Removed several EEPROM bit dependencies:
- for dt aliases that don't exist and thus don't ever do anything
(pcie,lvds1,uart*,vpu,csi*,hdmi_in,hdmi_out,cvbs_in,cvbs_out,gps)
- for features that don't effect bus ordering or have no detrimental affect
if erroneously enabled when not present (ahci,nand,i2c*)
- for features that have little to no impact on being erroneously enabled
but high impact if erroneously disabled (can*, spi*)
- for features that have an high adverse affect of not being set when they
should and no adverse affect of being set when they
shouldn't (ipu*).
Removing these means the following:
- these no longer are supported with the econfig command
- these no longer affect the device-tree in any way
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The MSATA feature is a board-specific feature on Gateworks Ventana boards.
In most cases a 2:1 mux will steer either PCIe or SATA to a miniPCIe socket
through an MSATA_EN gpio. In these such cases assign the gpio in the board
specific struct and use its presence to determine if we default the GPIO to
PCIe and if we later steer it according to hwconfig.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Most Ventana boards have a connector with off-board digital-I/O signals
including some that can be pinmuxed as either a PWM or a GPIO. The hwconfig
env variable is used to configure these and they will be pinmuxed according
to this configuration in the bootloader.
This patch adds a device-tree fixup that will enable the pwm controller
nodes appropriately for digital-I/O's that are configured as pwm via hwconfig
so that the pin can be used with the Linux kernel /sys/class/pwm API.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Calling request_gpio to register bklt_gpio with the GPIO driver had no effect
in setup_display called from early board init (although pinmuxing it and
configuring it as output-low does do what it should). Therefore move the
request_gpio later in enable_lvds so that its registered for use by the
gpio command if LVDS is actually enabled.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks System Controller on Ventana boards has the ability to
disable the board's primary power supply until the RTC hits a specific
time. When sleeping a button-down event on the GSC user pushbutton will
wake the board before it's wake time has been reached. This feature is
referred to as GSC sleep.
Add a command to invoke sleep mode for a specified number of seconds.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
If not booting Falcon mode, leave the boot watchdog enabled as a work-around
for other non-resolved bootloader hangs.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Allow L1 Icache & L1 Dcache line size to be specified separately, since
there's no architectural mandate that they be the same. The
[id]cache_line_size functions are tidied up to take advantage of the
fact that the Kconfig entries are always present to simply check them
for zero rather than needing to #ifdef on their presence.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
[removed CONFIG_SYS_CACHELINE_SIZE in include/configs/pic32mzdask.h]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Move details of the L1 cache line sizes & total sizes into Kconfig,
defaulting to 0. A new CONFIG_SYS_CACHE_SIZE_AUTO Kconfig entry is
introduced to allow platforms to select auto-detection of cache sizes,
and it defaults to being enabled if none of the cache sizes are set by
the configuration (ie. sizes are all the default 0), and code is
adjusted to #ifdef on that rather than on the definition of the sizes
(which will always be defined even if 0).
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Both real Malta boards & emulators that mimic Malta (eg. QEMU) can
support MIPS64 CPUs. Allow MIPS64 builds of U-Boot for such boards,
which enables the user to make use of the whole 64 bit address space.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
As the old ethernet PHY is not available any more, the x600 board has
been redesigned with the Micrel KSZ9031 PHY. This patch adds support
to autodetect the PHY and configure the Micrel PHY correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Different AM335x based platforms have different serial consoles. As serial
console is Kconfig option a separate defconfig has to be created for each
platform. So pass the serial device dynamically.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add minimal dts support for AM335x-ICEv2 board
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
In order to enable cpsw on AM335x ICEv2 board, the following needs to be done:
1)There are few on board jumper settings which gives a choice between
cpsw and PRUSS, that needs to be properly selected[1]. Even after selecting
this, there are few GPIOs which control these muxes that needs to be held high.
2) The clock to PHY is provided by a PLL-based clock synthesizer[2] connected
via I2C. This needs to properly programmed and locked for PHY operation.
