Add backport patch that fixes ath12k regdomain parsing failure in
6GHz band triggered by the latest regdb/board-2.bin update.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18512
Signed-off-by: Robert Marko <robimarko@gmail.com>
Previous commits missed some refreshing
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18512
Signed-off-by: Robert Marko <robimarko@gmail.com>
The submenu of two diag modules is missing, fix it.
Fixes: 65de1e0 ("kernel: add missing symbols for lxc")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/18480
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, bcm63xx-cfe is being installed into kernel build dir, however
that does not work for Image Builder as only certain artifacts from kernel
build dir are included in Image Builder.
So, simply install bcm63xx-cfe into image staging dir so its artifacts can
be used in Image Builder as well.
Fixes: #18408Fixes: #18409
Link: https://github.com/openwrt/openwrt/pull/18463
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add patches to enable QCN9274 radios that support both 5GHz and 6GHz
bands.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In board-2.bin available at linux-firmare regdb is stored with
board-id=255. This change is needed to properly use it.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Partially revert removal of 003 patch to fix compilation error with
kernel 6.6.
In 6.6 .remove still require int and .remove_new needs to be used.
Fixes: bfb106e8ae ("mac80211: backport API change for sta rate control update")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add qualcommbe to the supported target of dwc3-qcom kernel module. USB3
is correctly supported on IPQ95xx and can be enabled.
Link: https://github.com/openwrt/openwrt/pull/17788
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
ath9k uses a deprecated GPIO API that assumes a starting base of 0. This
is no longer the case and so must be fixed.
Upstream pending patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is only used by mach files, which are no longer used in OpenWrt.
Allows removing a custon ath9k_platform.h file.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
These only work with and are useful with mach files. Now that those are
gone, this can go too.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
Simplify patch with gpiochip_add_data, struct reduction, new GPIO API,
and header cleanup.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath10k dt-binding property "qcom,coexist-support" was
explicitly defined as type uint8 since upstream commit
ed09c61eb19d ("dt-bindings: net: Convert ath10k to YAML").
Therefore, this hack patch no longer makes sense.
Link: ed09c61eb1
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18393
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport two commits to resolve issues with ath1kk causing it to fail
driver registration on iommuless systems with DRAM outside of 32bit
addressing such as a 4GiB imx8mm:
commit 1bcd20981834 ("wifi: ath11k: Fix DMA buffer allocation
to resolve SWIOTLB issues")
commit eeadc6baf8b3 ("wifi: ath11k: Use dma_alloc_noncoherent
for rx_tid buffer allocation")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/17751
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit 1375a7bae0.
This version does not activate the CONFIG_LEDS_CLASS_MULTICOLOR option,
this option is controlled by the generic target configuration.
Signed-off-by: jonathan brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/17277
[Reword commit message]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This new version fixes some memory leak and NULL pointer issues.
Upstreamed patches:
[1] 010-api_update.patch
[2] 201-wifi-ath10k-add-LED-and-GPIO-controlling-support-for.patch
The new 003 patch was introduced to fix the build error on old LTS
kernel. The patch 004 was used to fix the issue of IPQ4019 radio
not being able to start.
Tested on QCA9882 and IPQ4019.
[1] bca8bc0399
[2] 8e1debd824
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18368
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove settings and depends that are not used anywhere.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18291
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix compilation error for old stable version caused by
genlmsg_multicast_allns backport fix pushed middle version.
Version 5.15 version 0-169, 6.1 version 0-115, 6.6 version 0-58 have the
old genlmsg_multicast_allns version with flags variable.
Compiling backport project with these version result in a compilation
error. To handle this, introduce a backport function for the affected
kernel version.
Link: https://github.com/openwrt/openwrt/pull/18373
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
MR7500 features IPQ6018 which is CPPE, however, it also utilizes AQR114CB0 as WAN.
Previously, without this patch, aquantia_phy_api_ops was never called.
Therefore, enable `IN_AQUATIA_PHY` so that AQR PHY gets initialized properly on boot.
[ 3.973942] Aquantia AQR114C 90000.mdio-1:08: loading firmware version 'v5.6.5 Cybertan Divo 090221 14:43:44' from 'NVMEM'
[ 16.059953] aquantia_phy_api_ops_init[1485]:INFO:qca probe aquantia phy driver succeeded!
[ 17.930149] Aquantia AQR114C 90000.mdio-1:08: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:08, irq=POLL)
Signed-off-by: Weikai Kong <priv@pppig236.com>
Link: https://github.com/openwrt/openwrt/pull/18185
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for the Intel E800 series of cards, with switchdev
support enabled for lower CPU usage.
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
Link: https://github.com/openwrt/openwrt/pull/17564
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Sets the boot flag for the i40e network device driver
to load it at a more early stage of the boot process.
With commit 0a47d518df,
I added a boot priority for the mlx4 and mlx5 drivers.
Also, increase those priorities because I think they
are too low since there is currently no "room" for
built-in network device drivers.
That can cause interface order, i.e., name inconsistencies,
when Mellanox ConnectX cards are inserted or removed.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/17990
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CONFIG_NET_SWITCHDEV option is needed by CONFIG_DSA and some other
options. It is boolean, we have to compile it into the kernel it self.
Activate it for all targets in the generic configuration, it is already
activated for most of them. This allows to install DSA drivers as a
module.
On the ramips/mt7620 target the kernel would grown by 4.5kB.
For some small targets which do not support a DSA switch by default the
option is deactivated.
Link: https://github.com/openwrt/openwrt/pull/17668
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This allows the network interface naming to be stable, free from any
possible interaction from external USB network devices that might
claim usb* interface names.
(This was a real problem I encountered with a nanopi R6S device and
an external rtl8152 usb3 network controller - the USB controller would
claim the eth1 name, causing much confusion).
Signed-off-by: Michel Lespinasse <michel@lespinasse.org>
Link: https://github.com/openwrt/openwrt/pull/17638
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It doesn't depend on either usb-net or usb-net-cdc-ncm. It does, however, depend
on mii. Fix thusly, and make it depend explicitly on usb, not usb-net.
While at it, add a conditional dependency on libphy, for future kernel versions.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Now that CONFIG_USB_NET_DRIVERS is unconditionally enabled, remove it from the
usb-net kconfig symbol list.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
The kmod-mlxsw-spectrum driver activated CONFIG_DCB indirectly already
on all targets which are building this driver. All other DCB capable
driver did not activate their DCB support.
CONFIG_DCB increases the uncompressed kernel size by about 7.8KB.
CONFIG_DCB is only needed some data center Ethernet cards and not used
on normal routers. Activate it only on the x86_64 and the armsr_arm64
target which are used on normal servers or in VMs.
Link: https://github.com/openwrt/openwrt/pull/17672
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
btmtk.ko is used by btusb.ko and btmtkuart.ko, add it into an own
package and make both packages depend on it.
