/MX4300/MX5300/MX8500.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14720
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update u-boot env variables only when changes are made.
Applies to Linksys MX4200/MX4300/MX5300/MX8500.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14720
Signed-off-by: Robert Marko <robimarko@gmail.com>
Dual firmware devices like Linksys MX4200, MX4300, MX5300 and MX8500 use separate rootfs partition.
This option helps to keep all configuration during upgrade.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14720
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fixed an issue where both WAN LEDs light up before plugging in the
ethernet cable and no blinking regardless of WAN network activity.
Updated the LED configuration to reflect proper status:
Green indicates 2.5Gb connection speed.
Yellow indicates other connection speed and traffic activity.
This resolves inconsistent WAN LED behavior on Spectrum SAX1V1K routers.
Signed-off-by: Ivan Deng <hongba@rocketmail.com>
Link: https://github.com/openwrt/openwrt/pull/17623
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, 2.5G port LED-s on Dynalink are incorrectly configured and thus
they will light up all of the time.
So, lets fix this by:
1. Current green LED is actually yellow, change the color
2. Fix its polarity as its actually active-low
3. The yellow LED that was registered as being connected to LED_1 pin on
the PHY is not actually connected at all, so remove it.
4. The actual green LED is connected to LED_2 on the PHY so add it.
Fixes: 75ad5c2414 ("qualcommax: switch to qca8081 upstream PHY driver")
Fixes: #14502
Link: https://github.com/openwrt/openwrt/pull/17656
Signed-off-by: Robert Marko <robimarko@gmail.com>
TP-Link EAP610-Outdoor is a 802.11ax AP claiming AX1800 support. It is
wall or pole mountable, and rated for outdoor use. It can only be
powered via PoE.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512 MB
* Storage: ESMT PSR1GA30DT 128MB NAND
* Ethernet:
* Gigabit RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Multi-color System LED (Green/Amber)
* Buttons:
* 1x Reset
* UART: 4-pin unpopulated header
* 1.8 V level, Pinout 1 - TX, 2 - RX, 3 - GND, 4 - 1.8V
Installation:
=============
Web UI method
-------------
Set up the device using the vendor's web UI. After that go to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
The connect to the machine via SSH:
ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>
Disable signature verification:
cliclientd stopcs
Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
* Go to System -> Firmware Update.
* Under "New Firmware File", click "Browse" and select the image
* Select "Update" and confirm by clicking "OK".
If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWRT.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot tplink_eap610-outdoor-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the commandline.
The tplink2022 image format
============================
The vendor images of this device are packaged in a format that does
not match any previous tplink formats. In order for flashing to work
from the vendor's web UI, firmware updates need to be packaged in
this format. The `tplink-mkimage-2022.py` is provided for this
purpose.
This script can also analyze vendor images, and extract the required
"support" string. This string is checked by the vendor firmware, and
images with a missing or incorrect string are rejected.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14922
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit 7ce4ed4829.
Turns out that this requires more work, so revert to prevent making the
LED uncontrollable.
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Linksys MX4200v2 doesn't have the same LED controller as the MX4200v1 or MX4300. It comes with the STMicroelectronics LED1202 while the others come with the NXP PCA9633.
This LED controller has a driver under development which is currently being reviewed by the respective kernel maintainers. They are currently on v11.
Apart from the changes needed on the MX4200v2, this commit also amends the configuration of other devices affected by this change as the LED controller is no common to all of them as it was originally thought.
Signed-off-by: Manuel Fombuena <fombuena@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17451
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add kernel command line replacement hack to qualcommax. Now we can
find and replace arguments in the kernel command line by setting
bootargs-find-1, bootargs-replace-1, bootargs-exact-match-1
and bootargs-find-2, bootargs-replace-2, bootargs-exact-match-2
under the chosen node in the device tree.
This hack replaces the first occurence of bootargs-find-X with
bootargs-replace-X. When bootargs-exact-match-X is set to "y",
then the replacement happens only if the kernel command line is
identical to bootargs-find-X.
