Partially revert commit 332645a610 ("uboot-mediatek: sync with
mtk-openwrt/u-boot 20250711") by dropping unused PHY drivers which come
with large embedded firmware (and are hence inacceptable for upstream)
and restoring our previous version of the Airoha EN8811H driver which is
known to work and load firmware from the eMMC boot1 hardware partition
instead of embedding it in the driver.
In future we may switch to the upstream Airoha EN8811H driver which
allows loading the firmware either from a filesystem or overloading the
en8811h_read_fw() for board which may eg. store that firmware directly
inside a eMMC hardware partition or UBI volume, like the BPi-R3 mini
does.
See also:
https://patchwork.ozlabs.org/project/uboot/patch/20250615131243.30770-1-lucienzx159@gmail.com/
Fixes: 332645a610 ("uboot-mediatek: sync with mtk-openwrt/u-boot 20250711")
Reported-by: Adrian Bente
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Update mediatek arm-trusted-firmware to the latest version.
Remove upstream patch:
0004-mediatek-snfi-fix-return-code-when-reading.patch
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
The build error has been fixed by the upstream commit:
03e598263e38 ("tools: fix build without LIBCRYPTO support")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Most ramips target devices use the legacy uImage format. This
patch extends the imsz/imszb commands to support detecting the
image size of legacy uImage.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Add back the default LK image header to generate u-boot-mtk.bin. This
is the default behavior before u-boot v2022.01. If "u-boot-mtk.bin"
doesn't boot, please try "u-boot.bin" and report it.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Update to the latest version.
Suppressed patch:
100-04-env-add-support-for-generic-MTD-device.patch[1]
[1] 03fb08d4ae
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Add an OpenWrt-based U-Boot build for this device, allowing for more
flexibility and customization.
Expected behaviour
------------------
When plugging the device, keeping the reset button pressed will enter
TFTP recovery mode: the board will send requests for the initramfs file
(openwrt-mediatek-filogic-glinet_gl-mt2500-initramfs-kernel.bin) from
IP 192.168.1.1 to 192.168.1.10 TFTP server.
The bootloader will populate the environment with the unit serial number
as reported by the "sn" value in eMMC, the "sn_bak" value, the country
code and ddns. WAN and LAN MAC addresses are reported in the environment
as well.
Limitations
-----------
No web interface is available, and only the LAN port can be used for
system recovery.
Notes
-----
This port has been tested with the Maxlinear version only, and with a
board that does not exhibit eMMC communication problems. Even though eMMC
frequency has been lowered, some testing is probably needed and always
very welcome.
A -factory image has been introduced, and is only needed when using the
"Load Firmware via TFTP then write to eMMC." boot menu function.
The device has not been converted to use uImage.FIT including the rootfs
to keep compatibility with stock bootloader and firmware.
Installation
------------
From a Linux root shell:
0. Transfer the needed files to the board, placing them in /tmp.
1. Make sure your U-Boot environment is erased: all of my units came with
unpopulated environment, but I am not sure this is always the case.
Issue the command
cat /dev/zero >/dev/mmcblk0p2
(you will get a "no space left" error, which is reasonable and expected).
2. Unlock the eMMC boot area where BL2 is located:
echo 0 >/sys/block/mmcblk0boot0/force_ro
3. Write the new BL2 code:
cat openwrt-mediatek-filogic-glinet_gl-mt2500-emmc-preloader.bin >/dev/mmcblk0boot0
4. Write new BL31+U-Boot image:
cat openwrt-mediatek-filogic-glinet_gl-mt2500-emmc-bl31-uboot.fip >/dev/mmcblk0p4
5. Reboot.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
This commit updates the OpenWrt-based U-Boot for this device, allowing
to boot a FIT firmware image stored in an SD card.
The environment has been updated accordingly to allow for managing images
on the two different supported firmware boot media configurations
(NOR or SDMMC).
Erasing the U-Boot environment when upgrading is recommended, so that
the correct DTS overlay is applied.
New behaviour
-------------
The default environment "bootconf" variable is set to
config-1#mt7981b-gatonetworks-gdsp-gps
rendering the GPS module accessible.
You may set it to something like
config-1#mt7981b-gatonetworks-gdsp-sd
to be able to use the MMC controller.
To boot from a firmware image stored in an SD card, you may set the
bootmedia environment variable:
# fw_setenv bootmedia sd
and reboot.
Should the bootmedia variable be absent or it's content not recognized
as valid (e.g., does not contain "nor" or "sd"), NOR boot will be
attempted.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Host default environment doesn't provide/require gnutls headers needed
for building mkeficapsule tools, and as tegra target doesn't require EFI
capability, disable the build of mentioned tool.