Fixes: 1c42a0be36 ("kernel: modules: bluetooth: separating UART and USB drivers")
Link: https://github.com/openwrt/openwrt/pull/18110
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There is some new changes since 12.5.r2 to 12.5.5, so refresh
and update patches.
Changes:
modified: package/kernel/qca-nss-dp/Makefile
modified: package/kernel/qca-nss-dp/patches/0006-nss_dp_main-Use-a-phy-handle-property-to-connect-to-.patch
modified: package/kernel/qca-nss-dp/patches/0008-nss-dp-allow-setting-netdev-name-from-DTS.patch
deleted: package/kernel/qca-nss-dp/patches/0011-01-edma_v1-rework-hw_reset-logic-to-permit-rmmod-and-in.patch
deleted: package/kernel/qca-nss-dp/patches/0011-02-nss_dp_switchdev-correctly-unregister-notifier-on-dp.patch
deleted: package/kernel/qca-nss-dp/patches/0011-03-nss_dp_main-swap-dp_exit-function-call.patch
deleted: package/kernel/qca-nss-dp/patches/0011-04-nss_dp_main-call-unregister_netdev-first-in-dp_remov.patch
deleted: package/kernel/qca-nss-dp/patches/0011-05-nss_dp_main-use-phy_detach-instead-of-disconnect-in-.patch
deleted: package/kernel/qca-nss-dp/patches/0011-06-edma_v1-skip-edma_disable_port-in-edma_cleanup-subse.patch
Log:
2024-10-16 |4c9f671| [qca-nss-dp] removed the calling of fal_port_autoneg_status_get
2024-10-16 |fb33119| Merge "[qca-nss-dp] Change Debug Level of TX Complete Errors"
2024-10-15 |e197b9d| [qca-nss-dp] Change Debug Level of TX Complete Errors
2024-10-03 |1b7aeb1| Merge remote-tracking branch origin/AU_LINUX_QSDK_GINGER_OPEN_TARGET_ALL.12.5.5.230.918 into HEAD
2024-10-01 |830ac73| Merge "[qca-nss-dp] Enable rmmod support for qca-nss-dp module."
2024-06-05 |aef242d| [qca-nss-dp] Enable rmmod support for qca-nss-dp module.
2024-09-18 |b1bfeb6| Merge "[qca-nss-dp] Move pr_info to pr_debug"
2024-09-12 |54aee26| Merge "[qca-nss-dp] Fix Loopback ring teardown path"
2024-09-10 |21f6567| Merge "[qca-nss-dp] Extend Tx Complete errors to track individual error type"
2024-09-10 |7fee76f| Merge "[qca-nss-dp] Destination VP xmit support"
2024-09-09 |0d4ecfd| [qca-nss-dp] Fix Loopback ring teardown path
2024-08-29 |438ab8e| [qca-nss-dp] Move pr_info to pr_debug
2024-08-29 |3f45e3d| Merge "[qca-nss-dp] Fix EDMA Recovery API to Prevent Multiple RX NAPI Add Calls"
2024-08-23 |7a792b1| [qca-nss-dp] Fix EDMA Recovery API to Prevent Multiple RX NAPI Add Calls
2024-07-08 |1227746| [qca-nss-dp] Add support for DDR extended buffer
2024-08-20 |d45bceb| [qca-nss-dp] Extend Tx Complete errors to track individual error type
2024-06-17 |a8f7155| [qca-nss-dp] Destination VP xmit support
2024-08-21 |a5d189b| Merge "[qca-nss-dp] Support for the PPE-VP Qdisc feature"
2024-08-16 |da97bc7| Merge "[qca-nss-dp] Restrict compilation of a file in DP module"
2024-06-22 |bf90fe9| [qca-nss-dp] Support for the PPE-VP Qdisc feature
2024-02-07 |6ceeb8f| [qca-nss-dp] Enable EDMA driver to allocate from beyond 4GB space.
2024-03-19 |4a7ff28| [qca-nss-dp] Restrict compilation of a file in DP module
2024-07-09 |73bad34| [qca-nss-dp] Check for DS node state before getting ppe queue
2024-05-03 |22cdbd6| [qca-nss-dp] Add PPE-DS Enqueue vp to queue mapping
2024-07-04 |5d6ef18| Merge "[qca-nss-dp] NAPI Budget change for KPI improvement"
2024-07-02 |cd0b543| Merge "[qca-nss-dp] Read fake_mac header indication from rx_desc"
2024-07-01 |160b988| [qca-nss-dp] NAPI Budget change for KPI improvement
2024-05-22 |54c2fd1| [qca-nss-dp]: Fixing SA warnings as part of qca-nss-dp module.
2024-06-22 |602534b| [qca-nss-dp] Read fake_mac header indication from rx_desc
2023-11-24 |10210e2| [qca-nss-dp] EDMA register changes for ipq54xx
2024-05-22 |1af0d03| Merge "[qca-nss-dp]: Change to support PPE-VP path for MLO Assist"
2024-05-15 |2acd9f3| [qca-nss-dp]: Change to support PPE-VP path for MLO Assist
2023-09-27 |1ca59f2| [qca-nss-dp] DP changes for ipq54xx
2024-04-18 |bc60c5a| Merge "[qca-nss-dp] Add support for the XGMAC latency computation"
2024-04-18 |6a67d6d| Merge "[qca-nss-dp] Fix the packets processing in the Rx NAPI"
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/17731
Signed-off-by: Robert Marko <robimarko@gmail.com>
This removes -static compile option. The -static option tells GCC to
link this statically with the libc, which we do not want in OpenWrt. We
want to link everything dynamically to the libc. This fixes a compile
problem with glibc.
References: 71bdff91 "ltq-vdsl-mei: Remove static linking"
Signed-off-by: Andre Heider <a.heider@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18056
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Not all devices need Bluetooth UART and USB drivers to be installed together. Three separate drivers have been created:
- kmod-bluetooth
- kmod-hci-uart
- kmod-btusb
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15118
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move Bluetooth modules to new Bluetooth menu from Other menu.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15118
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This allows to attempt an orderly shutdown via L3 request while avoiding
excessive delay in the failure case (up to 6 seconds with the currently
hard-coded 3 attempts).
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250130102108.1606919-2-jan@3e8.eu/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Commit 7bc487c12e ("kernel: ltq-vdsl-vr9-mei: fix warning about
field-spanning write") patched the driver to use unsafe_memcpy in
MEI_IoctlCmdMsgWrite.
However, this is not actually necessary. The assignment of the variable
"pDestPtr" can be modified so that the compiler knows about the correct
size. This way, the check in the fortified memcpy works correctly.
While at it, also adjust all places where similar code is used to copy
from a CMV_STD_MESSAGE_T struct.
