Difuse/difos
2
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity Actions
difos/target/linux/ath79/base-files/etc/board.d/02_network
Daniel Gimpelevich bc18c2bfe7 ath79: add support for Bluesocket BSAP1880 board 
This board was used in dual-band 802.11n enterprise access points, models
BSAP-1800v2 and BSAP-1840, introduced in 2010 by Bluesocket, which was
acquired by Adtran in 2011, who has now EOL'ed them. They differed only in
that the BSAP-1840's antennae were detachable, while the BSAP-1800v2's were
inside the case. They have an external RJ-45 console port, which works with
standard Cisco 72-3383-01 console cables.

Specification:
- System-On-Chip: AR7161
- CPU/Speed: 600 MHz
- Flash-Chip: Macronix MX25L12845E
- Flash size: 16 MiB
- RAM: 64 MiB
- Wireless No1: Lite-On WN2601A card: AR9160/AR9103 2.4GHz 802.11bgn
- Wireless No2: Lite-On WN2502A card: AR9160/AR9106 5GHz 802.11an
- PHY: Vitesse VSC8601, Rev. B

Installation:
1. Connect to the serial console using a terminal that supports YMODEM at
   115200 bps, 8 data bits, no parity, 1 stop bit
2. Interrupt the bootloader using its password, which is: r00t
3. Issue the "fis init" command, confirming if prompted
4. Look at the length of the openwrt-ath79-generic-*-squashfs-kernel.bin
   file, and substitute it below, instead of where I have "LeNgTh"
5. Issue the following command, and upload this file using YMODEM protocol
   load -r -v -b 0x80060000 -m ymodem
6. Issue the following commands, substituting as mentioned above:
   fis create -b 0x80060000 -l LeNgTh vmlinux_2
   load -r -v -b 0x80100000 -m ymodem
7. Using YMODEM, upload openwrt-ath79-generic-*-squashfs-rootfs.bin
8. Issue the "fis free" command, and for the first range in its response,
   use a hexadecimal calculator to subtract the start from the end in order
   to substitute it below, with the leading "0x" to specify it in
   hexadecimal, instead of where I have "LeNgTh"
9. Issue the following commands, substituting as mentioned above:
   fis create -b 0x80100000 -l LeNgTh -e 0 -r 0 rootfs
   reset
10.Wait for the status LED to go solid green

Tested-by: Brian Gonyer <bgonyer@gmail.com>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[fixed obsolete $ARGV in platform_do_upgrade]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2019-07-17 22:59:29 +02:00

384 lines
9.4 KiB
Bash
Executable file
Raw Blame History

#!/bin/sh
. /lib/functions/system.sh
. /lib/functions/uci-defaults.sh
. /lib/functions/k2t.sh
ath79_setup_interfaces()
{
local board="$1"
case "$board" in
adtran,bsap1800-v2|\
adtran,bsap1840|\
aruba,ap-105|\
avm,fritz300e|\
devolo,dvl1200i|\
devolo,dvl1750c|\
devolo,dvl1750i|\
devolo,dvl1750x|\
engenius,ecb1750|\
glinet,ar300m-lite|\
netgear,ex6400|\
netgear,ex7300|\
ocedo,koala|\
ocedo,raccoon|\
pcs,cap324|\
pisen,wmm003n|\
pqi,air-pen|\
tplink,cpe210-v2|\
