f61e754522
This is sold as a dual-band 802.11ac range extender. It has a sliding switch for Extender mode or Access Point mode, a WPS button, a recessed Reset button, a hard-power button, and a multitude of LED's, some multiplexed via an NXP 74AHC164D chip. The internal serial header pinout is Vcc, Tx, Rx, GND, with GND closest to the corner of the board. You may connect at 115200 bps, 8 data bits, no parity, 1 stop bit. Specification: - System-On-Chip: QCA9558 - CPU/Speed: 720 MHz - Flash-Chip: Winbond 25Q128FVSG - Flash size: 16 MiB - RAM: 128 MiB - Wireless No1: QCA9558 on-chip 2.4GHz 802.11bgn, 3x3 - Wireless No2: QCA99x0 chip 5GHz 802.11an+ac, 4x4 - PHY: Atheros AR8035-A Installation: If you can get to the stock firmware's firmware upgrade option, just feed it the factory.img and boot as usual. As an alternative, TFTP the factory.img to the bootloader. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [whitespace fix in DTS and reorder of make variables] Signed-off-by: Petr Štetiar <ynezz@true.cz>
370 lines
9 KiB
Bash
Executable file
370 lines
9 KiB
Bash
Executable file
#!/bin/sh
|
|
|
|
. /lib/functions/system.sh
|
|
. /lib/functions/uci-defaults.sh
|
|
. /lib/functions/k2t.sh
|
|
|
|
ath79_setup_interfaces()
|
|
{
|
|
local board="$1"
|
|
|
|
case "$board" in
|
|
avm,fritz300e|\
|
|
devolo,dvl1200i|\
|
|
devolo,dvl1750c|\
|
|
devolo,dvl1750i|\
|
|
glinet,ar300m-lite|\
|
|
netgear,ex6400|\
|
|
netgear,ex7300|\
|
|
ocedo,koala|\
|
|
ocedo,raccoon|\
|
|
pcs,cap324|\
|
|
pisen,wmm003n|\
|
|
pqi,air-pen|\
|
|
tplink,cpe210-v2|\
|
|
tplink,cpe210-v3|\
|
|
tplink,re350k-v1|\
|
|
tplink,re450-v2|\
|
|
tplink,tl-mr10u|\
|
|
tplink,tl-mr3020-v1|\
|
|
tplink,tl-mr3040-v2|\
|
|
tplink,tl-wa901nd-v2|\
|
|
tplink,tl-wr703n|\
|
|
ubnt,bullet-m|\
|
|
ubnt,bullet-m-xw|\
|
|
ubnt,lap-120|\
|
|
ubnt,nanobeam-ac|\
|
|
ubnt,nanostation-ac-loco|\
|
|
ubnt,rocket-m|\
|
|
ubnt,unifiac-lite|\
|
|
ubnt,unifiac-mesh|\
|
|
ubnt,unifi|\
|
|
wd,mynet-wifi-rangeextender|\
|
|
winchannel,wb2000)
|
|
ucidef_set_interface_lan "eth0"
|
|
;;
|
|
avm,fritz4020|\
|
|
pcs,cr3000|\
|
|
tplink,archer-c58-v1|\
|
|
tplink,archer-c59-v1)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan:1" "2:lan:4" "3:lan:3" "4:lan:2"
|
|
;;
|
|
buffalo,bhr-4grv|\
|
|
buffalo,wzr-hp-g450h)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "2:lan" "3:lan" "4:lan" "5:lan" "1:wan"
|
|
;;
|
|
buffalo,bhr-4grv2)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "6@eth0"
|
|
;;
|
|
buffalo,wzr-hp-ag300h)
|
|
ucidef_set_interface_wan "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
|
|
;;
|
|
buffalo,wzr-hp-g302h-a1a0)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "1:lan:1" "3:lan:4" "4:lan:3" "5:lan:2" "2:wan"
|
|
;;
|
|
comfast,cf-e5|\
|
|
glinet,gl-ar150|\
|
|
glinet,gl-ar300m-nand|\
|
|
glinet,gl-ar300m-nor|\
|
|
glinet,gl-x750|\
|
|
tplink,tl-wr810n-v1|\
|
|
tplink,tl-wr810n-v2|\
|
|
ubnt,routerstation|\
|
|
yuncore,a770)
|
|
ucidef_set_interfaces_lan_wan "eth1" "eth0"
|
|
;;
|
|
devolo,dvl1200e|\
|
|
devolo,dvl1750e|\
|
|
ocedo,ursus)
|
|
ucidef_set_interface_lan "eth0 eth1"
|
|
;;
|
|
dlink,dir-825-b1)
|
|
ucidef_set_interface_wan "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "5@eth0"
|
|
;;
|
|
dlink,dir-825-c1|\
|
|
dlink,dir-835-a1|\
|
|
dlink,dir-859-a1|\
|
|
engenius,epg5000|\
|
|
tplink,archer-c2-v3|\
|
|
tplink,tl-wr1043nd-v4)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
|
|
;;
|
|
elecom,wrc-1750ghbk2-i|\
|
|
elecom,wrc-300ghbk2-i)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "2:lan:4" "3:lan:3" "4:lan:2" "5:lan:1" "1:wan"
