The DRM modules for simple (ie. raw, non-eDP) panels can be used also
by platforms others than Freescale i.MX.
Create an individual package for it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Package kernel modules for PS/2 mouse support, mostly to allow
using touchpads and trackpoints built-into laptops (many of those
are connected using classic i8052-compatible PS/2 I/O).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Buildbot revealed that on the x86/geode target, on which CONFIG_DRM=y isn't set,
kmod-i2c-hid misses the dependency on kmod-drm. Fix that to fix the build for
x86/geode.
Fixes: c83e275c9b ("kernel: package modules for I2C HID devices")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The interrupt handler reads from the mailbox if no other reason for the
interrupt is known. If a spurious interrupt is received just after a
mailbox message has been sent, this means that the response to the
previous message is read again and returned by DSL_BSP_SendCMV instead
of the actual response.
To fix this, check the status register before reading from the mailbox
in the interrupt handler.
Tested on Fritzbox 7320. Without this change, there is occasionally a
kernel panic due to an out-of-bounds memory access in the ltq-adsl
driver (in DSL_DRV_DEV_G997_SnrAllocationNscGet), as a result of an
incorrect value returned by DSL_DRV_DANUBE_CmvRead. This is reproducible
by calling "dsl_cpe_pipe.sh g997dsnrg 1 1" multiple times.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://github.com/openwrt/openwrt/pull/19385
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Package driver modules for I2C HID devices such as touchpads,
touchscreens and trackpoints found on some laptops. Only the ACPI
firmware variant of the driver is packaged for now as that's what I got
for testing.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The number of serial interfaces for the chip 8250 can be configured at
build time. This is currently not configurable and is always set to 16
interfaces. This is too little for some small embedded devices and too much
for others (x86_64). Therefore, this commit creates the possibility to set
this at compile time.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/19217
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Allows to enable/disable attached regulators from userspace, i.e. by
simply writing value to a sysfs exported state file. Useful in case of
USB port VBUS toggled by GPIO.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250529202033.28250-1-tmn505@terefe.re/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
6df761e0e6c7 mt76: fix signature of platform_driver remove funtions for newer kernels
5724be1a6b12 wifi: mt76: Replace strlcpy() with strscpy()
c4a114e2b8c9 wifi: mt76: fix queue assignment for deauth packets
243e572d89fc wifi: mt76: add a wrapper for wcid access with validation
e41c7785589f wifi: mac80211: get tx power per link
d70f62b8f1c7 wifi: mt76: fix vif link allocation
7b3cd3274a24 wifi: mt76: mt7996: Fix secondary link lookup in mt7996_mcu_sta_mld_setup_tlv()
cf89b6218043 wifi: mt76: mt7996: Rely on for_each_sta_active_link() in mt7996_mcu_sta_mld_setup_tlv()
d71108eedab1 wifi: mt76: mt7996: Do not set wcid.sta to 1 in mt7996_mac_sta_event()
32f8c5849ed1 wifi: mt76: mt7996: Fix mlink lookup in mt7996_tx_prepare_skb
ffff9f71e29d wifi: mt76: mt7996: Fix possible OOB access in mt7996_tx()
afe63e758196 wifi: mt76: mt7996: Fix valid_links bitmask in mt7996_mac_sta_{add,remove}
68dd28b99dad wifi: mt76: mt7996: Add MLO support to mt7996_tx_check_aggr()
293778652452 wifi: mt76: mt7996: Move num_sta accounting in mt7996_mac_sta_{add,remove}_links
a94166b21e20 wifi: mt76: Get rid of dma_sync_single_for_device() for MMIO devices
87873d854e51 wifi: mt76: mt7925: Fix null-ptr-deref in mt7925_thermal_init()
06ba3d5e91f4 wifi: mt76: mt792x: Limit the concurrent STA and SoftAP to operate on the same channel
b9f4e0df317d wifi: mt76: mt792x: improve monitor interface handling
ec95319fd3fb wifi: mt76: mt7921s: Introduce SDIO WiFi/BT combo module card reset
dd2d862251cb firmware: add missing mt7990 eeprom files
05eaa56bc7a4 firmware: update mt7992 firmware to 20250328
32ca2b6db354 firmware: update mt7996 firmware to 20250328
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The upstream submission for this mandates the node to be named wifi
instead of wmac. Change all ath79 entries to match the new names and
remove the compatibility patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19328
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k ahb patch was updated to match the latest upstream version,
however the openwrt DT files still use the older names.