tplink,cpe210-v3|\
tplink,cpe610-v1|\
tplink,re350k-v1|\
tplink,re450-v2|\
tplink,tl-mr10u|\
tplink,tl-mr3020-v1|\
tplink,tl-mr3040-v2|\
tplink,tl-wa901nd-v2|\
tplink,tl-wr703n|\
ubnt,bullet-m|\
ubnt,bullet-m-xw|\
ubnt,lap-120|\
ubnt,nanobeam-ac|\
ubnt,nanostation-ac-loco|\
ubnt,rocket-m|\
ubnt,unifiac-lite|\
ubnt,unifiac-mesh|\
ubnt,unifi|\
wd,mynet-wifi-rangeextender|\
winchannel,wb2000)
ucidef_set_interface_lan "eth0"
;;
avm,fritz4020|\
pcs,cr3000|\
tplink,archer-c58-v1|\
tplink,archer-c59-v1)
ucidef_set_interface_wan "eth1"
ucidef_add_switch "switch0" \
"0@eth0" "1:lan:1" "2:lan:4" "3:lan:3" "4:lan:2"
;;
buffalo,bhr-4grv|\
buffalo,wzr-hp-g450h)
ucidef_add_switch "switch0" \
"0@eth0" "2:lan" "3:lan" "4:lan" "5:lan" "1:wan"
;;
buffalo,bhr-4grv2)
ucidef_add_switch "switch0" \
"0@eth1" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "6@eth0"
;;
buffalo,whr-g301n)
ucidef_set_interface_wan "eth0"
ucidef_add_switch "switch0" \
"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
;;
buffalo,wzr-hp-ag300h|\
tplink,archer-c25-v1|\
tplink,tl-mr3220-v1|\
tplink,tl-mr3420-v1|\
tplink,tl-wr841-v7|\
tplink,tl-wr841-v9|\
tplink,tl-wr841-v11|\
tplink,tl-wr842n-v1|\
tplink,tl-wr842n-v3|\
ubnt,airrouter)
ucidef_set_interface_wan "eth1"
ucidef_add_switch "switch0" \
"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
;;
buffalo,wzr-hp-g302h-a1a0)
ucidef_add_switch "switch0" \
"0@eth0" "1:lan:1" "3:lan:4" "4:lan:3" "5:lan:2" "2:wan"
;;
comfast,cf-e110n-v2|\
comfast,cf-e120a-v3|\
ubnt,nanostation-m|\
ubnt,routerstation)
ucidef_set_interfaces_lan_wan "eth1" "eth0"
;;
devolo,dvl1200e|\
devolo,dvl1750e|\
ocedo,ursus)
ucidef_set_interface_lan "eth0 eth1"
;;
dlink,dir-825-b1)
ucidef_set_interface_wan "eth1"
ucidef_add_switch "switch0" \
"0:lan" "1:lan" "2:lan" "3:lan" "5@eth0"
;;
dlink,dir-825-c1|\
dlink,dir-835-a1|\
dlink,dir-859-a1|\
engenius,epg5000|\
tplink,archer-c2-v3|\
tplink,tl-wr1043nd-v4|\
tplink,tl-wr1043n-v5)
ucidef_add_switch "switch0" \
"0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan"
;;
elecom,wrc-1750ghbk2-i|\
elecom,wrc-300ghbk2-i)
ucidef_add_switch "switch0" \
"0@eth0" "2:lan:4" "3:lan:3" "4:lan:2" "5:lan:1" "1:wan"
;;
embeddedwireless,dorin)
ucidef_add_switch "switch0" \
"0@eth0" "1:wan" "2:lan:3" "3:lan:2"
;;
engenius,ews511ap)
ucidef_set_interface_lan "eth0 eth1" "dhcp"
;;
etactica,eg200)
ucidef_set_interface_lan "eth0" "dhcp"
;;
glinet,gl-ar750s)
ucidef_add_switch "switch0" \
"0@eth0" "2:lan:2" "3:lan:1" "1:wan"
;;
iodata,etg3-r|\
iodata,wn-ac1167dgr|\
iodata,wn-ac1600dgr|\
iodata,wn-ac1600dgr2|\
iodata,wn-ag300dgr|\
pcs,cr5000|\
wd,mynet-n750)
ucidef_add_switch "switch0" \
"0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan"
;;
librerouter,librerouter-v1)
ucidef_add_switch "switch0" \
"0@eth0" "5:wan" "6@eth1" "4:lan"
;;
nec,wg1200cr|\
ubnt,nanostation-ac|\
ubnt,unifiac-mesh-pro|\