Also mark all related structs as packed, because the code (and the
driver in general) seems to rely on that anyway.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250206225444.2521817-2-jan@3e8.eu/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since the update to kernel 6.1, a warning like this appears in the
kernel log:
[ 49.773953] ------------[ cut here ]------------
[ 49.773998] WARNING: CPU: 3 PID: 2349 at target-arm_cortex-a7+neon-vfpv4_musl_eabi/linux-ipq40xx_generic/dsl_cpe_mei-ugw_8.5.2.10/src/drv_mei_cpe_msg_process.c:3570 MEI_IoctlCmdMsgWrite+0x290/0x2c8 [drv_mei_cpe]
[ 49.777670] memcpy: detected field-spanning write (size 4) of single field "pDestPtr" at target-arm_cortex-a7+neon-vfpv4_musl_eabi/linux-ipq40xx_generic/dsl_cpe_mei-ugw_8.5.2.10/src/drv_mei_cpe_msg_process.c:3570 (size 2)
...
[ 50.087078] ---[ end trace 0000000000000000 ]---
The variable "pDestPtr" points to the field "header.index" in a
CMV_STD_MESSAGE_T struct (header is a CMV_STD_MESSAGE_HEADER_T struct).
The offending code intentionally copies data beyond this field, which is
followed by "header.length" and "payload".
To fix this, change the assignment of "pDestPtr" to use the pointer to
the message plus the offset of the "header.index" field. This way, the
compiler knows about the size and thus the false positive warning
disappears.
While at it, also adjust all places where similar code is used to copy
from a CMV_STD_MESSAGE_T struct.
Also mark all related structs as packed, because the code (and the
driver in general) seems to rely on that anyway.
Fixes: https://github.com/openwrt/openwrt/issues/17142
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250206225444.2521817-1-jan@3e8.eu/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The fixes are only for the WRT1900X and WRT1200AC.
It contains:
Deletes the driver's ability to modify the debit table.
Remove skb_get(done_skb) in txdone
Reworking ISR
clean code
Napi replaces tasklet
Add rx_decrypt feature
Signed-off-by: Michael Trinidad <trinidude4@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/17997
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The FDB roaming issues were observed on ipq807x and ipq60xx boards.
The fix depends on API exposed only when NSS_DP_PPE_SUPPORT is enabled.
However, this flag applies to above mentioned platforms only and is
causing the logs to be flooded on other QCA platforms, including ipq50xx,
with:
[ 34.893418] nss-dp 39c00000.dp1 lan: cannot get VSI ID for port 1
[ 34.898370] nss-dp 39c00000.dp1 lan: cannot get VSI ID for port 1
[ 34.904598] nss-dp 39c00000.dp1 lan: cannot get VSI ID for port 1
[ 34.910661] nss-dp 39c00000.dp1 lan: cannot get VSI ID for port 1
So let's apply a dependency on the NSS_DP_PPE_SUPPORT flag and contain
the patch code for ipq807x and ipq60xx within conditional directives.
Tested on: Linksys SPNMX56
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17966
Signed-off-by: Robert Marko <robimarko@gmail.com>
This downstream patch fixes a bug which could flood the logs with the
following message and would eventually lead to a crash.
ath11k c000000.wifi: failed to send HAL_REO_CMD_UPDATE_RX_QUEUE cmd, tid 0 (-105)
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add QCN6122 platform support.
QCN6122 is a PCIe based solution that is attached to and enumerated
by the WPSS (Wireless Processor SubSystem) Q6 processor.
Though it is a PCIe device, since it is not attached to APSS processor
(Application Processor SubSystem), APSS will be unaware of such a decice
and hence it is registered to the APSS processor as a platform device(AHB).
Because of this hybrid nature, it is called as a hybrid bus device.
As such, QCN6122 is a hybrid bus type device and follows the same codepath
as for WCN6750.
This is a reversed engineered and heavily simplified version of below
downstream patch:
https://git.codelinaro.org/clo/qsdk/oss/system/feeds/wlan-open/-/ \
blob/NHSS.QSDK.12.4.5.r2/mac80211/patches/232-ath11k-qcn6122-support.patch
Co-developed-by: George Moussalem <george.moussalem@outlook.com>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
IPQ5018 uses different BDF and caldb addresses for vairous boards,
so let's support reading these addresses from the device tree.
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for the Qualcomm IPQ50xx in the QCA NSS dataplane driver.
The QCA implementation uses depracated DMA api calls and a downstream SCM
call, so convert to proper Linux DMA and SCM api calls.
In addition, add fixed-link support to support SGMII which is used to
connect the internal IPQ50xx switch to an external switch (ex. QCA8337)
Co-developed-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
The codename for IPQ50xx is Maple (abbreviated as 'MP'), so let's pass
the codename to allow the QCA-SSDK to build for the IPQ50xx SoC.
In addition, disable compiling the MP_PHY driver in favor of a native
driver being upstreamed.
Co-developed-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Uses upstream DSA switch modules (rtl8365mb, rtl8366), similar to
RTL8367C and rtl8366rb swconfig drivers.
The package dependencies exclude targets built without kernel CONFIG_OF.
It also fixes the rtl8366rb LED support.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
The three packages base-files, libc and kernel are special, the former
can't be upgraded in place since it's content are modified on startup,
the latter two are virtual packages only used as constraints for the
package manager.
Historically base-files was "locked" via a special OPKG function, the
latter two were hidden from the package index and thereby never picked
as possible upgrade.
Time moved forward and we now have APK and tools like OWUT. The latter
compares available packages with installed packages and generates user
readable output, requiring versions for libc and kernel, too. At the
same time, APK uses a different looking mechanism, which is set during
installation instead of part of the package metadata.
In short, this patch adds version constraints to the three packages,
allowing them to be part of the package index.
Fixes: #17774Fixes: #17775Fixes: efahl/owut#31
Signed-off-by: Paul Spooren <mail@aparcar.org>
The USB PHY on the ar9330 and similar SoCs needs the PHY driver. In
OpenWrt 23.05 it was compiled into the kernel. The kernel 6.6
configuration does not compile it in any more, make the
kmod-usb-chipidea driver select it to add it to the images.
Fixes: https://github.com/openwrt/openwrt/issues/17710
Fixes: 04bdf9b332 ("ath79: disable ath79 USB phy drivers by default")
Link: https://github.com/openwrt/openwrt/pull/17720
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
atm_qos struct should be the same both for user and kernel spaces. Via
the __SO_ENCODE() macro it is used to define the SO_ATMQOS socket IOC.
During the VRX518 support introduction, the atm_trafprm sturct nested
into the atm_qos stucture was update with newer fields that are
referenced by the ATM TC layer of the VRX518 TC driver. These new fields
are intended to communicate information for extra traffic classes
supported by the driver. But we are still using vanilla kernel headers
to build the toolchain. Due to the atm.h header incoherency br2684ctl
from linux-atm tools is incapable to configure the ATM bridge netdev:
br2684ctl: Interface "dsl0" created sucessfully
br2684ctl: Communicating over ATM 0.1.2, encapsulation: LLC
br2684ctl: setsockopt SO_ATMQOS 22 <-- EINVAL errno
br2684ctl: Fatal: failed to connect on socket; File descriptor in bad state
There are two options to fix this incoherency. (a) update the header
file in the toolchain to build linux-atm against updated atm_trafprm and
atm_qos structures, or (b) revert atm_trafprm changes.