And PHY needs to be reset before before being used, which is also held by
a GPIO.
3) RMII mode needs to be selected.
[1] http://www.ti.com/lit/zip/tidr336
[2] http://www.ti.com/lit/ds/symlink/cdce913.pdf
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM335x ICEv2 contains a 2Gbit(128Mx16) of DDR3 SDRAM(MT41J128M16JT-125),
capable of running at 400MHz. Adding this specific DDR configuration
details running at 400MHz.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Similar to other TI's AM335x platforms, AM335x ICEv2 also has an
eeprom populated for its unique identification. Adding this info
so that AM335x ICEv2 specific initialization can be done.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Use a single defconfig for all AM335x platforms by enabling FIT
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
FIT allows for a multiple dtb in a single image. SPL needs a way to
detect the right dtb to be used. Adding support for the same.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Use a single defconfig for all AM43xx platforms by enabling FIT and delete
the platform specific defconfigs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
FIT allows for a multiple dtb in a single image. SPL needs a way to
detect the right dtb to be used. Adding support for the same.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Removing:
uart3_defconfig:
Now uart3 can be selected using menuconfig, removing separate
config for uart mode. Doing uart boot is not straight forward as ROM uses
uart3 as default serial console. In order to boot to prompt, concole in both
u-boot and kernel needs to be changed.
qspiboot_defconfig:
The only advantage of enabling QSPI_BOOT is selecting env in QSPI.
Eventually env needs to be selected by menuconfig so removing
qspiboot_defconfig. qspiboot can be done using dra7xx_evm_defconfig.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Use a single defconfig for all DRA7 platforms by enabling FIT and delete
the platform specific defconfigs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
FIT allows for a multiple dtb in a single image. SPL needs a way to
detect the right dtb to be used. Adding support for the same.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Adds the board specific ft_board_setup() functions that
are called when CONFIG_OF_BOARD_SETUP is defined. These functions
will currently just call the ft_cpu_setup() function.
Adds CONFIG_OF_BOARD_SETUP to the defconfig files
for dra72_evm, dra74_evm, and am57xx_evm.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adds code to detect AM43xx HS EVMS - the string in the
I2C EEPROM for HS EVMs differs from GP EVMs. Adds code to
for evm detection, regardless of whether the evm is for
GP or HS parts, and updates board init to use that.
Modifies findfdt command to pick up am437x-gp-evm.dtb for
the HS EVMs also, as the boards are similar except for
some security specific changes around power supply and
enclosure protection.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Daniel Allred <d-allred@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Since CONFIG_OF_BOARD_SETUP depends on CONFIG_OF_LIBFDT:
config OF_BOARD_SETUP
bool "Set up board-specific details in device tree before boot"
depends on OF_LIBFDT
...
remove superfluous tests of CONFIG_OF_LIBFDT when testing for
CONFIG_OF_BOARD_SETUP.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
[trini: Typo fix: s/ifdefi/ifdef/]
Signed-off-by: Tom Rini <trini@konsulko.com>
With dropping support for some boards and the deletion of some source
files, it appears that both of these directories are now superfluous.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
This includes the following fixes:
- Define needed __init_end symbol - see initr_reloc_global_data()
- Drop SH-specific struct bd_info
- Add an empty relocate_code() function
This prevents build errors with generic board, but the code will still need
work. Perhaps this is a better alternative than deleting the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove the warning from the Makefile, since boards that do not use generic
board will no longer build. Also update documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
This adds platform code for the Amlogic Meson GXBaby (S905) SoC and a
board definition for ODROID-C2. This initial submission only supports
UART and Ethernet (through the existing Designware driver). DTS files
are the ones submitted to Linux arm-soc for 4.7 [1].