Fixes: 92cd360aac ("uboot-tegra: bump version to 2025.04")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250713125126.215092-1-tmn505@terefe.re/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add new option to bootmenu which allows to boot the system from USB.
You can use dd to prepare USB with initramfs:
- dd bs=1M if=openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-factory.ubi of=/dev/sdX
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18949
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use common function ubootenv_add_mmc
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19269
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Dell/SonicWall APL27-0B1 (marketed as SonicPoint ACi) is a dual band
wireless access point. Very similar to already supported APL26-0AE,
which all antennas are external, while this variant has internal
antennas. End of life as of 2022-07-31.
Specification
SoC: QualcommAtheros QCA9550
RAM: 256 MB DDR2
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9890 oversized Mini PCIe card
Ethernet: 2x 10/100/1000 Mbps QCA8334
port labeled lan1 is PoE capable (802.3at)
USB: 1x 2.0
LEDs: LEDs: 6x which 5 are GPIO controlled and two of them are dual color
Buttons: 1x GPIO controlled
Serial: RJ-45 port, SonicWall pinout
baud: 115200, parity: none, flow control: none
Before flashing, be sure to have a copy of factory firmware, in case You
wish to revert to original firmware.
Installation
1. Prepare TFTP server with OpenWrt sysupgrade image and rename that
image to "ap135.bin".
2. Connect to one of LAN ports.
3. Connect to serial port.
4. Hold the reset button (small through hole on side of the unit),
power on the device and when prompted to stop autoboot, hit any key.
The held button can now be released.
5. Alter U-Boot environment with following commands:
setenv bootcmd bootm 0x9F110000
saveenv
6. Adjust "ipaddr" (access point, default is 192.168.1.1) and "serverip"
(TFTP server, default is 192.168.1.10) addresses in U-Boot
environment, then run following commands:
tftp 0x80060000 ap135.bin
erase 0x9F110000 +0x1EF0000
cp.b 0x80060000 0x9F110000 $filesize
7. After successful flashing, execute:
boot
8. The access point will boot to OpenWrt. Wait few minutes, until the
wrench LED will stop blinking, then it's ready for configuration.
Notes
By default no power is provided on USB port, so attached USB devices
won't enumerate. To change that enable regulator with:
echo "enabled" > /sys/devices/platform/output-usb-vbus/state
To disable power write "disabled" to the same file.
Ther regulator state will reset on reboot, consider running this command
on hotplug event or add it to /etc/rc.local. The hotplug event should
look like this:
if [ "${PRODUCT}" = "1d6b/2/606" ] && [ "${ACTION}" = "add" ]; then
echo "enabled" > /sys/devices/platform/output-usb-vbus/state
fi
Place it in /etc/hotplug.d/usb/10-usb-power.
Known issues
Initramfs image can't be bigger than specified kernel size, otherwise
bootloader will throw LZMA decompressing error. Switching to lzma-loader
should workaround that.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250529202033.28250-2-tmn505@terefe.re/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add uboot-envtools support for Gateworks venice boards based on i.MX8M
SoC's (imx_cortexa53) which boot from and store their U-Boot env on
eMMC boot0 hardware partition.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19347
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Force update_cache_variantsvariants to use reset for Foresee NAND with bad blocks.
Tested on Xiaomi AX3000T + F35SQA001G with bad blocks and without bad blocks
Signed-off-by: Dim Fish <dimfish@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17963
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The same function is used twice, so let's make it common.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18818
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Functions ubootenv_add_mtd, ubootenv_add_sys_mtd and ubootenv_add_mmc
can be shared so make them common.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18818
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently, uboot-envtools is being built for a (shared) instruction
set (phase2 in buildbots) instead of target-specific (phase1 in builbots).
So the package does not contain the uci-defaults file specific for each
target_subtarget. (Only the fortunate target with coincidentally the same
instruction set and target as the SDK chosen by the buildbot will have the
uci-defaults file.)
This commit sets the nonshared flag correctly in the Makefile so that
uboot-envtools is built for the target-specific (phase 1).
This is done by using the PKGFLAGS variable which is intended for
per-binary flags (instead of PKG_FLAGS which has a global scope), as
stated in some old commits 349e7b635e[1], 2d7eaf2e15[2], 064e7c8f00[3] and
2cb75cd8b9[4].
While at here, use PKG_URL, instead of URL, which is intended for global
scope. As stated in commit e32edf712b[5].
[1] 349e7b635e
[2] 2d7eaf2e15
[3] 064e7c8f00
[4] 2cb75cd8b9
[5] e32edf712bFixes: #19040
Fixes: 46e376c ("uboot-tools: migrate uboot-envtools to uboot-tools")
Signed-off-by: Mario Andrés Pérez <mapb_@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19180
Signed-off-by: Robert Marko <robimarko@gmail.com>
The IgniteNet SunSpot AC Wave2 uses the standard smem-assigned partition
for its bootloader environment.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The qcomsmem MTD partition parser converts all partition names to
lower case while the vendor solution uses upper case names, which
often made their way into OpenWrt as labels in 'fixed-partitions'
(probably due to contributors and reviewers being unaware of the
qcomsmem parsers).