Since there are no actual users of the extra ATM QoS traffic classes,
just drop these extra traffic classes from vrx518_tc ATM TC layer and
drop the kernel patch updating atm.h.
Besides fixing the compatibility with linux-atm tools, removing the
kernel patch should simplify kernel updates removing unneeded burden of
maintenance.
Run tested with FRITZ!Box 7530 with disabled extra traffic classes and
then removed them entirely before the submission.
CC: John Crispin <john@phrozen.org>
Fixes: cfd42a0098 ("ipq40xx: add Intel/Lantiq ATM hacks")
Suggested-by: Andre Heider <a.heider@gmail.com>
Reported-and-tested-by: nebibigon93@yandex.ru
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250122222654.21833-4-ryazanov.s.a@gmail.com/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ATM TC layer have some issues which effectively prevent VRX518 from
being used as ADSL modem. Specifically, there one crash during the ATM
layer configuration and wrong PVC ID selection on packet receiving what
breaks RX path. Fix both of the issues. Make subif iface registration
optional to prevent the crash (see more details in the new patch) and
update the hardcoded PVC ID to match the first allocated channel.
Run tested with FRITZ!Box 7530.
Fixes: 474bbe23b7 ("kernel: add Intel/Lantiq VRX518 TC driver")
Reported-and-tested-by: nebibigon93@yandex.ru
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250122222654.21833-3-ryazanov.s.a@gmail.com/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It looks like VRX518 returns phys addr of data buffer in the 'data_ptr'
field of the RX descriptor and an actual data offset within the buffer
in the 'byte_off' field. In order to map the phys address back to
virtual we need the original phys address of the allocated buffer.
In the same driver applies offset to phys address before the mapping,
what leads to WARN_ON triggering in plat_mem_virt() function with
subsequent kernel panic:
WARNING: CPU: 0 PID: 0 at .../sw_plat.c:764 0xbf306cd0 [vrx518_tc@8af9f5d0+0x25000]
...
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = aff5701e
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] SMP ARM
Noticed in ATM mode, when chip always returns byte_off = 4.
In order to fix the issue, pass the phys address to plat_mem_virt() as
is and apply byte_off later for proper DMA syncing and on mapped virtual
address when copying RXed data into the skb.
Run tested with FRITZ!Box 7530 on both ADSL and VDSL (thanks Jan) links.
Fixes: 474bbe23b7 ("kernel: add Intel/Lantiq VRX518 TC driver")
Tested-by: Jan Hoffmann <jan@3e8.eu> # VDSL link
Reported-and-tested-by: nebibigon93@yandex.ru # ADSL link
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250122222654.21833-2-ryazanov.s.a@gmail.com/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These symbols are needed to satisfy lxc dependencies.
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/17553
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update handling of macro __assign_str() to also support the one-argument
variant when building against kernel 6.10 or later. This is needed for
building the next LTS kernel 6.12.
Fixes: 384d079fd8 ("mac80211: update to version 6.11")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/17456
Signed-off-by: Robert Marko <robimarko@gmail.com>
The patch adding temperature sensor support for r8169 has been removed upstream
and the functionality will be added to Realtek PHY instead:
1f691a1fc4
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Change the double-include guard to avoid conflict with the linux kernel header
Reported-by: Tony Ambardar <itugrok@yahoo.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This was the first DSA packaged, and the tagger was made into
a separate package. This is too complicated: the mv88e6xxx
is the only module using this tagger after all, fold the module
for the DSA hardware and the driver for the tagger into a
single package and let modprobe do its job of probing the
tagger for the driver.
Tested on the BMIPS Inteno XG6846.
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250110-mv88e6xxx-single-package-v1-1-223ad7fb312e@linaro.org/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This LED controller has a driver under development which is currently being reviewed by the respective kernel maintainers. They are currently on v11 which is included here.
The LED1202 is a 12-channel low quiescent current LED driver with:
* Supply range from 2.6 V to 5 V
* 20 mA current capability per channel
* 1.8 V compatible I2C control interface
* 8-bit analog dimming individual control
* 12-bit local PWM resolution
* 8 programmable patterns
If the led node is present in the controller then the channel is
set to active.
The output current can be adjusted separately for each channel by 8-bit
analog (current sink input) and 12-bit digital (PWM) dimming control. The
LED1202 implements 12 low-side current generators with independent dimming
control.
Internal volatile memory allows the user to store up to 8 different patterns,
each pattern is a particular output configuration in terms of PWM
duty-cycle (on 4096 steps). Analog dimming (on 256 steps) is per channel but
common to all patterns. Each device tree LED node will have a corresponding
entry in /sys/class/leds with the label name. The brightness property
corresponds to the per channel analog dimming, while the patterns[1-8] to the
PWM dimming control.
Signed-off-by: Manuel Fombuena <fombuena@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17451
Signed-off-by: Robert Marko <robimarko@gmail.com>
35bcf68a6297 wifi: mt76: scan: fix setting tx_info fields
4d8d6e2e7710 wifi: mt76: scan: set vif offchannel link for scanning/roc
e354436db440 wifi: mt76: mt7996: use the correct vif link for scanning/roc
Signed-off-by: Felix Fietkau <nbd@nbd.name>
7a3bcd39ae1f r8169: use helper r8169_mod_reg8_cond to simplify rtl_jumbo_config
e3e9e9039fa6 r8169: align WAKE_PHY handling with r8125/r8126 vendor drivers
330dc2297c82 r8169: improve rtl_set_d3_pll_down
c507e96b5763 r8169: improve __rtl8169_set_wol
83cb4b470c66 r8169: remove leftover locks after reverted change
2cd02f2fdd8a r8169: improve initialization of RSS registers on RTL8125/RTL8126
a3d8520e6a19 r8169: align RTL8126 EEE config with vendor driver
4af2f60bf737 r8169: align RTL8125/RTL8126 PHY config with vendor driver
eb90f876b796 r8169: align RTL8125 EEE config with vendor driver
b8bd8c44a266 r8169: fix inconsistent indenting in rtl8169_get_eth_mac_stats
f75d1fbe7809 r8169: add support for RTL8125D
c4e64095c00c r8169: enable EEE at 2.5G per default on RTL8125B
d64113c6bb5e r8169: remove rtl_dash_loop_wait_high/low
1c105bacb160 r8169: avoid duplicated messages if loading firmware fails and switch to warn level
ac48430368c1 r8169: don't take RTNL lock in rtl_task()
e3fc5139bd8f r8169: implement additional ethtool stats ops
b8bf38440ba9 r8169: enable SG/TSO on selected chip versions per default
854d71c555df r8169: remove original workaround for RTL8125 broken rx issue
1ffcc8d41306 r8169: add support for the temperature sensor being available from RTL8125B
The following patches require backporting additional linux patches:
e2015942e90a r8169: replace custom flag with disable_work() et al
e340bff27e63 r8169: copy vendor driver 2.5G/5G EEE advertisement constraints
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Just one of the devices uses the Marvell MV88E6060 DSA
switch so break this out from the generic kernel config
and into a package selected only by that single device
and probed at boot instead.
