a0ef42e77c
The Ubiquiti PowerBeam 5AC 500 (PBE-5AC-500) is an outdoor 802.11ac 5 GHz bridge with a radio feed and a dish antenna. Specifications: - SoC: Qualcomm Atheros QCA9558 - RAM: 128 MB DDR2 - Flash: 16 MB SPI NOR (mx25l12805d) - Ethernet: 1x 10/100/1000 Mbps Atheros 8031, 24 Vdc PoE-in - WiFi 5 GHz: QCA988x HW2.0 Ubiquiti target 0x4100016c chip_id 0x043222ff - Buttons: 1x (reset) - LEDs: 1x power, 1x Ethernet, 4x RSSI, all blue - UART: not tested Not supported: - RSSI LEDs (probably through 74HC595 chip) Installation from stock airOS firmware: - Follow instructions for XC-type Ubiquiti devices on OpenWrt wiki at https://openwrt.org/toh/ubiquiti/common Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
201 lines
5.5 KiB
Bash
201 lines
5.5 KiB
Bash
#!/bin/sh
|
|
|
|
[ -e /lib/firmware/$FIRMWARE ] && exit 0
|
|
|
|
. /lib/functions/caldata.sh
|
|
. /lib/functions/k2t.sh
|
|
|
|
board=$(board_name)
|
|
|
|
case "$FIRMWARE" in
|
|
"ath10k/cal-pci-0000:00:00.0.bin")
|
|
case $board in
|
|
avm,fritz1750e)
|
|
caldata_extract "urlader" 0x198a 0x844
|
|
;;
|
|
comfast,cf-wr650ac-v1|\
|
|
comfast,cf-wr650ac-v2|\
|
|
devolo,magic-2-wifi|\
|
|
ubnt,unifiac-lite|\
|
|
ubnt,unifiac-lr|\
|
|
ubnt,unifiac-mesh|\
|
|
ubnt,unifiac-mesh-pro|\
|
|
ubnt,lap-120|\
|
|
ubnt,litebeam-ac-gen2|\
|
|
ubnt,nanobeam-ac|\
|
|
ubnt,nanostation-ac|\
|
|
ubnt,nanostation-ac-loco|\
|
|
ubnt,powerbeam-5ac-500|\
|
|
ubnt,powerbeam-5ac-gen2|\
|
|
ubnt,unifiac-pro|\
|
|
yuncore,a770)
|
|
caldata_extract "art" 0x5000 0x844
|
|
;;
|
|
devolo,dvl1200e|\
|
|
devolo,dvl1200i|\
|
|
devolo,dvl1750c|\
|
|
devolo,dvl1750e|\
|
|
devolo,dvl1750i|\
|
|
devolo,dvl1750x)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) -1)
|
|
;;
|
|
dlink,dir-859-a1)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(mtd_get_mac_ascii devdata "wlan5mac")
|
|
;;
|
|
elecom,wrc-1750ghbk2-i)
|
|
caldata_extract "art" 0x5000 0x844
|
|
;;
|
|
engenius,ecb1750)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(mtd_get_mac_ascii u-boot-env athaddr)
|
|
;;
|
|
engenius,epg5000|\
|
|
iodata,wn-ac1167dgr|\
|
|
iodata,wn-ac1600dgr2|\
|
|
sitecom,wlr-7100)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +1)
|
|
;;
|
|
engenius,ews511ap)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
|
|
;;
|
|
glinet,gl-ar750)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) +1)
|
|
;;
|
|
glinet,gl-x750)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) +2)
|
|
;;
|
|
nec,wg800hp)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(mtd_get_mac_text board_data 0x880)
|
|
;;
|
|
ocedo,koala|\
|
|
ocedo,ursus)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(mtd_get_mac_binary art 0xc)
|
|
;;
|
|
openmesh,om5p-ac-v2)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
|
|
;;
|
|
qihoo,c301)
|
|
caldata_extract "radiocfg" 0x5000 0x844
|
|
ath10k_patch_mac $(mtd_get_mac_ascii devdata wlan5mac)
|
|
;;
|
|
tplink,archer-a7-v5|\
|
|
tplink,archer-c2-v3|\
|
|
tplink,archer-c7-v4|\
|
|
tplink,archer-c7-v5|\
|
|
tplink,archer-c25-v1)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary info 0x8) -1)
|
|
;;
|
|
tplink,archer-c5-v1|\
|
|
tplink,archer-c7-v2)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary u-boot 0x1fc00) -1)
|
|
;;
|
|
tplink,archer-d50-v1)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary romfile 0xf100) +2)
|
|
;;
|
|
tplink,archer-d7-v1|\
|
|
tplink,archer-d7b-v1)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary romfs 0xf100) +2)
|
|
;;
|
|
tplink,re350k-v1)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary config 0x10008) +2)
|
|
;;
|
|
tplink,re355-v1|\
|
|
tplink,re450-v1)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -2)
|
|
;;
|
|
tplink,re450-v2)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary info 0x8) +1)
|
|
;;
|
|
tplink,tl-wr902ac-v1)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary tplink 0x8) -1)
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/cal-pci-0000:01:00.0.bin")
|
|
case $board in
|
|
sitecom,wlr-8100)
|
|
caldata_extract "art" 0x5000 0x844
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +1)
|
|
;;
|
|
esac
|
|
;;
|
|
"ath10k/pre-cal-pci-0000:00:00.0.bin")
|
|
case $board in
|
|
comfast,cf-e313ac)
|
|
caldata_extract "art" 0x5000 0x2f20
|
|
ath10k_patch_mac $(mtd_get_mac_binary art 0x6)
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
rm /lib/firmware/ath10k/QCA9888/hw2.0/board-2.bin
|
|
;;
|
|
comfast,cf-e560ac|\
|
|
comfast,cf-ew72|\
|
|
comfast,cf-wr752ac-v1)
|
|
caldata_extract "art" 0x5000 0x2f20
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) +2)
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
rm /lib/firmware/ath10k/QCA9888/hw2.0/board-2.bin
|
|
;;
|
|
dlink,dir-842-c1|\
|
|
dlink,dir-842-c2|\
|
|
dlink,dir-842-c3|\
|
|
nec,wg1200cr)
|
|
caldata_extract "art" 0x5000 0x2f20
|
|
ath10k_patch_mac $(mtd_get_mac_ascii devdata wlan5mac)
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
;;
|
|
netgear,ex6400|\
|
|
netgear,ex7300)
|
|
caldata_extract "caldata" 0x5000 0x2f20
|
|
ath10k_patch_mac $(mtd_get_mac_binary caldata 0xc)
|
|
;;
|
|
phicomm,k2t)
|
|
caldata_extract "art" 0x5000 0x2f20
|
|
ath10k_patch_mac $(k2t_get_mac "5g_mac")
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
;;
|
|
tplink,archer-c58-v1|\
|
|
tplink,archer-c59-v1|\
|
|
tplink,archer-c59-v2|\
|
|
tplink,archer-c60-v1|\
|
|
tplink,archer-c60-v2|\
|
|
tplink,archer-c60-v3|\
|
|
tplink,archer-c6-v2|\
|
|
tplink,archer-c6-v2-us)
|
|
caldata_extract "art" 0x5000 0x2f20
|
|
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary mac 0x8) -1)
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
;;
|
|
yuncore,a782|\
|
|
yuncore,xd4200)
|
|
caldata_extract "art" 0x5000 0x2f20
|
|
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
|
|
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
|
|
;;
|
|
esac
|
|
;;
|
|
*)
|
|
exit 1
|
|
;;
|
|
esac
|