Signed-off-by: Qiyuan Zhang <zhang.github@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/16070
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently for Linksys MX4200v2 all u-boot ethXaddr variables share the same MAC address
and there is no need to check them one by one.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16070
Signed-off-by: Robert Marko <robimarko@gmail.com>
Define shared configuration for Linksys MX4x00 devices.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16070
Signed-off-by: Robert Marko <robimarko@gmail.com>
Create a generic Linksys MX4x00 dts file and extract the specific configuration
for MX4200v1/v2 to a new file.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16070
Signed-off-by: Robert Marko <robimarko@gmail.com>
The default value for the "root" parameter is "/dev/ubiblock0_0"
and there is no need to append it to bootargs.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16070
Signed-off-by: Robert Marko <robimarko@gmail.com>
These PHY LED-s are leftovers from a time when PHY LED offloading did not
work like the stock FW, so remove them as they are commented-out anyway.
Link: https://github.com/openwrt/openwrt/pull/17413
Signed-off-by: Robert Marko <robimarko@gmail.com>
The former is deprecated in favor of nvmem-layout. In preparation for
eventual removal from the kernel, do so here.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16097
Signed-off-by: Robert Marko <robimarko@gmail.com>
The former is deprecated in favor of nvmem-layout. In preparation for
eventual removal from the kernel, do so here.
Some of these are leftovers from nvmem-layout conversion.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16097
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
* SoC: Qualcomm IPQ8072A (64-bit Quad-core Arm Cortex-A53 @ 1.4 GHz)
* Memory: 2x ESMT M15T4G16256A-DEBG2G (1 GiB DDR3-1866 13-13-13)
* Serial Port: 3v3 TTL 115200n8
* Wi-Fi: QCA5054 (4x4 5 GHz 802.11ax)
* Wi-Fi: QCN5024 (2x2 2.4 GHz 802.11b/g/n/ax)
* Ethernet: AR8031 (10/100/1000BASE-T)
* Flash: Winbond W29N01HZSINF (128 MiB)
* LEDs: 1x Blue Status (GPIO 42 Active High)
* Buttons: 1x Reset (GPIO 50 Active Low)
Installation Instructions (Serial+TFTP):
1. Solder 4 pin header to JP1 and bridge pads of R58 and R62.
2. Connect 3V3 TTL port to TX, RX, and GND, which are positions 1, 2, and 3 respectively.
Be sure to crossover TX and RX.
3. Copy RAM firmware
openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb
to a TFTP server's root that is in the same subnet as your AP.
4. Power up the AP hold Ctrl+B in the serial console (115200n8) until autoboot is halted.
5. Run the following commands in the U-boot prompt:
# setenv serverip <TFTP server addr>
# setenv ipaddr <addr of AP>
# tftpboot 0x44000000 openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-initramfs-uImage.itb
# bootm
You may need to type Ctrl+C and Enter before running these commands
to clear invisible characters from the buffer.
6. Run the following command in a terminal to copy the sysupgrade image
to be installed (check IP address):
$ scp -O openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/
7. Activate the OpenWrt serial console and run the following commands:
# cd /tmp
# sysupgrade -n openwrt-qualcommax-ipq807x-tplink_eap620hd-v1-squashfs-sysupgrade.bin
8. The AP will reboot and OpenWrt will be successfully installed.
Known Issues:
* 5GHz radio instability (upstream current ath11k build bug maybe?)
Device support directly followed from EAP660HDv1 support
Links: #15832
Signed-off-by: Shymon Samsel <ssamsel@umass.edu>
Link: https://github.com/openwrt/openwrt/pull/17254
Signed-off-by: Robert Marko <robimarko@gmail.com>
The qusb_phy node looks for the following supply:
"vdd", "vdda-pll", "vdda-phy-dpdm"
And ssphy node looks for the following supply:
"vdda-phy", "vdda-pll"
So fix the usb regulator supply for RT-AX89X.