[1] https://patchwork.ozlabs.org/patch/603583/
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move CONFIG_SYS_TEXT_BASE to Kconfig, and add default values in board
Kconfig files matching what was present in their config headers. This
will make it cleaner to conditionalise the value for Malta based on 32
vs 64 bit builds.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
The address of the UART differs based upon the system controller because
it's actually within the I/O port region, which is in a different
location for each system controller. Rather than handling this as 2
UARTs with the correct one selected at runtime, use I/O port accessors
for the UART such that access to it gets translated into the I/O port
region automatically.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Recently a set of CONFIG_CMD_FOO defines was moved from being defined
in config_distro_defaults to Kconfig, and added to all sunxi defconfigs
to compensate.
Instead of explictly selecting these in all sunxi defconfigs,
simply always select these for sunxi boards. This makes the defconfigs
simpler and ensures a consistent set of available commands across all
sunxi boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The ARM Trusted Firmware (ATF) code now lives in SRAM on the Pine64/A64,
so we can claim the whole of DRAM for OS use.
This reverts commit 3ffe39ed2b.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The A80 uses the AXP809 as its primary PMIC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The AXP818 has a switchable output, SW. This is commonly used for
controlling power to the LCD backlight.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The newer chips use a newer display pipeline, which is not supported.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
A83T, H3, and A64 have a dedicated pin for card detect on the PF
pingroup. This is used in all designs. Set it as the default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
In most other places, we sort SoC descriptions by family (sunXi) first,
then by the chip name (A20).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The user should always select an SoC variant to support. Not choosing
one doesn't make sense for a bootloader.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Now that we are using driver model, we can drop the weak functions and LCD
init in the board file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Update several boards to use driver model for video. This involves changes
to the EDP and FIMD (frame buffer) drivers. Existing PWM, simple-panel and
pwm-backlight drivers are used. These work without additional configuration
since they use the device tree settings in the same way as Linux.
Boards converted are:
- snow
- spring
- peach-pit
- peach-pi
All have been tested. Not converted:
- MIPI display driver
- s5pc210_universal
- smdk5420
- smdk5250
- trats
- trats2
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This function controls enabling the EDP PHY. Rename it and drop the existing
weak functions, which are confusing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Some boards have the LCD enabled but I cannot test operation for the driver
model conversion. Disable the LCD on these to avoid build errors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This file currently requires LCD support. Adjust it so that it can still be
built without LCD support (even thought it won't work fully).
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Espresso7420 is a development/evaluation board for Exynos7420 SoC. It
includes multiple onboard compoments (EMMC/Codec) and various
interconnects (USB/HDMI).
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Disable the non-existent ethernet ports on T4240RDB:FM1_DTSEC5,
FM1_DTSEC6, FM2_DTSEC5 and FM2_DTSEC6.
Signed-off-by: Ying Zhang <ying.zhang22455@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <york.sun@nxp.com>
NAND+MMC env support costs 12KB in the SPL which is fairly expensive just
for the ability to specify whether or not to boot to uboot or directly
to linux. The Ventana boards have plenty of EEPROM storage so we will use
a byte there to signify if we should boot to the bootloader or to the OS.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Extending Kconfig for adding new platform is a lot of work
for nothing. Setting SYS_CONFIG_NAME directly in Kconfig and
remove all dependencies on TARGET_ZYNQ_* options including SPL.
As a side-effect it also remove custom init folder for ps7_init_gpl.*
files. Folder is chosen based on device-tree file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Support RAM and MMC boot mode in SPL also with SPL_FIT images.