|
|
;;
|
|
embeddedwireless,dorin)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "1:wan" "2:lan:3" "3:lan:2"
|
|
;;
|
|
engenius,ews511ap)
|
|
ucidef_set_interface_lan "eth0 eth1" "dhcp"
|
|
;;
|
|
etactica,eg200)
|
|
ucidef_set_interface_lan "eth0" "dhcp"
|
|
;;
|
|
glinet,gl-ar750s)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "2:lan:2" "3:lan:1" "1:wan"
|
|
;;
|
|
iodata,etg3-r|\
|
|
iodata,wn-ac1167dgr|\
|
|
iodata,wn-ac1600dgr|\
|
|
iodata,wn-ac1600dgr2|\
|
|
iodata,wn-ag300dgr|\
|
|
pcs,cr5000)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan"
|
|
;;
|
|
librerouter,librerouter-v1)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "5:wan" "6@eth1" "4:lan"
|
|
;;
|
|
nec,wg1200cr|\
|
|
ubnt,nanostation-ac|\
|
|
ubnt,unifiac-mesh-pro|\
|
|
ubnt,unifiac-pro)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "2:lan" "3:wan"
|
|
;;
|
|
nec,wg800hp)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "2:lan" "3:lan" "4:lan" "1:wan"
|
|
;;
|
|
netgear,wndr3700|\
|
|
netgear,wndr3700v2|\
|
|
netgear,wndr3800)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "5u@eth0"
|
|
ucidef_add_switch_attr "switch0" "blinkrate" 2
|
|
ucidef_add_switch_port_attr "switch0" 1 led 6
|
|
ucidef_add_switch_port_attr "switch0" 2 led 9
|
|
ucidef_add_switch_port_attr "switch0" 5 led 2
|
|
;;
|
|
netgear,wnr612-v2|\
|
|
on,n150r|\
|
|
tplink,tl-wr841-v7)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan" "2:lan" "3:lan" "4:lan"
|
|
;;
|
|
phicomm,k2t)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "3:lan:1" "5:lan:2" "4:wan"
|
|
;;
|
|
rosinson,wr818)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "1:lan" "2:lan" "3:wan"
|
|
;;
|
|
tplink,archer-c5-v1|\
|
|
tplink,archer-c7-v1|\
|
|
tplink,archer-c7-v2|\
|
|
tplink,tl-wdr4900-v2)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "2:lan" "3:lan" "4:lan" "5:lan" "6@eth0" "1:wan"
|
|
;;
|
|
buffalo,whr-g301n|\
|
|
tplink,tl-mr3220-v1|\
|
|
tplink,tl-mr3420-v1|\
|
|
tplink,tl-wr841-v9|\
|
|
tplink,tl-wr841-v11|\
|
|
ubnt,airrouter)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
|
|
;;
|
|
tplink,archer-a7-v5|\
|
|
tplink,archer-c6-v2|\
|
|
tplink,archer-c7-v4|\
|
|
tplink,archer-c7-v5|\
|
|
tplink,tl-wdr3600|\
|
|
tplink,tl-wdr4300|\
|
|
tplink,tl-wr941n-v7-cn)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "2:lan:1" "3:lan:2" "4:lan:3" "5:lan:4" "1:wan"
|
|
;;
|
|
tplink,tl-wr1043nd-v1)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "5@eth0"
|
|
;;
|
|
tplink,tl-wr1043nd-v2|\
|
|
tplink,tl-wr1043nd-v3)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan" "6@eth0"
|
|
;;
|
|
tplink,tl-wr2543-v1)
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "9@eth0"
|
|
;;
|
|
tplink,tl-wr740n-v1|\
|
|
tplink,tl-wr740n-v3|\
|
|
tplink,tl-wr741-v1|\
|
|
tplink,tl-wr743nd-v1|\
|
|
tplink,tl-wr841-v5|\
|
|
tplink,tl-wr941-v4)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan" "2:lan" "3:lan" "4:lan"
|
|
;;
|
|
tplink,tl-wr710n-v1)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "3:lan"
|
|
;;
|
|
tplink,tl-wr740n-v4|\
|
|
tplink,tl-wr741nd-v4|\
|
|
tplink,tl-wr841-v8|\
|
|
tplink,tl-wr842n-v1|\
|
|
tplink,tl-wr842n-v2)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "1:lan:4" "2:lan:1" "3:lan:2" "4:lan:3"
|
|
;;
|
|
tplink,tl-wr941-v2)
|
|
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
|
|
;;
|
|
ubnt,acb-isp)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "2:lan:1" "3:lan:3" "4:lan:2"
|
|
;;
|
|
ubnt,routerstation-pro)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "2:lan:3" "3:lan:2" "4:lan:1"
