67ce9aedd6
This patch adds support for the Check Point L-50 from 600/1100 series routers. Specification: -CPU: Marvell Kirkwood 88F6281 1200MHz -RAM: 512MB -Flash: NAND 512MB -WiFi: mPCIe card based on Atheros AR9287 b/g/n -WAN: 1 Gigabit Port (Marvell 88E1116R PHY) -LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+4)) -USB: 2x USB2.0 -Express card slot -SD card slot -Serial console: RJ-45 115200 8n1 -Unsupported DSL Known issues: -DSL not supported -Expresscard not tested Installation: Step one -> backup: make backup u-boot and env for revert stock posibility make backup dsl_mac_addr, dmz_mac_addr, eth1addr, ethaddr and all lanX_mac_addr Step two -> Use kwboot tool to upload openwrt u-boot to RAM: run kwboot: "kwboot -B 115200 /dev/ttyUSB0 -b u-boot.kwb -p -t" end start u-boot Step three -> Restore macs (e.g. below): setenv eth1addr 00:1C:XX:XX:XX:6C setenv ethaddr 00:1C:XX:XX:XX:6B setenv lan1_mac_addr 00:1C:XX:XX:XX:6C setenv lan2_mac_addr 00:1C:XX:XX:XX:6D setenv lan3_mac_addr 00:1C:XX:XX:XX:6E setenv lan4_mac_addr 00:1C:XX:XX:XX:6F setenv lan5_mac_addr 00:1C:XX:XX:XX:70 setenv lan6_mac_addr 00:1C:XX:XX:XX:71 setenv lan7_mac_addr 00:1C:XX:XX:XX:72 setenv lan8_mac_addr 00:1C:XX:XX:XX:73 setenv dmz_mac_addr 00:1C:XX:XX:XX:74 setenv dsl_mac_addr 00:1C:XX:XX:XX:75 Step four -> flash u-boot: mw 0x0800000 0xffff 0x100000 nand erase 0x0 100000 tftp 0x0800000 openwrt-kirkwood-l50-u-boot.kwb nand write 0x0800000 0x0 0x100000 saveenv Step five -> run initramfs image: tftpboot 0x02000000 openwrt.bin; bootm 0x02000000; Step six -> install sysupgrade OpenWrt image: copy to /tmp/ sysupgrade image run sysupgrade Back to stock: Restore original u-boot end env. Install factory image via stock u-boot. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
48 lines
1,003 B
Bash
Executable file
48 lines
1,003 B
Bash
Executable file
#!/bin/sh
|
|
#
|
|
# Copyright (C) 2012-2015 OpenWrt.org
|
|
#
|
|
|
|
. /lib/functions/uci-defaults.sh
|
|
. /lib/functions/system.sh
|
|
|
|
board_config_update
|
|
|
|
board=$(board_name)
|
|
|
|
case "$board" in
|
|
"checkpoint,l-50")
|
|
ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5 lan6 lan7 lan8 dmz" "eth0"
|
|
;;
|
|
"cisco,on100")
|
|
ucidef_set_interface_lan "eth0 eth1"
|
|
;;
|
|
"cloudengines,pogoe02"|\
|
|
"cloudengines,pogoplugv4"|\
|
|
"iom,iconnect-1.1"|\
|
|
"iom,ix2-200"|\
|
|
"raidsonic,ib-nas62x0"|\
|
|
"seagate,dockstar"|\
|
|
"seagate,goflexhome"|\
|
|
"seagate,goflexnet"|\
|
|
"zyxel,nsa310s")
|
|
ucidef_set_interface_lan "eth0" "dhcp"
|
|
;;
|
|
"linksys,audi"|\
|
|
"linksys,viper")
|
|
ucidef_set_interfaces_lan_wan "ethernet1 ethernet2 ethernet3 ethernet4" "internet"
|
|
ucidef_set_interface_macaddr "wan" $( mtd_get_mac_ascii u_env eth1addr )
|
|
;;
|
|
"zyxel,nsa310b"|\
|
|
"zyxel,nsa325")
|
|
ucidef_set_interface_lan "eth0" "dhcp"
|
|
ucidef_set_interface_macaddr "lan" $( mtd_get_mac_ascii uboot_env ethaddr )
|
|
;;
|
|
*)
|
|
ucidef_set_interface_lan "eth0"
|
|
;;
|
|
esac
|
|
|
|
board_config_flush
|
|
|
|
exit 0
|