Add/enable 2nd USB bus (integrated ath3k bluetooth) to dts. This already
exists in the qca956x dtsi, adding the pointer here to bring the bluetooth to life.
The 2nd bus hosts the integrated bluetooth at 0x1b400000.
See in the comments for more info:
c5b7ec8cee
Tested-by: Russ Innes <russ.innes@gmail.com> on Ubiquiti Amplifi HD .
Signed-off-by: Russ Innes <russ.innes@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19303
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This device is similar to the TP-Link EX220 v1.
The differences are the number of ports (3 LANs
and 1 WAN) and the number of LEDs (1 LED RGB)
Hardware
--------
CPU: MediaTek MT7621 DAT
RAM: 128MB DDR3 (integrated)
FLASH: 16MB SPI-NOR
WiFi: MediaTek MT7905 + MT7975 (2.4 / 5 DBDC) 802.11ax
SERIAL: 115200 8N1
LED - (TX - RX - GND - 3V3 ) - ETH ports
Installation
------------
Flashing is only possible via a serial connection using the sysupgrade
image; the factory image must be signed. You can flash the sysupgrade
image directly through the U-Boot console, or preferably, by booting the
initramfs image and flashing with the sysupgrade command. Follow these
steps for sysupgrade flashing:
1. Establish a UART serial connection.
2. Set up a TFTP server at 192.168.0.2 and copy the initramfs image
there.
3. Power on the device and press any key to interrupt normal boot.
4. Load the initramfs image using tftpboot.
5. Boot with bootm.
6. If you haven't done so already, back up all stock mtd partitions.
7. Copy the sysupgrade image to the router.
8. Flash OpenWrt through either LuCI or the sysupgrade command. Remember
not to attempt saving settings.
Revert to stock firmware
------------------------
Flash stock firmware via OEM web-recovery mode. If you don't have access
to the stock firmware image, you will need to restore the firmware
partition backed up earlier.
Web-Recovery
------------
The router supports an HTTP recovery mode:
1. Turn off the router.
2. Press the reset button and power on the device.
3. When the LED start flashing, release reset and quickly press it
again.
The interface is reachable at 192.168.0.1 and supports installation of
the OEM factory image. Note that flashing OpenWrt this way is not
possible, as mentioned above.
Signed-off-by: Gustavo Curi <gpcuri@land.ufrj.br>
Link: https://github.com/openwrt/openwrt/pull/19104
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add uboot-envtools support for Gateworks venice boards based on i.MX8M
SoC's (imx_cortexa53) which boot from and store their U-Boot env on
eMMC boot0 hardware partition.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19347
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since not every device sets an ubifs partition name as the same as their
parent mtd partition, this change allows mount_ubi_part to usable in
other devices
Signed-off-by: Yonghyu Ban <yhban@silicon.moe>
Link: https://github.com/openwrt/openwrt/pull/19203
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
**Huasifei WH3000 Pro**
Portable Wi-Fi 6 travel router based on MediaTek MT7981A SoC. MT7981B+MT7976CN+RTL8221B Dual Core 1.3GHZ with 5G modems module and PWM Fan.
**Specifications**
SoC: Filogic 820 MT7981A (1.3GHz)
RAM: DDR4 1GB
Flash: eMMC 8GB
WiFi: 2.4GHz and 5GHz with 3 antennas
Ethernet:
1x WAN (10/100/1000M)
1x LAN (10/100/1000/2500M)
USB: 1x USB 3.0 port
Two buttons: power/reset and mode (BTN_0)
LEDS: blue, red, blue+red=pink
UART: 3.3V, TX, RX, GND / 115200 8N1
**Installation via U-Boot rescue**
1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1
2. Connect to the WAN port and hold the reset button while booting the device.
3. Wait for the LED to blink 5 times, and release the reset button.
4. Open U-boot web page on your browser at http://192.168.1.1
5. Select the OpenWRT sysupgrade image, upload it, and start the upgrade.
6. Wait for the router to flash the new firmware.
7. Wait for the router to reboot itself.
**Installation via sysupgrade**
Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings.
**Installation via SSH**
Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command:
```
sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000-pro-squashfs-sysupgrade.bin
```
**Factory MAC**
You can find your Factory MAC which is mentioned on the box at `/dev/mmcblck0p2` partition `factory` starting from `0x4`
```
dd if=/dev/mmcblk0p2 bs=1 skip=4 count=6 | hexdump -C
```
Cherry-picked from 949d0bd77a
Fixed `green` to `blue` LED in dts, added `SUPPORTED_DEVICES += huasifei,fudy-pro` - to make sysupgrade compatible with factory QWRT/Lede fork firmware.