|
|
;;
|
|
ubnt,nanostation-m-xw)
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth0" "5:lan" "1:wan"
|
|
;;
|
|
xiaomi,mi-router-4q)
|
|
ucidef_set_interface_wan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0@eth1" "3:lan:1" "4:lan:2"
|
|
;;
|
|
*)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
;;
|
|
esac
|
|
}
|
|
|
|
ath79_setup_macs()
|
|
{
|
|
local board="$1"
|
|
|
|
case "$board" in
|
|
avm,fritz300e)
|
|
lan_mac=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)"))
|
|
;;
|
|
avm,fritz4020)
|
|
lan_mac=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)"))
|
|
wan_mac=$(fritz_tffs -n macb -i $(find_mtd_part "tffs (1)"))
|
|
;;
|
|
dlink,dir-825-b1)
|
|
lan_mac=$(mtd_get_mac_text "caldata" 65440)
|
|
wan_mac=$(mtd_get_mac_text "caldata" 65460)
|
|
;;
|
|
dlink,dir-825-c1|\
|
|
dlink,dir-835-a1)
|
|
lan_mac=$(mtd_get_mac_text "mac" 4)
|
|
wan_mac=$(mtd_get_mac_text "mac" 24)
|
|
;;
|
|
dlink,dir-859-a1|\
|
|
nec,wg1200cr)
|
|
lan_mac=$(mtd_get_mac_ascii devdata "lanmac")
|
|
wan_mac=$(mtd_get_mac_ascii devdata "wanmac")
|
|
;;
|
|
elecom,wrc-1750ghbk2-i|\
|
|
elecom,wrc-300ghbk2-i)
|
|
wan_mac=$(macaddr_add "$(mtd_get_mac_binary ART 4098)" -2)
|
|
;;
|
|
engenius,epg5000|\
|
|
iodata,wn-ac1167dgr|\
|
|
iodata,wn-ac1600dgr|\
|
|
iodata,wn-ac1600dgr2|\
|
|
iodata,wn-ag300dgr)
|
|
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
|
|
wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr)
|
|
;;
|
|
engenius,ews511ap)
|
|
lan_mac=$(mtd_get_mac_text "u-boot-env" 233)
|
|
eth1_mac=$(macaddr_add "$lan_mac" 1)
|
|
ucidef_set_interface "eth0" ifname "eth0" protocol "none" macaddr "$lan_mac"
|
|
ucidef_set_interface "eth1" ifname "eth1" protocol "none" macaddr "$eth1_mac"
|
|
;;
|
|
iodata,etg3-r)
|
|
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
|
|
wan_mac=$(macaddr_add "$lan_mac" -1)
|
|
;;
|
|
jjplus,ja76pf2)
|
|
wan_mac=$(fconfig -s -r -d $(find_mtd_part "RedBoot config") -n alias/ethaddr)
|
|
lan_mac=$(macaddr_add "$wan_mac" 1)
|
|
;;
|
|
nec,wg800hp)
|
|
lan_mac=$(mtd_get_mac_text board_data 640)
|
|
wan_mac=$(mtd_get_mac_text board_data 1152)
|
|
;;
|
|
netgear,wndr3700|\
|
|
netgear,wndr3700v2|\
|
|
netgear,wndr3800)
|
|
lan_mac=$(macaddr_setbit_la "$(mtd_get_mac_binary art 0)")
|
|
;;
|
|
phicomm,k2t)
|
|
lan_mac=$(k2t_get_mac "lan_mac")
|
|
wan_mac=$(k2t_get_mac "wan_mac")
|
|
;;
|
|
rosinson,wr818)
|
|
wan_mac=$(mtd_get_mac_binary factory 0)
|
|
lan_mac=$(macaddr_setbit_la "$wan_mac")
|
|
;;
|
|
tplink,archer-a7-v5|\
|
|
tplink,archer-c7-v5)
|
|
base_mac=$(mtd_get_mac_binary info 8)
|
|
wan_mac=$(macaddr_add "$base_mac" 1)
|
|
;;
|
|
tplink,archer-c7-v4)
|
|
base_mac=$(mtd_get_mac_binary config 8)
|
|
wan_mac=$(macaddr_add "$base_mac" 1)
|
|
;;
|
|
tplink,tl-wr1043nd-v4)
|
|
base_mac=$(mtd_get_mac_binary product-info 8)
|
|
wan_mac=$(macaddr_add "$base_mac" 1)
|
|
;;
|
|
tplink,tl-wr941-v2|\
|
|
tplink,tl-wr941n-v7-cn)
|
|
base_mac=$(mtd_get_mac_binary u-boot 130048)
|
|
wan_mac=$(macaddr_add "$base_mac" 1)
|
|
;;
|
|
ubnt,routerstation|\
|
|
ubnt,routerstation-pro)
|
|
wan_mac=$(fconfig -s -r -d $(find_mtd_part "RedBoot config") -n ar7100_esa)
|
|
lan_mac=$(macaddr_add "$wan_mac" 1)
|
|
;;
|
|
wd,mynet-wifi-rangeextender)
|
|
lan_mac=$(nvram get et0macaddr)
|
|
;;
|
|
esac
|
|
|
|
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
|
|
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
|
|
}
|
|
|
|
board_config_update
|
|
board=$(board_name)
|
|
ath79_setup_interfaces $board
|
|
ath79_setup_macs $board
|
|
board_config_flush
|
|
|
|
exit 0
|