6ffe8a473e
The Seagate BlackArmor NAS220 is a consumer NAS
with two internal drive bays. The stock OS runs
RAID 1 over the disks via mdadm.
Device specification:
- SoC: Marvell 88F6192 800 MHz
- RAM: 128 MB
- Flash: 32 MB
- 2 x internal SATA II drives
- Ethernet: 10/100/1000 Mbps (single port, no switch)
- WLAN: None
- LED: Power, Status, Sata Activity
- Key: Power, Reset
- Serial: 10 pin header, (115200,8,N,1), 3.3V TTL
9|x - x|10
7|x - x|8
5|x - GND|6
3|x - RX|4
1|TX - x|2
front of case
- USB ports: 2 x USB 2.0
Flash instruction:
NOTE: this process uses a serial connection. It will upgrade the
bootloader and reset the bootloader environment variables
TFTP server setup
- Setup PC with TFTP server set the PC IP to 10.4.50.5 as TFTP server
- Copy these files to TFTP server location
- u-boot.kwb
- seagate_blackarmor-nas220-initramfs-uImage
- seagate_blackarmor-nas220-squashfs-sysupgrade.bin
- seagate_blackarmor-nas220-squashfs-factory.bin
Seagate NAS setup
- Connect LAN cable between PC and seagate device
- Connect to serial to seagate device
Install u-boot
- Boot seagate device and stop in bootloader by pressing any key
- run 'printenv' from u-boot and save the values
- tftpboot 0x2000000 u-boot.kwb
- nand erase.part uboot
- nand write 0x2000000 0x0 ${filesize}
- reset
Update MAC address in u-boot env
- Stop in u-boot by pressing any key
- Get your MAC address from your saved printenv. Is also on chassis
- setenv ethaddr <your MAC>
- saveenv
Option 1 (recommended) - Install OpenWrt via initramfs and sysupgrade
- tftpboot 0x2000000 seagate_blackarmor-nas220-initramfs-uImage
- bootm 0x2000000
- *OpenWrt should be running now, however it is not written to flash yet*
- From the running instance of OpenWrt use Luci's "flash image" feature
from the web site or use sysupgrade from the console to write
seagate_blackarmor-nas220-squashfs-sysupgrade.bin to flash
Option 2 - Install OpenWrt by flashing factory image from u-boot
- nand erase.part ubi
- tftpboot 0x2000000 seagate_blackarmor-nas220-squashfs-factory.bin
- nand write 0x2000000 ubi ${filesize}
- reset
Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
50 lines
1 KiB
Bash
Executable file
50 lines
1 KiB
Bash
Executable file
#!/bin/sh
|
|
#
|
|
# Copyright (C) 2012-2015 OpenWrt.org
|
|
#
|
|
|
|
. /lib/functions/uci-defaults.sh
|
|
. /lib/functions/system.sh
|
|
|
|
board_config_update
|
|
|
|
board=$(board_name)
|
|
|
|
case "$board" in
|
|
"checkpoint,l-50")
|
|
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5 lan6 lan7 lan8 dmz" "eth0"
|
|
;;
|
|
"cisco,on100")
|
|
ucidef_set_interface_lan "eth0 eth1"
|
|
;;
|
|
"cloudengines,pogoe02"|\
|
|
"cloudengines,pogoplugv4"|\
|
|
"iom,iconnect-1.1"|\
|
|
"iom,ix2-200"|\
|
|
"raidsonic,ib-nas62x0"|\
|
|
"seagate,blackarmor-nas220"|\
|
|
"seagate,dockstar"|\
|
|
"seagate,goflexhome"|\
|
|
"seagate,goflexnet"|\
|
|
"zyxel,nsa310s")
|
|
ucidef_set_interface_lan "eth0" "dhcp"
|
|
;;
|
|
"linksys,e4200-v2"|\
|
|
"linksys,ea3500"|\
|
|
"linksys,ea4500")
|
|
ucidef_set_interfaces_lan_wan "ethernet1 ethernet2 ethernet3 ethernet4" "internet"
|
|
ucidef_set_interface_macaddr "wan" $( mtd_get_mac_ascii u_env eth1addr )
|
|
;;
|
|
"zyxel,nsa310b"|\
|
|
"zyxel,nsa325")
|
|
ucidef_set_interface_lan "eth0" "dhcp"
|
|
ucidef_set_interface_macaddr "lan" $( mtd_get_mac_ascii uboot_env ethaddr )
|
|
;;
|
|
*)
|
|
ucidef_set_interface_lan "eth0"
|
|
;;
|
|
esac
|
|
|
|
board_config_flush
|
|
|
|
exit 0
|