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19315
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Upstream has disabled SHA-1 algorithms by default since version 2025.87.
SHA-1 has known weakness and most SSH implementations support alternatives.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
It's hard or even impossible to track affected sources
so it's safe to remove all built objects (if any).
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
This allows to fine-tune dropbear build options.
This change is heavily based on similar work done by Marius Dinu earlier
so I'd like to say many thanks to original author.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
- update dropbear to latest stable 2025.88;
for the changes see https://matt.ucc.asn.au/dropbear/CHANGES
- rewrite 100-pubkey_path.patch
- refresh remaining patches
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
The operating mode of a SerDes must be aligned with the attached PHY or
SFP module. That does not only require to change the protocol (e.g. SGMII,
10Gbase-R, ...) but also the speed (e.g. 1.25G). For this the SerDes must
be re-initialized properly.
- It must be taken into power down
- The PLL speed must be set
- Maybe the CMU (clock management unit) must be resetted
- The new mode must be set
- The state machine must be resetted
- The power must be reactivated
Until now this sequence is bugged. First the driver relies on a clean
setup from U-Boot (rtk network on) and second trying to to change mode
and PLL speeds does not work at all. And not to forget: Currently two
adjacent SerDes cannot drive SGMII/HSGMII at the same time. Fix this by
taking care about the right SerDes/PLL/CMU command init order.
P.S. This code is inspired by the work of Jan Hofmann, who tried to
enable parallel SGMII/HSGMII mode. The only missing bit was a proper CMU
reset sequence.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19220
Signed-off-by: Robert Marko <robimarko@gmail.com>
Correctly load the list of basic_rates from UCI. basic-rates shall be
stored as a option-list. The current code did not retrieve this list
correctly.
wpa_supplicant uses a different config option to set basic-rates
when operating in mesh-mode.
Use the correct config key and calculation for mesh-interfaces.
Signed-off-by: David Bauer <mail@david-bauer.net>
Since upstream commit:
b809fc656e763296f227b9b31e8f225e5977a8af ("perf build: Shellcheck support
for OUTPUT directory")
perf will attempt to run shellcheck on the test shell scripts, however
there is no point in doing this in OpenWrt and while perf checks for
shellcheck presence on your host it can fail to build in some cases.
So, simply disable it for now.
Link: https://github.com/openwrt/openwrt/pull/19361
Signed-off-by: Robert Marko <robimarko@gmail.com>
BUILD_BPF_SKEL was set to 1 by default in upstream commit:
9925495d96efc14d885ba66c5696f664fe0e663c ("perf build: Default
BUILD_BPF_SKEL, warn/disable for missing deps")
Prior to that, it was disabled by default and you had to enable it to
build BPF skeleton support.
So in order to fix perf compilation with kernel 6.12, lets disable
BUILD_BPF_SKEL.
Fixes: #19310
Link: https://github.com/openwrt/openwrt/pull/19361
Signed-off-by: Robert Marko <robimarko@gmail.com>
Changing the node names arbitrarily broke existing configurations, which
rely on the device path in /etc/config/wireless.
Revert that part of the change without altering the compatible strings.
Fixes: 7e09959efd ("mac80211: fix wmac node names")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The RTL8261N driver does not work correctly on non-mediatek devices. Remove
some of the power controls for Realtek chips.
This assumes the network has been started by the bootloader already:
(rtk network on).
Co-authored-by: Sebastian Gottschall
- bf45143f03
- 2fb02a5745
- 598a16a8d8
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19081
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for the RTL8264 (quad-10G phy) by matching the appropriate PHY_ID
in the driver.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19081
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update to 6.5.
Removed patch from pre-2012: 101-ncurses-5.6-20080628-kbs.patch
Build system: x86/64
Build-tested: x86/64-glibc
Run-tested: x86/64-glibc
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/19335
Signed-off-by: Robert Marko <robimarko@gmail.com>
Without the newly introduced flag, building with libc ends in errors such the below.
There is an upstream fix[1], but backporting it is not straight forward.
/scratch/union/staging_dir/toolchain-x86_64_gcc-15.1.0_glibc/x86_64-openwrt-linux-gnu/include/c++/15.1.0/cstddef:81:21: error: redefinition of 'struct std::__byte_operand<unsigned char>'
81 | template<> struct __byte_operand<unsigned char> { using __type = byte; };
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
/scratch/union/staging_dir/toolchain-x86_64_gcc-15.1.0_glibc/x86_64-openwrt-linux-gnu/include/c++/15.1.0/cstddef:78:21: note: previous definition of 'struct std::__byte_operand<unsigned char>'
78 | template<> struct __byte_operand<bool> { using __type = byte; };
| ^~~~~~~~~~~~~~~~~~~~
make[4]: *** [Makefile:438: ../obj_s/cursesp.o] Error 1
1. https://ncurses.scripts.mit.edu/?p=ncurses.git;a=commit;h=394a1a6cf317912584592e33184ef550e738a4b9
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/19335
Signed-off-by: Robert Marko <robimarko@gmail.com>
Split the xcrypt package build into two Makefiles and a common part for
the version definition in order to work-around build problems when
combining VARIANT with BUILDONLY and scoped InstallDev.
