difos/target/linux/bcm63xx/base-files/etc/uci-defaults/09_fix_crc
Daniele Castro 59c2f9eaad bcm63xx: add support for Technicolor TG582n
Technicolor TG582n has a similar PCB as the OpenWrt's ADB P.DG A4001N1
with LEDs connected to different GPIO PINs in active low configuration.

Hardware:
* Board ID: DANT-1
* SoC: Broadcom BCM6328 (rev b0) @ 320MHz, CPU BMIPS4350
* RAM DDR2: 64 Mbyte - Winbond W9751G6KB-25
* Serial flash: 16 Mbyte - MXIC MX25L6445EMI
* Ethernet: 4x Ethernet 10/100 baseT
* Wifi 2.4GHz: Broadcom Corporation BCM43227 Wireless Network Adapter (rev 30)
* LEDs: 2x Power, 1x Ethernet, 1x Broadband, 2x Wi-Fi, 2x WPS, 4x ethernet
* Buttons: 1x Reset, 1x WPS, 1x WiFi
* UART: 1x TTL 115200n8, VCC GND TX RX, on J3 connector (short R62 and R63)

Installation via CFE:
* Stock CFE has to be overwritten with a generic 6328 one that can upload
  .bin images with no signature check (cfe6328_configured.bin)
* Connect a serial port to the board
* Stop the CFE boot process after power on by pressing enter
* Set static IP 192.168.2.10 and subnet mask 255.255.255.0
* Navigate to http://192.168.2.50/
* Upload the OpenWrt image file

PCB:   |GPIO:   |TG582n:

LED2R  |488(08) |red    Power
LED2G  |484(04) |green  Power

LED10R |486(06) |
LED13G |485(05) |green  Ethernet

LED11R |494(14) |
LED14G |491(11) |green  Broadband

LED5R  |487(07) |red    Internet
LED5G  |481(01) |green  Internet

LED12R |498(18) |
LED12G |499(19) |

LED6R  |482(02) |red    Wi-Fi
LED6G  |483(03) |green  Wi-Fi

LED7R  |490(10) |red    WPS
LED7G  |489(09) |green  WPS

LED4   |508(28) |ethernet port 4
LED3   |507(27) |ethernet port 3

LED9   |506(26) |ethernet port 2
LED8   |505(25) |ethernet port 1

SW3    |503(23) |key Reset

SW5    |504(24) |key WPS

SW4    |495(15) |key Wi-Fi

SW6    |493(13) |

SW1    |492(12) |

Signed-off-by: Daniele Castro <danielecastro@hotmail.it>
[Fix base-files, refresh patch]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2020-12-06 19:17:41 +01:00

45 lines
815 B
Text

#
# Copyright (C) 2007 OpenWrt.org
#
. /lib/functions.sh
do_fixcrc() {
mtd fixtrx linux
}
case "$(board_name)" in
actiontec,r1000h|\
adb,a4001n|\
adb,a4001n1|\
adb,pdg-a4001n-a-000-1a1-ax|\
adb,pdg-a4101n-a-000-1a1-ae|\
brcm,bcm96328avng|\
brcm,bcm963281tan|\
bt,voyager-2110|\
bt,voyager-2500v-bb|\
comtrend,ar-5315u|\
comtrend,ar-5381u|\
comtrend,ar-5387un|\
comtrend,vr-3025u|\
comtrend,vr-3025un|\
comtrend,vr-3026e|\
comtrend,wap-5813n|\
comtrend,ct-6373|\
d-link,dsl-274xb-f1|\
dynalink,rta770bw|\
dynalink,rta770w|\
huawei,echolife-hg622|\
netgear,evg2000|\
nucom,r5010un-v2|\
observa,vh4032n|\
t-com,speedport-w-303v|\
technicolor,tg582n|\
technicolor,tg582n-telecom-italia|\
telsey,cpva502plus|\
telsey,cpva642|\
telsey,magic|\
zyxel,p870hw-51a-v2)
do_fixcrc
;;
esac