Difuse/difos
2
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity Actions
difos/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
Davide Fioravanti 213250b56b ath79: add support for TP-Link Archer D7/D7b v1 
TP-Link Archer D7 v1 is a dual-band AC1750 router + modem.
The router section is based on Qualcomm/Atheros QCA9558 + QCA9880.
The "DSL" section is based on BCM6318 but it's currently not supported.

The Archer D7b seems to differ from the Archer D7 only in the
partition table.

Router section - Specification:

775/650/258 MHz (CPU/DDR/AHB)
128 MB of RAM (DDR2)
16 MB of FLASH (SPI NOR)
3T3R 2.4 GHz
3T3R 5 GHz
4x 10/100/1000 Mbps Ethernet
7x LED, 2x button
UART header on PCB

Known issues:

- Broadband LED (missing GPIO - probably driven by the BCM6318)
- Internet LED (missing GPIO - probably driven by the BCM6318)
- WIFI LED (working only for one interface at a time, while in the
  OEM firmware works for both wifi interfaces; thus, this patch does
  not set a trigger by default)
- DSL not working (eth0)

UART connection
---------------
J1 HEADER (Qualcomm CPU)
. VCC
. GND
. RX
O TX

J41 HEADER (Broadcom CPU)
. VCC
. GND
. RX
O TX

The following instructions require a connection to the J1 UART header
and are tested for the Archer D7 v1.
For the Archer D7b v1, names should be changed accordingly.

Flash instructions under U-Boot, using UART
------------------------------------------
 1. Press "tpl" to stop autobooting and obtain U-Boot CLI access.
 2. Setup ip addresses for U-Boot and your tftp server.
 3. Issue below commands:
	tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d7-v1-squashfs-sysupgrade.bin
	erase 0x9f020000 +f90000
	cp.b 0x81000000 0x9f020000 0xf90000
	reset

Initramfs instructions under U-Boot for testing, using UART
----------------------------------------------------------
 1. Press "tpl" to stop autobooting and obtain U-Boot CLI access.
 2. Setup ip addresses for U-Boot and your tftp server.
 3. Issue below commands:
	tftpboot 0x81000000 openwrt-ath79-generic-tplink_archer-d7-v1-initramfs-kernel.bin
	bootm 0x81000000
 4. Here you can backup the original firmware and/or flash the sysupgrade openwrt if you want

Restore the original firmware
-----------------------------
 0. Backup every partition using the OpenWrt web interface
 1. Download the OEM firmware from the TP-Link website
 2. Extract the bin file in a folder (eg. Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin)
 3. Remove the U-Boot and the Broadcom image part from the file.
    Issue the following command:
	dd if="Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin" of="Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin.mod" skip=257 bs=512 count=31872
 4. Double check the .mod file size. It must be 16318464 bytes.
 5. Flash it using the OpenWrt web interface. Force the update if needed.
    WARNING: Remember to NOT keep settings.

 5b. (Alternative to 5.) Flash it using the U-Boot and UART connection.
     Issue below commands in the U-Boot:
	tftpboot 0x81000000 Archer_D7v1_1.6.0_0.9.1_up_boot(160216)_2016-02-16_15.55.48.bin.mod
	erase 0x9f020000 +f90000
	cp.b 0x81000000 0x9f020000 0xf90000
	reset

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
[cosmetic DTS changes, remove TPLINK_HWREVADD := 0, do not use two
phyXtpt at once, add missing buttons, minor commit message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-03-18 14:25:38 +01:00

