Hardware
--------
SOC: MediaTek MT7981b
RAM: 256MB DDR3
FLASH: 128MB SPI-NAND (Winbond W25N01GV)
WIFI: Mediatek MT7981b DBDC 802.11ax 2.4/5 GHz
ETH: MediaTek MT7531 Switch
UART: 3V3 115200 8N1 (Pinout silkscreened / Do not connect VCC)
Installation
-----------------------------------------------------------
Vendor-UI Method
-----------------------------------------------------------
1. Download the OpenWrt initramfs.trx image.
2. Connect the PC via LAN to one of the yellow router ports and wait
until your PC to get a DHCP lease.
3. Browse to http://192.168.50.1
4. If your router is brand new, finish the setup process and log into
the Web-UI.
5. Navigate to Administration -> Firmware Upgrade and upload the
downloaded OpenWrt image.
6. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
-----------------------------------------------------------
TFTP Method
-----------------------------------------------------------
1. Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.70/24. Rename the image to rtax52.bin.
2. Connect the PC with TFTP server to the RT-AX52.
Set a static ip on the ethernet interface of your PC.
(ip address: 192.168.1.70, subnet mask:255.255.255.0)
Conect to the serial console,
interrupt the autoboot process by pressing '4' when prompted.
3. Download & Boot the OpenWrt initramfs image.
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 rtax52.bin
$ bootm 0x46000000
4. Wait for OpenWrt to boot. Transfer the sysupgrade image to the device
using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
---------------------------------------------------------------------------
Revert to stock firmware:
1: Download the rt-ax52 firmware from ASUS official website. Save
the firmware to tftp server directory and rename to RT-AX52.trx
2: Connect the PC with TFTP server to the RT-AX52.
Set a static ip on the ethernet interface of your PC.
(ip address: 192.168.1.70, subnet mask:255.255.255.0)
3: Conect to the serial console, power on again, interrupt the
autoboot process by pressing '4' when prompted.
$: ubi remove linux
$: ubi remove jffs2
$: ubi remove rootfs
$: ubi remove rootfs_data
$: ubi create linux 0x45fe000
$: reset
Then the dut will reboot,interrupt the autoboot process by
pressing '2' when prompted.
2: Load System code then write to Flash via TFTP.
Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)
$: enter y
you will see the follow, type enter directly:
Input device IP (192.168.1.1) ==:
Input server IP (192.168.1.70) ==:
Input Linux Kernel filename (RT-AX52.trx) ==:
4: wait for the device run up
Based on support for ASUS RT-AX52 by liudongdongdong7397
and trx image generation by remittor
Signed-off-by: Christoph Krapp <achterin@gmail.com>
This commit fixes mistaken executable bit on
mt7981b-mercusys-mr80x-v3.dts file.
Fixes: 7921e48d43 ("mediatek: add support for Mercusys MR80X v3")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
YAFFS support in U-Boot is basically abandoned and will even fail to
build with GCC14, so simply disable it.
Link: https://github.com/openwrt/openwrt/pull/18598
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add missing semicolon to the end of the property.
Remove whitespace while at it.
Fixes: 5a3b9d88f1 ("lantiq: Improve support for LED's fritz736x")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/18594
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix nand-ecc-strength property in the spi-nand node of GL-iNet GL-B3000
to 4, to solve the following ECC error on that spi-nand chip.
[ 1.551618] ubi0: attaching mtd11
[ 1.552331] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 0:0, read only 64 bytes, retry
[ 1.554455] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 0:0, read only 64 bytes, retry
[ 1.565931] ubi0 warning: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 0:0, read only 64 bytes, retry
[ 1.576568] ubi0 error: ubi_io_read: error -74 (ECC error) while reading 64 bytes from PEB 0:0, read 64 bytes
[ 1.587146] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 6.6.87 #0
[ 1.597153] Hardware name: GL.iNet GL-B3000 (DT)
[ 1.602881] Call trace:
[ 1.607739] dump_backtrace+0xa0/0xe0
[ 1.609910] show_stack+0x18/0x24
[ 1.613728] dump_stack_lvl+0x48/0x60
[ 1.617027] dump_stack+0x18/0x24
[ 1.620672] ubi_io_read+0x11c/0x32c
[ 1.623972] ubi_io_read_ec_hdr+0x50/0x1f0
[ 1.627618] ubi_attach+0x35c/0x133c
[ 1.631524] ubi_attach_mtd_dev+0x494/0xaf4
[ 1.635257] ubi_init_attach+0xac/0x2e4
[ 1.639163] do_one_initcall+0x6c/0x1fc
[ 1.642983] kernel_init_freeable+0x204/0x2e4
[ 1.646803] kernel_init+0x28/0x1dc
[ 1.651316] ret_from_fork+0x10/0x20
The GL-B3000 has a Winbond W25N01GW and the spare size (oobsize) of it
is 64. So the maximum available ECC strength with the qpic-snand driver
is 4 but not 8.
