eb3a5ddba0
Device specifications:
======================
* Qualcomm/Atheros AR9330 rev 1
* 400/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ builtin switch port 1
+ used as LAN interface
- eth1
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to
the device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
75 lines
1.7 KiB
Bash
75 lines
1.7 KiB
Bash
#
|
|
# Copyright (C) 2011 OpenWrt.org
|
|
#
|
|
|
|
PART_NAME=firmware
|
|
REQUIRE_IMAGE_METADATA=1
|
|
|
|
RAMFS_COPY_BIN='fw_printenv fw_setenv'
|
|
RAMFS_COPY_DATA='/etc/fw_env.config /var/lock/fw_printenv.lock'
|
|
|
|
redboot_fis_do_upgrade() {
|
|
local append
|
|
local sysup_file="$1"
|
|
local kern_part="$2"
|
|
local magic=$(get_magic_word "$sysup_file")
|
|
|
|
if [ "$magic" = "4349" ]; then
|
|
local kern_length=0x$(dd if="$sysup_file" bs=2 skip=1 count=4 2>/dev/null)
|
|
|
|
[ -f "$UPGRADE_BACKUP" ] && append="-j $UPGRADE_BACKUP"
|
|
dd if="$sysup_file" bs=64k skip=1 2>/dev/null | \
|
|
mtd -r $append -F$kern_part:$kern_length:0x80060000,rootfs write - $kern_part:rootfs
|
|
|
|
elif [ "$magic" = "7379" ]; then
|
|
local board_dir=$(tar tf $sysup_file | grep -m 1 '^sysupgrade-.*/$')
|
|
local kern_length=$(tar xf $sysup_file ${board_dir}kernel -O | wc -c)
|
|
|
|
[ -f "$UPGRADE_BACKUP" ] && append="-j $UPGRADE_BACKUP"
|
|
tar xf $sysup_file ${board_dir}kernel ${board_dir}root -O | \
|
|
mtd -r $append -F$kern_part:$kern_length:0x80060000,rootfs write - $kern_part:rootfs
|
|
|
|
else
|
|
echo "Unknown image, aborting!"
|
|
return 1
|
|
fi
|
|
}
|
|
|
|
platform_check_image() {
|
|
return 0
|
|
}
|
|
|
|
platform_do_upgrade() {
|
|
local board=$(board_name)
|
|
|
|
case "$board" in
|
|
adtran,bsap1800-v2|\
|
|
adtran,bsap1840)
|
|
redboot_fis_do_upgrade "$1" vmlinux_2
|
|
;;
|
|
jjplus,ja76pf2)
|
|
redboot_fis_do_upgrade "$1" linux
|
|
;;
|
|
openmesh,om2p-v4|\
|
|
openmesh,om2p-hs-v1|\
|
|
openmesh,om2p-hs-v2|\
|
|
openmesh,om2p-hs-v3|\
|
|
openmesh,om2p-hs-v4|\
|
|
openmesh,om2p-lc)
|
|
PART_NAME="inactive"
|
|
platform_do_upgrade_openmesh "$1"
|
|
;;
|
|
plasmacloud,pa300|\
|
|
plasmacloud,pa300e)
|
|
PART_NAME="inactive"
|
|
platform_do_upgrade_dualboot_datachk "$1"
|
|
;;
|
|
ubnt,routerstation|\
|
|
ubnt,routerstation-pro)
|
|
redboot_fis_do_upgrade "$1" kernel
|
|
;;
|
|
*)
|
|
default_do_upgrade "$1"
|
|
;;
|
|
esac
|
|
}
|