Fixes: 1306237 ("qualcommax: use PHY regulator for USB GPIO")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17290
Signed-off-by: Robert Marko <robimarko@gmail.com>
The PHY can handle turning off the GPIOs when turning off all USB ports.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17192
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use ath11k_patch_mac and ath11k_set_macflag functions
instead of fix_wifi_mac script.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/17230
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add NETGEAR_BOARD_ID and NETGEAR_HW_ID to DEVICE_VARS as multiple devices
set them in their recipes, so without them being added to DEVICE_VARS then
simply the value from last recipe that gets evaluated is used and images
are generated with the wrong ID-s.
Link: https://github.com/openwrt/openwrt/pull/17203
Signed-off-by: Robert Marko <robimarko@gmail.com>
Linksys MR7350 is a 802.11ax Dual-band router/AP.
Specifications:
* CPU: Qualcomm IPQ6000 Quad core Cortex-A53(A73) 1.5GHz
* RAM: 512MB of DDR3
* Storage: 256Mb NAND
* Ethernet: 5x1G RJ45 ports (QCA8075)
* WLAN:
* 2.4GHz: Qualcomm QCN5022 2x2 802.11b/g/n/ax 574 Mbps PHY rate
* 5GHz: Qualcomm QCN5052 2x2@80MHz or 802.11a/b/g/n/ac/ax 1201 Mbps PHY rate
* LED-s:
* RGB system led
* USB blue led
* Buttons: 1x Soft reset 1x WPS
* Power: 12V DC Jack
Installation instructions:
Open Linksys Web UI - http://192.168.1.1/ca or http://10.65.1.1/ca depending on your setup.
Login with your admin password. The default password can be found on a sticker under the device.
To enter into the support mode, click on the “CA” link and the bottom of the page.
Open the “Connectivity” menu and upload the squash-factory image with the “Choose file” button.
Click start. Ignore all the prompts and warnings by click “yes” in all the popups.
The Wifi radios are turned off by default. To configure the router, you will need to connect your computer to the LAN port of the device.
Then you would need to write openwrt to the other partition for it to work
- First Check booted partition:
fw_printenv -n boot_part
- Change the partition:
fw_setenv boot_part 1
or
fw_setenv boot_part 2
depending on the current partition
- Then install Openwrt to the other partition if booted in slot 1:
mtd -r -e alt_kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7350-squashfs-factory.bin alt_kernel
- If in slot 2:
mtd -r -e kernel -n write openwrt-qualcommax-ipq60xx-linksys_mr7350-squashfs-factory.bin kernel
Co-Authored-by: Chukun Pan <amadeus@jmu.edu.cn>
Co-Authored-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Vladyslav Andreichykov <vladdrako007@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14807
Signed-off-by: Robert Marko <robimarko@gmail.com>
Userspace regulator consumer is rather usefull so enable it for ipq60xx
as well and remove from ipq807x only kernel config.
Link: https://github.com/openwrt/openwrt/pull/14807
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
SoC: Qualcomm IPQ6000 1.5GHz
RAM: NTCC256M16ER-EK 512MiB
Flash: W29N01HZSINA 128MiB
ETH: QCA8075 (3x LAN, 1x WAN)
WLAN1: 2.4GHz 802.11b/g/n/ax 2x2
WLAN2: 5GHz 802.11a/n/ac/ax 2x2
Power: DC 12V 1.5A
Button: Reset, Wps
USB: 1x 2.0
Flash instructions:
1. Download the initramfs image, rename it to
initramfs.itb, host it with the tftp server.
2. Interrupt U-Boot and run these commands:
tftpboot initramfs.itb
bootm
3. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15940
Signed-off-by: Robert Marko <robimarko@gmail.com>
Its been a while since we added ipq60xx as source-only, it is now
quite usable so lets remove the source-only flag to start building
official images.
I also plan to merge additional popular boards rather soon.
Link: https://github.com/openwrt/openwrt/pull/17065
Signed-off-by: Robert Marko <robimarko@gmail.com>
These get dynamically set based on compiler version. Not relevant for
targets.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16770
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This symbol is no longer present.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16770
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All ipq807x devices that were using the legacy 'mmc_do_upgrade' eMMC
sysupgrade code were ported to the replacement 'emmc_do_upgrade' code.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
Alphabetically sort devices in platform.sh
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16505
Signed-off-by: Robert Marko <robimarko@gmail.com>
