Add the appropriate itapdly and clkbuf-sel values required for
some lower speed modes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Add support for UHS modes by adding the regulators to power cycle
and voltage switch the card. Also add pinmuxes required for each
node
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Add support for regulators to power cycle and switch IO voltage to the
SD card. This enables support for UHS modes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Update otap delay values to match with the latest Data Manual[1].
[1] https://www.ti.com/lit/gpn/dra829v
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Because of fundamental interface issues in am65x pg1, only the
initial sdhci1 node at 25 MHz was added in the u-boot.dtsi
from which both the base-board.dts and r5-base-board.dts
inherit the node. Move the node out to k3-am65-main.dtsi
where it belongs and add the board specific properties
in base-board.dts and r5-base-board.dts
This ensures dts compatibility with the kernel dts in the
base-board.dts and enables the SD card interface at 50 MHz
and High Speed mode
While we are here, also fix the main_mmc0_pins_default
property to be included and inherit from the base-board.dts
instead of the u-boot.dtsi
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
The K3 R5F remoteproc driver in U-Boot was upstreamed prior to the
equivalent remoteproc driver in the Linux kernel. Some of the DT
properties used in U-Boot got upstreamed using different names
in Linux kernel.
The modified property names include the R5F cluster mode configuration
property "lockstep-mode"; and three different individual R5F core config
properties - "atcm-enable", "btcm-enable" and "loczrama". The property
names were updated as follows:
lockstep-mode => ti,cluster-mode
atcm-enable => ti,atcm-enable
btcm-enable => ti,btcm-enable
loczrama => ti,loczrama
Update the K3 R5F remoteproc driver, the corresponding binding, and
all the existing usage in AM65x, J721E and J7200 dts files all at
once to use the new properties and to not break any bisectability.
Signed-off-by: Suman Anna <s-anna@ti.com>
No version information is used in armv8/fwcall.c therefore do not include
version.h header file. This change prevents recompiling fwcall.o when
SOURCE_DATE_EPOCH changes.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enhance the debugging to show the next stage being booted as well as a
dump of the start of the image.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This should be done even if not using TPL, since BSS may be in use or
boards that only use SPL. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present if the command line is very long it is truncated by the
printf() statement, which works within a limited buffer. Use puts()
instead. Also show better debugging with the command-line setup
fails.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present it is possible to dump an image within the zimage command, but
it is also useful to be able to dump it from elsewhere, for example in a
loader that has special handling for the different zimage stages.
Export this feature as a new function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Global Non-Volatile Storage struct has some fields with particular
meanings. Rename these to make things easier to follow. Also add a few
more boot flags.
GNVS should not be confused with GNVQ (Going Nowhere Very Quickly).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present BSS is always placed in SDRAM. If a separate BSS is not in use
this means that BSS doesn't work as expected. Make the setting conditional
on the SEPARATE_BSS option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The part of U-Boot that actually ends up in u-boot-nodtb.bin is not built
with any particular alignment. It ends at the start of the BSS section.
The BSS section selects its own alignment, which may larger.
This means that there can be a gap of a few bytes between the image
ending and BSS starting.
Since u-boot.bin is build by joining u-boot-nodtb.bin and u-boot.dtb (with
perhaps some padding for BSS), the expected result is not obtained. U-Boot
uses the end of BSS to find the devicetree, so this means that it cannot
be found.
Add 32-byte alignment of BSS so that the image size is correct and
appending the devicetree will place it at the end of BSS.
Example SPL output without this patch:
Sections:
Idx Name Size VMA LMA File off Algn
0 .text 000142a1 fef40000 fef40000 00001000 2**4
CONTENTS, ALLOC, LOAD, RELOC, READONLY, CODE
1 .u_boot_list 000014a4 fef542a8 fef542a8 000152a8 2**3
CONTENTS, ALLOC, LOAD, RELOC, DATA
2 .rodata 0000599c fef55760 fef55760 00016760 2**5
CONTENTS, ALLOC, LOAD, RELOC, READONLY, DATA
3 .data 00000970 fef5b100 fef5b100 0001c100 2**5
CONTENTS, ALLOC, LOAD, RELOC, DATA
4 .binman_sym_table 00000020 fef5ba70 fef5ba70 0001ca70 2**2
CONTENTS, ALLOC, LOAD, DATA
5 .bss 00000060 fef5baa0 fef5baa0 00000000 2**5
ALLOC
You can see that .bss is aligned to 2**5 (32 bytes). This is because of
the mallinfo struct in dlmalloc.c:
17 .bss.current_mallinfo 00000028 00000000 00000000 000004c0 2**5
ALLOC
In this case the size of u-boot-spl-nodtb.bin is 0x1ba90. This matches up
with the _image_binary_end symbol:
fef5ba90 g .binman_sym_table 00000000 _image_binary_end
But BSS starts 16 bytes later, at 0xfef5baa0, due to the 32-byte
alignment. So we must align _image_binary_end to a 32-byte boundary. This
forces the binary size to be 0x1baa0, i.e. ending at the start of bss, as
expected.
Note that gcc reports __BIGGEST_ALIGNMENT__ of 16 on this build, even
though it generates an object file with a member that requests 32-byte
alignment.
