TP-Link EAP625-Outdoor HD is a 802.11ax AP claiming AX1800 support.
It is wall or pole mountable, and rated for outdoor use. It can only
be powered via PoE.
Hardware-wise, it is very similar to the older EAP610-Outdoor model.
Software-wise, I couldn't find a difference other than the board
data files, and device name. For this reason, the majority of the
devicetree from the EAP610-Outdoor is reused.
This device currently comes in a "v1", and "v1.6" version. The
"support-list" of the vendor firmware does not have a distinction
between these versions. This commit was tested on a 'V1.6" device.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512 MB
* Storage: 128MB NAND
* Ethernet:
* Gigabit RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Multi-color System LED (Green/Amber)
* Buttons:
* 1x Reset
* UART: 4-pin unpopulated header
* 1.8 V level, Pinout 1 - TX, 2 - RX, 3 - GND, 4 - 1.8V
Installation:
=============
Web UI method
-------------
Set up the device using the vendor's web UI. After that go to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
The connect to the machine via SSH:
ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>
Disable signature verification:
cliclientd stopcs
Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
* Go to System -> Firmware Update.
* Under "New Firmware File", click "Browse" and select the image
* Select "Update" and confirm by clicking "OK".
If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWRT.
NOTE: If ssh continues to complain that "no matching host key type
found. Their offer: ssh-rsa,ssh-dss" it likely means that yor distro
has completely disabled deprecated siphers in ssh. In that case, run
the ssh command from a docker container of an older distro.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot tplink_eap625-outdoor-hd-v1-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the commandline.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18584
Signed-off-by: Robert Marko <robimarko@gmail.com>
It was suggested that the pinctrl property of the mdio node should
include the PHY reset GPIO. Add them in.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18584
Signed-off-by: Robert Marko <robimarko@gmail.com>
I have an EAP625-Outdoor HD v1 that is very similar with the EAP610
Outdoor. It works with the EAP610 initramfs, without any obvious loss
of functionality. In order to prepare for supporting the EAP625, move
the common parts into a shared .dtsi.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18584
Signed-off-by: Robert Marko <robimarko@gmail.com>
It's the proper function to handle this stuff in.
The original patch abused the fact that the ath9k driver in init called
ath9k_init_platform to populate all the needed configuration. This is
the wrong place to do so and it also goes away in 6.13.
Move 553-ath9k_of_gpio_mask.patch contents to ath9k_of_init where they
belong.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18764
Signed-off-by: Robert Marko <robimarko@gmail.com>
The web-recovery of the Genexis EX400 validates uploaded images to fit
in the rootf_0 partition.
With OpenWrt, only the kernel is stored in this partition, leaving the
partition very small. Currently, the first factory release image won't
be accepted by the recovery interface after the OpenWrt installation.
Pad the image of the ubifs to 10MB. This allows the 24.10 release image
to be uploaded, enabling device recovery.
Signed-off-by: David Bauer <mail@david-bauer.net>
Clean the temporary directory the UBI image is generated from before
generation.
Currently it is removed after the image generation, which leads to files
possibly not being cleared after a build failure in this step.
Signed-off-by: David Bauer <mail@david-bauer.net>
bcm6328, bcm6362 and bcm6368 targets are missing a key config symbol which
prevents the NAND from working.
Fixes: f6c02b014d ("bmips: 6.1: refresh config and add missing symbols")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
CONFIG_PAHOLE_HAS_LANG_EXCLUDE is set depending on the pahole version
present, so it must be filtered out.
Signed-off-by: Robert Marko <robimarko@gmail.com>
During the build of perl, the following ICE was reported in
https://github.com/openwrt/packages/issues/24565 when targeting PowerPC:
during RTL pass: reload
blocksort.c: In function 'mainSort.isra':
blocksort.c:1011:1: internal compiler error: in patch_jump_insn, at cfgrtl.cc:1303
1011 | }
| ^
0x7d49cee29d8f __libc_start_call_main
../sysdeps/nptl/libc_start_call_main.h:58
0x7d49cee29e3f __libc_start_main_impl
../csu/libc-start.c:392
Please submit a full bug report, with preprocessed source (by using -freport-bug).
Please include the complete backtrace with any bug report.
See <http://bugs.openwrt.org/> for instructions.
The same issue also caused the CI failures in
https://github.com/openwrt/packages/pull/26501.