Use case-insensitive matching of the 'APPSBLENV' name to make
ubootenv_mtdinfo() work in both cases.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for Check Point V-81 to add/edit bootcmd variables for
booting OpenWrt.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16904
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for Check Point V-80 to add/edit bootcmd variables for
booting OpenWrt.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16904
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This file is a leftover of cns3xxx target which has been dropped
in commit a9790dff53 ("cns3xxx: drop target").
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19191
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for Xiaomi AX6000.
Speficiations:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Etrontech EM6HE16EWAKG 512 MiB DDR3L-933
* Serial Port: 1v8 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax - up to 574 Mbps)
QCN9024 (4x4 5 Ghz 802.11an/ac/ax - up to 4804 Mbps)
QCA9887 (1x1 5 Ghz 802.11ac/n - up to 433 Mbps)
* Ethernet: IPQ5018 integrated virtual switch connected to:
- external QCA8337 switch (3 LAN Ports 10/100/1000)
- QCA8081 Phy WAN port (10/100/1000/2500)
* Flash: Either of:
- Gigadevice GD5F1GQ4RE9IGD (128 MiB)
- ESMT F50D1G41LB (128 MiB)
* LEDs: 1x WLAN Link (GPIO 23 Active High)
1x System Blue (GPIO 24 Active High)
1x System Yellow (GPIO 25 Active High)
1x WAN Link Blue (GPIO 26 Active High)
1x WAN Link Yellow (GPIO 27 Active High)
1x Green - Unused(GPIO 28 Active High)
3x LAN Phy Green
1x WAN Phy Green
* Buttons: 1x Reset (GPIO 38 Active Low)
Known issue:
- QCA9887 doesn't come up (possibly due to 1-lane PCIe phy not coming up or missing method to drive power),
hence the host PCIe controller is disabled in the DTS.
Flash instructions:
Download XMIR Patcher: https://github.com/openwrt-xiaomi/xmir-patcher
First flash a ubinized OpenWrt initramfs that will serve as the intermediate step, since
OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for
packages, through either of the below two methods:
Installation via XMIR Patcher:
1. Load the initramfs image: openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi
Installation via ubiformat method, through SSH:
1. If needed, enable SSH using XMIR Patcher.
2. Copy the file openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi to the /tmp directory
3. Open an SSH shell to the router
4. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
5. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd18 and mtd19 are the correct indexes from above!
6. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
7. Reboot the device by:
reboot
Continue in order to pernamently flash OpenWrt:
1. Upload the sysupgrade image to /tmp/ using SCP:
scp -O <path to image> root@192.168.1.1:/tmp/
2. Open an SSH shell to 192.168.1.1 from a PC within the same subnet
3. Use sysupgrade to flash the sysupgrade image:
sysupgrade -n -v /tmp/openwrt-qualcommax-ipq50xx-xiaomi_ax6000-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19004
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for I-O DATA WN-DAX3000GR to update bootdelay variable while
sysupgrade.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19053
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add an additional bootmenu option and commands to overwrite the GPT
table with the custom one for upstream U-Boot.
This is needed as the pre-installed GPT table differ and updating the
GPT table is a requirement to install the upstream U-Boot (or the old
U-Boot will be loaded)
To make the migration to new U-Boot bootloader an user can now load the
system with mtk_uartboot and select "Load GPT Table ..." in conjunction
with other update command.
Link: https://github.com/openwrt/openwrt/pull/18874
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace bootmenu shortmenu mediatek patch with a better version proposed
upstream that implement a more clean implementation.
Also the mediatek patch seems to be bugged and with lots of bootmenu
elements it's gets very bugged and unusable.
Refresh any affected patch.
Upstream-Status: Submitted [https://lore.kernel.org/u-boot/20250525134407.3760-1-ansuelsmth@gmail.com/]
Link: https://github.com/openwrt/openwrt/pull/18919
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This allows us to use the full size of nand, which increases ubi size
from 64M to 122.25M.
If you are at factory firmware, please refer commit 63b8d98dd0 ("mediatek: add support for Cudy TR3000 v1")
to boot into OpenWrt initramfs (stock layout).
