Difuse/difos
2
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity Actions
difos/target/linux/ramips/dts
History
Simon Quigley 9f0e233576 ramips: add support for DLINK DWR-922-E2 
Very similar to the DWR-921-C1, except has a telephony/RJ11 port (not
sure if supported, I didn't try), wireless router with QMI LTE embedded
modem is based on the MT7620N SoC.

Specification:

  * MediaTek MT7620N (580 Mhz)
  * 64 MB of RAM
  * 16 MB of FLASH
  * 802.11bgn radio
  * 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
  * 2x external, detachable (LTE) antennas
  * UART header on PCB (57600 8n1)
  * 6x LED (GPIO-controlled)
  * 1x bi-color Signal Strength LED (GPIO-controlled)
  * 2x button
  * JBOOT bootloader

The status led has been assigned to the dwr-922-e2:green:signalstrength
(lte signal strength) led. At the end of the boot it is switched off and
is available for lte operation. Works correctly also during sysupgrade
operation.

Installation:
Apply factory image via d-link http web-gui, or via recovery interface:

How to recover/revert to OEM firmware:
1.) Push and hold the reset button and turn on the power. Wait until all
    LEDs start rapidly blinking (~10sec.)
2.) DHCP should give you an IP in the 192.168.123.0/24 subnet, or set
    one manually
3.) Upload original factory image via JBOOT http interface at IP
    192.168.123.254
4.) If http doesn't work, it can be done with curl command:
      curl -F FN=@XXXXX.bin http://192.168.123.254/upg
    where XXXXX.bin is name of firmware file.
5.) You can optionally telnet to 192.168.123.254 before or during the
    upload and it will report the flashing status, memory address etc.
6.) Once web UI and/or telnet says "Success", power cycle the router, or
    type "reboot" into the telnet session.

Signed-off-by: Simon Quigley <squigley@squigley.net>
[squashed commits, word wrap commit message, rename signal strenght led
name to match what is used for the DWR-921-C1 since they share the led
configuration, add label referenced in the aliases node]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-12-29 16:03:30 +01:00
..
3G-6200N.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
3G-6200NL.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
3G150B.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
3G300M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
11ACNAS.dts ramips: set usb led trigger via devicetree 2018-10-07 11:34:18 +02:00
A5-V11.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
AC1200RM.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
AI-BR100.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
AIR3GII.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ALL0256N-4M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ALL0256N-8M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ALL0256N.dtsi ramips: fix dtc warnings 2018-08-04 08:39:35 +02:00
ALL5002.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ALL5003.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
AP-MT7621A-V60.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
AR670W.dts ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
AR725W.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ArcherC2-v1.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ArcherC20i.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ArcherC20v1.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ArcherC20v4.dts ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
ArcherC50.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ArcherC50V3.dts ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
ArcherMR200.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ASL26555-8M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ASL26555-16M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ASL26555.dtsi ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
ATP-52B.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
AWAPN2403.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
AWM002-EVB-4M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
AWM002-EVB-8M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
AWM002-EVB.dtsi ramips: fix dtc warnings 2018-08-04 08:39:35 +02:00
AWUSFREE1.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
BC2.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
BDCOM-WAP2100-SK.dts ramips: bdcom-wap2100: Change DTS license to GPL-2.0-or-later OR MIT 2018-11-29 13:15:44 +01:00
BOCCO.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
BR-6475ND.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
BR-6478AC-V2.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
BROADWAY.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
C108.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
CARAMBOLA.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
CF-WR800N.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
CreativeBox-v1.dts ramips: add support for CreativeBox v1 2018-12-28 12:45:23 +01:00
CS-QR10.dts ramips: mt7620: disable PCIe if nothing is attached 2018-12-03 15:34:56 +01:00
CY-SWR1100.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
D105.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
D240.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
DAP-1350.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
DAP-1522-A1.dts ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
DB-WRT01.dts ramips: mt7620: disable PCIe if nothing is attached 2018-12-03 15:34:56 +01:00
DCH-M225.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
DCS-930.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
DCS-930L-B1.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
DIR-300-B1.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
DIR-300-B7.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
DIR-320-B1.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
DIR-600-B1.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
DIR-610-A1.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
DIR-615-D.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
DIR-615-H1.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
