Reorganize backported 6.12 generic patches, grouping them by following
a standard naming XXX-XX-v6.x-patch-file-name.patch.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add kernel package for DesignWare I2C platform controller.
This controller is used on the RP1 SoC found on RPi 5 devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The ENC28J60 is a 10 Mbps half-duplex Ethernet controller interfaced via SPI.
It achieves real-world bandwidth up to 5Mbit/s on devices like the RPi Zero due
to SPI limits.
Commonly used with Raspberry Pi Zero boards for wired network connectivity.
Signed-off-by: Albrecht Lohofener <albrechtloh@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19048
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add kernel packages for DesignWare SPI core and MMIO controllers.
This is needed for the RP1 SoC found on RPi 5 devices.
Tested with a Microchip ENC28J60 Ethernet controller on a RPi 5.
Signed-off-by: Albrecht Lohofener <albrechtloh@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19049
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
building with CONFIG_ALL_KMODS unearthed all sorts of interesting
failures
ERROR: module 'crypto/chacha-x86_64.ko' is missing.
ERROR: module 'crypto/poly1305-x86_64.ko' is missing.
ERROR: module 'crypto/curve25519-x86_64.ko' is missing.
ERROR: module 'crypto/camellia-x86_64.ko' is missing.
These stem from the main UML Makefile.
|# UML only makes sense on linux
|ifeq ($(HOST_OS),Linux)
| ifeq ($(HOST_ARCH),x86_64)
|
|ARCH:=x86_64
|BOARD:=uml
The modules in question define x86_64 optimized version and
the OpenWrt's buildsystem expects that these modules will be present.
SPI is not available due to the UML Architecture not setting HAS_IOMEM.
In the future, UML could get (virtualized) IOMEM and/or SPI could drop
the HAS_IOMEM dependency. A patch for the latter has been sent:
<https://lore.kernel.org/linux-spi/20250530234941.950431-1-chunkeey@gmail.com/T/#u>
mt76: Unfortunately, the firmware packages are picked up, but the
associated drivers can't be build because iowrite32+ioread32 are
not defined.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Add uboot-envtools (removing -uboot-envtools) to devices which were
missed in the commit 79bd017 ("ramips: mt7621: add uboot-envtools to
all devices")
- Mi Router 3G
- Mi Router AC2100
While at here remove two redundant entries from devices which were added
just after the referenced commit 79bd017 and did not account for the
new DEFAULT_PACKAGES member:
- SNR-CPE-ME1
- SNR-CPE-ME2-SFP
Fixes: 79bd017 ("ramips: mt7621: add uboot-envtools to all devices")
Fixes: https://github.com/openwrt/openwrt/issues/18960
Signed-off-by: Mario Andrés Pérez <mapb_@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19012
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the following to fix builds with GCC 15.1:
https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/arch/mips/vdso?h=next-20250606&id=0f4ae7c6ecb89bfda026d210dcf8216fb67d2333
% dmesg | grep gcc
[ 0.000000] Linux version 6.6.93 (facade@redline) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 15.1.0 r29972+15-7d617804cfe7) 15.1.0, GNU ld (GNU Binutils) 2.44) #0 SMP Sat Jun 7 12:13:18 2025
Error for reference:
./include/linux/stddef.h:11:9: error: cannot use keyword 'false' as enumeration constant
11 | false = 0,
| ^~~~~
./include/linux/stddef.h:11:9: note: 'false' is a keyword with '-std=c23' onwards
./include/linux/types.h:35:33: error: 'bool' cannot be defined via 'typedef'
35 | typedef _Bool bool;
| ^~~~
./include/linux/types.h:35:33: note: 'bool' is a keyword with '-std=c23' onwards
./include/linux/types.h:35:1: error: useless type name in empty declaration [-Werror]
35 | typedef _Bool bool;
| ^~~~~~~
CC arch/mips/lib/delay.o
AR arch/mips/fw/lib/built-in.a
AR arch/mips/fw/lib/lib.a
CC arch/mips/ralink/of.o
CC fs/read_write.o
CC block/elevator.o
cc1: all warnings being treated as errors
make[9]: *** [scripts/Makefile.build:243: arch/mips/vdso/vgettimeofday.o] Error 1
make[8]: *** [scripts/Makefile.build:480: arch/mips/vdso] Error 2
Build system: x86/64
Build-tested: ramips/tplink_archer-a6-v3
Run-tested: ramips/tplink_archer-a6-v3
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/19058
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch contains various minor FDT improvements for ramips
HiWiFi series devices:
* Add mt76 driver compatibles.
* Remove useless platform compatibles.
* Add default USB LED trigger for HC5861.
* Disable unused usbphy for HC5661, HC5661A and HC581B.
* Add switch port map properties based on 02_network scripts.