The "nand-ecc-strength" property was not used before the commit
fc3ff2af0c ("qualcommax: allow overriding ECC strength for qpic-snand")
and calculated from the registered spare size in the Linux Kernel. As a
result, we had no issues on the GL-B3000 with the wrong ECC strength
value.
Fixes: 3307fe8ee4 ("qualcommax: ipq50xx: add support for GL.iNET GL-B3000")
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18595
Signed-off-by: Robert Marko <robimarko@gmail.com>
uImage.FIT validation was restricted to certain sub-image types
which is problematic as it then won't validate eg. 'filesystem' type
subimages. Also prevent decompressing sub-images into a arbitrary
sized buffer just to then free that buffer -- there is not need to
do this and creating malicious compressed payloads which overflow the
buffer is too easy.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Mold does not really work on MacOS, when attempting to use it for example
for ubus:
mold: get_self_path is not supportedcollect2: error: ld returned 1 exit status
Which was introduced by [1] so it seems that MacOS is not supported, so
lets make it non selectable when MacOS is the host.
[1] f9a37e9dd4
Link: https://github.com/openwrt/openwrt/pull/18575
Signed-off-by: Robert Marko <robimarko@gmail.com>
Mold supports 32 and 64 bit RISC-V, but since we only support the 64 bit
version allow using mold on it.
Link: https://github.com/openwrt/openwrt/pull/18575
Signed-off-by: Robert Marko <robimarko@gmail.com>
Mold supports 32 and 64 bit LoongArch, but since we only support the 64 bit
version allow using mold on it.
Link: https://github.com/openwrt/openwrt/pull/18575
Signed-off-by: Robert Marko <robimarko@gmail.com>
mold has seen a bunch of bugfixes and improvements since 2.33.0, so
lets update it.
Link: https://github.com/openwrt/openwrt/pull/18575
Signed-off-by: Robert Marko <robimarko@gmail.com>
In include/host-build.mk, HOST_BUILD_DIR is set by default value:
HOST_BUILD_DIR ?= $(BUILD_DIR_HOST)/$(PKG_NAME)
However the mold package has no PKG_NAME set at all. This means the
HOST_BUILD_DIR is identical to $(BUILD_DIR_HOST).
In the Host/Prepare stage, by default, the $(HOST_BUILD_DIR) will be
deleted at first unconditionally. Since HOST_BUILD_DIR is identical
to $(BUILD_DIR_HOST), the entire build_dir/toolchain-* directory will
be removed and this will cause build failure.
Adding PKG_NAME:=ld.mold can solve this issue.
Signed-off-by: Weijie Gao <hackpascal@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18567
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since the irq gets copied to sc, it's a really bad idea to use devm,
especially when probe fails.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Fixes: 4e18d22 ("mac80211: ath9k: simplify probe with devm")
Link: https://github.com/openwrt/openwrt/pull/18570
Signed-off-by: Robert Marko <robimarko@gmail.com>
Move kernel-version.mk include to proper place to properly set patch folders for test kernel.
Fixes: 8865dadea7
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Prevent accidentally including an old version of uuid.h, which causes
the build to fail because of missing definitions.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Instead of enabling RSS support, let's introduce a variant and let users
choose between both variants since it can cause network issues.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
We need both ENABLE_RSS_SUPPORT and ENABLE_MULTIPLE_TX_QUEUE in order to
support multiple RX and TX queues.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
We need both ENABLE_RSS_SUPPORT and ENABLE_MULTIPLE_TX_QUEUE in order to
support multiple RX and TX queues.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
We need both ENABLE_RSS_SUPPORT and ENABLE_MULTIPLE_TX_QUEUE in order to
support multiple RX and TX queues.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18509
[bump release, improve commit description and package changes]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Disable ASPM support for this NIC, fixing strange behavior problems, such as
increased latency, strange uneven throughput, etc.
