635f111148
In ath79, for several SoCs the console bootargs are defined to the very same value in every device's DTS. Consolidate these definitions in the SoC dtsi files and drop further redundant definitions elsewhere. The only device without any bootargs set has been OpenMesh OM5P-AC V2. This will now inherit the setting from qca955x.dtsi Note that while this tidies up master a lot, it might develop into a frequent pitfall for backports. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
136 lines
2.1 KiB
Text
136 lines
2.1 KiB
Text
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
|
|
#include "qca955x.dtsi"
|
|
|
|
/ {
|
|
compatible = "mikrotik,routerboard-wap-g-5hact2hnd", "qca,qca9556";
|
|
model = "MikroTik RouterBOARD wAP G-5HacT2HnD";
|
|
|
|
aliases {
|
|
mdio-gpio1 = &mdio2;
|
|
serial0 = &uart;
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
|
|
debounce-interval = <60>;
|
|
};
|
|
};
|
|
|
|
mdio2: mdio {
|
|
compatible = "virtual,mdio-gpio";
|
|
|
|
gpios = <&gpio 12 GPIO_ACTIVE_HIGH>, /* MDC */
|
|
<&gpio 11 GPIO_ACTIVE_HIGH>; /* MDIO */
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
phy0: ethernet-phy@0 {
|
|
reg = <0>;
|
|
device_type = "ethernet-phy";
|
|
|
|
phy-mode = "sgmii";
|
|
|
|
at803x-override-sgmii-link-check;
|
|
};
|
|
};
|
|
};
|
|
|
|
ð1 {
|
|
status = "okay";
|
|
|
|
pll-data = <0x03000101 0x80000101 0x80001313>;
|
|
phy-handle = <&phy0>;
|
|
|
|
qca955x-sgmii-fixup;
|
|
|
|
gmac-config {
|
|
device = <&gmac>;
|
|
};
|
|
};
|
|
|
|
&spi {
|
|
status = "okay";
|
|
|
|
num-cs = <1>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <40000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "RouterBoot";
|
|
reg = <0x0 0x20000>;
|
|
read-only;
|
|
compatible = "mikrotik,routerboot-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "bootloader1";
|
|
reg = <0x0 0x0>;
|
|
read-only;
|
|
};
|
|
|
|
hard_config: hard_config {
|
|
read-only;
|
|
};
|
|
|
|
bios {
|
|
size = <0x1000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@10000 {
|
|
label = "bootloader2";
|
|
reg = <0x10000 0x0>;
|
|
read-only;
|
|
};
|
|
|
|
soft_config {
|
|
label = "soft_config";
|
|
};
|
|
};
|
|
|
|
partition@20000 {
|
|
compatible = "mikrotik,minor";
|
|
label = "firmware";
|
|
reg = <0x020000 0xfe0000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart {
|
|
status = "okay";
|
|
};
|
|
|
|
&wmac {
|
|
status = "okay";
|
|
|
|
qca,no-eeprom;
|
|
};
|
|
|
|
&pcie0 {
|
|
status = "okay";
|
|
|
|
wifi@0,0 {
|
|
compatible = "qcom,ath10k";
|
|
reg = <0 0 0 0 0>;
|
|
};
|
|
};
|