Use a generic default topology if we cannot infer switch information from
board.json and display an error message in this case. Should fix#779 and
similar issues.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Gracefully handle a missing diag section in /etc/config/luci when rendering
the network diagnostics tool page.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
When a wireless network is disabled it can't be removed. From
wifi_overview.htm the delete call is generated as wlan0, wlan1 or
whatever. This wlan is not working because it is disabled, then LuCI
deletes the virtual radio which really is named as wlan0.
Replace the menu item "Wifi" by "Wireless",
which is already used for page and section headings
This closes#695
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
This pull request adds a condition, which checks whether the file "/etc/config/fstab" exists before it allows access to "mount points".
Signed-off-by: Guido Lipke <lipkegu@gmail.com>
Add support for dnsmasq uci options 'quietdhcp' and 'sequential_ip'
(disable logging, allocate ip addresses sequentially)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
This patch fixes the wrong visualization of Noise Margin (SNR) and Signal Attenuation (SATN) stats
Signed-off-by: Luca Debernardi <luca.debernardi@gmail.com>
Fix dhcpv6 ra_management option's handling of "stateless" value.
Default value for the option is 1, so trying to store ""
instead of "0" for stateless is not working.
This fixes#676
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
- Under some conditions the system will shutdown
uhttpd before the page will be delivered to
the client. Waiting one second should eleminate
this behaviour.
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
When kmod-nf-nat6 and kmod-ipt-nat6 are installed, the firewall has also
the 'nat' table for ipv6, and packages like 'adblock' utilize that table.
Currently that table is not shown on the Luci firewall status page,
although it is visible by 'ip6tables -L -v -t nat' from console.
Detect 'nat' table's presence from /proc/net/ip6_tables_names
Show 'nat' table in Status->Firewall->IPv6 if that table is present.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
This adds a lot of new status information about the dsl line.
It now looks like this on a Telekom line:
Status: UP
Line State: showtime_tc_sync [0x801]
Line Mode: G.993.2 (VDSL2)
Annex: B
Profile: 17a
Data Rate: 51.391 Mb/s / 10.046 Mb/s
Max. Attainable Data Rate (ATTNDR): 63.817 Mb/s / 23.908 Mb/s
Latency: 4.0 ms / 8.0 ms
Line Attenuation (LATN): 10.5 dB / 9.9 dB
Signal Attenuation (SATN): 8.2 dB / 14.4 dB
Noise Margin (SNR): 10.5 dB / 9.7 dB
Aggregate Transmit Power(ACTATP): -14 dB / 12.4 dB
Forward Error Correction Seconds (FECS): 1 / 1723485
Errored seconds (ES): 0 / 2477
Severely Errored Seconds (SES): 0 / 50
Loss of Signal Seconds (LOSS): 0 / 0
Unavailable Seconds (UAS): 31 / 31
Header Error Code Errors (HEC): 0 / 0
Non Pre-emtive CRC errors (CRC_P): 0 / 0
Pre-emtive CRC errors (CRCP_P): 0 / 0
Line Uptime: 2m 3s
ATU-C System Vendor ID: Broadcom 176.15
Power Management Mode: L0 - Synchronized
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Enable setting a host-specific lease time for static hosts.
Format is similar as for the default lease time: e.g. 2m, 12h, 3d, infinite
Default lease time is used for all hosts without host-specific definition.
Support for the option was added to Openwrt trunk by r48801:
https://dev.openwrt.org/changeset/48801
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Map DUIDs to their corresponding MAC addresses in order to correlate them with
IPv4 information. This is useful to e.g. identify IPv6 hosts which do not send
a name.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
* add more WPA-EAP phase2 authentication methods.
* client cert, client key and key password are only relevant for
WPA EAP-TLS, change dependency accordingly.
* add support for certificates and key for EAP-TLS phase2 auth.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Copy the changes made by f8d0ba00b2
also to the interface details pages in order to clarify display of
multiple addresses.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Some applications only support ipv4 so add ipv4only option
to host and hostport datatypes so that for thos applications
that when an IP address is specified only and ipv4 ip address
gets accepted.
For better view of 'Interface Overview' IPv4/IPv6 addresses for
interfaces should be displayed as lists, but not as comma separated
strings.
Signed-off-by: Alexander Logger <intagger@gmail.com>
Previously the global configuration options were missing the the LuCI configuration,
however these options are useful, so make them available to the UI.
