b9389186b0
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
FLASH1: 4 MiB NOR
FLASH2: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: Reset
LED: Power, Internet
UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
OTHER: On board with BLE module - by cp210x USB serial chip
On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed
Install via uboot tftp or uboot web failsafe.
By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi
(IPQ40xx) # run lf
By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
186 lines
4.3 KiB
Bash
Executable file
186 lines
4.3 KiB
Bash
Executable file
#!/bin/sh
|
|
#
|
|
# Copyright (c) 2015 The Linux Foundation. All rights reserved.
|
|
# Copyright (c) 2011-2015 OpenWrt.org
|
|
#
|
|
|
|
. /lib/functions/uci-defaults.sh
|
|
. /lib/functions/system.sh
|
|
|
|
ipq40xx_setup_interfaces()
|
|
{
|
|
local board="$1"
|
|
|
|
case "$board" in
|
|
8dev,habanero-dvk|\
|
|
8dev,jalapeno|\
|
|
alfa-network,ap120c-ac|\
|
|
engenius,emr3500|\
|
|
engenius,ens620ext|\
|
|
luma,wrtq-329acn|\
|
|
plasmacloud,pa1200|\
|
|
plasmacloud,pa2200)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
;;
|
|
aruba,ap-303|\
|
|
aruba,ap-365|\
|
|
avm,fritzrepeater-1200|\
|
|
dlink,dap-2610 |\
|
|
engenius,eap1300|\
|
|
engenius,emd1|\
|
|
meraki,mr33|\
|
|
netgear,ex6100v2|\
|
|
netgear,ex6150v2|\
|
|
zyxel,wre6606)
|
|
ucidef_set_interface_lan "eth0"
|
|
;;
|
|
aruba,ap-303h)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "2:lan:1" "3:lan:2" "4:lan:3" "0u@eth1" "5:wan"
|
|
;;
|
|
asus,map-ac2200|\
|
|
cilab,meshpoint-one|\
|
|
edgecore,ecw5211|\
|
|
edgecore,oap100|\
|
|
openmesh,a42|\
|
|
openmesh,a62)
|
|
ucidef_set_interfaces_lan_wan "eth1" "eth0"
|
|
;;
|
|
asus,rt-ac58u|\
|
|
zyxel,nbg6617)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
|
|
;;
|
|
avm,fritzbox-4040|\
|
|
linksys,ea6350v3|\
|
|
linksys,ea8300|\
|
|
linksys,mr8300)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
|
|
;;
|
|
avm,fritzbox-7530)
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
|
|
;;
|
|
avm,fritzrepeater-3000)
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "4:lan:1" "5:lan:2"
|
|
;;
|
|
compex,wpj419|\
|
|
compex,wpj428|\
|
|
engenius,eap2200)
|
|
ucidef_set_interface_lan "eth0 eth1"
|
|
;;
|
|
buffalo,wtr-m2133hp)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "2:lan:3" "3:lan:2" "4:lan:1"
|
|
;;
|
|
cellc,rtl30vw)
|
|
ucidef_set_interface_lan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "3:lan" "4:lan"
|
|
;;
|
|
devolo,magic-2-wifi-next)
|
|
ucidef_set_interface_lan "eth0 eth1 eth2"
|
|
;;
|
|
ezviz,cs-w3-wd1200g-eup)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "0u@eth1" "5:wan"
|
|
;;
|
|
glinet,gl-ap1300 |\
|
|
glinet,gl-b1300 |\
|
|
glinet,gl-s1300)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "3:lan" "4:lan"
|
|
;;
|
|
mobipromo,cm520-79f)
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "3:lan:2" "4:lan:1"
|
|
ucidef_set_interface_wan "eth1"
|
|
;;
|
|
qxwlan,e2600ac-c1 |\
|
|
qxwlan,e2600ac-c2)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "3:lan" "4:lan" "0u@eth1" "5:wan"
|
|
;;
|
|
unielec,u4019-32m)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "0u@eth1" "5:wan"
|
|
;;
|
|
*)
|
|
echo "Unsupported hardware. Network interfaces not initialized"
|
|
;;
|
|
esac
|
|
}
|
|
|
|
ipq40xx_setup_macs()
|
|
{
|
|
local board="$1"
|
|
local lan_mac=""
|
|
local wan_mac=""
|
|
local label_mac=""
|
|
|
|
case "$board" in
|
|
8dev,habanero-dvk)
|
|
label_mac=$(mtd_get_mac_binary "ART" 0x1006)
|
|
;;
|
|
asus,rt-ac58u)
|
|
CI_UBIPART=UBI_DEV
|
|
wan_mac=$(mtd_get_mac_binary_ubi Factory 0x1006)
|
|
lan_mac=$(mtd_get_mac_binary_ubi Factory 0x5006)
|
|
label_mac=$wan_mac
|
|
;;
|
|
cilab,meshpoint-one)
|
|
label_mac=$(mtd_get_mac_binary "ART" 0x1006)
|
|
;;
|
|
devolo,magic-2-wifi-next)
|
|
lan_mac=$(mtd_get_mac_ascii APPSBLENV MacAddress0)
|
|
label_mac=$lan_mac
|
|
;;
|
|
dlink,dap-2610)
|
|
lan_mac=$(mtd_get_mac_ascii bdcfg lanmac)
|
|
label_mac=$lan_mac
|
|
;;
|
|
engenius,eap2200|\
|
|
engenius,emd1)
|
|
lan_mac=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
|
|
label_mac=$lan_mac
|
|
;;
|
|
engenius,emr3500)
|
|
wan_mac=$(mtd_get_mac_ascii 0:APPSBLENV wanaddr)
|
|
lan_mac=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
|
|
label_mac=$wan_mac
|
|
;;
|
|
engenius,ens620ext)
|
|
wan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
|
|
lan_mac=$(macaddr_add "$wan_mac" 1)
|
|
;;
|
|
ezviz,cs-w3-wd1200g-eup)
|
|
label_mac=$(mtd_get_mac_binary "ART" 0x6)
|
|
;;
|
|
linksys,ea6350v3)
|
|
wan_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
|
|
lan_mac=$(macaddr_add "$wan_mac" 1)
|
|
;;
|
|
esac
|
|
|
|
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
|
|
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
|
|
[ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac
|
|
}
|
|
|
|
board_config_update
|
|
board=$(board_name)
|
|
ipq40xx_setup_interfaces $board
|
|
ipq40xx_setup_macs $board
|
|
board_config_flush
|
|
|
|
exit 0
|