cd09f26660
Hardware: * SoC: Qualcomm Atheros QCA9558 * RAM: 256MB * Flash: 16MB SPI NOR * Ethernet: 2x 10/100/1000 (1x 802.3at PoE-PD) * WiFi 2.4GHz: Qualcomm Atheros QCA9558 * WiFi 5GHz: Qualcomm Ahteros QCA9880-2R4E * LEDS: 1x 5GHz, 1x 2.4GHz, 1x LAN1(POE), 1x LAN2, 1x POWER * Buttons: 1x RESET * UART: 1x RJ45 RS-232 Console port Installation via stock firmware: * Install the factory image via the stock firmware web interface Installation via bootloader Emergency Web Server: * Connect your PC to the LAN1(PoE) port * Configure your PC with IP address 192.168.0.90 * Open a serial console to the Console port (115200,8n1) * Press "q" within 2s when "press 'q' to stop autoboot" appears * Open http://192.168.0.50 in a browser * Upload either the factory or the sysupgrade image * Once you see "write image into flash...OK,dest addr=0x9f070000" you can power-cycle the device. Ignore "checksum bad" messages. Setting the MAC addresses for the ethernet interfaces via /etc/board.d/02_network adds the following snippets to /etc/config/network: config device 'lan_eth0_1_dev' option name 'eth0.1' option macaddr 'xx:xx:xx:xx:xx:xx' config device 'wan_eth1_2_dev' option name 'eth1.2' option macaddr 'xx:xx:xx:xx:xx:xx' This would result in the proper MAC addresses being set for the VLAN subinterfaces, but the parent interfaces would still have a random MAC address. Using untagged VLANs could solve this, but would still leave those extra snippets in /etc/config/network, and then the device VLAN setup would differ from the one used in ar71xx. Therefore, the MAC addresses of the ethernet interfaces are being set via preinit instead. The bdcfg partition contains 4 MAC address labels: - lanmac - wanmac - wlanmac - wlanmac_a The first 3 all contain the same MAC address, which is also the one on the label. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
206 lines
5.6 KiB
Bash
206 lines
5.6 KiB
Bash
#!/bin/sh
|
|
|
|
[ -e /lib/firmware/$FIRMWARE ] && exit 0
|
|
|
|
. /lib/functions/caldata.sh
|
|
. /lib/functions/k2t.sh
|
|
|
|
board=$(board_name)
|
|
|
|
case "$FIRMWARE" in
|
|
"ath10k/cal-pci-0000:00:00.0.bin")
|
|
case $board in
|
|
avm,fritz1750e)
|
|
caldata_extract "urlader" 0x198a 0x844
|
|
;;
|
|
comfast,cf-wr650ac-v1|\
|
|
comfast,cf-wr650ac-v2|\
|
|
devolo,magic-2-wifi|\
|
|
ubnt,unifiac-lite|\
|
|
ubnt,unifiac-lr|\
|
|
ubnt,unifiac-mesh|\
|
|
ubnt,unifiac-mesh-pro|\
|
|
ubnt,lap-120|\
|
|
ubnt,litebeam-ac-gen2|\
|
|
ubnt,nanobeam-ac|\
|
|
ubnt,nanostation-ac|\
|
|
ubnt,nanostation-ac-loco|\
|
|
ubnt,powerbeam-5ac-500|\
|
|
ubnt,powerbeam-5ac-gen2|\
|
|
ubnt,unifiac-pro|\
|
|
yuncore,a770)
|
|
caldata_extract "art" 0x5000 0x844
|
|
;;
|
|
devolo,dvl1200e|\
|
|
devolo,dvl1200i|\
|
|
devolo,dvl1750c|\
|
|
devolo,dvl1750e|\
|
|
devolo,dvl1750i|\
|
|
devolo,dvl1750x)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) -1)
|
|
;;
|
|
dlink,dap-2695-a1)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(mtd_get_mac_ascii bdcfg wlanmac_a)
|
|
;;
|
|
dlink,dir-859-a1)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(mtd_get_mac_ascii devdata "wlan5mac")
|
|
;;
|
|
elecom,wrc-1750ghbk2-i)
|
|
caldata_extract "art" 0x5000 0x844
|
|
;;
|
|
engenius,ecb1750)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(mtd_get_mac_ascii u-boot-env athaddr)
|
|
;;
|
|
engenius,epg5000|\
|
|
iodata,wn-ac1167dgr|\
|
|
iodata,wn-ac1600dgr2|\
|
|
sitecom,wlr-7100)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +1)
|
|
;;
|
|
engenius,ews511ap)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
|
|