Flash instructions:
1. Login into the device and backup everything, especially 'Factory' part.
1. Unlock mtd partitions:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
3. Write new BL2 and FIP
mtd write openwrt-mediatek-filogic-cudy_tr3000-v1-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cudy_tr3000-v1-ubootmod-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Tested-by: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
SOC: MediaTek MT7981b
RAM: 256MB DDR3
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7981b DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Interface MAC Algorithm
LAN 8C:AE:DB:2C:xx:xx label
WAN 8C:AE:DB:2C:xx:xx label +1
WLAN 2.4G 8C:AE:DB:2C:xx:xx label +2
WLAN 5G 8C:AE:DB:2C:xx:xx label +3
Installation
-------------------Install openwrt image-------------------------------:
Set a static ip on the ethernet interface of your PC. (ip address:
192.168.1.254, subnet mask:255.255.255.0) .
Download the OpenWrt uboot image
(openwrt-mediatek-filogic-snr_cpe-ax2-bl31-uboot.fip).
SSH/SCP opened by default on the stock firmware (3.0.1).
Username: Admin, default password: Admin. Check it on the bottom of
the router.
Copy uboot image using SCP (WinSCP) to /tmp dir on SNR-CPE-AX2.
Download recovery file.
openwrt-mediatek-filogic-snr_snr-cpe-ax2-initramfs-recovery.itb.
Copy the recovery image to a TFTP server reachable at 192.168.1.254/24.
Open ssh shell to the SNR-CPE-AX2.
Run commands:
mtd write \
/tmp/openwrt-mediatek-filogic-snr_snr-cpe-ax2-bl31-uboot.fip FIP
reboot
Wait until recovery boot.
Open web 192.168.1.1 and do sysupgrade by
openwrt-mediatek-filogic-snr_cpe-ax2-squashfs-sysupgrade.itb
Signed-off-by: Nikolay March <palladin82@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/18700
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
A lot of warnings were treated as errors after the default compiler
switched to GCC14. It's hard to fix them one by one, and this u-boot
is not maintained by upstream, so let's just silence these warnings.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18833
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This U-Boot version is used to generate a 'reference'
U-Boot binary for QEMU's 'virt' machine on both
armv7 and armv8.
It has not been updated since EFI support was merged
into the then-armvirt target, so we should bring it up
to the latest version.
The 'mkeficapsule' tool is disabled due to a host-side
dependency on GnuTLS.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Link: https://github.com/openwrt/openwrt/pull/18862
Signed-off-by: Robert Marko <robimarko@gmail.com>
TP-Link EAP625-Outdoor HD is a 802.11ax AP claiming AX1800 support.
It is wall or pole mountable, and rated for outdoor use. It can only
be powered via PoE.
Hardware-wise, it is very similar to the older EAP610-Outdoor model.
Software-wise, I couldn't find a difference other than the board
data files, and device name. For this reason, the majority of the
devicetree from the EAP610-Outdoor is reused.
This device currently comes in a "v1", and "v1.6" version. The
"support-list" of the vendor firmware does not have a distinction
between these versions. This commit was tested on a 'V1.6" device.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512 MB
* Storage: 128MB NAND
* Ethernet:
* Gigabit RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Multi-color System LED (Green/Amber)
* Buttons:
* 1x Reset
* UART: 4-pin unpopulated header
* 1.8 V level, Pinout 1 - TX, 2 - RX, 3 - GND, 4 - 1.8V
Installation:
=============
Web UI method
-------------
Set up the device using the vendor's web UI. After that go to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
The connect to the machine via SSH:
ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>
Disable signature verification:
cliclientd stopcs
Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
* Go to System -> Firmware Update.
* Under "New Firmware File", click "Browse" and select the image
* Select "Update" and confirm by clicking "OK".
If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWRT.
NOTE: If ssh continues to complain that "no matching host key type
found. Their offer: ssh-rsa,ssh-dss" it likely means that yor distro
has completely disabled deprecated siphers in ssh. In that case, run
the ssh command from a docker container of an older distro.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot tplink_eap625-outdoor-hd-v1-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the commandline.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18584
Signed-off-by: Robert Marko <robimarko@gmail.com>
This fixes the following compile problem:
```
arv7506pw11.c: In function 'show_boot_progress':
arv7506pw11.c:59:24: error: 'return' with a value, in function returning void [-Wreturn-mismatch]
59 | return 0;
| ^
arv7506pw11.c:56:6: note: declared here
56 | void show_boot_progress(int arg)
| ^~~~~~~~~~~~~~~~~~
arv7506pw11.c:71:16: error: 'return' with a value, in function returning void [-Wreturn-mismatch]
71 | return 0;
| ^
arv7506pw11.c:56:6: note: declared here
56 | void show_boot_progress(int arg)
| ^~~~~~~~~~~~~~~~~~
```
Link: https://github.com/openwrt/openwrt/pull/18688
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
A patch was added upstream to temporary enable RTC clock configuration only
for STM32MP15 boards. Use this patch instead of reverting commit 03a581e2.
Now for STM32MP135 boards RTC clock configuration is handled by optee-os.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18628
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