DIR-620-A1.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
DIR-620-D1.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
DIR-645.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
DIR-810L.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
DIR-860L-B1.dts ramips: fix firmware compatible string for dir860l-b1 2018-12-08 14:18:42 +01:00
DUZUN-DM06.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
DWR-116-A1.dts ramips: specify "firmware" partition format in JBOOT devices 2018-11-30 00:22:04 +01:00
DWR-118-A1.dts ramips: add support for D-Link DWR-118-A1 2018-12-03 15:34:56 +01:00
DWR-118-A2.dts ramips: specify "firmware" partition format in JBOOT devices 2018-11-30 00:22:04 +01:00
DWR-512-B.dts ramips: fix dtc compiler warnings 2018-12-06 12:17:25 +01:00
DWR-921-C1.dts ramips: specify "firmware" partition format in JBOOT devices 2018-11-30 00:22:04 +01:00
DWR-922-E2.dts ramips: add support for DLINK DWR-922-E2 2018-12-29 16:03:30 +01:00
E1700.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
elecom_wrc-gst.dtsi ramips: add SPDX license identifier into some dts,dtsi 2018-12-28 12:45:23 +01:00
ESR-9753.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
EW1200.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
EX2700.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
EX3700.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
F5D8235_V1.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
F5D8235_V2.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
F7C027.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
FIREWRT.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
FONERA20N.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
FREESTATION5.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
GB-PC1.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
GB-PC2.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
GL-MT300A.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
GL-MT300N-V2.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
GL-MT300N.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
GL-MT750.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
HC5X61.dtsi ramips: several fixes for HC5x61 2018-12-15 20:02:07 +01:00
HC5661.dts ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
HC5661A.dts ramips: disable sdhc for HC5661A 2018-12-06 12:17:25 +01:00
HC5761.dts ramips: several fixes for HC5x61 2018-12-15 20:02:07 +01:00
HC5861.dts ramips: several fixes for HC5x61 2018-12-15 20:02:07 +01:00
HC5861B.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
HC5962.dts ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
HG255D.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
HLKRM04.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
HPM.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
HT-TM02.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
HW550-3G.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
IP2202.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
JHR-N805R.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
JHR-N825R.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
JHR-N926R.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
K2G.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
K2P.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ki_rb.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
kn.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
kn_rc.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
kn_rf.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
kng_rc.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
LINKIT7688.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
LR-25G001.dts ramips: specify "firmware" partition format in JBOOT devices 2018-11-30 00:22:04 +01:00
M2M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
M3.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
M4-4M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
M4-8M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
M4.dtsi ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
MAC1200RV2.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
MicroWRT.dts ramips: mt7620: disable PCIe if nothing is attached 2018-12-03 15:34:56 +01:00
MINIEMBPLUG.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
MINIEMBWIFI.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
MIR3G.dts ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
MIWIFI-MINI.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
MIWIFI-NANO.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
MLW221.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
MLWG2.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
MOFI3500-3GN.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
MPRA1.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
MPRA2.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
MR-102N.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
MT7620a.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
mt7620a.dtsi ramips: fix dtc compiler warnings 2018-12-06 12:17:25 +01:00
MT7620a_MT7530.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
MT7620a_MT7610e.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
MT7620a_V22SG.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
mt7620n.dtsi ramips: fix dtc compiler warnings 2018-12-06 12:17:25 +01:00
MT7621.dts ramips: move partitions into partition table node 2018-08-04 08:39:35 +02:00
mt7621.dtsi ramips: fix dtc compiler warnings 2018-12-06 12:17:25 +01:00
MT7628.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
mt7628an.dtsi ramips: fix dtc compiler warnings 2018-12-06 12:17:25 +01:00
MZK-750DHP.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
MZK-DP150N.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
MZK-EX300NP.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
MZK-EX750NP.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
MZK-W300NH2.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
MZK-WDPR.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
NA930.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
