6da3194127
This patch adds supports for the NETGEAR R6200 V1 This device is mainlined in Linux as of 5.4 Specification: - SOC: Broadcom BCM4718A1 (480 MHz) - Flash: 16MB (Macronix MX25L128) - RAM: 128MB DDR2 - SWITCH: BCM53125 - Ethernet: 5x GE (1 WAN + 4 LAN, Inverted order) - WLAN 2.4G: In SOC - WLAN 5GHz: miniPCIe card, BCM4352 (ID: 4360) - USB: 1x USB 2.0 port (Type A) - Buttons: Reset, WLAN, WPS - LED: Amber for Power, others need a workaround - UART: 1x UART on PCB LED Issues: They are controlled by a 74HC164 via bit banging(GPIO 6/7) Firmware Install Instructions ============================= Using the device specific .chk, use that file to perform a normal device upgrade in the OEM admin page. Signed-off-by: Edward Matijevic <motolav@gmail.com>
211 lines
5.3 KiB
Bash
Executable file
211 lines
5.3 KiB
Bash
Executable file
#!/bin/sh /etc/rc.common
|
|
# Copyright (C) 2006-2015 OpenWrt.org
|
|
|
|
. /lib/functions/system.sh
|
|
. /lib/functions/uci-defaults.sh
|
|
|
|
configure_by_vlanports() {
|
|
local vlan0ports="$(nvram get vlan0ports)"
|
|
local vlan1ports="$(nvram get vlan1ports)"
|
|
local vlan2ports="$(nvram get vlan2ports)"
|
|
local cpuport="$(swconfig dev switch0 help 2>/dev/null | sed -ne "s|.*cpu @ \([0-9]*\).*|\1|p")"
|
|
|
|
if [ "${vlan0ports:0:9}" = "0 1 2 3 8" -a "${vlan1ports:0:3}" = "4 8" -a ${cpuport:-0} -eq 8 ] || \
|
|
[ "${vlan1ports:0:9}" = "0 1 2 3 8" -a "${vlan2ports:0:3}" = "4 8" -a ${cpuport:-0} -eq 8 ] || \
|
|
[ "${vlan2ports:0:9}" = "0 1 2 3 8" -a "${vlan1ports:0:3}" = "4 8" -a ${cpuport:-0} -eq 8 ];
|
|
then
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "8@eth0"
|
|
|
|
elif [ "${vlan0ports:0:9}" = "1 2 3 4 8" -a "${vlan1ports:0:3}" = "0 8" -a ${cpuport:-0} -eq 8 ] || \
|
|
[ "${vlan1ports:0:9}" = "1 2 3 4 8" -a "${vlan2ports:0:3}" = "0 8" -a ${cpuport:-0} -eq 8 ] || \
|
|
[ "${vlan2ports:0:9}" = "1 2 3 4 8" -a "${vlan1ports:0:3}" = "0 8" -a ${cpuport:-0} -eq 8 ];
|
|
then
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "8@eth0"
|
|
|
|
elif [ "${vlan0ports:0:9}" = "0 1 2 3 5" -a "${vlan1ports:0:3}" = "4 5" -a ${cpuport:-0} -eq 5 ] || \
|
|
[ "${vlan1ports:0:9}" = "0 1 2 3 5" -a "${vlan2ports:0:3}" = "4 5" -a ${cpuport:-0} -eq 5 ] || \
|
|
[ "${vlan2ports:0:9}" = "0 1 2 3 5" -a "${vlan1ports:0:3}" = "4 5" -a ${cpuport:-0} -eq 5 ];
|
|
then
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "5@eth0"
|
|
|
|
elif [ "${vlan0ports:0:9}" = "1 2 3 4 5" -a "${vlan1ports:0:3}" = "0 5" -a ${cpuport:-0} -eq 5 ] || \
|
|
[ "${vlan1ports:0:9}" = "1 2 3 4 5" -a "${vlan2ports:0:3}" = "0 5" -a ${cpuport:-0} -eq 5 ] || \
|
|
[ "${vlan2ports:0:9}" = "1 2 3 4 5" -a "${vlan1ports:0:3}" = "0 5" -a ${cpuport:-0} -eq 5 ];
|
|
then
|
|
ucidef_add_switch "switch0" \
|
|
"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "5@eth0"
|
|
|
|
else
|
|
logger -t "01_network" "Unable to determine network configuration"
|
|
ucidef_set_interface_lan "eth0"
|
|
fi
|
|
}
|
|
|
|
configure_by_boardnum() {
|
|
local boardnum="$1"
|
|
|
|
case "$boardnum" in
|
|
# WAP54G, Sitecom WL-105b
|
|
"2" | \
|
|
"1024")
|
|
ucidef_set_interface_lan "eth0"
|
|
;;
|
|
|
|
# Generic detection fallback
|
|
*)
|
|
configure_by_vlanports
|
|
;;
|
|
esac
|
|
}
|
|
|
|
configure_by_boardtype() {
|
|
local boardtype="$1"
