NPCM7xx/NPCM8xx default is boot from flash.
removed set clock feature due to reliability and security.
the clock will set by bootblock or tip.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The .supports_op() callback function returns true by default after
performing driver-specific checks. Therefore the driver cannot apply
the buswidth in devicetree.
Call spi_mem_default_supports_op() helper to handle the buswidth
in devicetree.
Fixes: 358f803ae2 ("spi: Add Socionext F_OSPI SPI flash controller driver")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
in spi_mem_dtr_supports_op we have a check for allowing only even number
of bytes to be r/w. Odd bytes writing can be a concern while writing
data to a flash for example because 8 DTR mode doesn't support it.
However, reading ODD Bytes even though may not be physically possible
we can still allow for it because it will not have serious implications
on any critical registers being overwritten since they are just reads.
Cc: Vaishnav Achath <vaishnav.a@ti.com>
Cc: Pratyush Yadav <pratyush@kernel.org>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Nikhil M Jain <n-jain1@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This should have been op->data.buswidth instead as we check for octal
bus width for the data related ops
Also add explanation for why there is checks for 8D even data bytes
Cc: Pratyush Yadav <pratyush@kernel.org>
Reviewed-by: Pratyush Yadav <ptyadav@amazon.de>
Tested-by: Nikhil M Jain <n-jain1@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Currently, in stm32_qspi_claim_bus(), QSPI_CR and QSPI_DCR registers
are saved in stm32_ospi_flash struct on first flash memory initialization
and restored on each flash accesses.
As the logic of spi-uclass.c changed since 'commit 741280e9ac
("spi: spi-uclass: Fix spi_claim_bus() speed/mode setup logic")'
set_speed() and set_mode() callbacks are called systematically when bus
speed or bus mode need to be updated, QSPI_CR and QSPI_DCR registers are
set accordingly.
So stm32_qspi_claim_bus() can be updated by removing QSPI_CR and QSPI_DCR
save/restore code and struct stm32_ospi_flash can be removed as well.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Use CONFIG_RCAR_64 to make the driver available on both
R-Car Gen3 and R-Car Gen4.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Freescale ESPI driver (CONFIG_FSL_ESPI) relies to the MPC85xx platform
(PowerPC) through arch/powerpc/include/asm/immap_85xx.h. The driver can't
compile on another architecture/platform.
Signed-off-by: Corentin Guillevic <corentin.guillevic@smile.fr>
It was incorrectly using an old priv->regs pointer, which was
initialized to zero. SPI resets won't happen on first call.
Signed-off-by: Jiajie Chen <c@jia.je>
Link: https://lore.kernel.org/r/20230227150938.211820-1-c@jia.je
Signed-off-by: Michal Simek <michal.simek@amd.com>
Original t20 slink could work with commands only
fully divisible by 8. This patch removes such
restriction, so commands of any bitlength now
can be passed and processed.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF600T T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Tested-by: Thierry Reding <treding@nvidia.com> # T30 and T124
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Tom <twarren@nvidia.com>
- A fix for a long standing bug that has been exposed by commit
50128aeb0f ("cyclic: get rid of cyclic_init()") preventing 8xx boards
from booting since u-boot 2023.01
- A GPIO driver for powerpc 8xx chip
- Fixup for powerpc 8xx SPI driver
- A new powerpc 8xx board
- The two devices having that board.
This patch fixes the mpc8xx SPI driver:
- A stub callbacks for mode and speed,
- Use chip selects defined as GPIOs,
- Write proper value to disable relocation, other it fails on mpc885,
- Don't modify ports setup, ports can be different from one board to
another and are already set by board_early_init_r().
This patch was originally written by Charles Frey who's
email address is not valid anymore as he left the company.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Reviewed-by: FRANJOU Stephane <stephane.franjou@csgroup.eu>
This converts 1 usage of this option to the non-SPL form, since there is
no SPL_ARCH_VERSAL defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 2 usages of this option to the non-SPL form, since there is
no SPL_ZYNQMP_FIRMWARE defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix the issue where some flash chips like cypress S25HS256T return the
value of the same register over and over in DAC mode.
For example in the TI K3-AM62x Processors refer [0] Technical Reference
Manual there is a layer of digital logic in front of the QSPI/OSPI
Drive when used in DAC mode. This is part of the Flash Subsystem (FSS)
which provides access to external Flash devices.
The FSS0_0_SYSCONFIG Register (Offset = 4h) has a BIT Field for
OSPI_32B_DISABLE_MODE which has a Reset value = 0. This means, OSPI 32bit
mode enabled by default.
Thus, by default controller operates in 32 bit mode causing it to always
align all data to 4 bytes from a 4byte aligned address. In some flash
chips like cypress for example if we try to read some regs in DAC mode
then it keeps sending the value of the first register that was requested
and inorder to read the next reg, we have to stop and re-initiate a new
transaction.
This causes wrong register values to be read than what is desired when
registers are read in DAC mode. Hence if the data.nbytes is very less
then prefer STIG mode for such small reads.