NBG-419N.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
NBG-419N2.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
NCS601W.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
Newifi-D1.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
Newifi-D2.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
NIXCORE-8M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
NIXCORE-16M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
NIXCORE.dtsi ramips: fix whitespace and comment issues in dts 2018-08-04 08:39:35 +02:00
NW718.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
OMEGA2.dts ramips: fix Omega2 compatible string 2017-12-29 22:32:34 +01:00
OMEGA2.dtsi ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
OMEGA2P.dts ramips: fix Omega2 compatible string 2017-12-29 22:32:34 +01:00
OY-0001.dts ramips: mt7620: disable PCIe if nothing is attached 2018-12-03 15:34:56 +01:00
PBR-D1.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
PBR-M1.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
PSG1208.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
PSG1218.dtsi ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
PSG1218A.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
PSG1218B.dts treewide: dts: Remove default-state=off property from all gpio LED nodes 2018-12-17 08:16:28 +01:00
PSR-680W.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
PWH2004.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
PX-4885-4M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
PX-4885-8M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
PX-4885.dtsi ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
R6120.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
R6220.dts ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
R6350.dts ramips: add SPDX license identifier into some dts,dtsi 2018-12-28 12:45:23 +01:00
RB750Gr3.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
RBM11G.dts ramips: mt7621: specify "firmware" partition format for remaining devices 2018-12-13 13:39:56 +01:00
RBM33G.dts ramips: mt7621: specify "firmware" partition format for remaining devices 2018-12-13 13:39:56 +01:00
RE350.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
RE6500.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
RP-N53.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
RT-AC51U.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
RT-G32-B1.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
RT-N10-PLUS.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
RT-N12-PLUS.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
RT-N13U.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
RT-N14U.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
RT-N15.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
RT-N56U.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
rt2880.dtsi ramips: fix dtc compiler warnings 2018-12-06 12:17:25 +01:00
rt3050.dtsi ramips: fix dtc compiler warnings 2018-12-06 12:17:25 +01:00
rt3352.dtsi ramips: fix dtc compiler warnings 2018-12-06 12:17:25 +01:00
rt3883.dtsi ramips: fix dtc compiler warnings 2018-12-06 12:17:25 +01:00
rt5350.dtsi ramips: fix dtc compiler warnings 2018-12-06 12:17:25 +01:00
RT5350F-OLINUXINO-EVB.dts ramips: introduce RT5350F-OLINUXINO.dtsi 2017-09-28 09:20:36 +02:00
RT5350F-OLINUXINO.dts ramips: introduce RT5350F-OLINUXINO.dtsi 2017-09-28 09:20:36 +02:00
RT5350F-OLINUXINO.dtsi ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
RUT5XX.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
SAP-G3200U3.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
SK-WB8.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
SKW92A.dts ramips: improve Skylab SKW92A support 2018-11-26 15:54:22 +01:00
SL-R7205.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
TEW-638APB-V2.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
TEW-691GR.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
TEW-692GR.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
TEW-714TRU.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
Timecloud.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
TINY-AC.dts ramips: mt7620: add missing pci wifi nodes to dts files 2018-12-03 15:34:56 +01:00
TL-MR3020V3.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
TL-MR3420V5.dts ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
TL-WA801NDV5.dts ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
TL-WR840NV4.dts ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
TL-WR840NV5.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
TL-WR841NV13.dts ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
TL-WR842NV5.dts ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
TL-WR902ACV3.dts ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
TPLINK-8M.dtsi ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
U25AWF-H1.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
U35WF.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
U7621-06-256M-16M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
U7621-06-512M-64M.dts ramips: add support for UniElec U7621-06-512M-64M variant 2018-11-28 01:11:38 +01:00
U7621-06.dtsi ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
U7628-01-128M-16M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
U7628-01.dtsi ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
UBNT-ER-e50.dtsi ramips: fix dtc compiler warnings 2018-12-06 12:17:25 +01:00
UBNT-ERX-SFP.dts ramips: add missing soc compatibles to dts 2018-01-09 22:05:46 +01:00
UBNT-ERX.dts ramips: add support for Ubiquiti EdgeRouter X-SFP 2017-06-07 06:33:33 +02:00
UR-326N4G.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
UR-336UN.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
V11STFE.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
V22RW-2X2.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
VAR11N-300.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
VOCORE-8M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
VOCORE-16M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
VOCORE.dtsi ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