Add those as extra entries in order to remain compatible until DT files
are fixed.
Fixes: 88f4c32060 ("mac80211: update to version 6.14.11")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This will allow more flexibility in using PHY drivers as kmods.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18435
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for Maxlinear GPHY module. Also add support for
kmod-polynomial, which is a dependency for this module.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18435
Signed-off-by: Robert Marko <robimarko@gmail.com>
In the development history of Intel's drivers, the i40evf driver was later
renamed the iavf driver. For example, some documents mention that
Intel® Network Connections Software Version 24.0 renamed the i40evf
and ixlv drivers to iavf. In subsequent versions, the i40evf driver was
gradually removed, and its functions were taken over by the iavf driver.
In the Linux system, relevant configuration instructions also exist. For
instance, the User Guide for X722 Onboard Network Card states that the
i40evf driver module should be disabled, and the iavf driver should be
installed and used.
blamed commit: 5d81b28a82
Signed-off-by: xiao bo <peterwillcn@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19197
Signed-off-by: Robert Marko <robimarko@gmail.com>
The stm32-dfsdm-adc module depends on it (kernel 6.12).
Signed-off-by: Thomas Richard <thomas.richard@bootlin.com>
Link: https://github.com/openwrt/openwrt/pull/18740
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The memory mapped TPM interface (TIS) can be used for
emulated or virtualized TPM instances with QEMU and
a simulation package like swtpm.
On QEMU the device will appear in the device tree
with a "tcg,tpm-tis-mmio" compatible.
For example:
qemu-system-aarch64 -machine virt -cpu max \
-bios u-boot.bin \
-nographic \
.... \
-hda openwrt-armsr-armv8-combined-efi.img \
-chardev socket,id=chrtpm,path=/tmp/mytpm/swtpm-sock \
-tpmdev emulator,id=tpm0,chardev=chrtpm \
-device tpm-tis-device,tpmdev=tpm0
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Link: https://github.com/openwrt/openwrt/pull/19188
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Change deprecated function strlcpy to strscpy
for compatibility with kernel 6.12.
strlcpy() reads the entire source buffer first.
This read may exceed the destination size limit.
This is both inefficient and can lead to linear read
overflows if a source string is not NUL-terminated [1].
In an effort to remove strlcpy() completely [2], replace
strlcpy() here with strscpy().
Direct replacement is safe here since DEV_ASSIGN is only used by
TRACE macros and the return values are ignored.
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#strlcpy
[2] https://github.com/KSPP/linux/issues/89
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18927
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport accepted BCM5325 patches from net-next.
These patches will be merged in the v6.17 kernel window.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
QCN6122 wifi in fw-memory-mode 1 has a slightly larger caldb size than
currently defined in the ath11k driver. When coldboot calibration was
disabled, the fw mem mode was changed from 2 (256MB mem profile) to 1
(512MB mem profile), which is the correct setting for devices in scope.
However, in fw mem mode, the caldb size is 0x500000 instead of the max
0x480000 defined in the driver, causing QCN6122 wifi failing to boot:
ath11k b00a040.wifi1: qmi mem size is low to load caldata
ath11k b00a040.wifi1: failed to assign qmi target memory: -22
As such, change the max caldb memory size accordingly.
This macro is used by the driver only as a max size limit to validate
the requested caldb size returned by QMI. Different ath11k wifi chips
have different caldb sizes (for ex. the size for IPQ5018 is 0x200000).