With this option disabled the NIC achieves stable performance.
Upsteam r8169 driver disables ASPM by default for this NIC.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18509
[bump release, fix commit description, split 2nd tx queue part]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This allows the network interface naming to be stable, free from any
possible interaction from external USB network devices that might
claim usb* interface names.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This allows the network interface naming to be stable, free from any
possible interaction from external USB network devices that might
claim usb* interface names.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This allows the network interface naming to be stable, free from any
possible interaction from external USB network devices that might
claim usb* interface names.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18509
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This allows the network interface naming to be stable, free from any
possible interaction from external USB network devices that might
claim usb* interface names.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This allows the network interface naming to be stable, free from any
possible interaction from external USB network devices that might
claim usb* interface names.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Specification:
- MT7620A 580 MHz MIPS24KEc
- 64MB RAM
- 8MB SPI NOR
- MediaTek MT7612E 5.0GHz 802.11a/n/ac
- MediaTek MT7620 2.4GHz 802.11b/g/n
- 5 LEDs (white)
- 1 button
- 1 Gbit port Realtek RTL8211E GbE Phy
Serial Interface:
- 3 Pins GND, RX, TX
- Settings: 57600, 8N1
Based on support from edimax_ew-7476rpc/edimax_ew-747x
and netgear_ex3700/netgear_ex3x00_ex61xx
Notes:
- ATM there is no known way to revert to stock firmware
Flash instruction:
The only known way to flash OpenWrt image is to use tftp in U-Boot, with the
aid of a serial adapter for U-Boot console access:
1. Open the device and connect to the serial port. The device is very similar
to Edimax 7476RPC. See https://openwrt.org/toh/edimax/ew-7476rpc. No VCC!
2. Configure PC with static IP 192.168.1.2/24 and tftp server and
connect PC to device using an ethernet cable.
3. Power on the device and, on the serial console, as soon as U-Boot starts
loading, press "2" to interrupt loading.
4. Enter device ip address 192.168.1.1, PC ip address 192.168.1.2
and the firmware filename placed on the TFTP server.
5. Device will download file from server, write it to flash and reboot.
Signed-off-by: Hugo Monteiro <monteiro.hugo@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16956
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ELECOM WRC-X3000GS2 is a 2.4/5 GHz band 11ax (Wi-Fi 6) router, based on
IPQ5018.
Specification:
- SoC : Qualcomm IPQ5018
- RAM : DDR3 256 MiB (Zentel A3T2GF40CBF-HP)
- Flash : SPI-NAND 128 MiB (Macronix MX35UF1G24AD-Z4I)
- WLAN : 2.4/5 GHz 2T2R
- 2.4 GHz : Qualcomm IPQ5018 (SoC)
- 5 GHz : Qualcomm Atheros QCN6102
- Ethernet : 5x 10/100/1000 Mbps
- wan (phy) : Qualcomm IPQ5018 (SoC)
- lan (switch) : Qualcomm Atheros QCA8337
- LEDs/Keys (GPIO): 8x/3x
- UART : through-hole on PCB, 4pins near the barcode
- assignment : 3.3V, TX, RX, NC, GND from the barcode side
- settings : 115200n8
- Power : 12 VDC, 1 A (Max. 11.5W)
Flash instruction using initramfs-factory.bin image:
1. Boot WRC-X3000GS2 normally with router mode
2. Access to the WebUI ("http://192.168.2.1/") on the device and open
the firmware update page ("ファームウェア更新")
3. Select the OpenWrt factory.bin image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing
Switching to the stock firmware:
1. Load the elecom.sh script
. /lib/upgrade/elecom.sh
2. Check the current index of rootfs
bootconfig_rw_index 0:bootconfig rootfs
3. Set the index to inverted value
bootconfig_rw_index 0:bootconfig rootfs <value>
bootconfig_rw_index 0:bootconfig1 rootfs <value>
example:
- step2 returned "0":
bootconfig_rw_index 0:bootconfig rootfs 1
bootconfig_rw_index 0:bootconfig1 rootfs 1
- step2 returned "1":
bootconfig_rw_index 0:bootconfig rootfs 0
bootconfig_rw_index 0:bootconfig1 rootfs 0
4. Reboot
Partition Layout (Stock FW):
0x000000000000-0x000000080000 : "0:SBL1"
0x000000080000-0x000000100000 : "0:MIBIB"