In MMC boot mode two boot options are available:
1) Boot flow with ATF(EL3) and full U-Boot(EL2):
aarch64-linux-gnu-objcopy -O binary bl31.elf bl31.bin
mkimage -A arm64 -O linux -T kernel -C none -a 0xfffe5000 -e 0xfffe5000
-d bl31.bin atf.ub
cp spl/boot.bin <sdcard fat partition>
cp atf.ub <sdcard fat partition>
cp u-boot.bin <sdcard fat partition>
2) Boot flow with full U-Boot(EL3):
cp spl/boot.bin <sdcard>
cp u-boot*.img <sdcard>
3) emmc boot mode
dd if=/dev/zero of=sd.img bs=1024 count=1024
parted sd.img mktable msdos
parted sd.img mkpart p fat32 0% 100%
kpartx -a sd.img
mkfs.vfat /dev/mapper/loop0p1
mount /dev/mapper/loop0p1 /mnt/
cp spl/boot.bin /mnt
cp u-boot.img /mnt
cp u-boot.bin /mnt
cp atf.ub /mnt
umount /dev/mapper/loop0p1
kpartx -d sd.img
cp sd.img /tftpboot/
and program it via u-boot
tftpb 10000 sd.img
mmcinfo
mmc write 10000 0 $filesize
mmc rescan
mmc part
ls mmc 0
psu_init() function contains low level SoC setup generated for every HW
design by Xilinx design tools. xil_io.h is only supporting file to fix
all dependencies from tools. The same solution was used on Xilinx Zynq.
The patch also change CONFIG_SYS_INIT_SP_ADDR to the end of OCM which
stays at the same location all the time.
Bootrom expects starting address to be at 0xfffc0000 that's why this
address is SPL_TEXT_BASE.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for on board eeprom with programmed MAC for using in u-boot
to have uniq address for every board.
Most of the time uniq MAC address is on a label on the board.
If address is not programmed use these command to program it.
On zcu102:
ZynqMP> mm.b 0
00000000: 00 ? 00
00000001: a0 ? 0a
00000002: 35 ? 35
00000003: 02 ? 02
00000004: 00 ? ef
00000005: 00 ? 67
00000006: 00 ? q
i2c dev 5
i2c write 0 54 20 6
i2c md 54 20
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change the clock source of the SDHCI's generated clock from PLLA to
UPLL clock to align to Linux driver.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Fix the missing pin config of the SDMMC0 interface.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
The board supports following features:
- Boot media support: NAND Flash/SPI Flash
- Support ethernet
- Support USB mass storage
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Override the default product name U-Boot reports in the SMBIOS
table, to be compatible with the Intel provided UEFI BIOS, as
Linux kernel drivers (drivers/mfd/intel_quark_i2c_gpio.c and
drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c) make use of
it to do different board level configuration.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Let git ignore dsdt.aml, dsdt.asl.tmp and dsdt.c files.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable ACPI table generation by creating a DSDT table for all baytrail
boards: conga-qeval20-qa3-e3845, bayleybay and minnowmax.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
We always build for a mips32 or higher ISA, so this ".set mips32"
directive is redundant. Once MIPSr6 support is added it will become
harmful since some instruction encodings change & this directive will
cause the older encodings to be incorrectly emitted instead of the
appropriate ones for the build.
In preparation for supporting MIPSr6, remove this redundant directive.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Add support for the TPLink WDR4300 router, which is based on the
AR9344 MIPS 74Kc CPU and has 128 MiB of RAM. The USB is supported
on this system as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Wills Wang <wills.wang@live.com>
This patch add board-level code and base DT for AP143.
Signed-off-by: Wills Wang <wills.wang@live.com>
[updated defconfig, enabled CONFIG_USE_PRIVATE_LIBGCC=y]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch add board-level code and base DT for AP121.
Signed-off-by: Wills Wang <wills.wang@live.com>
[updated defconfig, enabled CONFIG_USE_PRIVATE_LIBGCC=y]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add layout definitions and implement functions for field printing/updating,
layout detection, layout assignment, and layout parsing.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
To use AQR105 PHY's interrupt, we need to invert the IRQ pin polarity
by setting relative bit in SCFG_INTPCR register, because AQR105
interrupt is low active but GIC accepts high active.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Some SOCs, specifically the ones in the C29x familiy can have
multiple security engines. This patch adds a system configuration
define which indicates the maximum number of SEC engines that
can be found on a SoC.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Using u16 for cfg_rcw_src and u8 for sd1refclk_sel is enough.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
gd->env_addr will be initialized in env_init() in
common/env_nowhere.c if CONFIG_ENV_IS_NOWHERE is defined.