* Move aliases node to device dts because the LED nodes it
references only exist in the device specific dts.
* Rename gpio-leds nodes to follow the upstream dt-bindings
suggested pattern "(^led-[0-9a-f]$|led)".
* Convert deprecated LED label property to color and function.
"system" LED has been renamed to "status", it is acceptable
because these LEDs do not have text labels.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18251
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
For all HiWiFi series devices, the base MAC address is stored on
"bdinfo" partition, offset 0x18a, ASCII text format. The recently
introduced "mac-base" nvmem layout can handle the ASCII text now,
so it's time to move MAC address configurations to dts. There is
no valid MAC info in the "factory" partition, hence they will be
replaced with the correct ones.
Tested on HiWiFi HC5661A and HC5861.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18251
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds support for RTL8814AE/RTL8814AU PCI/USB adapters.
Run-tested: x86/64/rockchip
USB adapter tested: Hawking HW17ACU Wireless-AC1750.
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19052
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds firmware support for the RTL8814AE/RTL8814AU WiFi adapters.
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19052
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Apply same patches to gmp on the host side to fix GCC 15 build errors.
31800db91d
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/18992
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add a patch in order to fix it.
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/18991
Signed-off-by: Robert Marko <robimarko@gmail.com>
Convert old style declarations to modern ones.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18600
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add a patch in order to fix it.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18600
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport two patches in order to fix it.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18600
Signed-off-by: Robert Marko <robimarko@gmail.com>
Disable -Wunterminated-string-initialization for now.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18600
Signed-off-by: Robert Marko <robimarko@gmail.com>
All patches automatically refreshed.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18600
Signed-off-by: Robert Marko <robimarko@gmail.com>
This release includes several fixes, most notable are
"-Wunterminated-string-initialization" fixes for upcoming GCC 15.x
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19011
Signed-off-by: Robert Marko <robimarko@gmail.com>
Import libxcrypt from the packages feed to the main OpenWrt repo,
as glibc 2.41 doesn't provide libcrypt (since 2.39 release).
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19011
Signed-off-by: Robert Marko <robimarko@gmail.com>
Specifications:
- SoC: Broadcom BCM6358 dual 300MHz MIPS
- Flash: 16MB NOR Spansion S29GL128P10
- RAM: 64MB DDR
- Ethernet: 4x 100M
- Wifi: Atheros AR9223
- 3x USB 2.0 port
- 4x Button
- 13x LED
- RJ11 2x FXS VoIP (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
- Assign static IP 192.168.1.100 to PC.
- Unplug the power source.
- Press the RESTART button at the router, don't release it yet!
- Plug the power source and wait at least 15 seconds.
- Release the RESTART button.
- Browse to http://192.168.1.1 with your PC.
- Upload the openwrt-bmips-bcm6358-huawei_hg556a-a-squashfs-cfe.bin file.
- Wait some minutes until the firmware upgrade completes.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Commit Fixes: 15430a1348 ("bmips: use wan ports as standalone ports")
removed bridge devices and therefore switch.1 no longer exists, so let's
use br-lan instead.
Fixes: 15430a1348 ("bmips: use wan ports as standalone ports")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
U-Boot allows specifying additional KConfig fragments to be applied on
top of a defconfig. These are usually located in the board
sub-directory.
make foo_defconfig bar.config baz.config
Add support for specifying additional KConfig fragments using the
UBOOT_CONFIG variable. Treat the first word in UBOOT_CONFIG as the name
of the defconfig, any additional words as additional fragments.
This can be useful to distinguish between different variants of U-Boot
builds such as different RAM, storage (NAND/eMMC), security etc.
While c05c0699d479 (u-boot.mk: add support for config customization,
2023-06-02) already added means to modify specific KConfig options
directly from the OpenWrt Makefile, leveraging existing fragments the
U-Boot source-dir provides a more convenient way to extend the config
when customising more than just one or two options. Furthermore it is
desirable to leverage existing fragments from upstream U-Boot where they
exist.
Signed-off-by: Andreas Gnau <andreas.gnau@iopsys.eu>
Link: https://github.com/openwrt/openwrt/pull/18963
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Arcadyan WE410443 is a WiFi AC access point distributed by various ISPs
under various names, including KPN SuperWifi and BT Whole Home Wi-Fi. It
features one ethernet port, dual MT7615N radios and four internal antennas.
