- Turn IPv4-Address into IPv4 address
- Turn IPv4-Gateway into IPv4 gateway
- Turn IPv6-Address into IPv6 address
- Turn IPv6-Gateway into IPv6 gateway
- Turn MAC-Address into MAC address
Also remove related duplicate translation entries.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The iptables mark field is 32 bits wide, which is 4 bytes and so 8 hex
characters. Fix the fwmark validation to allow 8 characters in the hex
string.
Fixes: #5098
Suggested-by: Robert <32970961+differentblue@users.noreply.github.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This is required to resolve clashes with the generic "option device"
referring to netdev names in current netifd versions.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Those are L2 options that are not part of interfaces (L3), should not be
set there and don't work. Setting MAC and MTU should be done at device
layer (config device) and is supported for basic types already.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The introduction of network device configuration support also implemented
all common, protocol-independent interface options directly in the
interface config view, so drop the redundant option definitions.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Prepares for 5.10 migration. wireguard-tools will bring in the correct
wireguard kernel module dependency - either kmod-wireguard or
kmod-wireguard-oot.
Depends on https://github.com/openwrt/openwrt/pull/3885
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Better handling of Type of Service (IPv4), Traffic Class (IPv6) values
Optional value Local endpoint address is detected and pre-filled in the interface
Signed-off-by: Jan Bětík <jan.betik@svine.su>
legacymap causes map to use the legacy IPv6 Interface Identifier format
that was described in draft-ietf-softwire-map-00, but was eventually
changed in RFC7597. It is however still used by some major ISPs,
including in Japan.
Signed-off-by: Remi NGUYEN VAN <remi.nguyenvan+openwrt@gmail.com>
"type" is already used as a common option for all protocols. This makes
the configuration ambiguous, and Luci sees JS errors when trying to save
a MAP configuration.
Switch to "maptype" instead to avoid the conflict. MAP currently uses
"maptype" and falls back to "type" when not specified.
Signed-off-by: Remi NGUYEN VAN <remi.nguyenvan+openwrt@gmail.com>
I'm running several GRE tunnels to different locations and
the option to see and to configure GRE tunnels in LuCI was not
crucial but nice to have.
Signed-off-by: Jan Bětík <jan.betik@svine.su>
This addresses the issue of openconnect.sh from openconnect package expecting
a vpn- suffix for the files, while the frontend didn't.
Signed-off-by: Friendly fellow <DasTestament@users.noreply.github.com>
[reword commit message]
Ref: https://github.com/openwrt/packages/issues/11584
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This change allows to configure `nohostroute` option for wireguard to explicitely prevent creation
of host routes to endpoints.
By default without `option nohostroute '1'`, an explicite route to the peer's endpoint will be created in the main routing table with the next hop to the gateway. However, it causes issues with some setup. Enabling this option will inhibit this behavior. See discussions at http://lists.openwrt.org/pipermail/openwrt-devel/2019-March/016329.html.
Signed-off-by: Yuxiang Zhu <vfreex@gmail.com>
The proto handler qmi does support the delay option for modem
initialization. Add that missing option to the advanced tab to configure
that with LuCI.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
The option maxwait is not support by the 3g netifd proto.
To standardize that rename the maxwait option to delay as in the other
proto handlers luci-proto-qmi and luci-proto-ncm.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Sometimes people only want the VPN connection to be a route to a specific
network, not the default gateway for all traffic.
I've tested this on my router and works fine!
Submitted-by: Whitronic <joao.f.vieira@gmail.com>
[reword commit message]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Disabling LCP echos by *not* setting "option keepalive" was broken in
OpenWrt since https://dev.archive.openwrt.org/ticket/2373.html so setting
"0" in LuCI had the effect of reverting back to "5, 1" while the help
suggested otherwise.
Support for "keepalive 0" was fixed with https://git.openwrt.org/555c59230
so align LuCI now to emit "option keepalive 0" instead of removing the
option when entering "0" in the gui.
Fixes#2112
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Some modems are controlled only through a tty.
Autodetection of control device is broken in ncm.sh
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Due to historical reasons, the relayd daemon configuration resides in the
form of a fake "config interface" section in /etc/config/network without
actually registering a protocol handler.
This causes netifd to emit an "INVALID_PROTO" error for the interface
which is technically correct, but confusing for LuCI users.
This situation needs to be resolved upstream by either moving relayd
configuration out of the network config, or by converting the relayd
service into a proper protocol handler.
Until this happens, do not report any netifd errors since we're not
operating on an actual interface.
While we're at it, also propagate the protocol up state from the fake
virtual device to ensure that LuCI displays the relay bridge as "up"
when all relayed interfaces are up as well.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This removes all options 100% unrelated to NCM protocol.
Some options like 'dns' are not currently used by connection scripts,
but may be used in the future.
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
The follow error will appear after clicking "Switch protcol" to 3g when
luci-proto-3g was not installed. Fix this by moving the relevant parts
from luci-proto-ppp into luci-proto-3g and making it complete as a
single protocol handler
> Missing protocol extension for proto "3g"
> cannot open /usr/lib/lua/luci/model/cbi/admin_network/proto_3g.lua: No such file or directory
Closesopenwrt/luci#1815
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
If there is no translation set, then on material theme the dropdown
selection displaced. To fix this add an translation to this dropdown.
The commit also changes source code whitespace shifting.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Make the hint message more explicit to tell users that the prefix size needs
to be specified as well.
Fixes#1559.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The virtual interface match patterns of various protocols were improperly
quoted, causing them to over- or undermatch.
Follow up of #1435.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The dash '-' needs to be escaped by a '%', otherwise it will
be interpreted as minus, which means '0 or more repetitions'.
This fixes LEDE FS#1157.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