0x000000100000-0x000000140000 : "0:BOOTCONFIG"
0x000000140000-0x000000180000 : "0:BOOTCONFIG1"
0x000000180000-0x000000280000 : "0:QSEE"
0x000000280000-0x000000380000 : "0:QSEE_1"
0x000000380000-0x0000003c0000 : "0:DEVCFG"
0x0000003c0000-0x000000400000 : "0:DEVCFG_1"
0x000000400000-0x000000440000 : "0:CDT"
0x000000440000-0x000000480000 : "0:CDT_1"
0x000000480000-0x000000500000 : "0:APPSBLENV"
0x000000500000-0x000000640000 : "0:APPSBL"
0x000000640000-0x000000780000 : "0:APPSBL_1"
0x000000780000-0x000000880000 : "0:ART"
0x000000880000-0x000000900000 : "0:TRAINING"
0x000000900000-0x000003c40000 : "rootfs"
0x000003c40000-0x000003fc0000 : "Config"
0x000003fc0000-0x000007300000 : "rootfs_1"
0x000007300000-0x000007680000 : "Config_2"
0x000007680000-0x000007b80000 : "Reserved"
0x000007b80000-0x000007c00000 : "FWHEADER"
0x000007c00000-0x000007c80000 : "Factory"
Known Issues:
- All Wi-Fi related peripherals are disabled.
This device has only 256 MiB RAM and it's too few for ath11k. To
prevent OOM when using LuCI or other softwares, disable Wi-Fi related
peripherals in device tree at the moment.
- This device has a Macronix MX35UF1G24AD SPI-NAND chip registered as
oobsize=128 in Linux Kernel. But using BCH8 breaks I/O on the chip
with the following errors, so this support uses BCH4 instead.
root@OpenWrt:~# strings /dev/mtdblock10
[26427.133154] mtdblock: MTD device '0:appsblenv' is NAND, please consider using UBI block devices instead.
[26427.134125] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 2
[26427.142240] I/O error, dev mtdblock10, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 2
[26427.151427] I/O error, dev mtdblock10, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 2
[26427.160440] I/O error, dev mtdblock10, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
[26427.169619] I/O error, dev mtdblock10, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[26427.178083] Buffer I/O error on dev mtdblock10, logical block 0, async page read
Notes:
- This device has dual-boot feature and it's managed by the index in the
0:bootconfig and 0:bootconfig1 partitions.
MAC Addresses:
LAN : 38:97:A4:xx:xx:60 (0:APPSBLENV, "eth1addr"/"ethaddr" (text))
WAN : 38:97:A4:xx:xx:63 (0:APPSBLENV, "eth0addr" (text))
2.4 GHz: 38:97:A4:xx:xx:61 (0:APPSBLENV, "wifi0" (text))
5 GHz : 38:97:A4:xx:xx:62 (0:APPSBLENV, "wifi1" (text))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18543
Signed-off-by: Robert Marko <robimarko@gmail.com>
Make the ECC strength in the qpic-snand driver configurable via device
tree to use the device-specific ECC strength value.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18543
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for ELECOM WRC-X3000GS2 to update "bootdelay" variable
configured as "0" by default when sysupgrade.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18543
Signed-off-by: Robert Marko <robimarko@gmail.com>
To further improve cleanup and maintenance usage, move the kernel
version files to target/linux/generic directory. This permits to self
contain any change to the specific generic directory instead of having
to bload the include directory of periodic changes.
In kernel-version.mk we now use GENERIC_PLATFORM_DIR provided by
target.mk. To make this work, we need to move the inclusion of
kernel-version.mk in target.mk right after GENERIC_PLATFORM_DIR is
defined.
This also comes to permit downstream project to provide a custom generic
directory and specify the kernel version complete of the hash and the
minor version without having to affect other feeds.
In such case both generic and the target directory are provided as feeds
and OpenWrt reference these specific one instead of the generic one.
For downstream it's still suggested and preferable to all match the
shipped generic kernel minor version but this change permits to at least
enforce good practice instead of having to bloat OpenWrt include file of
all kind of downstream changes (making porting to OpenWrt mainline even
more difficult)
Link: https://github.com/openwrt/openwrt/pull/18537
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Changes: https://github.com/u-boot/u-boot/compare/v2025.01...v2025.04
Drop patch 100-rockchip-add-FriendlyElec-NanoPi-R3S.patch. U-Boot
upstream now supports this board.