Hardware:
- SoC: Mediatek MT7621AT
- Flash: 32 MB
- RAM: 128 MB
- Ethernet: 1x 10/100/1000 Mbps, built into the SoC
- WLAN: 2x MediaTek MT7615N
- Buttons: 1 Reset button, 1 WPS button
- LEDs: 1x Green, 1x Blue, 1x Red, all unmarked
- Power: 12 VDC, 1.5A barrel plug
Installation:
The bootloader is locked with a password, so the image needs to be written
directly to the SPI flash chip. To do this, you need to open up the case,
remove the heatsink and connect the flash chip to a Raspberry Pi. Use the
following connections:
Flash chip --> Raspberry Pi
VCC --> 3v3
RESET --> 3v3
/CS --> GPIO 8
DO --> GPIO 9
CLK --> GPIO 11
DI --> GPIO 10
GND --> Ground
You can solder wires to the flash chip, or use a SOIC16 clip. More details on
the Raspberry Pi and SPI chip pinouts are available on the wiki [1]
When you have the Raspberry Pi connected to the flash chip, boot your Pi and
follow the instructions:
1) Make sure your Pi has SPI enabled with sudo raspi-config
2) Install necessary tools: sudo apt install xxd libubootenv-tool mtd-utils
3) Upload overlay and execute:
sudo dtc -@ -I dts -O dtb -o
/boot/overlays/we410443.dtbo we410443-overlay.dts
4) Enable in /boot/firmware/config.txt by adding a new line containing
dtoverlay=we410443
5) Reboot your Pi and verify the mtd partitions with
cat /proc/mtd, you should see:
dev: size erasesize name
mtd0: 02000000 00001000 "all"
mtd1: 00030000 00001000 "u-boot"
mtd2: 00010000 00001000 "u-boot-env"
mtd3: 00010000 00001000 "factory"
mtd4: 01f60000 00001000 "firmware"
mtd5: 00010000 00001000 "glbcfg"
mtd6: 00010000 00001000 "config"
mtd7: 00010000 00001000 "glbcfg2"
mtd8: 00010000 00001000 "config2"
6) Optionally (but recommended), make a backup:
sudo dd if=/dev/mtd0 of=backup.bin
It can be restored with: sudo flashcp backup.bin /dev/mtd0
7) Set the variables for the bootloader:
echo '/dev/mtd2 0x0 0x1000 0x1000' > fw_env.config
sudo fw_setenv -c fw_env.config bootpartition 0
8) Finally, flash the image:
sudo flashcp openwrt-ramips-mt7621-arcadyan_we410443-
squashfs-sysupgrade.bin /dev/mtd4
MAC addresses
The label address is stored in ASCII in the config partition
Use --> Address
Device --> label
Ethernet --> label
WLAN 2g --> + 1
WLAN 5g --> + 2
References:
[1] https://openwrt.org/toh/arcadyan/astoria/we410443
Signed-off-by: Sander van Deijck <sander@vandeijck.com>
Link: https://github.com/openwrt/openwrt/pull/17981
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
- Fix MMC bus IO voltage. The GPIO voltage of mt762x series SoCs
is fixed 3.3V. There are no visible registers that can control
the voltage level. Also add "no-1-8-v" property to indicate that
MMC controller doesn't support 1.8V IO.
- Drop useless property "enable-active-high". These dummy fixed
voltage regulators are not controlled by the GPIO. We don't need
to set the GPIO polarity.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18886
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To simplify the device specific dts, reuse the mt7621 default
XHCI voltage regulators by adding the corresponding GPIO pin
and polarity properties.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18886
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We have added the default voltage regulators for the mt7621 SoC
dtsi. These redundant voltage regulators can be removed now.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18886
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The USB power regulators are essential for the Mediatek XHCI
controller. If any of them is missing, the kernel will throw
a warning. Add fixed voltage io/vbus regulators to workaround
this issue. Fix the following warnings:
[ 7.514572] xhci-mtk 1e1c0000.xhci: supply vbus not found, using dummy regulator
[ 7.522375] xhci-mtk 1e1c0000.xhci: supply vusb33 not found, using dummy regulator
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18886
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The WR3000E has the same board layout as the WR3000S. Differences:
- Different flash chip
- LEDs with red/blue colour intead of white
Hardware:
- MediaTek MT7981 WiSoC
- 256MB DDR3 RAM
- 128MB SPI-NAND (F50L1G41LB)
- MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
MAC Addresses in OEM firmware:
- There is one on the label, e.g. AA:BB:CC:DD:EE:FF
- WLAN (2.4G) uses the same as on the label
- WLAN (5G) is the one on the label but
- first byte (e.g. AA) + 2
- fourth byte (e.g. DD) - 0x40
- WAN is the one on the label + 1
- LAN is the one on the label
MAC Addresses in OpenWrt:
- Same handling as in WR3000s is used
GPIO:
- 2 Buttons (all low active):
- WPS on GPIO 0
- Reset on GPIO 1
- 6 LEDs (all low active):
- Power: Blue on GPIO 8, no red LED
- WPS: Blue on GPIO 10, Red on GPIO 4