This is done in order to skip build of libcrypt-compat in case we are
not building against glibc in order to prevent libcrypt.so shared
library being present in staging_dir and by that breaking multiple
packages which then will link against it.
Fixes: e3cf7088f1 ("libcrypt-compat: introduce package")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://github.com/openwrt/openwrt/pull/19353
Signed-off-by: Robert Marko <robimarko@gmail.com>
GCC 14+ fails to build due to libatomic specific -march handling.
This build error triggers only with glibc and not with musl libc
which is default.
It seems that this patch from GCC14 was forgotten when GCC15 support was
being added [1].
[1] 44ef343500
Fixes: 68cb84183e ("toolchain: add support for GCC 15.1")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update to latest version. All patches are automatically refreshed.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19341
Signed-off-by: Nick Hainke <vincent@systemli.org>
Replace .remove_new with .remove for compatibility with future kernel versions.
Dropping compatibility with older kernels.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/19320
Signed-off-by: Nick Hainke <vincent@systemli.org>
Drop configs and patches for Linux 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/19320
Signed-off-by: Nick Hainke <vincent@systemli.org>
Switch to Linux kernel version 6.12.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/19320
Signed-off-by: Nick Hainke <vincent@systemli.org>
6df761e0e6c7 mt76: fix signature of platform_driver remove funtions for newer kernels
5724be1a6b12 wifi: mt76: Replace strlcpy() with strscpy()
c4a114e2b8c9 wifi: mt76: fix queue assignment for deauth packets
243e572d89fc wifi: mt76: add a wrapper for wcid access with validation
e41c7785589f wifi: mac80211: get tx power per link
d70f62b8f1c7 wifi: mt76: fix vif link allocation
7b3cd3274a24 wifi: mt76: mt7996: Fix secondary link lookup in mt7996_mcu_sta_mld_setup_tlv()
cf89b6218043 wifi: mt76: mt7996: Rely on for_each_sta_active_link() in mt7996_mcu_sta_mld_setup_tlv()
d71108eedab1 wifi: mt76: mt7996: Do not set wcid.sta to 1 in mt7996_mac_sta_event()
32f8c5849ed1 wifi: mt76: mt7996: Fix mlink lookup in mt7996_tx_prepare_skb
ffff9f71e29d wifi: mt76: mt7996: Fix possible OOB access in mt7996_tx()
afe63e758196 wifi: mt76: mt7996: Fix valid_links bitmask in mt7996_mac_sta_{add,remove}
68dd28b99dad wifi: mt76: mt7996: Add MLO support to mt7996_tx_check_aggr()
293778652452 wifi: mt76: mt7996: Move num_sta accounting in mt7996_mac_sta_{add,remove}_links
a94166b21e20 wifi: mt76: Get rid of dma_sync_single_for_device() for MMIO devices
87873d854e51 wifi: mt76: mt7925: Fix null-ptr-deref in mt7925_thermal_init()
06ba3d5e91f4 wifi: mt76: mt792x: Limit the concurrent STA and SoftAP to operate on the same channel
b9f4e0df317d wifi: mt76: mt792x: improve monitor interface handling
ec95319fd3fb wifi: mt76: mt7921s: Introduce SDIO WiFi/BT combo module card reset
dd2d862251cb firmware: add missing mt7990 eeprom files
05eaa56bc7a4 firmware: update mt7992 firmware to 20250328
32ca2b6db354 firmware: update mt7996 firmware to 20250328
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The upstream submission for this mandates the node to be named wifi
instead of wmac. Change all ath79 entries to match the new names and
remove the compatibility patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19328
Signed-off-by: Robert Marko <robimarko@gmail.com>
Comes with kernel 6.16. I assume it will be backported at some point.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19329
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k ahb patch was updated to match the latest upstream version,
however the openwrt DT files still use the older names.
Add those as extra entries in order to remain compatible until DT files
are fixed.
Fixes: 88f4c32060 ("mac80211: update to version 6.14.11")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
nl80211 events were propagated to the wrong interfaces
Fixes: 2ac791e87d ("hostapd: update to version 2025-06-27")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