ubnt,unifiac-pro)
ucidef_add_switch "switch0" \
"0@eth0" "2:lan" "3:wan"
;;
nec,wg800hp)
ucidef_add_switch "switch0" \
"0@eth0" "2:lan" "3:lan" "4:lan" "1:wan"
;;
netgear,wndr3700|\
netgear,wndr3700v2|\
netgear,wndr3800)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "5u@eth0"
ucidef_add_switch_attr "switch0" "blinkrate" 2
ucidef_add_switch_port_attr "switch0" 1 led 6
ucidef_add_switch_port_attr "switch0" 2 led 9
ucidef_add_switch_port_attr "switch0" 5 led 2
;;
netgear,wnr612-v2|\
on,n150r|\
tplink,tl-wr740n-v1|\
tplink,tl-wr740n-v3|\
tplink,tl-wr741-v1|\
tplink,tl-wr743nd-v1|\
tplink,tl-wr841-v5|\
tplink,tl-wr941-v4)
ucidef_set_interface_wan "eth0"
ucidef_add_switch "switch0" \
"0@eth1" "1:lan" "2:lan" "3:lan" "4:lan"
;;
phicomm,k2t)
ucidef_add_switch "switch0" \
"0@eth0" "3:lan:1" "5:lan:2" "4:wan"
;;
qihoo,c301)
ucidef_set_interface_wan "eth1"
ucidef_add_switch "switch0" \
"0@eth0" "2:lan" "3:lan"
;;
rosinson,wr818)
ucidef_add_switch "switch0" \
"0@eth0" "1:lan" "2:lan" "3:wan"
;;
tplink,archer-a7-v5|\
tplink,archer-c6-v2|\
tplink,archer-c7-v4|\
tplink,archer-c7-v5|\
tplink,tl-wdr3600-v1|\
tplink,tl-wdr4300-v1|\
tplink,tl-wr941n-v7-cn)
ucidef_add_switch "switch0" \
"0@eth0" "2:lan:1" "3:lan:2" "4:lan:3" "5:lan:4" "1:wan"
;;
tplink,archer-c5-v1|\
tplink,archer-c7-v1|\
tplink,archer-c7-v2|\
tplink,tl-wdr4900-v2)
ucidef_add_switch "switch0" \
"0@eth1" "2:lan" "3:lan" "4:lan" "5:lan" "6@eth0" "1:wan"
;;
tplink,archer-d50-v1)
ucidef_add_switch "switch0" \
"0@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "1:wan"
;;
tplink,tl-wr1043nd-v1)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "5@eth0"
;;
tplink,tl-wr1043nd-v2|\
tplink,tl-wr1043nd-v3)
ucidef_add_switch "switch0" \
"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan" "6@eth0"
;;
tplink,tl-wr2543-v1)
ucidef_add_switch "switch0" \
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "9@eth0"
;;
tplink,tl-wr740n-v4|\
tplink,tl-wr741nd-v4|\
tplink,tl-wr841-v8|\
tplink,tl-wr842n-v2)
ucidef_set_interface_wan "eth1"
ucidef_add_switch "switch0" \
"0@eth0" "1:lan:4" "2:lan:1" "3:lan:2" "4:lan:3"
;;
tplink,tl-wr941-v2)
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" "wan"
;;
ubnt,acb-isp)
ucidef_set_interface_wan "eth1"
ucidef_add_switch "switch0" \
"0@eth0" "2:lan:1" "3:lan:3" "4:lan:2"
;;
ubnt,routerstation-pro)
ucidef_set_interface_wan "eth0"
ucidef_add_switch "switch0" \
"0@eth1" "2:lan:3" "3:lan:2" "4:lan:1"
;;
ubnt,nanostation-m-xw)
ucidef_add_switch "switch0" \
"0@eth0" "5:lan" "1:wan"
;;
zbtlink,zbt-wd323|\
xiaomi,mi-router-4q)
ucidef_set_interface_wan "eth1"
ucidef_add_switch "switch0" \
"0@eth0" "3:lan:1" "4:lan:2"
;;
*)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
;;
esac
}
ath79_setup_macs()
{
local board="$1"
case "$board" in
adtran,bsap1800-v2|\
adtran,bsap1840)
fconfig -s -w -d $(find_mtd_part "RedBoot config") -n boot_cntb -x 0