The big win is from being able to drop the dsa_core
(~600KB) kernel module out of the common kernel on
devices with no DSA switch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
109114146f9c mt76: only enable tx worker after setting the channel
5fe42ec88fd1 mt76: mt7915: ensure that only one sta entry is active per mac address
1884f568ba02 wifi: mt76: do not add wcid entries to sta poll list during MCU reset
71fa9124d107 wifi: mt76: mt7996: fix NULL pointer dereference in mt7996_mcu_sta_bfer_he
eb85bb3fd5bf wifi: mt76: mt7915: fix eifs value on older chipsets
83e4d4a82e65 wifi: mt76: introduce mt792x_config_mac_addr_list routine
b47e20b440ae wifi: mt76: mt7925: fix NULL deref check in mt7925_change_vif_links
3e3c484726f3 wifi: mt76: mt7925: fix wrong band_idx setting when enable sniffer mode
3f1401a0f035 wifi: mt76: mt7925: fix get wrong chip cap from incorrect pointer
eede99f524e8 wifi: mt76: mt7925: fix the invalid ip address for arp offload
c99e4d51b340 wifi: mt76: mt7996: fix overflows seen when writing limit attributes
af983b2543ed wifi: mt76: mt7915: fix overflows seen when writing limit attributes
af494e2dcc94 wifi: mt76: mt7915: exclude tx backoff time from airtime
6f6a1f7cb381 wifi: mt76: mt7996: exclude tx backoff time from airtime
7f65b1b28b4c wifi: mt76: connac: Extend mt76_connac_mcu_uni_add_dev for MLO
1b5e6abc2e7a wifi: mt76: mt7925: Fix incorrect MLD address in bss_mld_tlv for MLO support
72b4688b3912 wifi: mt76: mt7925: Fix incorrect WCID assignment for MLO
6bd2c044e67a wifi: mt76: mt7925: Fix incorrect WCID phy_idx assignment
1c04e9693466 wifi: mt76: mt7925: fix wrong parameter for related cmd of chan info
01e02947bdbf wifi: mt76: mt7925: Fix CNM Timeout with Single Active Link in MLO
b90b1a1dc71b wifi: mt76: mt7925: Enhance mt7925_mac_link_bss_add to support MLO
53ec7a551f17 wifi: mt76: Enhance mt7925_mac_link_sta_add to support MLO
3c99ef40e0e7 wifi: mt76: mt7925: Update mt7925_mcu_sta_update for BC in ASSOC state
285efc6afaec wifi: mt76: mt7925: Update mt792x_rx_get_wcid for per-link STA
e5c0d1289e6c wifi: mt76: mt7925: Update mt7925_unassign_vif_chanctx for per-link BSS
67dcd5c888c4 wifi: mt76: mt7925: Update secondary link PS flow
fd4d6f87072f wifi: mt76: mt7925: Init secondary link PM state
6d972b5b9d6a wifi: mt76: mt7925: Update mt7925_mcu_uni_[tx,rx]_ba for MLO
3acc6cbb9556 wifi: mt76: mt7925: Cleanup MLO settings post-disconnection
0aab0c61ce92 wifi: mt76: mt7925: Properly handle responses for commands with events
15bead1b0041 wifi: mt76: do not hold queue lock during initial rx buffer alloc
732044a949d5 wifi: mt76: mt7925: config the dwell time by firmware
9ba311ec6afa wifi: mt76: mt7921: introduce CSA support
5d12c7404c22 wifi: mt76: mt7921: add rfkill_poll for hardware rfkill
ef965d408b79 wifi: mt76: mt7925: replace zero-length array with flexible-array member
f8563589c72d wifi: mt76: mt7921u: Add VID/PID for TP-Link TXE50UH
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Simplify patch with gpiochip_add_data, struct reduction, new GPIO API,
and header cleanup.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16635
Signed-off-by: Robert Marko <robimarko@gmail.com>
These only work with and are useful with mach files. Now that those are
gone, this can go too.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16635
Signed-off-by: Robert Marko <robimarko@gmail.com>
This goes away in kernel 6.12 upstream.
Get ahead of the curve by fixing all the local patches as well.
Get rid of CONFIG_OF. It's needed now.
Refreshed all patches.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16635
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix bogus reference to kmod-nf-conntrack-timeout, fixing the warning
`WARNING: Makefile 'package/kernel/linux/Makefile' has a dependency on
'kmod-nf-conntrack-timeout', which does not exist`.
Fixes: 0e2dcfc4f4 ("netfilter: add kmod-nfnetlink-ct{helper,timeout}")
Signed-off-by: Joel Low <joel@joelsplace.sg>
Link: https://github.com/openwrt/openwrt/pull/17388
Signed-off-by: Robert Marko <robimarko@gmail.com>
- drop patches accepted upstream
- include build fixes in the tarball
- based on https://github.com/nbd168/backports commit 410656ef04d2
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Not needed. Everything can be replaced with devm.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16869
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Shorter and more consistent with other drivers.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16869
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
I have no idea why this is even here. Simplifies the code with direct
returns.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16869
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Not needed as all the older kernels are gone.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16869
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This file does not use a coding style consistent with the kernel. Run
clang-format with the kernel's .clang-format file.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16869
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Package bnxt_en kernel module for Broadcom NetXtreme-C/E based Ethernet
network chips like BCM573xx and BCM574xx.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17301
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Images for xrx200 8M flash are either not building due to image
size (TD-W8970, TD-W8980) or building such that the available
free space in the overlayfs is too little to be useful.
To keep images for these devices buildable, move them into a
small flash variant of the xrx200 subtarget. As these devices
are NOR flash only, remove NAND and UBI references from the
kernel config to gain some additional image size reduction.
The apparent 8M flash devices Arcadyan VGV7510KW22-brn,
Arcadyan VGV7519-brn and Lantiq Easy80920-nor seem to exist in
order to create special "factory" installation images for these
devices (which actually have larger flash: 16MB for the
Arcardyan devices; 64MB for the Lantiq device). As a
considerable amount of surgery would appear to be required to
the uboot-lantiq package structure to separate the "factory"
from the "sysupgrade" device recipes for these devices they
remain in the xrx200 target - if factory images aren't now
created, 23.05.x factory images should suffice for initial
installation.