Tested on Radxa ROCK 5B+.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The TP-link Deco X80-5G is a AX WIFI router with a single 1G (LAN) and 1 2.5G (WAN) port with a built in Quectel 5G modem.
Specifications:
Architecture ARMv8-A (aarch64 Cortex A53, 4 cores)
Vendor Qualcomm
Bootloader U-Boot (2016)
System-On-Chip Qualcomm IPQ8074A (Networking Pro 1210 platform)
CPU/Speed 2.2GHZ
Flash-Chip ESMT F59D1G81MB-45TI 1G-bit NAND
Flash MB 128MB (1Gbit)
RAM-chip 2* ESMT M15T4G16256A-DEBG2G 2Gb DDR3L (32bit)
RAM MB 512MB (4Gbit)
WLan System-On-Chip (5g) Qualcomm QCN5054
WLan Front end modules (5g) 8* Qorvo QPF4588
WLAN (5G) A/N/AC/AX
WLAN Antenna (int) 8* (4 shared with 2.5G)
WLan System-On-Chip (2.4G) Qualcomm QCN5024
WLan Front end modules (2.4G) 4* Skyworks SKY85340-11
WLAN (2.4G) B/G/N/AX
WLAN Antenna (int) 4* (shared with 5g)
Eithernet-phy (1Gbit) Qualcomm (Atheros) AR8033-AL1A
Ethernet (1Gbit) 1*
Eithernet-phy (2.5Gbit) Qualcomm QCA8081
Ethernet (2.5Gbit) 1*
Switch Embedded in the SOC?
Serial 1.8v 8n1 (testpoints)
Modem System-On-Chip Qualcomm 5G RG50xQ (Snapdragon X55 platform)
5G modem capability 5000Mbps down 900Mbps up
5G modem bands N1/N3/N5/N7/N8/N20/N28/N38/N40/N41/N77/N78/N79
4G modem capability 4.5G LTE-Advanced Pro (Cat20 down 2Gbps) (Cat18 up 200Mbps)
4G modem FDD bands B1/B3/B5/B7/B8/B18/B19/B20/B26/B28
4G modem TDD bands B34/B38/B39/B40/B41/B42/B43
Modem antenna (int) 8* (5G/4G use)
Modem antenna (ext) 2* SMA connectors (5G/4G use)
SIM type 1* Nano SIM
Telephony 1* POTS RJ11
(see wiki for more info:)
https://openwrt.org/inbox/toh/tp-link/x80-5g_v1
Notes:
Installation Instructions:
Between antennas 7 and 8 on the PCB with the RGB harness there are three test pads labelled TP1 TP2 and TP3 connections are as follows:
|TP2|-- RX
|TP1|-- TX
|TP3|-- GND
RX requires an external pullup to operate somewhere around 5 K ohm but your luck may vary the Uart is 1.8v
Set a static IP and set up a tftpserver and terminal.
power the router and quickly type the magic string “tpl” and press enter to break into u-boot
in the shell set the environment variables to enable tftp booting
setenv ipaddr (routerIP)
setenv serverip (server IP)
load you initramfs:
tftpboot 0x44000000 (serverIP):openwrt-qualcommax-ipq807x-tplink_x80-5g-initramfs-uImage.itb
boot your initramfs
bootm
upload your factory image to /tmp
format and install the factory image:
ubiformat /dev/mtd12 -y -f /tmp/openwrt-qualcommax-ipq807x-tplink_x80-5g-squashfs-factory.ubi
Note as this device swaps root partitions upon update your boot partition may be set as mtd13
Update script to mount factory tplink partition's for MAC recovery and device data.
Capture Labelmac from Factory_data partition.
Patch LAN from Labelmac.
Patch ART from Labelmac.
Set GPIO to make modem operational from boot.
GPIO fan tables work like the stock device with three fan maps high active idle with a top fan speed of 6800 RPM.
High temp 70 deg speeds 6-8
Active temp 50 deg speeds 2-5
low temp 25 degree speed 0-1
Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/16329
Signed-off-by: Robert Marko <robimarko@gmail.com>
Patch script used for mounting of factory data partitions to not assume devices names or use hardcoded identifiers.
Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/16329
Signed-off-by: Robert Marko <robimarko@gmail.com>
5.8.1 (2025-04-03)
* Multithreaded .xz decoder (lzma_stream_decoder_mt()):
- Fix a bug that could at least result in a crash with
invalid input. (CVE-2025-31115)
- Fix a performance bug: Only one thread was used if the whole
input file was provided at once to lzma_code(), the output
buffer was big enough, timeout was disabled, and LZMA_FINISH
was used. There are no bug reports about this, thus it's
possible that no real-world application was affected.
* Avoid <stdalign.h> even with C11/C17 compilers. This fixes the
build with Oracle Developer Studio 12.6 on Solaris 10 when the
compiler is in C11 mode (the header doesn't exist).
* Autotools: Restore compatibility with GNU make versions older
than 4.0 by creating the package using GNU gettext 0.23.1
infrastructure instead of 0.24.
* Update Croatian translation.
Link: https://github.com/openwrt/openwrt/pull/18558
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch backport a fix for the SD card detection on NanoPi R6c/R6S
from upstream commit 95147bb42b
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18553
Signed-off-by: Robert Marko <robimarko@gmail.com>
rootfs_size was being set after the bootscript was already copied
to KDIR_TMP/ this was sneaky because it only affected the initial
compile. All subsequent compiles the rootfs_size is correct before
the copy is made and the bug goes un discovered. Hence the reason I
missed it during testing.
this patch fixes the issue and also refactors the
make recipe to update rootfs_size after the copy
is made, and updates the copy exclusively.
Fixes: 3307fe8ee4 ("qualcommax: ipq50xx: add support for GL.iNET GL-B3000")
Signed-off-by: Scott Mercer <TheRootEd24@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18556
Signed-off-by: Robert Marko <robimarko@gmail.com>
drop upstream patches
$ git log --no-merges --oneline v2.7.6..v2.8
48ceda8 Version 2.8
b3d0c93 Regression in commit abe92e8010ab affecting MariaDB tests
29fced6 Count traditional diff pattern lines correctly
b5d2124 patch: fix --no-backup-if-mismatch regression
86ac7e2 Fix dodgy assert with side-effects in insert_cached_dirfd
7d87652 Declare an expected test failure on Haiku.
86baf97 build: update gnulib submodule to latest
1ba2c1b Fix two test failures on Haiku.
1da6bf8 Check for newlines only when creating a file name
30ee610 Gnulib renamed some modules
6dbc381 maint: update bootstrap from gnulib
05ac924 build: update gnulib submodule to latest
95e0092 maint: make update-copyright
5bac274 Set --no-backup-if-mismatch when in --posix mode
910fecf Add missing feature tests to the test suite
be8b3c6 Disable release-prep
c61485b Fix "make release" to handle alpha releases
499916f Add announce-gen module for "make release"
adb1ebc Pacify gcc -fsanitize=address
6bdae94 Fix memory leak when malformed unidiff patch
72a146c Port to clang address sanitizer
e2e6820 Refactor argc+argv processing
606c091 Omit needless get_some_switches code
ee3cc40 Revert "Remove obsolete require_gnu_diff function"
8cae4fc Remove obsolete require_gnu_diff function
164b529 savebuf can return a null pointer
91c1e4f Spelling fixes
a03e1ba Port other reject-format test to non-GNU diff
9ba5eb0 Don’t be fooled by NUL bytes in diff directives
79dd5e7 Don’t be fooled by "\000" in file name
8492a6a Port to quasi-GNU diff
f6f2c6f In previous patch, make w_q static
0525681 Pacify -Wunterminated-string-initialization
301411d Spelling fixes
4615206 Remove double semicolon
923e0ef Prefer angle bracket headers
5d17ca0 Update more old copyright notices
5f4edd3 Simplify memory allocation of files to delete
802511c Report patch read errors more immediately
a93b50d Port fflush usage to OpenBSD 7.5
55e224b Update old copyright notices
33a7fd8 Fix gl_gcc_warnings typo in ‘configure’
2313b37 build: update gnulib submodule to latest
37fec39 Remove some dependencies no longer needed
cc87173 Update NEWS as per recent changes
7887622 Update POSIX citations