[0] https://www.ti.com/lit/ug/spruiv7a/spruiv7a.pdf
Tested-by: Vaishnav Achath <vaishnav.a@ti.com>
Signed-off-by: Dhruva Gole <d-gole@ti.com>
[jagan: add tab space for comments]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Setup the Addr bit field while issuing register reads in STIG mode. This
is needed for example flashes like cypress define in their transaction
table that to read any register there is 1 cmd byte and a few more address
bytes trailing the cmd byte. Absence of addr bytes will obviously fail
to read correct data from flash register that maybe requested by flash
driver because the controller doesn't even specify which address of the
flash register the read is being requested from.
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Reviewed-by: Pratyush Yadav <pratyush@kernel.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Introduce Socionext F_OSPI controller driver. This controller is used to
communicate with slave devices such as SPI flash memories. It supports
4 slave devices and up to 8-bit wide bus, but supports master mode only.
This driver uses spi-mem framework for SPI flash memory access, and
can only operate indirect access mode and single data rate mode.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Use log_warning() instead of printf() to print out driver information
Signed-off-by: Pengfei Fan <fanpengfei1@eswincomputing.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Fix some typos in spi drivers
Signed-off-by: Pengfei Fan <fanpengfei1@eswincomputing.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This value is never changed by boards, so just rename it to
SPI_IDLE_VAL to fit with the rest of the code.
Signed-off-by: Tom Rini <trini@konsulko.com>
Stop using CONFIG_SANDBOX_ARCH and use CONFIG_SANDBOX instead. For the
SPI related defines, set them directly in Kconfig. This now empties
arch/sandbox/include/asm/config.h.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
cadence_qspi_apb_enable_linear_mode() has a weak function defined, so no
need to gaurd this under if (CONFIG_IS_ENABLED(ARCH_VERSAL)).
In cadence_qspi_apb_write_execute(), enable linear mode is called twice by
mistake, remove extra one.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20221129114134.18909-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
When we pass the 64-bit address to read/write, only lower 32-bit
address is getting updated. Program the upper 32-bit address in the
DMA destination memory address MSBs register, which can handle upto
44-bit destination address.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20221125104413.26140-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The driver was using an incorrect value for GQSPI_LPBK_DLY_ADJ_DLY_1
tapdelay for Versal for frequencies above 100MHz. Change it from 2 to 1
based on the recommended value in IP spec.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20221123090451.11409-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
When cadence_qspi_versal_flash_reset() function is called in mini
u-boot where there is no firmware support, it is missing defines for
macro's BOOT_MODE_POR_0 & BOOT_MODE_POR_1. Remove them and replace with
already define macro's which have same values as these.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20221116141155.14788-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
These files reference SZ_ macros without including <linux/sizes.h>,
correct this.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As CONFIG_ARCH_BCM6858 is replaced with CONFIG_BCM6858, update the
driver Kconfig to use the new config symbol.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
As CONFIG_ARCH_BCM68360 is replaced with CONFIG_BCM6856, update the
driver Kconfig to use the new config symbol.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
As CONFIG_ARCH_BCM63158 is replaced with CONFIG_BCM63158, update the
Kconfig to use the new config symbol.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Add Nuvoton NPCM BMC Peripheral SPI controller driver.
NPCM750 include two general-purpose SPI interface.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This function is already defined in spi.h but no implementation of it
currently exists in the tree. The implementation is based on the static
function spi_set_speed_mode(). The function prototype is modified so
that an success or error condition can be returned to the caller.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Fix the following sparse and compile time warning triggered with W=1:
drivers/spi/zynqmp_gqspi.c:286:6:
warning: no previous prototype for 'zynqmp_qspi_set_tapdelay'
[-Wmissing-prototypes]
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20221004053730.25602-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
xilinx:
- Add support for new Versal NET SOC
zynqmp:
- Use mdio bus for ethernet phy description
- Wire ethernet phy reset via i2c-gpio
versal:
- Config cleanup
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYzGwogAKCRDKSWXLKUoM
Ial4AJ9+4WHn0MV2X7gK1fyh4lUW7ggPhQCggsYlSoACgMgdji17SAPhCv/W3IA=
=BmA9
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.01-rc1-v2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2023.01-rc1 (round 2)
xilinx:
- Add support for new Versal NET SOC
zynqmp:
- Use mdio bus for ethernet phy description
- Wire ethernet phy reset via i2c-gpio
versal:
- Config cleanup
This patch adds support for spi-mem controller found on newer MediaTek SoCs
This controller supports Single/Dual/Quad SPI mode.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Globally replace all occurances of WATCHDOG_RESET() with schedule(),
which handles the HW_WATCHDOG functionality and the cyclic
infrastructure.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
Driver can configure the SPI clock frequnecy to the
target value of "spi-max-frequency" property in
the device tree. The frequency is divided from HCLK,
200MHz. Usually, the ASPEED SPI clock frequency range
is between 12.5MHz and 100MHz. On AST2600, the lowest
SPI clock frequency can be about 780kHz.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
If "decoded-ranges" is defined in the device tree, the
driver will apply the decoded address ranges from this
property to the controller during probe stage.
This patch refers to the following OpenBMC u-boot patch.
https://patchwork.ozlabs.org/project/openbmc/list/?series=306969
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
There are some known HW problems about decoded
range register configurations on existing AST2500 and
AST2600 platforms. Additional callback function,
adjust_decoded_sz, is added to solve these problems
on each platform. Besides, aspeed_spi_trim_decoded_size
function is added to modify overall decoded address
size for fitting the maximum AHB decoded size.
Signed-off-by: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
