These cpu erratums are used by other SoCs, just remove them.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/19380
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move the following kernel symbol configs to generic:
COMPRESSED_INSTALL and IMX_SCMI related configs
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/19380
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This will allow more flexibility in using PHY drivers as kmods.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18435
Signed-off-by: Robert Marko <robimarko@gmail.com>
After update to v6.12 some PCS driver fixes were dropped and additional
are needed due to updated driver.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18435
Signed-off-by: Robert Marko <robimarko@gmail.com>
The original PCS driver did not use the .pcs_validate() in
phylink_pcs_ops. The patches for 1000/2500base-x and 10g modes were
taken from this old driver, and thus did not bother with
.pcs_validate(). Thus, even though these modes are supported, phylink
would not enable them.
To fix these, list these modes in .pcs_validate(). Also list them in
ipq_pcs_clk_rate_get(). While the latter does not appear to change
behavior, it does change the clock rates listed under
/sys/kernel/debug/clk
Co-developed-by: Mantas Pucka <mantas@8devices.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18435
Signed-off-by: Robert Marko <robimarko@gmail.com>
0102-arm64-dts-qcom-ipq9574-Fix-USB-vdd-info.patch was merged in 6.12.34
Other patches automatically refreshed.
Fixes: cb1b656027 ("kernel: bump 6.12 to 6.12.34")
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/19232
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Qualcomm TSENS driver only exposes sensors to as a thermal
zone without registering hwmon, making these temperature sensors
unreadable by lm-sensors. This commit enables CONFIG_THERMAL and
CONFIG_THERMAL_HWMON for qualcommbe target to access the sensors
from hwmon.
Suggested-by: Yao Zi <ziyao@disroot.org>
Signed-off-by: Zheng Zhang <everything411@qq.com>
Link: https://github.com/openwrt/openwrt/pull/19137
Signed-off-by: Robert Marko <robimarko@gmail.com>
As qualcommbe is now supported by the v6.12 kernel, there is no point
in v6.6 as well. Drop v6.6 support.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18982
Signed-off-by: Robert Marko <robimarko@gmail.com>
The qualcommbe target was introduced after openwrt-24.10. The v6.12
kernel is now available, and is likely to be used by the next openwrt
release.While the v6.6 kernel served as an interim development vehicle,
it is no longer useful for the qualcommbe target
The v6.12 patches contain more recent submissions of pending ipq95xx
drivers. I expect that it will be much easier to update v6.12 patches
with new submissions. For ease of maintenance, it makes sense to use
a single kernel for qualcommbe.
For these reasons, enable v6.12 by default.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18982
Signed-off-by: Robert Marko <robimarko@gmail.com>
The PCS driver in the 6.12 patchset is the v5 submission (see link
below). It solves a number of issues and crashes with teh pcs driver
from the 6.6 patchset. However, this new driver is missing support for
"10gbase-r", "10g-qxgmii", and 1000/2500base-x modes.
Port these modes to the 6.12 patchset. "2500base-x" in particular seems
to be needed to establish a 2.5G link on phy-mode="usxgmii";
Link: https://lore.kernel.org/lkml/20250207-ipq_pcs_6-14_rc1-v5-0-be2ebec32921@quicinc.com/
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that patches for v6.12 are available, add the config, and enable
6.12 as a testing kernel.
Compared to v6.6 the patches to add "10gbase-r", "2500base-x",
"1000base-x", and "10g-qxgmii" modes have not been ported yet. They do
not apply cleanly to the new PCS driver. As the currently supported
hardware does not use those modes, it is not possible to test them at
this time.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Copy the v6.6 config to v6.6. It will be updated in a subsequent
commit in order to show the changes.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Port reset and clock fixes from target/linux/qualcommbe/patches-6.6.
Modifications of v6.6 patches are noted in each commit body.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that ethernet is supported on IPQ9574, add the port nodes and
other requirements to enable ethernet on RDP433.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add the second part of the PPE driver. This includes the EDMA and
network device support. This part does not appear to have been
officially submitted for upstream review. The series is taken from
target/linux/qualcommbe/patches-6.6, and had to be heavily modified
in order to compile of v6.12. Changes to patches are noted in the
respective patch body.
Also add the PPE and EDMA nodes in this series.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add the v5 of the PCS patch. This is the latest submission as of this
writing. THe last four patches are not part of the submission. They
make the series work with v6.12 kernel, resolve a circular dependency
with the clocks, and add the DTS node. Include them as bundle.
Link: https://lore.kernel.org/lkml/20250207-ipq_pcs_6-14_rc1-v5-0-be2ebec32921@quicinc.com/
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
This driver is cherry-picked from target/linux/qualcommbe/patches-6.6.
While Qualcomm did submit past patches for QCA8084, the code has since
ben split from at803x. The existing OpenWRT version of the patch is
the cleanest version I could find. Add it here.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
These devicetree updates can work with the existing upstreamcode. They
do not require code changes. Add them before any code change.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add dts fixes from linux-next. Two patches from the NSSCC series are
still in -next did not yet land in mainline, as well as misc other DTS
changes. Add them here.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add relevant patches from upstream, up to v5.16-rc6. The gaps in the
patch numbersing are either patches that were picked into the stable
kernel (6.12.y), or that are already backported in
target/linux/generic. The gaps makes it easy for me to pick these
patches from my working kernel git branch.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18796
Signed-off-by: Robert Marko <robimarko@gmail.com>
IPQ9554 does not have uniphy1. The "gcc_uniphy1_sys_clk" cannot be
enabled. This causes the ipq-uniphy driver to crash on .probe().
