Add WED related nodes to the device tree of the MT7988 SoC family.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import patches from kernel 6.13:
- net: dsa: realtek: Use for_each_child_of_node_scoped()
- net: dsa: realtek: rtl8365mb: Make use of irq_get_trigger_type()
- net: dsa: realtek: rtl8366rb: Make use of irq_get_trigger_type()
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/19381
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The interrupt handler reads from the mailbox if no other reason for the
interrupt is known. If a spurious interrupt is received just after a
mailbox message has been sent, this means that the response to the
previous message is read again and returned by DSL_BSP_SendCMV instead
of the actual response.
To fix this, check the status register before reading from the mailbox
in the interrupt handler.
Tested on Fritzbox 7320. Without this change, there is occasionally a
kernel panic due to an out-of-bounds memory access in the ltq-adsl
driver (in DSL_DRV_DEV_G997_SnrAllocationNscGet), as a result of an
incorrect value returned by DSL_DRV_DANUBE_CmvRead. This is reproducible
by calling "dsl_cpe_pipe.sh g997dsnrg 1 1" multiple times.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/19385
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Building perf on mips/malta fails on intel-pt-decoder due to a header issue
previously seen in f434643857 ("perf: fix build on PowerPC"):
In file included from util/intel-pt-decoder/intel-pt-insn-decoder.c:12:
util/intel-pt-decoder/../../../arch/x86/include/asm/insn.h: In function 'insn_field_set':
util/intel-pt-decoder/../../../arch/x86/include/asm/insn.h:56:21: error: implicit declaration of function '__cpu_to_le32'; did you mean 'cpu_to_le32'? [-Wimplicit-function-declaration]
56 | p->little = __cpu_to_le32(v);
| ^~~~~~~~~~~~~
| cpu_to_le32
util/intel-pt-decoder/../../../arch/x86/include/asm/insn.h: In function 'insn_set_byte':
util/intel-pt-decoder/../../../arch/x86/include/asm/insn.h:64:20: error: implicit declaration of function '__le32_to_cpu'; did you mean 'le32_to_cpu'? [-Wimplicit-function-declaration]
64 | p->value = __le32_to_cpu(p->little);
| ^~~~~~~~~~~~~
| le32_to_cpu
Extend the previous powerpc fix to mips, disabling intel-pt-decoder build.
cc: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/19426
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Package driver modules for I2C HID devices such as touchpads,
touchscreens and trackpoints found on some laptops. Only the ACPI
firmware variant of the driver is packaged for now as that's what I got
for testing.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add driver packages for Intel Low-Power Subsystem devices which are part
of some Intel chipsets. They are mainly needed to have access to the I2C
bus used for HID devices.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The current offset used for extracting QCN6122 calibration data
is incorrect on the Yuncore AX830. This patch corrects the
offset to ensure proper WiFi initialization.
Tested on: Yuncore AX830
Signed-off-by: Shubham Vishwakarma <shubhamvis98@fossfrog.in>
Link: https://github.com/openwrt/openwrt/pull/19416
Signed-off-by: Robert Marko <robimarko@gmail.com>
Support for 6.12 is ready; add it as a testing kernel.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19069
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Most of them were manually refreshed.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19069
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
No need to keep it in kernel specified folder anymore.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19069
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The script always gets passed the package name, not the source name.
Optimize for the default case where the package name matches the
filename prefix.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Many x86 machines can boot from SD cards, and some embedded x86 devices
come with an eMMC. Include drivers for all common MMC/SDHCI controllers
to allow booting from SD/MMC on x86.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Directly call the function "get_linux_version()" to get the integer
kernel version number.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19172
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
A new function "get_linux_version()" to normalize and print the
kernel version as an integer. In some migration scripts, it is
useful for checking the Linux kernel version.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19172
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently, if OEM recovery flashes OpenWrt to second ubi1,
OpenWrt cannot boot. With this commit, recovery image is built
with initramfs kernel, so that it can boot from either ubi or ubi1.
This adds an extra step to OpenWrt installation from OEM:
user needs to sysupgrade from initramfs to full system.
Signed-off-by: Mateusz Krzak <kszaquitto+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18878
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The number of serial interfaces for the chip 8250 can be configured at
build time. This is currently not configurable and is always set to 16
interfaces. This is too little for some small embedded devices and too much
for others (x86_64). Therefore, this commit creates the possibility to set
this at compile time.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/19217
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Host default environment doesn't provide/require gnutls headers needed
for building mkeficapsule tools, and as tegra target doesn't require EFI
capability, disable the build of mentioned tool.
Fixes: 92cd360aac ("uboot-tegra: bump version to 2025.04")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250713125126.215092-1-tmn505@terefe.re/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
8mA driving will cause overshoot issue on SPI NAND. Change it to 4mA.