- Internet: Blue on GPIO 11, no red LED
- LAN: Blue on GPIO 9, Red on GPIO 5
- WiFi 2.4G: Blue on GPIO 6, no red LED
- WiFi 5G: Blue on GPIO 7, no red LED
Disassembly:
- Remove the 4 screws at the bottom of the case
- Cover is clipped to the bottom part of the case with clips in the front and the back
UART:
- UART pins are accessible on the bottom of the board
- The connector with the square shape is TX
- Pins: [ ] TX, ( ) RX, ( ) GND, ( ) VCC
- Settings: 115200 8N1 3.3V
Migration to OpenWrt via OEM firmware:
- There should be a migration image available from Cudy as soon as there is official OpenWrt support
- Download the migration image via OEM web interface
- After flashing, OpenWrt is accessible via 192.168.1.1
- Flash the official OpenWrt image
Migration to OpenWrt using TFTP:
- Connect UART as described above
- Press the reset button while powering on the device
- U-Boot will now try to load a recovery.bin via TFTP, this must be ignored
- After detecting a timeout, the U-Boot console is available via UART
- Set up a TFTP server on IP 192.168.1.88 and connect it to one of the LAN ports
- Provide the initramfs image via TFTP as cudy3000e.bin
- Run the following command in U-Boot: tftpboot 0x46000000 cudy3000e.bin; bootm 0x46000000
- OpenWrt initramfs image is now booting and accessible via 192.168.1.1
- Flash the sysupgrade image
Revert back to OEM:
- Set up a TFTP server on IP 192.168.1.88 and connect it to one of the LAN ports
- Provide the Cudy firmware via TFTP as recovery.bin
- Press the reset button while powering on the device
- Recovery process will start now
- After recovery is done, the OEM firmware is available at 192.168.10.1 again
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18609
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Perl modules use double-colon naming.
Signed-off-by: Jan Pazdziora <jan.pazdziora@code.adelton.com>
Link: https://github.com/openwrt/openwrt/pull/19047
Signed-off-by: Robert Marko <robimarko@gmail.com>
The plumbing is there in the ucode files to set the parameter using
nl80211. However, the option is never forwarded because it was missing
in mac80211.sh. Add it there and in the schema file.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Link: https://github.com/openwrt/openwrt/pull/19030
Signed-off-by: Robert Marko <robimarko@gmail.com>
61ae5732adea iprule: amend ipproto netlink nla_put_u32 to nla_put_u8
d610d68c71b8 device: add support for configuring vrf
a1b6386a20a6 device: fix bonding primary port selection
e8bbf246ce2e system-linux: fix sysfs name for all_ports_active flag
723c699e84f4 Restore disable_ipv6 sysctl after removing a device from bridge or bond
d476e18e8d43 iprule: resolve ipproto by name
7901e66c5f27 netifd: iprule add sport and dport
Signed-off-by: Robert Marko <robimarko@gmail.com>
Inverted condition caused wrong value for eht_oper_centr_freq_seg0_idx
get selected in ETH320 mode, causing AP fail to start.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18998
Signed-off-by: Robert Marko <robimarko@gmail.com>
With the recent fixes backported to 6.12, b53 ports should now fully
work as standalone ports outside of a switch.
So move them out of the switch and use them as standalone ports, which
makes configuring easier as VLANs don't need to be defined and reserved
anymore to use the wan port.
Tested on DGND3700v1.
While most devices do not define a wan port, I dropped the
ucidef_set_bridge_device() from all devices for consistency.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Allow selecting 6.12 as testing kernel on imx.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19029
Signed-off-by: Nick Hainke <vincent@systemli.org>
Linux 6.8 changed the directory structure for the video-code driver.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19029
Signed-off-by: Nick Hainke <vincent@systemli.org>
patches:
- remove patches from 6.7-6.12 that are now upstream.
- refresh remaining patches
- 502-6.13-arm64-dts-freescale-rename-gw7905-to-gw75xx.patch was
misnamed as that patch went upstream in 6.12 and thus is also removed
- 504-6.13-arm64-dts-imx-Add-i.MX8M-Plus-Gateworks-GW82XX-2X-support.patch
was refreshed to the final version that was accepted upstream
- 600-PCI-imx6-Start-link-at-max-gen-first-for-IMX8MM-and-IMX8MP.patch
was removed while I investigate an upstream approach for the issue
it was working around.
configs:
- config-6.12: unset new configs not needed for all cortexa7/a9/a53
- cortexa53/config-default: added new CONFIG_PCI_IMX6_HOST config for cortexA53 (IMX8M)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19029
Signed-off-by: Nick Hainke <vincent@systemli.org>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19029
Signed-off-by: Nick Hainke <vincent@systemli.org>
