157e17e985
Hardware: * SoC: Atheros AR9342-BL1A * RAM: 64MB DDR2 (Winbond W9751G6KB-25) * Flash: 16MB SPI NOR (Macronix MX25L12835FZ2I-10G) * Ethernet: 1x 10/100/1000 Mbps (Atheros AR8035-A) with 24V PoE support * Wifi 2.4GHz: Atheros AR9340 v2 * WiFi 5GHz: Ubiquiti U-AME-G1-BR4A (rebranded QCA988X v2) * LEDs: 1x Power, 1x Ethernet * Buttons: 1x Reset * UART: 1x TTL 115200n8, 3.3V RX TX GND, 3.3V pin closest to RJ45 port The LEDs do not seem to be connected to any GPIO, so there is currently no way to control them. Installation via U-Boot, TFTP and serial console: * Configure your TFTP server with IP 192.168.1.254 * Connect serial console and power up the device * Hit any key to stop autoboot * tftpboot 0x81000000 openwrt-ath79-generic-ubnt_litebeam-ac-gen2-initramfs-kernel.bin * bootm 0x81000000 * copy openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin to /tmp * sysupgrade /tmp/openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Acked-by: Petr Štetiar <ynezz@true.cz> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
168 lines
4.5 KiB
Bash
168 lines
4.5 KiB
Bash
#!/bin/sh
|
|
|
|
[ -e /lib/firmware/$FIRMWARE ] && exit 0
|
|
|
|
. /lib/functions/caldata.sh
|
|
. /lib/functions/k2t.sh
|
|
|
|
board=$(board_name)
|
|
|
|
case "$FIRMWARE" in
|
|
"ath10k/cal-pci-0000:00:00.0.bin")
|
|
case $board in
|
|
comfast,cf-wr650ac-v1|\
|
|
comfast,cf-wr650ac-v2|\
|
|
ubnt,unifiac-lite|\
|
|
ubnt,unifiac-lr|\
|
|
ubnt,unifiac-mesh|\
|
|
ubnt,unifiac-mesh-pro|\
|
|
ubnt,lap-120|\
|
|
ubnt,litebeam-ac-gen2|\
|
|
ubnt,nanobeam-ac|\
|
|
ubnt,nanostation-ac|\
|
|
ubnt,nanostation-ac-loco|\
|
|
ubnt,unifiac-pro|\
|
|
yuncore,a770)
|
|
caldata_extract "art" 0x5000 0x844
|
|
;;
|
|
devolo,dvl1200e|\
|
|
devolo,dvl1200i|\
|
|
devolo,dvl1750c|\
|
|
devolo,dvl1750e|\
|
|
devolo,dvl1750i|\
|
|
devolo,dvl1750x)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) -1)
|
|
;;
|
|
dlink,dir-859-a1)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(mtd_get_mac_ascii devdata "wlan5mac")
|
|
;;
|
|
elecom,wrc-1750ghbk2-i)
|
|
caldata_extract "art" 0x5000 0x844
|
|
;;
|
|
engenius,ecb1750)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(mtd_get_mac_ascii u-boot-env athaddr)
|
|
;;
|
|
engenius,epg5000|\
|
|
iodata,wn-ac1167dgr|\
|
|
iodata,wn-ac1600dgr2|\
|
|
sitecom,wlr-7100)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +1)
|
|
;;
|
|
engenius,ews511ap)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
|
|
;;
|
|
glinet,gl-ar750)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) +1)
|
|
;;
|
|
glinet,gl-x750)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) +2)
|
|
;;
|
|
nec,wg800hp)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(mtd_get_mac_text board_data 0x880)
|
|
;;
|
|
ocedo,koala|\
|
|
ocedo,ursus)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(mtd_get_mac_binary art 0xc)
|
|
;;
|
|
openmesh,om5p-ac-v2)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
|
|
;;
|
|
qihoo,c301)
|
|
caldata_extract "radiocfg" 0x5000 0x844
|
|
ath10k_patch_mac $(mtd_get_mac_ascii devdata wlan5mac)
|
|
;;
|
|
tplink,archer-a7-v5|\
|
|
tplink,archer-c2-v3|\
|
|
tplink,archer-c7-v4|\
|
|
tplink,archer-c7-v5|\
|
|
tplink,archer-c25-v1)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary info 0x8) -1)
|
|
;;
|
|
tplink,archer-c5-v1|\
|
|
tplink,archer-c7-v2)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary u-boot 0x1fc00) -1)
|
|
;;
|
|
tplink,archer-d50-v1)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary romfile 0xf100) +2)
|
|
;;
|
|
tplink,re350k-v1)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary config 0x10008) +2)
|
|
;;
|
|
tplink,re355-v1|\
|
|
tplink,re450-v1)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -2)
|
|
;;
|
|
tplink,re450-v2)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary info 0x8) +1)
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/pre-cal-pci-0000:00:00.0.bin")
|
|
case $board in
|
|
comfast,cf-e313ac)
|
|
caldata_extract "art" 0x5000 0x2f20
|
|
ath10k_patch_mac $(mtd_get_mac_binary art 0x6)
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
rm /lib/firmware/ath10k/QCA9888/hw2.0/board-2.bin
|
|
;;
|
|
dlink,dir-842-c1|\
|
|
dlink,dir-842-c2|\
|
|
dlink,dir-842-c3|\
|
|
nec,wg1200cr)
|
|
caldata_extract "art" 0x5000 0x2f20
|
|
ath10k_patch_mac $(mtd_get_mac_ascii devdata wlan5mac)
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
;;
|
|
netgear,ex6400|\
|
|
netgear,ex7300)
|
|
caldata_extract "caldata" 0x5000 0x2f20
|
|
ath10k_patch_mac $(mtd_get_mac_binary caldata 0xc)
|
|
;;
|
|
phicomm,k2t)
|
|
caldata_extract "art" 0x5000 0x2f20
|
|
ath10k_patch_mac $(k2t_get_mac "5g_mac")
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
;;
|
|
tplink,archer-c58-v1|\
|
|
tplink,archer-c59-v1|\
|
|
tplink,archer-c59-v2|\
|
|
tplink,archer-c60-v1|\
|
|
tplink,archer-c60-v2|\
|
|
tplink,archer-c6-v2|\
|
|
tplink,archer-c6-v2-us)
|
|
caldata_extract "art" 0x5000 0x2f20
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary mac 0x8) -1)
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
;;
|
|
yuncore,a782|\
|
|
yuncore,xd4200)
|
|
caldata_extract "art" 0x5000 0x2f20
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
;;
|
|
esac
|
|
;;
|
|
*)
|
|
exit 1
|
|
;;
|
|
esac
|