- Reference:
003744197a
On Linux mainline (mt7986.dtsi), spi's source clock is: clocks = <&topckgen CLK_TOP_MPLL_D2>, which is
208MHz. Usable clock division will be:
- 208/4=52MHz
- 208/6~=35MHz
- 208/8=26MHz
and so on
If we specify 50MHz for spi-max-frequency, it will actually run under about 35MHz. Most SPI NAND & NOR
flashes are capable of running with more than 52MHz, include Micorn MT29F4G01ABAFDWB on ZyXEL EX5601.
[Ref: #18752] To reach highest performance on mt7986, use spi-max-frequency = <520000000>. Basically,
this setting should work on all mt7986 PCBs since most mt7986 boards follow reference design. However,
other boards needs further test to guarantee stability.
Signed-off-by: Sky Huang <SkyLake.Huang@mediatek.com>
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/18813
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add new option to bootmenu which allows to boot the system from USB.
You can use dd to prepare USB with initramfs:
- dd bs=1M if=openwrt-mediatek-filogic-zyxel_ex5601-t0-ubootmod-initramfs-factory.ubi of=/dev/sdX
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18949
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In rtl931x_led_init, the number of leds per port is not properly set. It
currently uses a hardcoded value of 1 which seems to be taken initially
from a specific device. This hardcoded value assumes any port always has
exactly two leds.
The RTL930x variant - rtl930x_led_init - does a better job at this. So
take it and use it for RTL931x too with the corresponding register.
While at it, rename the function to a proper naming scheme.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19241
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use common function ubootenv_add_mmc
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19269
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The direction needs to be included in the IOCTL call.
Fixes: b91d7d9d78 ("ltq-*-app: extend ubus metrics/statistics")
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/19363
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These cpu erratums are used by other SoCs, just remove them.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/19380
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These cpu erratums are used by other SoCs, just remove them.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/19380
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move the following kernel symbol configs to generic:
COMPRESSED_INSTALL and IMX_SCMI related configs
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/19380
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Dell/SonicWall APL27-0B1 (marketed as SonicPoint ACi) is a dual band
wireless access point. Very similar to already supported APL26-0AE,
which all antennas are external, while this variant has internal
antennas. End of life as of 2022-07-31.
Specification
SoC: QualcommAtheros QCA9550
RAM: 256 MB DDR2
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9890 oversized Mini PCIe card
Ethernet: 2x 10/100/1000 Mbps QCA8334
port labeled lan1 is PoE capable (802.3at)
USB: 1x 2.0
LEDs: LEDs: 6x which 5 are GPIO controlled and two of them are dual color
Buttons: 1x GPIO controlled
Serial: RJ-45 port, SonicWall pinout
baud: 115200, parity: none, flow control: none
Before flashing, be sure to have a copy of factory firmware, in case You
wish to revert to original firmware.
Installation
1. Prepare TFTP server with OpenWrt sysupgrade image and rename that
image to "ap135.bin".
2. Connect to one of LAN ports.
3. Connect to serial port.
4. Hold the reset button (small through hole on side of the unit),
power on the device and when prompted to stop autoboot, hit any key.
The held button can now be released.
5. Alter U-Boot environment with following commands:
setenv bootcmd bootm 0x9F110000
saveenv
6. Adjust "ipaddr" (access point, default is 192.168.1.1) and "serverip"
(TFTP server, default is 192.168.1.10) addresses in U-Boot
environment, then run following commands:
tftp 0x80060000 ap135.bin
erase 0x9F110000 +0x1EF0000
cp.b 0x80060000 0x9F110000 $filesize
7. After successful flashing, execute:
boot
8. The access point will boot to OpenWrt. Wait few minutes, until the
wrench LED will stop blinking, then it's ready for configuration.
Notes
By default no power is provided on USB port, so attached USB devices
won't enumerate. To change that enable regulator with:
echo "enabled" > /sys/devices/platform/output-usb-vbus/state
To disable power write "disabled" to the same file.
Ther regulator state will reset on reboot, consider running this command
on hotplug event or add it to /etc/rc.local. The hotplug event should
look like this:
if [ "${PRODUCT}" = "1d6b/2/606" ] && [ "${ACTION}" = "add" ]; then
echo "enabled" > /sys/devices/platform/output-usb-vbus/state
fi
Place it in /etc/hotplug.d/usb/10-usb-power.
Known issues
Initramfs image can't be bigger than specified kernel size, otherwise
bootloader will throw LZMA decompressing error. Switching to lzma-loader
should workaround that.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250529202033.28250-2-tmn505@terefe.re/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Allows to enable/disable attached regulators from userspace, i.e. by
simply writing value to a sysfs exported state file. Useful in case of
USB port VBUS toggled by GPIO.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250529202033.28250-1-tmn505@terefe.re/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Unfortunately they still apear with prolonged serial console usage.
While it's not common to use serial console past initial setup, alas
when the condition is hit the console is almost unusable.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250618170045.473711-2-tmn505@terefe.re/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