VOCORE2.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
VOCORE2.dtsi ramips: backport MT7628 pinmux fixes 2017-11-22 08:21:52 +01:00
VOCORE2LITE.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
VR500.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
W06.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
W150M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
W306R_V20.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
W502U.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
W2914NSV2.dts ramips: set usb led trigger via devicetree 2018-10-07 11:34:18 +02:00
W2914NSV2.dtsi ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WCR-1166DS.dts ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
WCR150GN.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WD03.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WE1026-5G-16M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WE1026-5G.dtsi ramips: set usb led trigger via devicetree 2018-10-07 11:34:18 +02:00
WF-2881.dts ramips: mt7621: specify "firmware" partition format for remaining devices 2018-12-13 13:39:56 +01:00
WHR-300HP2.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WHR-600D.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WHR-1166D.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WHR-G300N.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WIDORA-NEO-16M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WIDORA-NEO-32M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WIDORA-NEO.dtsi ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
WITI-256M.dts ramips: add support for mqmaker witi 512mb version 2018-05-07 18:54:23 +02:00
WITI-512M.dts ramips: add support for mqmaker witi 512mb version 2018-05-07 18:54:23 +02:00
WITI.dtsi ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WIZARD8800.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WIZFI630A.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WL-330N.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WL-330N3G.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WL-351.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WL-WN570HA1.dts ramips: add support for Wavlink WL-WN570HA1 2018-11-28 00:50:35 +01:00
WL-WN575A3.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WLI-TX4-AG300N.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WLR-6000.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WMDR-143N.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WMR-300.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WN-AX1167GR.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WN-GX300GR.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WN3000RPV3.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WNCE2001.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WNDR3700V5.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WR512-3GN-4M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WR512-3GN-8M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WR512-3GN.dtsi ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
WR1200JS.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WR1201.dts ramips: add support for MTC Wireless Router WR1201 2018-11-30 00:20:28 +01:00
WR6202.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WRC-1167GHBK2-S.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WRC-1900GST.dts ramips: add SPDX license identifier into some dts,dtsi 2018-12-28 12:45:23 +01:00
WRC-2533GST.dts ramips: add support for ELECOM WRC-1900GST 2018-08-23 22:42:09 +02:00
WRH-300CR.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WRTNODE.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WRTNODE2.dtsi ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WRTNODE2P.dts ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
WRTNODE2R.dts ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
WSR-600.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WSR-1166.dts ramips: mt7621: specify "firmware" partition format for remaining devices 2018-12-13 13:39:56 +01:00
WT1520-4M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WT1520-8M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WT1520.dtsi ramips: fix dtc warnings 2018-08-04 08:39:35 +02:00
WT3020-4M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WT3020-8M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
WT3020.dtsi ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
WZR-AGL300NH.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
X5.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
X8.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
XDXRN502J.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
Y1.dts ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
Y1.dtsi ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
Y1S.dts ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
YOUKU-YK1.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ZBT-APE522II.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ZBT-CPE102.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ZBT-WA05.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ZBT-WE826-16M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ZBT-WE826-32M.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ZBT-WE826.dtsi ramips: add support for indicating the boot state using multiple leds 2018-10-07 11:34:18 +02:00
ZBT-WE1226.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ZBT-WE1326.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ZBT-WE2026.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ZBT-WE3526.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ZBT-WG2626.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ZBT-WG3526-16M.dts ramips: mt7621: add compatible strings 2017-07-29 09:24:32 +02:00
ZBT-WG3526-32M.dts ramips: mt7621: add compatible strings 2017-07-29 09:24:32 +02:00
ZBT-WG3526.dtsi ramips: mt7621: fix 5GHz WiFi LED on ZBT WG3526 2018-12-29 12:35:47 +01:00
ZBT-WR8305RT.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ZL5900V2.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00
ZTE-Q7.dts ramips: specify "firmware" partition format 2018-11-29 13:15:44 +01:00