The current_mallinfo struct is 40 bytes in size. Increasing the struct to
68 bytes (i.e. just above a 64-byte boundary) does not cause the alignment
to go above 32 bytes. So it seems that 32 bytes is the maximum alignment
at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add more details in the commit message to help people understand]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Move to log_debug() and make use of the new SPL function to find the
text base.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use a driver name in line with the compatible string so that of-platdata
can use this driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a node for this so we can indicate that it is does not require any
ACPI code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
binman fixes support for symbols in sub-sections
support for additional cros_ec commands
various minor fixes / tweaks
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmAV6K8RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYERgf/QbwOL87yPbf9SyXBQ0EMTmn1ve9HCiv9
yeXrijvA0/wtTVoM44d/z7THb+7Zqw6LbsVOXUSicdGqaogy10xIuz5we0CoGJm6
iwYWV6kaAqjCxDTlSToGnR/TCjiOVgXC6u5QPCZC0LGbAmDbAl4jyCuQxxq2eXYD
hrLSzZPHDe0s2BeWZKRQJ26qyPfWIribXNJXG78/FsvDrdWPPc5K+/ZEb2IWawWR
nEZ8GTEYZpik/niEJ3gFozwCwpJQi3PyukjZvzTGn6tBqg12YXE4dbSzcj48Uj4o
prwUFAGKRR97zFB6c4+NUvd3VBUgPtPdZrtzZ1nNCppiMq1E4BKiDg==
=kijh
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-30jan21' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
tpm fixes for coral
binman fixes support for symbols in sub-sections
support for additional cros_ec commands
various minor fixes / tweaks
DTS files apart from r8a774a1-hihope-rzg2m-u-boot.dts and
r8a774a1-u-boot.dtsi have been imported from linux 5.10
commit 2c85ebc57b3e1817 ("Linux 5.10").
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
The UEFI Self Certification Test (SCT) checks the SetTime() service with
the following steps:
* set date
* reset
* check date matches
To be compliant the sandbox should keep the offset to the host RTC during
resets. The implementation uses the environment variable
UBOOT_SB_TIME_OFFSET to persist the offset.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present this function uses the old format for reading hashes. Add
support for the current format.
Add a test while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
These cannot work with of-platdata since they currently need the
devicetree at runtime. Disable the emulators and the sandbox I2C driver
that needs them. We can enable these later, if needed for testing.
Switch the of_plat_parent test over to use a simple bus instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Update the devicetree so that the TPM and RTC can be used in SPL. Also
enable the pins used for getting the memory configuration settings while
we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
On x86 platforms the EC provides a way to read 'switches', which are
on/off values determined by the EC.
Add a new driver method for this and implement it for LPC.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is used several times in this file. Put it in a function to avoid
code duplication.
Also add a test for this function. There are no cros_ec tests at present,
so it is time to update the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add the Linux magic to the EFI file header to allow running our test
programs with GRUB's linux command. Now we can dump the fixed-up device
tree with our dtbdump.efi tool.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
1. Enable MTK SPI NOR controller driver on mt7622 & mt7629.
2. Enable quad mode for read and single mode for write.
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
- Espressobin: Disable slot when emmc is not present (Pali)
- DS414; config header cleanup (Phil)
- PCI: auto-config enhancement (Phil)
- pci_mvebu: Also map IO region (Phil)
- serial: a3720: Implement pending method for output direction (Pali)
- turris_mox: Enable a few commands (Marek)
- helios4 & ClearFog changes (Dennis)
- Plus some minor misc changes
Add CAxxxx Ethernet support for the Cortina Access
Presidio Engineering Board
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Tom Rini <trini@konsulko.com>
Move all aliases defintions into the main dts file
Add u-boot definiton to i2c0 based on clearfog
set spi1 status to okay
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
OrangePi Zero2 is SBC based on Allwinner H616 with 1 GiB of RAM, SD card
support, gigabit ethernet, micro HDMI, WIFI, Bluetooth and 1 USB 2.0
port. It also has two GPIO headers which allows further peripherals to
be used.
The devicetree file is taken from v3 of the OrangePi Zero2 Linux
submission [1], which it's not yet merged.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/632084.html
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This commit introduces H616 DTSI file and dt-bindings headers needed for
device tree files.
Files are taken from v3 Linux H616 support submission[1], as the
H616 .dtsi file is not merged upstream yet.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2021-January/632082.html
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
H616 uses different address for reset. Add it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
H616 is very similar to H6 so most of the infrastructure can be reused.
However, two big differences are that it doesn't have functional SRAM A2
which is usually used for TF-A and it doesn't have ARISC co-processor.
It also needs bigger SPL size - 48 KiB.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Allwinner H616 supports many types of DRAM. Most notably it supports
LPDDR4. However, all commercially available boards at this time use
only DDR3, so this commit adds only DDR3 support.
Controller and MBUS are very similar to H6 but PHY is completely
unknown.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This port is needed for communication with PMIC. SPL uses it to set DRAM
voltage on H616 boards.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This port is used for debug terminal on all known H616 boards.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
H616 has mostly the same clocks as H6 with some small differences. Just
reuse H6 clocks for H616 and handle differences with macros.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
H616 supports and needs bigger SPL than 32 KiB, mostly due to big DRAM
driver and need for PMIC configuration, which pulls several drivers which
are not needed otherwise.
spl_mmc_get_uboot_raw_sector() will now compare pre-configured size with
that, reported in SPL header. If size in header is bigger, it will use
that value instead.
In the process of function rework, also add missing function argument.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
I2C support, especially R_I2C port, will be needed in future. Upcoming
support for H616 will need R_I2C to adjust DRAM voltage.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
There was no need to have prcm definitions for H6 and similar SoCs till
now. However, support R_I2C will be needed soon in SPL.
Move old definitions to prcm_sun6i.h and add new ones in prcm_sun50i.h.
One of those files will be selected in common prcm.h based on defined
macros.
This commit doesn't do any functional change.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
It turns out that several SoCs share same mmc configuration as H6. In
order to lower ifdef clutter replace H6 specific macro with common one.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
It turns out that there are at least 2 other SoCs which have basically
the same memory map, similar clocks and other features as H6. It's very
likely that we'll see more such SoCs in the future. In order to ease
porting to new SoCs and lower ifdef clutter, introduce common symbol for
them.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