Tested on: Netgear DM200, TP-Link TD-W8980,
AVM Fritz7490 (xrx200 subtarget: image build only)
Fixes: https://github.com/openwrt/openwrt/issues/16761
Signed-off-by: Andrew MacIntyre <andymac@pcug.org.au>
Link: https://github.com/openwrt/openwrt/pull/17113
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
refresh the following patch for ath12k
001-wifi-ath12k-add-11d-scan-offload-support-and-handle-country-code-for-WCN7850.patch
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17246
Signed-off-by: John Crispin <john@phrozen.org>
This reverts commit 1cea889c96.
This reverts commit 5fd86d66c1.
The patch is causing build servers to fail. Revert it for now.
Signed-off-by: John Crispin <john@phrozen.org>
This option enables support for monochrome LEDs that are grouped into multicolor
LEDs which is useful in the case where LEDs of different colors are physically
grouped in a single multi-color LED and driven by a controller that doesn't have
multi-color support.
Signed-off-by: Jonathan Brophy <professor_jonny@hotmail.com>
Link: https://github.com/openwrt/openwrt/pull/16397
Signed-off-by: John Crispin <john@phrozen.org>
Add an ucode based re-implementation of iwinfo. The tool behaves like the old
one with a few minor output differences. It is now possible to add -j to any
command resulting in JSON output.
The new code is currently opt-in via WIFI_SCRIPTS_UCODE and defaults to
EXPERIMENTAL.
Signed-off-by: John Crispin <john@phrozen.org>
This adds support for RTL8812au/RTL8821au USB adapters.
Run-tested: x86/64/rockchip
USB adapters tested: Alfa AWUS036ACS, D-Link DWA-171 A1.
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17079
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport support for RTL8812AU/RTL8821AU USB adapters
Manually backported patch:
045-v6.13-wifi-rtw88-Enable-the-new-RTL8821AU-RTL8812AU-driver
Patches from 046 to 051 are pending.
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17079
[Move BPAUTO_WANT_DEV_COREDUMP to original patch]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds the Linux kernel mainline driver "leds-ktd202x" for the
KinetIC KTD2026 and KTD2027 RGB/RBGW controller with I2C interface that was
introduced in kernel version 6.7, last changed in mainline on 2024-05-31.
At least the Acer Connect Vero W6m (a variant of the Acer Predator Connect
W6 without 2.5G eth1 port, usb3 port, and the 6 on-board gpio RGB LEDs) is
equipped with a KTD2026 (and a single RGB LED attached to it used by the
stock firmware as status LED), and maybe other router devices also are.
Signed-off-by: George Oldfort <openwrt@10099.de>
Link: https://github.com/openwrt/openwrt/pull/16860
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Change the dependency on the kmod-media-controller from depends to
select.
Fixes: 1095925246 ("kernel: add kmod-media-controller dependency for kmod-usb-audio")
Link: https://github.com/openwrt/openwrt/pull/17058
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Netatalk v4 reintroduces AppleTalk and this module is required for
layer 3 protocol support.
Module was removed in kernel 4.14 for OpenWrt 18.06 (commmit
14a0131, 22/02/2018). At the time nothing used it as Netatalk v3
did not support AppleTalk.
Not building ipddp feature/module like it was in the past, as
recommended by upstream Netatalk maintainers.
Signed-off-by: Antonio Pastor <antonio.pastor@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16979
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These packages are needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The snd-usb-audio drivers uses media controller if media controller is set.
So add kmod-media-controller as dependency.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It is needed for the stm32/stm32mp1 subtarget.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
All stm32 devices use BCM43430 Wi-Fi interface in SDIO mode.
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/16716
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Disable drm-i915 module for target x86/geode.
Fixes: 77cfe8f ("x86: make i915 as a kmod with required firmware")
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16977
Signed-off-by: Robert Marko <robimarko@gmail.com>
i915 driver requires to load correct firmware to work on latest x86
GPU, it is more reasonable to make it as a kernel module, so that
initramfs is not required, and it can also save some space from the
kernel image comparing being a built-in driver
Signed-off-by: Joe Zheng <joe.zheng@intel.com>
Link: https://github.com/openwrt/openwrt/pull/16276
Signed-off-by: Robert Marko <robimarko@gmail.com>
8dfead68c202 wifi: mt76: mt7915: hold dev->mutex while interacting with the thermal state
d508a6eb935d wifi: mt76: mt7996: use mac80211 .sta_state op
57019e663f57 wifi: mt76: add code for emulating hardware scanning
dc4c2bdf7c56 wifi: mt76: add support for allocating a phy without hw
8cd0263f92e1 wifi: mt76: rename struct mt76_vif to mt76_vif_link
99df84d62883 wifi: mt76: add vif link specific data structure
dcc6f158d759 wifi: mt76: mt7996: split link specific data from struct mt7996_vif
d388deab9e73 wifi: mt76: initialize more wcid fields mt76_wcid_init
d026be405c54 wifi: mt76: add chanctx functions for multi-channel phy support
0b05795ca81c wifi: mt76: remove dev->wcid_phy_mask
0b526090de95 wifi: mt76: add multi-radio support to a few core hw ops
aeedee5c0a2c wifi: mt76: add multi-radio support to tx scheduling
fc0ff17b53ff wifi: mt76: add multi-radio support to scanning code
f19cbcf83400 wifi: mt76: add multi-radio remain_on_channel functions
42429ae0eaf6 wifi: mt76: mt7996: use emulated hardware scan support
f9d593d4a6b4 wifi: mt76: mt7996: pass wcid to mt7996_mcu_sta_hdr_trans_tlv
807090b28661 wifi: mt76: mt7996: prepare mt7996_mcu_add_dev/bss_info for MLO support
252baa7bf477 wifi: mt76: mt7996: prepare mt7996_mcu_add_beacon for MLO support
9ee990050305 wifi: mt76: mt7996: prepare mt7996_mcu_set_tx for MLO support
bf12cc404334 wifi: mt76: mt7996: prepare mt7996_mcu_set_timing for MLO support
60bf2bef95dc wifi: mt76: connac: prepare mt76_connac_mcu_sta_basic_tlv for MLO support
1289737e12a8 wifi: mt76: mt7996: prepare mt7996_mcu_update_bss_color for MLO support
7c00df0e7e57 wifi: mt76: connac: rework connac helpers
484e3f289a40 wifi: mt76: mt7996: move all debugfs files to the primary phy
d258f4e3e1ca wifi: mt76: mt7996: switch to single multi-radio wiphy
c246fa545119 wifi: mt76: mt7996: fix monitor mode
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Most links and info on the org page are broken or defunct, and all new
versions are available on the github based repo anyway.
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16910
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
For the last ten years, nobody has noticed that this driver doesn't
actually say what it is for. ;)
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16910
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
vrx518_tc currently sets the interface maximum MTU to the ethernet default
of 1500 bytes by default via ether_setup() called from ptm_setup().