So no need to do it again.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The current 'cpld reset' will just write global_rst register
but couldn't switch to NOR boot if the board's switches are
for NAND/SD boot. So need to write rcw source registers for
NOR boot as well.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Mix usage of uint32_t and u32 fixed in favor of u32.
Signed-off-by: Vincent Siles <vincent.siles@provenrun.com>
Reviewed-by: York Sun <york.sun@nxp.com>
On the LS102x boards, in order to initialize the ICID values of
masters, the dev_stream_id array holds absolute offsets from the
base of SCFG.
In ls102xa_config_ssmu_stream_id, the base pointer is cast to
uint32_t * before adding the offset, leading to an invalid address.
Casting it to void * solves the issue.
Signed-off-by: Vincent Siles <vincent.siles@provenrun.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Update MAINTAINERS file for ls2080aqds and ls2080ardb platforms.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Optimize DDR timing for good margins to support new Transcend
and Apacer DDR4 UDIMM besides current Micron UDIMM.
Verified 1333MT/s, 1600MT/s, 1866MT/s, 2133MT/s rate with
following UDIMM on LS2080ARDB.
- Micron UDIMM: MTA18ASF1G72AZ-2G1A1Z
- Apacer UDIMM: 78.C1GM4.AF10B
- Transcend UDIMM: TS1GLH72V1H
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Barrier transactions from CCI400 need to be disabled till
the DDR is configured, otherwise it may lead to system hang.
The patch adds workaround to fix the erratum.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This option currently enables both the command and the SCSI functionality.
Rename the existing option to CONFIG_SCSI since most of the code relates
to the feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
While the driver-model block device support is in progress, it is useful to
build sandbox both with and without CONFIG_BLK. Add a separate board for
the latter.
Signed-off-by: Simon Glass <sjg@chromium.org>
This imports v11 of "Jetson TK1 Development Platform Pin Mux" from
https://developer.nvidia.com/embedded/downloads.
The new version defines the mux option for the MIPI pad ctrl selection.
The OWR pin no longer has an entry in the configuration table because
the only mux option it support is OWR, that feature isn't supported, and
hence can't conflict with any other pin. This pin can only usefully be
used as a GPIO.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
ABB should be initialized for all required domains voltage domain
for DRA7: IVA, GPU, EVE in addition to the existing MPU domain. If
we do not do this, kernel configuring just the frequency using the
default boot loader configured voltage can fail on many corner lot
units and has been hard to debug. This specifically is a concern with
DRA7 generation of SoCs since other than VDD_MPU, all other domains
are only permitted to setup the voltages to required OPP only at boot.
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
ABB TX_DONE mask will vary depending on ABB module. For example,
3630 never had ABB on IVA domain, while OMAP5 does use ABB on MM domain,
DRA7 has it on all domains with the exception of CORE, RTC.
Hence, move the txdone mask definition over to structure describing
voltage domain.
Signed-off-by: Nishanth Menon <nm@ti.com>
This patch updates and simplifies the hikey README. The old
instructions were hard to follow, and convoluted.
This patch also updates the link to the mcuimage.bin which was outdated.
Using an outdated mcuimage.bin results in the additional a53 cores
not coming online when the kernel issues PSCI requests to
arm trusted firmware (ATF).
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The memory node gets automatically generated by U-Boot
in arch_fixup_fdt(), before passing control to the kernel
using U-Boots representation of the dram banks.
However the upstream kernel uses the memory node to carve-out
regions of RAM for various purposes. To make this work without
changing arch_fixup_fdt() which will effect many platforms
we replicate the upstream memory node layout using the dram
banks.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Currently only the serial pl01x driver is using DT,
and the other drivers still use platform data but
as more DT lands in the upstream kernel the aim is
to migrate the other drivers over to DT as well to
have a fully DT configured hikey u-boot.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds myself as maintainer for the hikey
U-Boot port.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for Technexion's PICO-IMX6UL-EMMC board.