;;
|
|
glinet,gl-ar750)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) +1)
|
|
;;
|
|
glinet,gl-x750)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) +2)
|
|
;;
|
|
nec,wg800hp)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(mtd_get_mac_text board_data 0x880)
|
|
;;
|
|
ocedo,koala|\
|
|
ocedo,ursus)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(mtd_get_mac_binary art 0xc)
|
|
;;
|
|
openmesh,om5p-ac-v2)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
|
|
;;
|
|
qihoo,c301)
|
|
caldata_extract "radiocfg" 0x5000 0x844
|
|
ath10k_patch_mac $(mtd_get_mac_ascii devdata wlan5mac)
|
|
;;
|
|
tplink,archer-a7-v5|\
|
|
tplink,archer-c2-v3|\
|
|
tplink,archer-c7-v4|\
|
|
tplink,archer-c7-v5|\
|
|
tplink,archer-c25-v1)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary info 0x8) -1)
|
|
;;
|
|
tplink,archer-c5-v1|\
|
|
tplink,archer-c7-v2)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary u-boot 0x1fc00) -1)
|
|
;;
|
|
tplink,archer-d50-v1)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary romfile 0xf100) +2)
|
|
;;
|
|
tplink,archer-d7-v1|\
|
|
tplink,archer-d7b-v1)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary romfs 0xf100) +2)
|
|
;;
|
|
tplink,re350k-v1)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary config 0x10008) +2)
|
|
;;
|
|
tplink,re355-v1|\
|
|
tplink,re450-v1)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -2)
|
|
;;
|
|
tplink,re450-v2|\
|
|
tplink,re450-v3)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary info 0x8) +1)
|
|
;;
|
|
tplink,tl-wr902ac-v1)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary tplink 0x8) -1)
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/cal-pci-0000:01:00.0.bin")
|
|
case $board in
|
|
sitecom,wlr-8100)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +1)
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/pre-cal-pci-0000:00:00.0.bin")
|
|
case $board in
|
|
comfast,cf-e313ac)
|
|
caldata_extract "art" 0x5000 0x2f20
|
|
ath10k_patch_mac $(mtd_get_mac_binary art 0x6)
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
rm /lib/firmware/ath10k/QCA9888/hw2.0/board-2.bin
|
|
;;
|
|
comfast,cf-e560ac|\
|
|
comfast,cf-ew72|\
|
|
comfast,cf-wr752ac-v1)
|
|
caldata_extract "art" 0x5000 0x2f20
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) +2)
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
rm /lib/firmware/ath10k/QCA9888/hw2.0/board-2.bin
|
|
;;
|
|
dlink,dir-842-c1|\
|
|
dlink,dir-842-c2|\
|
|
dlink,dir-842-c3|\
|
|
nec,wg1200cr)
|
|
caldata_extract "art" 0x5000 0x2f20
|
|
ath10k_patch_mac $(mtd_get_mac_ascii devdata wlan5mac)
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
;;
|
|
netgear,ex6400|\
|
|
netgear,ex7300)
|
|
caldata_extract "caldata" 0x5000 0x2f20
|
|
ath10k_patch_mac $(mtd_get_mac_binary caldata 0xc)
|
|
;;
|
|
phicomm,k2t)
|
|
caldata_extract "art" 0x5000 0x2f20
|
|
ath10k_patch_mac $(k2t_get_mac "5g_mac")
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
;;
|
|
tplink,archer-c58-v1|\
|
|
tplink,archer-c59-v1|\
|
|
tplink,archer-c59-v2|\
|
|
tplink,archer-c60-v1|\
|
|
tplink,archer-c60-v2|\
|
|
tplink,archer-c60-v3|\
|
|
tplink,archer-c6-v2|\
|
|
tplink,archer-c6-v2-us)
|
|
caldata_extract "art" 0x5000 0x2f20
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary mac 0x8) -1)
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
;;
|
|
yuncore,a782|\
|
|
yuncore,xd4200)
|
|
caldata_extract "art" 0x5000 0x2f20
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
;;
|
|
esac
|
|
;;
|
|
*)
|
|
exit 1
|
|
;;
|
|
esac
|