Fixes: cf715a2305 ("wifi: ath11k: disable coldboot calibration for ipq5018")
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19118
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove upstream backport patch.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/19100
Signed-off-by: Robert Marko <robimarko@gmail.com>
Coldboot calibration does not work causes the firmware to crash during
wifi startup. So let's disable coldboot calibration until a solution is
found.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19083
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add new setting CONFIG_NET_DSA_REALTEK_RTL8366RB_LEDS which
was introduced in kernel 6.12 and allows enabling LEDs for
the Realtek RTL8366RB subdriver.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Link: https://github.com/openwrt/openwrt/pull/18654
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add kernel package for DesignWare I2C platform controller.
This controller is used on the RP1 SoC found on RPi 5 devices.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The ENC28J60 is a 10 Mbps half-duplex Ethernet controller interfaced via SPI.
It achieves real-world bandwidth up to 5Mbit/s on devices like the RPi Zero due
to SPI limits.
Commonly used with Raspberry Pi Zero boards for wired network connectivity.
Signed-off-by: Albrecht Lohofener <albrechtloh@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19048
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Add kernel packages for DesignWare SPI core and MMIO controllers.
This is needed for the RP1 SoC found on RPi 5 devices.
Tested with a Microchip ENC28J60 Ethernet controller on a RPi 5.
Signed-off-by: Albrecht Lohofener <albrechtloh@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19049
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
building with CONFIG_ALL_KMODS unearthed all sorts of interesting
failures
ERROR: module 'crypto/chacha-x86_64.ko' is missing.
ERROR: module 'crypto/poly1305-x86_64.ko' is missing.
ERROR: module 'crypto/curve25519-x86_64.ko' is missing.
ERROR: module 'crypto/camellia-x86_64.ko' is missing.
These stem from the main UML Makefile.
|# UML only makes sense on linux
|ifeq ($(HOST_OS),Linux)
| ifeq ($(HOST_ARCH),x86_64)
|
|ARCH:=x86_64
|BOARD:=uml
The modules in question define x86_64 optimized version and
the OpenWrt's buildsystem expects that these modules will be present.
SPI is not available due to the UML Architecture not setting HAS_IOMEM.
In the future, UML could get (virtualized) IOMEM and/or SPI could drop
the HAS_IOMEM dependency. A patch for the latter has been sent:
<https://lore.kernel.org/linux-spi/20250530234941.950431-1-chunkeey@gmail.com/T/#u>
mt76: Unfortunately, the firmware packages are picked up, but the
associated drivers can't be build because iowrite32+ioread32 are
not defined.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This adds support for RTL8814AE/RTL8814AU PCI/USB adapters.
Run-tested: x86/64/rockchip
USB adapter tested: Hawking HW17ACU Wireless-AC1750.
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19052
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Linux 6.8 changed the directory structure for the video-code driver.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/19029
Signed-off-by: Nick Hainke <vincent@systemli.org>
The original OF code effectively does a reset at ahb.c but then again in
hw.c. For AR9330, it's already done in the driver and with the others,
there are patches in here that do the same. hw.c looks like the proper
place to handle this.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19031
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fixes ath9k on ar934x platforms.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19031
Signed-off-by: Robert Marko <robimarko@gmail.com>
Building against recent kernel versions (noticed with 6.12) and -Werror
can fail because a macro MAX(a,b) is already defined in minmax.h or
kernel.h before 5.10.