To support 1508 byte baby jumbo frames (RFC4638) for PPPoE connections
over VDSL links as already supported by the VR9 ltq_ptm driver ([1], [2])
set the interface maximum MTU to MAX_MTU.
MAX_MTU is defined in dcdp/inc/tc_common.h to 2002 bytes and this value is
used in ptm_change_mtu() and elsewhere as the maximum MTU, however this is
short circuited by checks against the interface maximum MTU.
[1]: https://forum.openwrt.org/t/fritzbox-7530-and-rfc4638-baby-jumbo-frames/181327
[2]: https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=8a2a20e71e2909f84dab47e51dfda9e292a6c1ae
Signed-off-by: Andrew MacIntyre <andymac@pcug.org.au>
Link: https://github.com/openwrt/openwrt/pull/16856
Signed-off-by: Robert Marko <robimarko@gmail.com>
Package kmod-drm-panel-mipi-dbi as well as modules it depends on in
order to support a wide range of MIPI DBI complaint SPI-connected
TFT panels.
See https://github.com/notro/panel-mipi-dbi/ for more information on
how to use specific panels.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Patches weren't refreshed when r8168 was updated to v8.054.00 in a85e18b53f.
Fixes: a85e18b53f ("kernel: r8168: update to v8.054.00")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
zero length arrays are deprecated.
Fixes coccinelle warning:
WARNING use flexible-array member instead
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16848
Signed-off-by: Robert Marko <robimarko@gmail.com>
Package gs_usb CAN driver, which is for Geschwister Schneider and
bytewerk.org candleLight compatible USB/CAN interfaces.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Drop limitation on depending on only armv8 for armsr target as those
module should support both 32 and 64 bits systems.
Only thunderx-net actually require 64 bit systems.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reintroduce rt61/rt73 support as they looks to be pretty standard and
currently required by Gemini or Xway-legacy targets.
Notice that they are b/g card.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add INET diag socket monitoring interface module for MultiPath TCP.
It allows using native Linux socket diagnostic tools such as 'ss' for
Multipath TCP connections.
Co-authored-by: Rodrigo B. de Sousa Martins <rodrigo.sousa.577@gmail.com>
Signed-off-by: sKy King <29267720+sKyissKy@users.noreply.github.com>
Link: https://github.com/openwrt/openwrt/pull/12884
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is a preparation for adding support for dsl_cpe_pipe.sh with a
similar set of commands compared to the VDSL variant.
The configuration is simplified by using the "--enable-model" option.
Other options are chosen to match the VDSL variant, while also making
sure that previously enabled options stay like that. However, ReTx
options stay disabled, because of incompatibility with the ubus code.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20241019174041.1281093-2-jan@3e8.eu/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Allows removal of the remove function by letting devm handle everything.
Avoids gotos as well.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16507
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set the boot flag for the igc, mlx4-core, and mlx5-core network device drivers
to load them at a more early stage of the boot process.
This is required for network drivers whose network interface PCI paths are set
via ucidef_set_network_device_path inside the 02_network script since it is
called after kernel modules are loaded from modules-boot.d but before they are
loaded from the modules.d directory.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/16560
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Upstream patch updated to fix kernel 6.6 compilation. It was also split
up into 5. Do the same here.
The patches are taken from this upstreasm PR:
https://github.com/kaloz/mwlwifi/pull/413
Renamed other patches so as to not overlap.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15452
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add Realtek RTL8192DU support to the rtlwifi package.
The RTL8192DU chipset is a 802.11a/b/g/n chip which supports 2.4 and 5 GHz at
up to 40 MHz channel bandwidth, three hardware variations exist:
* single MAC/ single PHY
* single MAC/ double PHY
* double MAC/ double PHY
This driver has been successully tested on a single MAC/ single PHY variant
0bda:8194 (DeLock 88540, https://www.delock.com/produkt/88540/merkmale.html)
rtl_usb: rx_max_size 15360, rx_urb_num 8, in_ep 1
rtl8192du: Driver for Realtek RTL8192DU WLAN interface
rtl8192du: Loading firmware file rtlwifi/rtl8192dufw.bin
ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
usbcore: registered new interface driver rtl8192du
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* mesh point
* P2P-client
* P2P-GO
interface combinations are not supported
The new rtlwifi based driver rtl8192du has been merged in kernel v6.11.
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16721
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The swconfig-based b53 driver for the BCM53128 switch stopped working
after commits b2cfed48f6 (Revert "swconfig: fix Broadcom b53 support")
and e4e410733f (kernel: export switch_generic_set_link() symbol). This
rendered the 8 LAN ports of the EdgeSwitch 8XP non-functional, so the
image compilation for the device was disabled (5a1d7d8c1b).
This commit adds the kmod-dsa-b53-mdio and kmod-dsa-b53 packages
with the upstream B53 DSA driver, replacing the swconfig-based
kmod and kmod-switch-bcm53xx-mdio downstream ones that are not used by
any other device.
The 8 LAN ports of the EdgeSwitch 8XP are usable again. The 02_network
init script has been updated with the new DSA interfaces lan1 .. lan8.
Image building has been reenabled for the device, adding the usual DSA
incompatibility notice.
Tested on a Ubiquiti EdgeSwitch 8XP.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Link: https://github.com/openwrt/openwrt/pull/11680
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add the Realtek RTL8922AE support to rtw89 package.
The 8922A is a 802.11be chip that can support 2/5/6GHz 160MHz.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/16700
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This solution that is needed for some routers to provide proper
LED activity when controlled directly by the MV88E6xxx switch,
has just been merged in upstream Linux.
Make this patch 901 as other backports from earlier kernels
are in patch 896 and this is the first free number after
that.
Patch offsets in pending patches are augmented as part of
the refresh.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
513bd7683746 Revert "wifi: mt76: mt7915: disable the second PCIe link for MT7915"
703c6b78c133 wifi: mt76: mt7915: firmware restart on devices with a second pcie link
Signed-off-by: Felix Fietkau <nbd@nbd.name>
RmNet driver provides a transport agnostic MAP (multiplexing and
aggregation protocol) support in embedded module. Module provides
virtual network devices which can be attached to any IP-mode
physical device.
This is commonly used on Qualcomm based modems for data aggregation.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Wrong variable name from copy/paste.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16640
Signed-off-by: Robert Marko <robimarko@gmail.com>
Allows remove the _remove function as devm calls mutex_destroy
automatically.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16615
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update channels when country set.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16613
Signed-off-by: Robert Marko <robimarko@gmail.com>
Trying to compile ath10k-ct without mac80211 debugfs support will result in:
openwrt/build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/linux-ipq806x_generic/ath10k-ct-regular/ath10k-ct-2024.07.30~ac71b14d/ath10k-6.10/wmi.h:8083:2: error: #warning Please enable ATH10K-DEBUGFS kernel option for optimal support for CT firmware. [-Werror=cpp]
8083 | #warning Please enable ATH10K-DEBUGFS kernel option for optimal support for CT firmware.
| ^~~~~~~
cc1: all warnings being treated as errors
So, since the driver itself is saying that debugfs is required, then
lets make ath10k-ct select mac80211 debugfs support which is selected
by default anyway.