For information about this board, please visit:
http://www.technexion.com/products/pico/pico-som/pico-imx6-emmc
Signed-off-by: Richard Hu <richard.hu@technexion.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
On a reset/reboot, the display power needs to be off for atleast 500ms
before turning it back on. So add a delay to the boot process to meet
the display timing requirement.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>
To generate accurate pixel clocks required by the displays we need to
set the ldb_di_clk source on bx50v3 to PLL3 and b850v3 to PLL5. Since
PLL5 is disabled on reset, we need to enable PLL5.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>
B450v3/B650v3 uses single channel LVDS and does not support HDMI.
B850v3 uses dual channel LVDS and supports HDMI. Hence split the display
setup into two different functions.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>
Certain pins are not used on the i.MX6, and should have a neutral
pad configuration in order to reduce electrical interference on
the board. This commit defines these pins with a default value
rather than relying on the system defaults.
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Cc: Stefano Babic <sbabic@denx.de>
Apparently, all "dave"-related vendor content was removed in commit
5344cc1a82fcc2817d4671696b3939b0dfa4323e; remove remaining directory
board/dave/, which consists solely of board/dave/common/flash.c.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Not all Keystone2 devices has AEMIF NAND controller. So adding Kconfig
entry for CONFIG_TI_AEMIF and enabling it in respective defconfigs on
platforms with AEMIF controller.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The AM572x-IDK board (Industrial Dev Kit) is a board based on TI's AM5728x
SOC which has a dual core 1.5GHz A15 processor. This board is a development
platform for the Industrial market with:
- 2GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI,
- PRU-ICSS
- uSD
- 16GB eMMC
- CAN
- RS-485
- PCIe
- USB3.0
- Video Input Port
- Industrial IO port and expansion connector
The link to the data sheet and TRM can be found here:
http://www.ti.com/product/AM5728
NOTE: DT support is still pending upstream kernel acceptance but we
should be able to get the base system support with this patch.
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update EMIF data based on recommendations from the now standard TI
EMIF tool version 1.1.1 based on 256MBx16 DDR3L Kingston D2516EC4BXGGB
data sheet
Update T_RRD from 5 to 6 based on AM57xx TRM -
Minimum number of DDR cycles from activate to ativate for a different
bank, minus 1.
Update T_CKESR from 4 to 3 based on AM57xx TRM - Minimum number of DDR
clocks cycles for which SDRAM must remain in self refresh, minus 1.
Signed-off-by: Schuyler Patton <spatton@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
- Move the CONS_INDEX selection out of CONFIG_SYS_EXTRA_OPTIONS and
into Kconfig proper.
- Edit the relevant am57x configs to remove the now unneeded
CONFIG_SYS_EXTRA_OPTIONS.
Signed-off-by: Daniel Allred <d-allred@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update dm test command with pytest instead of ./test/dm/test-dm.sh
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Including netdev.h is causing compilation warning:
+ int fecmxc_register_mii_postcall(struct eth_device *dev, int
(*cb)(int));
+ ^
w+In file included from ../board/xilinx/zynqmp/zynqmp.c:9:0:
w+../include/netdev.h:204:41: warning: ‘struct eth_device’ declared
inside parameter list [enabled by default]
w+../include/netdev.h:204:41: warning: its scope is only this definition
or declaration, which is probably not what you want [enabled by default]
This patch removes it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define u64 types to be usable on 32bit system because of 64bit address
and size cells and 32bit shifts in the code.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This line is not needed, as the board supports DT based probing. And
here the "Model:" is already printed:
Model: Marvell Armada XP theadorable
Board: theadorable
One line for the board name is enough.
Signed-off-by: Stefan Roese <sr@denx.de>
Sometimes the PCIe link for the PEX-switch will not come-up. In this case,
the board is not in a usable state. This patch makes sure that in this
case a soft-reset is issued. If this soft-reset does not result in the
PEX-switch being detected after some soft-reset cycles, an I2C message
is sent to the uC to issue a complete power-cycle of the board.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds an USB power toggle for theadorable. Additionally, the
USB PHY RX Channel Control 0 Register is changed to fix some issues
noticed while accessing some specific USB sticks.