Add a patch to resolve the crash.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18779
Signed-off-by: Robert Marko <robimarko@gmail.com>
USXGMII link-up may fail due to too short delay after PLL reset.
Increase the delay to fix this.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fixes to PCS driver to support 2.5G PHY
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Missing bus clock prevent access to NSSCC registers and thus it is
impossible change clock configuration, when ethernet connection speed
changes.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patches that fix:
* Wrong MSI interrups for PCIe3
* Hang during reboot due to stopped clocks
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
CONFIG_QCOM_IPA kernel cofig was enabled by mistake and conflicts with
mac80211 as it indirectly selects QMI HELPERS. Backports project provid
his own version of QMI HELPERS hence it should not be built-in.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Make the RPM partition read-only. This was a mistake and a leftover from
staging branch but I can take this mistake as an excuse to document the
current problem with RPM.
It might happen that a board ship with a broken RPM .mbn, broken not in
the sense that the board doesn't boot or it's a brick but broken in the
sense that it's outdaed and suffer from a bug fixed in new version.
This bug consist in a problem with the regulators between USB and NSS.
The old RPM mess with the NSS regulator (l2) and change the voltage for
it while configuring the USB regulator (l5).
This cause the ethernet subsystem to malfunction with the port not
working.
To workaround this, it's needed to disable RPM handling and CPUFreq.
With these 2 disabled, the old RPM doesn't touch regulators and Ethernet
works correctly.
New RPM correctly handle regulators for USB (l5) and doesn't suffer from
this problem. A solution for this is getting discussed with QCOM hoping
to get some good feedback for it.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add pending patch fixing NSSCC boot stall. These patch are needed to
prevent the ICC to disable critical clock for NSSCC NOC.
Without these the system will stall and reboot with watchdog.
While at it also remove an extra clock from DTSI as it currently have no
use. Original patch is not modified to keep consistency with series
proposed upstream.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Drop redundant comment in NSSCC clock patch. The problem has been
identified hence the comment doesn't apply anymore.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Define default partition table for SPI-NAND mounted on reference board.
This is where is normally placed the rootfs UBI.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh dts SPI-NAND patch to to v14. This is to keep stuff synced with
current pending patch revision and make it easier to replace patch
later (and discover something broke in the meantime)
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh the NSSCC patch for new PCIe patches. To keep track of fuzz
changes for the IPQ95xx patches, patch are not refreshed currently.
For the specific case of NSSCC patch, quilt gets confused and apply the
patch in the wrong node, putting it in the RPM node (causing all kind of
funny errors at runtime)
Correctly fix the patch to put the node right after the PCIe nodes.
Also the PORT patch need to be refreshed as the gpio header is added by
the PCIe patch.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add PCIe upstream patch and related nodes to enable PCIe on IPQ95xx.
Minimal change were required to backport the patch and apply on current
kernel. Refresh all affected patch.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add USB3 kmods to the default package list, USB3 correctly works on
IPQ95xx hence it can be enabled.
While at it drop the NSS-DP as it was added by mistake as the ethrnet
platform is handled differently on this SoC with pending upstream
drivers.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
QCOM SPI NAND driver got merged upstream hence we can drop the special
patch from qualcommax and qualcommbe target and move them to the generic
backports directory to reduce patch maintenance.
While at it refresh any affected patch and target and also backport other
minor fixup for the SPI NAND driver merged upstream later.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The CONFIG_NET_SWITCHDEV option is needed by CONFIG_DSA and some other
options. It is boolean, we have to compile it into the kernel it self.
Activate it for all targets in the generic configuration, it is already
activated for most of them. This allows to install DSA drivers as a
module.
On the ramips/mt7620 target the kernel would grown by 4.5kB.
For some small targets which do not support a DSA switch by default the
option is deactivated.
Link: https://github.com/openwrt/openwrt/pull/17668
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Refreshed patches for qualcommb/ipq95xx by running
make target/linux/refresh after creating a .config containing:
CONFIG_TARGET_qualcommbe=y
CONFIG_TARGET_qualcommbe_ipq95xx=y
CONFIG_TARGET_qualcommbe_ipq95xx_DEVICE_qcom_rdp433=y
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17822
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add patch to fix Qcom SNAND driver and move the SNAND patches to
backports directory as they are shared between qualcommax and qualcommbe
target.
Fixes: #17897
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17900
Signed-off-by: Robert Marko <robimarko@gmail.com>
Set target as source-only for now as only the Reference Board is
supported and needs to better evaluated with real Devices.
Link: https://github.com/openwrt/openwrt/pull/17725
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Enable the Aquantia PHY by default in config-defaults. Target is big
enough to permit embedding the PHY instead of having as an external
module.
Link: https://github.com/openwrt/openwrt/pull/17725
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Update patch with upstream version and automatically refresh with make
target/linux/refresh.
Also backport one additional fix patch for NAND patch and drop a patch
merged upstream.
Link: https://github.com/openwrt/openwrt/pull/17725
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing unmet dependency for QCOM PPE. This fix a compilation
error when SFP config is selected.
Link: https://github.com/openwrt/openwrt/pull/17725
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patches adding partition table common to RDP board and node for AQR
NVMEM.
Link: https://github.com/openwrt/openwrt/pull/17725
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