Fixes: #16302
Link: https://github.com/openwrt/openwrt/pull/16619
Signed-off-by: Robert Marko <robimarko@gmail.com>
The mac80211 driver backport has been updated to version 6.11. Let's
also push ath10k-ct driver forward. The unsupported feature
'NL80211_EXT_FEATURE_ETHTOOL_VDEV_STATS' has been dropped since it
looks like something for debugging and not supported by the mainline.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16514
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Allows removal of _remove function.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16587
Signed-off-by: Robert Marko <robimarko@gmail.com>
Build hostapd with 11BE support for
both mt7925e and mt7925u.
Signed-off-by: Marek Puzyniak <marek.puzyniak@holisticon.pl>
Link: https://github.com/openwrt/openwrt/pull/16571
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Avoid the following errors:
[ 9.219272] mt7996e 0000:01:00.0: Direct firmware load for mediatek/mt7996/mt7992_eeprom_2i5i.bin failed with error -2
[ 9.229975] mt7996e 0000:01:00.0: Falling back to sysfs fallback for: mediatek/mt7996/mt7992_eeprom_2i5i.bin
Fixes: 2f7d22d ("mt76: update to Git HEAD (2024-09-29)")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
1231d45dcb5e wifi: mt76: mt7915: check devm_kasprintf() returned value
042082027b3f wifi: mt76: mt7921: Check devm_kasprintf() returned value
4a95c1a81eee wifi: mt76: Avoid multiple -Wflex-array-member-not-at-end warnings
5fdb1841f726 wifi: mt76: mt7925: fix a potential association failure upon resuming
eeb51b527377 wifi: mt76: mt7925: convert comma to semicolon
d4b3b302ceb9 wifi: mt76: mt7615: check devm_kasprintf() returned value
922e515bd8e0 wifi: mt76: mt7925: fix a potential array-index-out-of-bounds issue for clc
bec8cb851d99 wifi: mt76: mt7925: replace chan config with extend txpower config for clc
d10ce9d65dac wifi: mt76: remove mt76_calculate_default_rate()
6685a2f4c217 wifi: mt76: mt7996: remove phy->monitor_vif
a2a9d9826277 wifi: mt76: do not increase mcu skb refcount if retry is not supported
059342ca6a68 wifi: mt76: move mt76_tm_policy to from testmode.h to mt76.h
8bef11443290 wifi: mac80211: inform the low level if drv_stop() is a suspend
4b16d2bfdcbd wifi: mac80211: handle color change per link
4529cddb6718 wifi: mt76: mt7996: extend flexibility of mt7996_mcu_get_eeprom()
4364571e4b2b wifi: mt76: mt7996: add support for more variants
8c86aa304ea1 wifi: mt76: mt7996: set correct background radar capability
addfbd141863 firmware: add latest mt7996 + mt7992 firmware
5ba4981f8b92 wifi: mt76: mt792x: add P2P_DEVICE support
dc32780c7fcd wifi: mt76: mt7921s: fix a potential firmware freeze during startup
7b5d653ea90e wifi: mt76: mt7925: fix off by one in mt7925_load_clc()
1e57d2da94c9 wifi: mt76: mt7615: Convert comma to semicolon
7aca94abac47 wifi: mt76: mt7915: fix slot time for 5/6GHz
e3e6d490ab90 wifi: mt76: mt7915: Fix mesh scan on MT7916 DBDC
ee693260c521 firmware: move mt7996 firmware to the right place
867accf4f4aa wifi: mt76: mt7996: Add eht radiotap tlv
7c4d6e403381 wifi: mt76: Fix EHT NSS radiotap reporting.
71c3949fa8ac wifi: mt76: mt7921: fix a potential scan no APs
61641da04c9e mt76: mt76u_vendor_request: Do not print error messages when -EPROTO
680bc70f161f wifi: mt76: mt7921: fix using incorrect group cipher after disconnection.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The only supported kernel in the main branch now is version 6.6. It's
time to clean up these useless codes and patches.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The virtio_find_vqs() ABI has been changed since the 6.11 kernel.
Switch back to using the old ABI to fix the build error:
../mac80211-regular/backports-6.11/drivers/net/wireless/virtual/mac80211_hwsim.c: In function 'init_vqs':
../mac80211-regular/backports-6.11/drivers/net/wireless/virtual/mac80211_hwsim.c:6632:31: error: array type has incomplete element type 'struct virtqueue_info'
6632 | struct virtqueue_info vqs_info[HWSIM_NUM_VQS] = {
| ^~~~~~~~
../mac80211-regular/backports-6.11/drivers/net/wireless/virtual/mac80211_hwsim.c:6637:16: error: too few arguments to function 'virtio_find_vqs'
6637 | return virtio_find_vqs(vdev, HWSIM_NUM_VQS,
| ^~~~~~~~~~~~~~~
In file included from ../mac80211-regular/backports-6.11/drivers/net/wireless/virtual/mac80211_hwsim.c:38:
./include/linux/virtio_config.h:224:5: note: declared here
224 | int virtio_find_vqs(struct virtio_device *vdev, unsigned nvqs,
| ^~~~~~~~~~~~~~~
../mac80211-regular/backports-6.11/drivers/net/wireless/virtual/mac80211_hwsim.c:6632:31: error: unused variable 'vqs_info' [-Werror=unused-variable]
6632 | struct virtqueue_info vqs_info[HWSIM_NUM_VQS] = {
| ^~~~~~~~
../mac80211-regular/backports-6.11/drivers/net/wireless/virtual/mac80211_hwsim.c:6639:1: error: control reaches end of non-void function [-Werror=return-type]
6639 | }
| ^
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Always depend on PCI and don't build on platforms
without PCI.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16475
Signed-off-by: Robert Marko <robimarko@gmail.com>
The rss variant should conflict with the default.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/16460
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The rss variant should conflict with the default.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/16460
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Avoids having to handle EPROBE_DEFER manually.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16456
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix ltssm crashes on BPI-Rx boards.
Seems read32/write32 using wrong address which
is not a problem on x86/64 PCI controllers.
But have issues on BPI-Rx boards.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15945
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Allow to build ath11k and other drivers using
qcom-qmi-helpers together (eg. ath12k).
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15945
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
1. Remove outdated symbol CONFIG_USB_OHCI_ATH79.
The ath79 OHCI USB was already supported by the generic driver
kmod-usb-ohci. And this kernel symbol has been dropped since
upstream commit:
53d473fc1e38 ("usb: host: Remove the deprecated ATH79 USB host config options")
2. Add ath79 USB phy package to the OHCI dependencies.
Both EHCI and OHCI require it on the ath79 target.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16380
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