Signed-off-by: Stefan Roese <sr@denx.de>
The Orange Pi One SBC, is a stripped down version of the popular
Orange Pi PC. The one is a H3 based SBC, with 512M of RAM,
micro-sd slot, 1 host usb, 1 otg usb, hdmi and 100Mbit ethernet.
The dts is identical to the dts submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Some boards have on board usb devices which need longer than the USB
spec's 1 second to connect from board powerup. Add a config option which
when non 0 adds an extra delay before the first usb bus scan.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Now that rpi_*defconfig and Kconfig (rather than the config header file)
provide the identity of the build, we don't need to separate config
headers and board directories for each RPi variant. Set CONFIG_SYS_BOARD
and CONFIG_SYS_CONFIG_NAME so that we can get rid of the duplication. This
requires a tiny number of extra ifdefs in the config header.
The only disadvantage of this approach is that the $board/$board_name
environment variables aren't as descriptive as they used to be. This isn't
really an issue because those only exist to allow scripts to create DTB
filenames at runtime. However, the RPi board code already sets $fdtfile to
something more accurate based on FW-reported board ID anyway.
While at it, unify some Kconfig select options, and add a MAINTAINERS
entry for bcm283x too.
Partially-suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
init_sata() is done as part of scsi_init() in
arch/arm/cpu/armv7/omap-common/sata.c so no need to duplicate
it here.
This seems to fix SATA problems in the kernel when CONFIG_TI_PIPE3 is
configured as loadable module.
Cc: Cooper Jr., Franklin <fcooper@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
On all Pis so far, the VC FW provides a short stub to set up the ARM CPU
before entering the kernel (a/k/a U-Boot for us). This feature is not
currently supported by the VC FW when booting in 64-bit mode. However,
this feature will likely appear in the near future, and this U-Boot port
assumes that such a feature is in place. Without that feature, or a
temporary workaround described below, U-Boot will not boot.
Once the VC FW does provide the ARM stub, u-boot.bin built for rpi_3 can
be used drectly as kernel7.img, in the same way as any other RPi port. The
following config.txt is required:
# Fix mini UART input frequency, and setup/enable up the UART.
# Without this option, U-Boot will not boot, even if you don't care
# about the serial console. This option will always be required for
# all RPi3 use-cases, unless the PL011 UART is used, which is not
# yet supported by rpi_3* builds of U-Boot.
enable_uart=1
# Boot in AArch64 (64-bit) mode.
# It is possible that a future VC FW will remove the need for this
# option, instead auto-setting 32-/64-bit mode based on the "kernel"
# filename present on the SD card.
arm_control=0x200
Prior to the VC FW providing the ARM boot stub, you can use the following
steps to build an equivalent stub into the U-Boot binary:
git clone https://github.com/swarren/rpi-3-aarch64-demo.git \
../rpi-3-aarch64-demo
(cd ../rpi-3-aarch64-demo && ./build.sh)
Build U-Boot for rpi_3 in the usual way
cat ../rpi-3-aarch64-demo/armstub64.bin u-boot.bin > u-boot.bin.stubbed
Use u-boot.bin.stubbed as kernel7.img on the Pi SD card.
In this case, the following additional entries are required in config.txt:
# Tell the FW to load the kernel image at address 0, the reset vector.
kernel_old=1
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The currently present DRAM timings generated from GHRD 14.0 did
not work on SoCkit rev. D because they were too tight. Load the
DRAM timings from GHRD 13.0 which are more relaxed and work with
SoCkit rev. D.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
LS2080A is the primary SoC, and LS2085A is a personality with AIOP
and DPAA DDR. The RDB and QDS boards support both personality. By
detecting the SVR at runtime, a single image per board can support
both SoCs. It gives users flexibility to swtich SoC without the need
to reprogram the board.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
When setting fixed-link property to DTS, the values should be converted
with using cpu_to_fdt32 so that to have correct value on little endian
Soc.
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