lan_mac=$(mtd_get_mac_binary "Board data" 2)
;;
avm,fritz300e)
lan_mac=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)"))
;;
avm,fritz4020)
lan_mac=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)"))
wan_mac=$(fritz_tffs -n macb -i $(find_mtd_part "tffs (1)"))
;;
dlink,dir-825-b1)
lan_mac=$(mtd_get_mac_text "caldata" 65440)
wan_mac=$(mtd_get_mac_text "caldata" 65460)
;;
dlink,dir-825-c1|\
dlink,dir-835-a1)
lan_mac=$(mtd_get_mac_text "mac" 4)
wan_mac=$(mtd_get_mac_text "mac" 24)
;;
dlink,dir-859-a1|\
nec,wg1200cr|\
wd,mynet-n750)
lan_mac=$(mtd_get_mac_ascii devdata "lanmac")
wan_mac=$(mtd_get_mac_ascii devdata "wanmac")
;;
elecom,wrc-1750ghbk2-i|\
elecom,wrc-300ghbk2-i)
wan_mac=$(macaddr_add "$(mtd_get_mac_binary art 4098)" -2)
;;
engenius,ecb1750)
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
;;
engenius,epg5000|\
iodata,wn-ac1167dgr|\
iodata,wn-ac1600dgr|\
iodata,wn-ac1600dgr2|\
iodata,wn-ag300dgr)
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
wan_mac=$(mtd_get_mac_ascii u-boot-env wanaddr)
;;
engenius,ews511ap)
lan_mac=$(mtd_get_mac_text "u-boot-env" 233)
eth1_mac=$(macaddr_add "$lan_mac" 1)
ucidef_set_interface "eth0" ifname "eth0" protocol "none" macaddr "$lan_mac"
ucidef_set_interface "eth1" ifname "eth1" protocol "none" macaddr "$eth1_mac"
;;
iodata,etg3-r)
lan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
wan_mac=$(macaddr_add "$lan_mac" -1)
;;
jjplus,ja76pf2)
wan_mac=$(fconfig -s -r -d $(find_mtd_part "RedBoot config") -n alias/ethaddr)
lan_mac=$(macaddr_add "$wan_mac" 1)
;;
nec,wg800hp)
lan_mac=$(mtd_get_mac_text board_data 640)
wan_mac=$(mtd_get_mac_text board_data 1152)
;;
netgear,wndr3700|\
netgear,wndr3700v2|\
netgear,wndr3800)
lan_mac=$(macaddr_setbit_la "$(mtd_get_mac_binary art 0)")
;;
phicomm,k2t)
lan_mac=$(k2t_get_mac "lan_mac")
wan_mac=$(k2t_get_mac "wan_mac")
;;
qihoo,c301)
lan_mac=$(mtd_get_mac_ascii devdata lanmac)
wan_mac=$(mtd_get_mac_ascii devdata wanmac)
;;
rosinson,wr818)
wan_mac=$(mtd_get_mac_binary factory 0)
lan_mac=$(macaddr_setbit_la "$wan_mac")
;;
tplink,archer-a7-v5|\
tplink,archer-c7-v4|\
tplink,archer-c7-v5|\
tplink,tl-wr1043nd-v4|\
tplink,tl-wr1043n-v5)
base_mac=$(mtd_get_mac_binary info 8)
wan_mac=$(macaddr_add "$base_mac" 1)
;;
tplink,tl-wr941-v2|\
tplink,tl-wr941n-v7-cn)
base_mac=$(mtd_get_mac_binary u-boot 130048)
wan_mac=$(macaddr_add "$base_mac" 1)
;;
ubnt,routerstation|\
ubnt,routerstation-pro)
wan_mac=$(fconfig -s -r -d $(find_mtd_part "RedBoot config") -n ar7100_esa)
lan_mac=$(macaddr_add "$wan_mac" 1)
;;
wd,mynet-wifi-rangeextender)
lan_mac=$(nvram get et0macaddr)
;;
esac
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
}
board_config_update
board=$(board_name)
ath79_setup_interfaces $board
ath79_setup_macs $board
board_config_flush
exit 0
Reference in a new issue View git blame Copy permalink