In file included from ../mwlwifi-2025.02.06~db97edf2/hif/fwcmd.h:23,
from ../mwlwifi-2025.02.06~db97edf2/core.c:25:
../mwlwifi-2025.02.06~db97edf2/hif/hostcmd.h:1124:9: error: "MAX" redefined [-Werror]
1124 | #define MAX(a, b) (((a) > (b)) ? (a) : (b))
| ^~~
In file included from usr/include/mac80211-backport/linux/minmax.h:4,
from ./include/linux/kernel.h:28,
from usr/include/mac80211-backport/linux/kernel.h:3,
from ./include/linux/skbuff.h:13,
from usr/include/mac80211-backport/linux/skbuff.h:3,
from ./include/linux/if_ether.h:19,
from usr/include/mac80211-backport/linux/if_ether.h:3,
from ./include/linux/etherdevice.h:20,
from usr/include/mac80211-backport/linux/etherdevice.h:3,
from ../mwlwifi-2025.02.06~db97edf2/core.c:18:
./include/linux/minmax.h:330:9: note: this is the location of the previous definition
330 | #define MAX(a,b) __cmp(max,a,b)
| ^~~
Add a pending upstream patch which replaces the MAX(a,b) macro to avoid
conflicts and allow compilation with 6.12
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/18980
Signed-off-by: Robert Marko <robimarko@gmail.com>
446db12b1fd3 MP: fix uniphy reset in phy to phy link scenario
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18774
Signed-off-by: Robert Marko <robimarko@gmail.com>
3423fdacac63 ssdk_clk: Remove MP_PHY clocks resets and init logic
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18774
Signed-off-by: Robert Marko <robimarko@gmail.com>
The initial 6.12 merge leaves package/zram menuconfig behaviour confusing.
Selecting "kmod-zram" opens a submenu of the available algorithms to build
and the actual algo to use. However, when "lzo-rle" is shown as the default
used, it still remains missing from the available list. Only enabling a
_different_ compression algo to build will also reveal "lzo-rle" as
available.
Update the Kconfig to show "lzo-rle" as available if used/referenced.
Fixes: 4708057e27 ("package/zram: update for kernel 6.12")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/18712
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The driver tries to access ioports (0x2f9!!) which UML doesn't have.
This causes lots of warnings to appear on boot:
| WARNING: CPU: 0 PID: 1 at lib/logic_iomem.c:188 serial8250_config_port+0x20a/0x1260
| Invalid writeqb of 0xff at address 2f9
| Modules linked in:
| CPU: 0 UID: 0 PID: 1 Comm: swapper Tainted: G W 6.12.25 #0
| Tainted: [W]=WARN
| Stack:
| Call Trace:
| [<60001000>] ? set_reset_devices+0x0/0x16
| [<60452cba>] ? serial8250_config_port+0x20a/0x1260
| [<6071e91f>] ? dump_stack_lvl+0x55/0x71
| [<606e127c>] ? _printk+0x0/0x4f
| [<60044bbb>] ? __warn+0x11b/0x120
| [<6003b5d0>] ? um_set_signals+0x0/0x40
| [<606de721>] ? warn_slowpath_fmt+0x81/0x8c
| [<606de6a0>] ? warn_slowpath_fmt+0x0/0x8c
| [<60452cba>] ? serial8250_config_port+0x20a/0x1260
(they are even recursive!)
Now, the situation gets more confusing. Because from what I can tell,
this was seemingly done intenionally. Upstream patches in related areas:
|commit ddd268c42871b78c75e12a5c28207fb481138f41
|Author: Niklas Schnelle <schnelle@linux.ibm.com>
|Date: Wed Apr 3 14:43:00 2024 +0200
|
| um: Select HAS_IOREMAP for UML_IOMEM_EMULATION
|
| In a future patch HAS_IOPORT=n will disable inb()/outb() and friends at
| compile time. UML supports these via its UML_IOMEM_EMULATION so let that
| select HAS_IOPORT and also reflect this in NO_IOPORT_MAP.
hint that there's ongoing work in this area. But unfortunately, this future
hasn't arrived yet. Once this future arrives, please nuke this patch.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Currently, MaxLinear/Exar USB serial devices are supported via out-of-tree
usb-serial-xr_usb_serial_common driver which is broken on 6.12.
So since upstream has support for these devices since 6.5 lets package
the in-tree driver to be able to drop the out-of-tree one.
Link: https://github.com/openwrt/openwrt/pull/18926
Signed-off-by: Robert Marko <robimarko@gmail.com>