The issue only occurs with GCC 14.2.0, but not with the head of the
releases/gcc-14 maintenance branch; a bisect found that this patch fixes
it.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/18797
Signed-off-by: Robert Marko <robimarko@gmail.com>
For kernel 6.12 there is a warning causing an error:
drivers/mtd/nand/mtk_bmt_v2.c: In function 'mtk_bmt_get_mapping_mask':
drivers/mtd/nand/mtk_bmt_v2.c:307:31: error: 'kmalloc_array_noprof' sizes specified with 'sizeof' in the earlier argument and not in the later argument [-Werror=calloc-transposed-args]
307 | used = kcalloc(sizeof(unsigned long), BIT_WORD(bmtd.bmt_blk_idx) + 1, GFP_KERNEL);
| ^~~~~~~~
Swapping the arguments solves the problem.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18701
Signed-off-by: Robert Marko <robimarko@gmail.com>
Adjust the 'inline' declaration order to fix the build warning:
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xway/ltq-adsl-mei-danube/ltq-adsl-mei/drv_mei_cpe.c:188:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
188 | static void inline MEI_MASK_AND_ACK_IRQ(int x)
| ^~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
fix inline declaration warning
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
There are a lot of missing-prototypes warnings, It's not worth to
fix them one by one. Let us just ignore them.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix incomplete type error by including the correct header.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
* Mark some functions as static.
* Add missing prototypes.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
These functions return the register memory addresses. Usually
they are fixed values, hence I think it's safe to remove the
qualifier "volatile".
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
Convert .remove to .remove_new so that it can be compatible with
both 6.6 and 6.12 kernels.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
* Mark some functions as static.
* Include function prototypes header file.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
Adjust the 'inline' declaration order to fix the build warning.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
Include missing header "drv_vmmc_api.h" to fix the compilation errors.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add LANTIQ prefix to workaround the build warnings.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
There are a lot of missing-prototypes warnings, It's not worth to
fix them one by one.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
NULL and fixed addresses are constant, const qualifier are useless.
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_ar9.c:47:1: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
47 | const void (*ifx_bsp_basic_mps_decrypt)(unsigned int addr, int n) = NULL;
| ^~~~~
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_ar9.c:246:49: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
246 | ifx_bsp_basic_mps_decrypt = (const void (*)(unsigned int, int))0xbf0017c4;
| ^~~~~
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_ar9.c:249:49: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
249 | ifx_bsp_basic_mps_decrypt = (const void (*)(unsigned int, int))0xbf001ea4;
| ^~~~~
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/drv_vmmc-1.9.0/src/mps/drv_mps_vmmc_ar9.c:252:49: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
252 | ifx_bsp_basic_mps_decrypt = (const void (*)(unsigned int, int))0xbf001f38;
| ^~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix incomplete type error by including the correct header.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add missing header to fix the build errors on 6.12 kernel.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
Mark cgu_get_pp32_clock() as static.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch fixes the following build warnings by adding
missing prototypes:
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xway/ltq-deu-danube/ltq-deu/ifxmips_deu_danube.c💯5: error: no previous prototype for 'input_swap' [-Werror=missing-prototypes]
100 | u32 input_swap(u32 input)
| ^~~~~~~~~~
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xway/ltq-deu-ar9/ltq-deu/ifxmips_deu_ar9.c:91:5: error: no previous prototype for 'input_swap' [-Werror=missing-prototypes]
91 | u32 input_swap(u32 input)
| ^~~~~~~~~~
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xway/ltq-deu-ar9/ltq-deu/ifxmips_deu_ar9.c:131:6: error: no previous prototype for 'chip_version' [-Werror=missing-prototypes]
131 | void chip_version(void)
| ^~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch fixes various missing-prototypes build warnings by:
* Mark some functions as static.
* Add missing prototypes.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch fixes various missing-prototypes build warnings on
6.12 kernel.
