- Turn IPv4-Address into IPv4 address
- Turn IPv4-Gateway into IPv4 gateway
- Turn IPv6-Address into IPv6 address
- Turn IPv6-Gateway into IPv6 gateway
- Turn MAC-Address into MAC address
Also remove related duplicate translation entries.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The iptables mark field is 32 bits wide, which is 4 bytes and so 8 hex
characters. Fix the fwmark validation to allow 8 characters in the hex
string.
Fixes: #5098
Suggested-by: Robert <32970961+differentblue@users.noreply.github.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This is required to resolve clashes with the generic "option device"
referring to netdev names in current netifd versions.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Those are L2 options that are not part of interfaces (L3), should not be
set there and don't work. Setting MAC and MTU should be done at device
layer (config device) and is supported for basic types already.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The introduction of network device configuration support also implemented
all common, protocol-independent interface options directly in the
interface config view, so drop the redundant option definitions.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Prepares for 5.10 migration. wireguard-tools will bring in the correct
wireguard kernel module dependency - either kmod-wireguard or
kmod-wireguard-oot.
Depends on https://github.com/openwrt/openwrt/pull/3885
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Better handling of Type of Service (IPv4), Traffic Class (IPv6) values
Optional value Local endpoint address is detected and pre-filled in the interface
Signed-off-by: Jan Bětík <jan.betik@svine.su>
legacymap causes map to use the legacy IPv6 Interface Identifier format
that was described in draft-ietf-softwire-map-00, but was eventually
changed in RFC7597. It is however still used by some major ISPs,
including in Japan.
Signed-off-by: Remi NGUYEN VAN <remi.nguyenvan+openwrt@gmail.com>
"type" is already used as a common option for all protocols. This makes
the configuration ambiguous, and Luci sees JS errors when trying to save
a MAP configuration.
Switch to "maptype" instead to avoid the conflict. MAP currently uses
"maptype" and falls back to "type" when not specified.
Signed-off-by: Remi NGUYEN VAN <remi.nguyenvan+openwrt@gmail.com>
I'm running several GRE tunnels to different locations and
the option to see and to configure GRE tunnels in LuCI was not
crucial but nice to have.
Signed-off-by: Jan Bětík <jan.betik@svine.su>
This addresses the issue of openconnect.sh from openconnect package expecting
a vpn- suffix for the files, while the frontend didn't.
Signed-off-by: Friendly fellow <DasTestament@users.noreply.github.com>
[reword commit message]
Ref: https://github.com/openwrt/packages/issues/11584
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This change allows to configure `nohostroute` option for wireguard to explicitely prevent creation
of host routes to endpoints.
By default without `option nohostroute '1'`, an explicite route to the peer's endpoint will be created in the main routing table with the next hop to the gateway. However, it causes issues with some setup. Enabling this option will inhibit this behavior. See discussions at http://lists.openwrt.org/pipermail/openwrt-devel/2019-March/016329.html.
Signed-off-by: Yuxiang Zhu <vfreex@gmail.com>