18f4dd6 Use “Gruenbacher” in international contexts
638675c Adjust libs to match recent Gnulib
53400a1 Pacify clang -Wbitwise-conditional-parentheses
e8e1bcb Remove “support” for nested critical sections
b963510 Simplify critical section code in util fns
85949fb Shrink critical sections
448ff9b Defer signals by hand with sigatomic_t
b95a603 output_file_later avoid a malloc+free pair
2663228 Defend against closed stdin/stdout/stderr
fc77964 Stop using Gnulib ‘execute’ module
470699c Move defer_signals up
f696e4e Make sigs, NUM_SIGS local
4d3a4ab Rename block_signals
b3bb925 Trade a bit of space for time in parse_c_string
070d859 Allocate first patchbuf statically
f46a90f Use bigger buffer size by default
2e64cfd Preinitialize fatal_act.sa_hander
45de0d9 Prefer EXIT_SUCCESS etc. to literal integers
82c4940 Fix some signal handling races
eceea61 Fix --set-utc TZ setting
9c55d3f Improve logic for when rename removes source
61c72f0 Fix signal race when renaming file
705c9bc Simplify traverse_another_path via last_component
77f21a6 Stop using Gnulib dirname module
fe8ffd9 Fix implausible overflow when reading symlinks
5e84bda Access checks should use effective, not real
8d4ca49 Don’t assume AT_FDCWD != -1
fe5d4a0 Copy input to output attributes via fd if possible
ca4c431 Simplify timestamp epoch checking
0ad4347 Check for ftello failures
c49a16d Remove format_linenum
22efdee Fix "with multiple words" line number
5a70a1b Drop Plan B
c0d465f Prefer ximemdup0 to xmemdup0
b91aab2 Refactor ifetch API
55c8a5c Do not attempt huge I/Os
e0e121e Use outfd when setting file attributes
241e57e Don’t assume Linux-like S_IFREG
0f8c628 Use STDOUT_FILENO etc
f2c3676 Fix unlikely glitch with ed diffs
cec6407 Use fds to copy attrs in create_backup_copy
6b7b01b Be more careful about (time_t) -1
0433553 X == -1 → X < 0
0a66dee Let set_file_attributes use fds not names
36ff2c9 Port to narrow unsigned uid_t
3951496 Check for output errors more systematically
6429630 Report input error right away
03cb187 Simplify EOF testing
cc7cde7 Prefer other types to ‘int’
4c6650b Detect unlikely integer overflow in size calcs
abe92e8 Prefer idx_t, ptrdiff_t to lin
30449e2 Fix compatibility issue with blanks in patches
9228a8c pch_swap return type cleanup
c1c438d Fix unlikely int overflow in hunk counts
5d3f41f Use char for char in plan_a
fb056f2 Cache cwd_is_root dev, ino
84b5f34 Avoid ‘unsigned’ in safe.c
d2e113e Simplify get_sha1
f73718b Avoid casts in patch.c
79eef3e Prefer idx_t in util.c
11588d0 Prefer idx_t in pch.c
e16037d Prefer idx_t in patch.c
388926f Prefer idx_t in list.h
3582fdb Prefer idx_t in inp.c
4a47c00 build: update gnulib submodule to latest
4f8c4b8 Don’t limit strip counts etc. to INT_MAX
0a810b6 Fix unlikely integer overflows in patch.c
bac3b6d Fix unlikely integer overflows in pch.c
8fb784b Fix unlikely integer overflows in inp.c
e10f3ca Promote minmax.h to common.h
57e2165 Avoid some memory allocation by not using ‘const’
eb18b39 Remove unnecessary char * casts in inp.c
d60cb72 Pacify gcc -Wunused-parameter when !USE_XATTR
05ef886 Pacify gcc -Wunused-parameter when !USE_XATTR
1f8d192 maint: stop using alloca
ba92722 Don’t assume O_RDONLY == 0
0f98e03 Avoid syscall when nested signal block
1235ccc Add signal comment
43ee674 build: update gnulib submodule to latest
e381947 Update NEWS, README-prereq
2c2a83b Omit _Noreturn when easy
a13c2ea Replace __attribute__ with attribute.h
6eb2d13 Switch from ctype.h to c-ctype.h
d1a6847 Simplify warning configuration
d6631b3 Prefer ATTRIBUTE_* to _GL_ATTRIBUTE_*
bc6899d Pacify gcc -Wno-unused-parameter
da25985 Improve ‘git diff’ output if desired
248ef13 Prefer strerror to perror
6cb321a A bit more long-string fixing
47bc09d Prefer nullptr to NULL
7608746 More fixing of printing of very long strings
323da0d Don’t assume string sizes fit in int when printing
53d1014 Avoid fprintf INT_MAX overflow when merging
59681c8 Avoid sprintf INT_MAX overflow
4278b91 Reject output file names containing '\n'
34b45bc Update man page a bit.