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_ase/ltq-atm-ase/ltq-atm/ifxmips_atm_amazon_se.c:257:13: error: no previous prototype for 'ase_fw_ver' [-Werror=missing-prototypes]
257 | extern void ase_fw_ver(unsigned int *major, unsigned int *minor)
| ^~~~~~~~~~
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_ase/ltq-atm-ase/ltq-atm/ifxmips_atm_amazon_se.c:266:5: error: no previous prototype for 'ase_init' [-Werror=missing-prototypes]
266 | int ase_init(struct platform_device *pdev)
| ^~~~~~~~
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_ase/ltq-atm-ase/ltq-atm/ifxmips_atm_amazon_se.c:283:6: error: no previous prototype for 'ase_shutdown' [-Werror=missing-prototypes]
283 | void ase_shutdown(void)
| ^~~~~~~~~~~~
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_ase/ltq-atm-ase/ltq-atm/ifxmips_atm_amazon_se.c:297:5: error: no previous prototype for 'ase_start' [-Werror=missing-prototypes]
297 | int ase_start(int pp32)
| ^~~~~~~~~
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_ase/ltq-atm-ase/ltq-atm/ifxmips_atm_amazon_se.c:323:6: error: no previous prototype for 'ase_stop' [-Werror=missing-prototypes]
323 | void ase_stop(int pp32)
| ^~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
Mark some functions as static to fix various missing-prototypes
build warnings on 6.12 kernel.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
fix undefined type error:
/home/db/owrt/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/ltq-atm-vr9/ltq-atm/ltq_atm.c:1776:43: error: invalid use of undefined type 'const struct of_device_id'
1776 | ops = (struct ltq_atm_ops *) match->data;
| ^~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
This package is maintained by the OpenWrt local repository. There
is no need to modify it with the patch file. Just apply all patches
to the source files.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
Mark some functions as static.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
* Mark some functions as static.
* Include function prototypes header file.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
* Mark some functions as static.
* Include function prototypes header file.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
These functions return the register memory addresses. Usually
they are fixed values, hence I think it's safe to remove the
qualifier "volatile".
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
Convert .remove to .remove_new so that it can be compatible with
both 6.6 and 6.12 kernels.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add prototype definition for exported function ifx_mei_atm_led_blink().
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add prototype definition for exported function IFX_Var_Fifo_getRoom().
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add LANTIQ prefix to avoid name conflicts.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
PCI_IRQ_LEGACY was renamed to PCI_IRQ_INTX for kernel 6.10. Fix
compilation error:
/home/db/owrt/build_dir/target-arm_cortex-a7+neon-vfpv4_musl_eabi/linux-ipq40xx_generic/vrx518_ep-2.1.0/ep.c:469:69: error: 'PCI_IRQ_LEGACY' undeclared (first use in this function); did you mean 'NR_IRQS_LEGACY'?
469 | err = pci_alloc_irq_vectors(pdev, nvec, nvec, PCI_IRQ_MSI | PCI_IRQ_LEGACY);
| ^~~~~~~~~~~~~~
| NR_IRQS_LEGACY
Signed-off-by: Andre Heider <a.heider@gmail.com>
Co-authored-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18744
Signed-off-by: Robert Marko <robimarko@gmail.com>
Kernel does
if (phydev->drv->set_loopback)
ret = phydev->drv->set_loopback(phydev, enable, speed);
else
ret = genphy_loopback(phydev, enable, speed);
So no need to explicitly set genphy_loopback() in phy_driver. Drop
references to let kernel do its work.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18782
Signed-off-by: Robert Marko <robimarko@gmail.com>
PCI paths of IPQ50xx devices have changed now that linux,pci-domain is set
in the DTSI, so add a migration script for wireless config.
Link: https://github.com/openwrt/openwrt/pull/18789
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that IPQ50xx PCIe nodes have linux,pci-domain property defined
it changed the PCI path, but its now predictable and fixed.
So, update the caldata script accordingly.
Link: https://github.com/openwrt/openwrt/pull/18789
Signed-off-by: Robert Marko <robimarko@gmail.com>
Unlike other buses, for PCIe child nodes we should not use "wifi@1,0" as
the bus adress since for PCI devices the actual device adress on the bus is
actually set via the "reg" property and the node name is unused completely.
Though, it will cause DTC to throw warnings, so after investigation and
similar issue upstream[1] simply set the nodes to "wifi@0,0" instead.
[1] https://lists.infradead.org/pipermail/linux-arm-kernel/2021-August/680846.html
Link: https://github.com/openwrt/openwrt/pull/18789
Signed-off-by: Robert Marko <robimarko@gmail.com>
PCIe bridge nodes are now present in the SoC DTSI, so drop our downstream
ones as otherwise ath1*k BDF matching will fail.
Link: https://github.com/openwrt/openwrt/pull/18789
Signed-off-by: Robert Marko <robimarko@gmail.com>
It seems that bus-range property was missed for the PCIe bridges on
IPQ50xx, thus causing DTC to warn on any bus adress used on nodes
under the PCIe bridges.
Link: https://github.com/openwrt/openwrt/pull/18789
Signed-off-by: Robert Marko <robimarko@gmail.com>