194 lines
5.4 KiB
Bash
Raw Blame History

#!/bin/sh
[ -e /lib/firmware/$FIRMWARE ] && exit 0
. /lib/functions/caldata.sh
. /lib/functions/k2t.sh
board=$(board_name)
case "$FIRMWARE" in
"ath10k/cal-pci-0000:00:00.0.bin")
case $board in
comfast,cf-wr650ac-v1|\
comfast,cf-wr650ac-v2|\
devolo,magic-2-wifi|\
ubnt,unifiac-lite|\
ubnt,unifiac-lr|\
ubnt,unifiac-mesh|\
ubnt,unifiac-mesh-pro|\
ubnt,lap-120|\
ubnt,litebeam-ac-gen2|\
ubnt,nanobeam-ac|\
ubnt,nanostation-ac|\
ubnt,nanostation-ac-loco|\
ubnt,unifiac-pro|\
yuncore,a770)
caldata_extract "art" 0x5000 0x844
;;
devolo,dvl1200e|\
devolo,dvl1200i|\
devolo,dvl1750c|\
devolo,dvl1750e|\
devolo,dvl1750i|\
devolo,dvl1750x)
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) -1)
;;
dlink,dir-859-a1)
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(mtd_get_mac_ascii devdata "wlan5mac")
;;
elecom,wrc-1750ghbk2-i)
caldata_extract "art" 0x5000 0x844
;;
engenius,ecb1750)
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(mtd_get_mac_ascii u-boot-env athaddr)
;;
engenius,epg5000|\
iodata,wn-ac1167dgr|\
iodata,wn-ac1600dgr2|\
sitecom,wlr-7100)
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +1)
;;
engenius,ews511ap)
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +1)
;;
glinet,gl-ar750)
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) +1)
;;
glinet,gl-x750)
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) +2)
;;
nec,wg800hp)
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(mtd_get_mac_text board_data 0x880)
;;
ocedo,koala|\
ocedo,ursus)
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(mtd_get_mac_binary art 0xc)
;;
openmesh,om5p-ac-v2)
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16)
;;
qihoo,c301)
caldata_extract "radiocfg" 0x5000 0x844
ath10k_patch_mac $(mtd_get_mac_ascii devdata wlan5mac)
;;
tplink,archer-a7-v5|\
tplink,archer-c2-v3|\
tplink,archer-c7-v4|\
tplink,archer-c7-v5|\
tplink,archer-c25-v1)
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary info 0x8) -1)
;;
tplink,archer-c5-v1|\
tplink,archer-c7-v2)
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary u-boot 0x1fc00) -1)
;;
tplink,archer-d50-v1)
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary romfile 0xf100) +2)
;;
tplink,archer-d7-v1|\
tplink,archer-d7b-v1)
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary romfs 0xf100) +2)
;;
tplink,re350k-v1)
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary config 0x10008) +2)
;;
tplink,re355-v1|\
tplink,re450-v1)
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -2)
;;
tplink,re450-v2)
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary info 0x8) +1)
;;
tplink,tl-wr902ac-v1)
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary tplink 0x8) -1)
;;
esac
;;
"ath10k/cal-pci-0000:01:00.0.bin")
case $board in
sitecom,wlr-8100)
caldata_extract "art" 0x5000 0x844
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_ascii u-boot-env ethaddr) +1)
;;
esac
;;
"ath10k/pre-cal-pci-0000:00:00.0.bin")
case $board in
comfast,cf-e313ac)
caldata_extract "art" 0x5000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary art 0x6)
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
rm /lib/firmware/ath10k/QCA9888/hw2.0/board-2.bin
;;
comfast,cf-e560ac)
caldata_extract "art" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary art 0x0) +2)
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
rm /lib/firmware/ath10k/QCA9888/hw2.0/board-2.bin
;;
dlink,dir-842-c1|\
dlink,dir-842-c2|\
dlink,dir-842-c3|\
nec,wg1200cr)
caldata_extract "art" 0x5000 0x2f20
ath10k_patch_mac $(mtd_get_mac_ascii devdata wlan5mac)
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
netgear,ex6400|\
netgear,ex7300)
caldata_extract "caldata" 0x5000 0x2f20
ath10k_patch_mac $(mtd_get_mac_binary caldata 0xc)
;;
phicomm,k2t)
caldata_extract "art" 0x5000 0x2f20
ath10k_patch_mac $(k2t_get_mac "5g_mac")
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
tplink,archer-c58-v1|\
tplink,archer-c59-v1|\
tplink,archer-c59-v2|\
tplink,archer-c60-v1|\
tplink,archer-c60-v2|\
tplink,archer-c60-v3|\
tplink,archer-c6-v2|\
tplink,archer-c6-v2-us)
caldata_extract "art" 0x5000 0x2f20
ath10k_patch_mac $(macaddr_add $(mtd_get_mac_binary mac 0x8) -1)
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
yuncore,a782|\
yuncore,xd4200)
caldata_extract "art" 0x5000 0x2f20
ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
/lib/firmware/ath10k/QCA9888/hw2.0/board.bin
;;
esac
;;
*)
exit 1
;;
esac
Reference in a new issue View git blame Copy permalink