d18c05d Update copyright notices
af828e5 Fix some races involving signals
b3a6c95 Don’t attempt to remove files we didn’t create
9abc949 Omit goto in try_safe_open
90e62d5 Pacify clang re obsolete O_CREAT test
2b87c1e Allow nested block/unblock of signals
7aa1c3b Adjust to new Gnulib bootstrap post imports
99c0c0b maint: remove generated file lib/Makefile.am
1c087d6 Rely on Gnulib inttypes module
7214f8d Update main locals more consistently
6785b2c Use struct outfile * in function args
72d7ed0 Refactor temp names into struct
abf6fb1 Simplify by using Gnulib sigaction
d3816ac Avoid unnecessary freeing in output_files
346d3ac Clean up cleanup
ff2317b Port better to GNU/Hurd
c2d9792 Don’t say empty backups are unreadable
8c27a03 Spelling fixes
d46d729 Change manywarnings usage to be more like coreutils
924698b Pacify clang, which dislikes n + "y"
8939519 Pacify -Wstrict-overflow in pch.c
531cc2b Pacify -Wsuggest-attribute=format in util.c
ff13fea Port to non-VLA C compilers
3d5c0d1 Rename vars to pacify gcc -Wshadow
56788ce Stop including stdbool.h
c10da77 Recommend 64-bit time_t on 32-bit platforms
1e21767 Remove pch_sha1
39005cf Move skip_spaces
755712d Remove pch_timestamp function
04f0eeb Prefer extern inline to static inline for list.h
f06c123 maint: pacify gcc 14 -Wcast-align
aab6e7b maint: pacify -Wanalyzer-null-argument
d1d32c9 maint: work around GCC bug 109839
7575694 maint: pacify gcc -Wmissing-variable-declarations
8f78b09 maint: pacify gcc -Winline
bb841fd maint: port _FORTIFY_SOURCE to Ubuntu
4887683 maint: assume STDC_HEADERS
5b8ecde maint: spruce up our .m4 files a bit
009a424 maint: omit obsolete macro calls
299167f maint: simplify .gitignore
3ec44a4 build: update gnulib submodule to latest
68cb529 build: update gnulib submodule to latest
f144b35 build: Enable the 'subdir-objects' Automake option.
faafc79 build: update gnulib submodule to latest
c835ecc Pass the correct stat to backup files
24f81be maint: modernize README-{hacking,prereq}
7623b2d Fix test for presence of BASH_LINENO[0]
0993940 gnulib: update to latest
78ed9de Add missing-section tests to context-format test case
76e7758 Fix failed assertion 'outstate->after_newline'
15b158d Avoid invalid memory access in context format diffs
dce4683 Don't follow symlinks unless --follow-symlinks is given
61d7788 Don't crash when RLIMIT_NOFILE is set to RLIM_INFINITY
b7b028a Abort when cleaning up fails
a5b442c Skip "ed" test when the ed utility is not installed
2b584ae Improve support for memory leak detection
9c98635 Fix swapping fake lines in pch_swap
ff81775 Make the (debug & 2) output more useful
369dccc Don't leak temporary file on failed multi-file ed-style patch
1959988 Don't leak temporary file on failed ed-style patch
f322a7e Request 'alloca' module from gnulib.
458ac51 Fix 'ed-style' test failure.
1e9104c Fix check of return value of fwrite().
ae81be0 maint: avoid warnings from GCC8
2a32bf0 Minor cleanups in do_ed_script
ff1d3a6 Use gnulib execute module
3fcd042 Invoke ed directly instead of using the shell
123eaff Fix arbitrary command execution in ed-style patches (CVE-2018-1000156)
b5a91a0 Allow input files to be missing for ed-style patches
f290f48 Fix segfault with mangled rename patch
074e239 Test suite: fix Korn shell incompatibility
f6bc5b1 Test suite compatibility fixes
3bbebbb Avoid set_file_attributes sign conversion warnings
Signed-off-by: Russell Senior <russell@personaltelco.net>
Link: https://github.com/openwrt/openwrt/pull/18479
Signed-off-by: Robert Marko <robimarko@gmail.com>
