4a77a060ab
Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019.
Specification
-------------
- SoC: Qualcomm IPQ4019
- RAM: 512MiB
- Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC)
- Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch)
- Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch)
- Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN)
- LED: 4x white LED, 4x orange LED, 1x blue LED
- USB: 1x USB 3.0 port
- Input: 2x tactile switch, 2x slide switch (2x SP3T)
- Serial console: 115200bps, pinheader JP5 on PCB
- Power: DC 12V 2A
Flash instruction
-----------------
1. Set up a TFTP server (IP address: 192.168.11.10)
2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage"
and put it into the TFTP server directory.
3. Connect the TFTP server and WTR-M2133HP.
4. Hold down the AOSS button, then power on the router.
5. After booting OpenWrt initramfs image, connect to the router by SSH.
6. Transfer "squashfs-nand-factory.ubi" to the router.
7. Execute the following commands.
# ubidetach -p /dev/mtd15
# ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi
# fw_setenv bootcmd bootipq
8. Perform reboot.
Recover to stock firmware
-------------------------
1. Execute the following command.
# fw_setenv bootcmd bootbf
2. Reboot and wait several minutes.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
169 lines
3.9 KiB
Bash
Executable file
169 lines
3.9 KiB
Bash
Executable file
#!/bin/sh
|
|
#
|
|
# Copyright (c) 2015 The Linux Foundation. All rights reserved.
|
|
# Copyright (c) 2011-2015 OpenWrt.org
|
|
#
|
|
|
|
. /lib/functions/uci-defaults.sh
|
|
. /lib/functions/system.sh
|
|
|
|
ipq40xx_setup_interfaces()
|
|
{
|
|
local board="$1"
|
|
|
|
case "$board" in
|
|
8dev,habanero-dvk|\
|
|
8dev,jalapeno|\
|
|
alfa-network,ap120c-ac|\
|
|
engenius,emr3500|\
|
|
engenius,ens620ext)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
;;
|
|
aruba,ap-303|\
|
|
aruba,ap-365|\
|
|
avm,fritzrepeater-1200|\
|
|
dlink,dap-2610 |\
|
|
engenius,eap1300|\
|
|
engenius,emd1|\
|
|
meraki,mr33|\
|
|
netgear,ex6100v2|\
|
|
netgear,ex6150v2|\
|
|
zyxel,wre6606)
|
|
ucidef_set_interface_lan "eth0"
|
|
;;
|
|
aruba,ap-303h)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "2:lan:1" "3:lan:2" "4:lan:3" "0u@eth1" "5:wan"
|
|
;;
|
|
asus,map-ac2200|\
|
|
cilab,meshpoint-one|\
|
|
openmesh,a42|\
|
|
openmesh,a62)
|
|
ucidef_set_interfaces_lan_wan "eth1" "eth0"
|
|
;;
|
|
asus,rt-ac58u|\
|
|
zyxel,nbg6617)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
|
|
;;
|
|
avm,fritzbox-4040|\
|
|
linksys,ea6350v3|\
|
|
linksys,ea8300)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
|
|
;;
|
|
avm,fritzbox-7530)
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
|
|
;;
|
|
avm,fritzrepeater-3000|\
|
|
compex,wpj419|\
|
|
compex,wpj428|\
|
|
engenius,eap2200)
|
|
ucidef_set_interface_lan "eth0 eth1"
|
|
;;
|
|
buffalo,wtr-m2133hp)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "2:lan:3" "3:lan:2" "4:lan:1"
|
|
;;
|
|
cellc,rtl30vw)
|
|
ucidef_set_interface_lan "eth0"
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "3:lan" "4:lan"
|
|
;;
|
|
ezviz,cs-w3-wd1200g-eup)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "0u@eth1" "5:wan"
|
|
;;
|
|
glinet,gl-b1300 |\
|
|
glinet,gl-s1300)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "3:lan" "4:lan"
|
|
;;
|
|
mobipromo,cm520-79f)
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "3:lan:2" "4:lan:1"
|
|
ucidef_set_interface_wan "eth1"
|
|
;;
|
|
qxwlan,e2600ac-c1 |\
|
|
qxwlan,e2600ac-c2)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "3:lan" "4:lan" "0u@eth1" "5:wan"
|
|
;;
|
|
unielec,u4019-32m)
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "0u@eth1" "5:wan"
|
|
;;
|
|
*)
|
|
echo "Unsupported hardware. Network interfaces not initialized"
|
|
;;
|
|
esac
|
|
}
|
|
|
|
ipq40xx_setup_macs()
|
|
{
|
|
local board="$1"
|
|
local lan_mac=""
|
|
local wan_mac=""
|
|
local label_mac=""
|
|
|
|
case "$board" in
|
|
8dev,habanero-dvk)
|
|
label_mac=$(mtd_get_mac_binary "ART" 0x1006)
|
|
;;
|
|
asus,rt-ac58u)
|
|
CI_UBIPART=UBI_DEV
|
|
wan_mac=$(mtd_get_mac_binary_ubi Factory 0x1006)
|
|
lan_mac=$(mtd_get_mac_binary_ubi Factory 0x5006)
|
|
label_mac=$wan_mac
|
|
;;
|
|
cilab,meshpoint-one)
|
|
label_mac=$(mtd_get_mac_binary "ART" 0x1006)
|
|
;;
|
|
dlink,dap-2610)
|
|
lan_mac=$(mtd_get_mac_ascii bdcfg lanmac)
|
|
label_mac=$lan_mac
|
|
;;
|
|
engenius,eap2200|\
|
|
engenius,emd1)
|
|
lan_mac=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
|
|
label_mac=$lan_mac
|
|
;;
|
|
engenius,emr3500)
|
|
wan_mac=$(mtd_get_mac_ascii 0:APPSBLENV wanaddr)
|
|
lan_mac=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
|
|
label_mac=$wan_mac
|
|
;;
|
|
engenius,ens620ext)
|
|
wan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
|
|
lan_mac=$(macaddr_add "$wan_mac" 1)
|
|
;;
|
|
ezviz,cs-w3-wd1200g-eup)
|
|
label_mac=$(mtd_get_mac_binary "ART" 0x6)
|
|
;;
|
|
linksys,ea6350v3)
|
|
wan_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
|
|
lan_mac=$(macaddr_add "$wan_mac" 1)
|
|
;;
|
|
esac
|
|
|
|
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
|
|
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
|
|
[ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac
|
|
}
|
|
|
|
board_config_update
|
|
board=$(board_name)
|
|
ipq40xx_setup_interfaces $board
|
|
ipq40xx_setup_macs $board
|
|
board_config_flush
|
|
|
|
exit 0
|