|
|
local boardnum="$2"
|
|
|
|
case "$boardtype" in
|
|
"bcm94710r4")
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
;;
|
|
|
|
"0x0467")
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "5@eth0"
|
|
;;
|
|
|
|
"0x042f" | \
|
|
"0x0472")
|
|
# WL-500gP
|
|
if [ "$boardnum" = "45" ]; then
|
|
ucidef_add_switch "switch0" \
|
|
"0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "5@eth0"
|
|
|
|
# Generic BCM94704
|
|
else
|
|
ucidef_set_interface_wan "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:lan" "5@eth0"
|
|
|
|
# MAC addresses on 4704 tend to be screwed up. Add a workaround here
|
|
local mac="$(nvram get et0macaddr)"
|
|
local pat="[0-9a-fA-F][0-9a-fA-F]:[0-9a-fA-F][0-9a-fA-F]"
|
|
pat="$pat:[0-9a-fA-F][0-9a-fA-F]:[0-9a-fA-F][0-9a-fA-F]"
|
|
pat="$pat:[0-9a-fA-F][0-9a-fA-F]:[0-9a-fA-F][0-9a-fA-F]"
|
|
|
|
case "$mac" in
|
|
$pat)
|
|
ucidef_set_interface_macaddr "lan" "$mac"
|
|
ucidef_set_interface_macaddr "wan" "$(macaddr_add "$mac" 1)"
|
|
;;
|
|
esac
|
|
fi
|
|
;;
|
|
|
|
# Buffalo WBR-B11 and Buffalo WBR-G54
|
|
"bcm94710ap")
|
|
ucidef_set_interface_wan "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:lan" "5@eth0"
|
|
;;
|
|
|
|
*)
|
|
configure_by_boardnum "$boardnum"
|
|
;;
|
|
esac
|
|
}
|
|
|
|
configure_by_model() {
|
|
local model="$1"
|
|
local boardtype="$2"
|
|
local boardnum="$3"
|
|
|
|
# Netgear WGT634U exception
|
|
if grep -sqE 'mtd0: 000(6|a)0000' /proc/mtd; then
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "5@eth0"
|
|
return
|
|
fi
|
|
|
|
case "$model" in
|
|
"Asus WLHDD" | \
|
|
"Asus WL300G")
|
|
ucidef_set_interface_lan "eth1"
|
|
;;
|
|
|
|
"Asus WL330GE")
|
|
ucidef_add_switch "switch0" "4:lan" "5t@eth0"
|
|
;;
|
|
|
|
"Asus WL500G" | \
|
|
"Microsoft MN-700")
|
|
ucidef_set_interfaces_lan_wan "eth0" "eth1"
|
|
;;
|
|
|
|
"Asus WL500GP V2")
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "4:wan" "5@eth0"
|
|
;;
|
|
|
|
"Asus RT-N12"* | \
|
|
"Buffalo WHR-G125" | \
|
|
"D-Link DIR-330" | \
|
|
"Motorola WR850G" | \
|
|
"Siemens SE505 V2")
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "5@eth0"
|
|
;;
|
|
|
|
"Asus WL700")
|
|
ucidef_add_switch "switch0" \
|
|
"0:wan" "1:lan" "2:lan" "3:lan" "4:lan" "5@eth0"
|
|
;;
|
|
|
|
"Asus WL500W" | \
|
|
"Dell TrueMobile 2300")
|
|
ucidef_set_interface_wan "eth1"
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan" "1:lan" "2:lan" "3:lan" "5@eth0"
|
|
;;
|
|
|
|
"Asus RT-N16"* | \
|
|
"Linksys E3000 V1" | \
|
|
"Netgear WNR3500 V2" | \
|
|
"Netgear WNR3500L")
|
|
ucidef_add_switch "switch0" \
|
|
"0:wan" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "8@eth0"
|
|
;;
|
|
|
|
"Netgear R6200 V1")
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "4:wan" "8@eth0"
|
|
;;
|
|
|
|
"Netgear WN2500RP V1")
|
|
ucidef_add_switch "switch0" \
|
|
"0:lan:4" "1:lan:3" "2:lan:2" "3:lan:1" "5@eth0"
|
|
;;
|
|
|
|
*)
|
|
configure_by_boardtype "$boardtype" "$boardnum"
|
|
;;
|
|
esac
|
|
}
|
|
|
|
|
|
model="$(cat /tmp/sysinfo/model)"
|
|
boardtype="$(board_name)"
|
|
|
|
case "$boardtype" in
|
|
*:*)
|
|
boardnum="${boardtype##*:}"
|
|
boardtype="${boardtype%:*}"
|
|
;;
|
|
esac
|
|
|
|
board_config_update
|
|
|
|
configure_by_model "$model" "$boardtype" "$boardnum"
|
|
|
|
board_config_flush
|