Difuse/difos
2
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity Actions
difos/target/linux/ipq40xx/base-files/etc/board.d/02_network
Marek Lindner 4871fd2616 ipq40xx: add support for Plasma Cloud PA2200 
Device specifications:

* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
  - 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 36-64)
  - QCA9888 hw2.0 (PCI)
  - requires special BDF in QCA9888/hw2.0/board-2.bin
    bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 100-165)
  - QCA4019 hw1.0 (SoC)
  - requires special BDF in QCA4019/hw1.0/board-2.bin with
    bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200
* GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE
* GPIO-LEDs for power (orange) and status (blue)
* 1x GPIO-button (reset)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
  - phy@mdio3:
    + Label: Ethernet 1
    + gmac0 (ethaddr) in original firmware
    + used as LAN interface
  - phy@mdio4:
    + Label: Ethernet 2
    + gmac1 (eth1addr) in original firmware
    + 802.3at POE+
    + used as WAN interface
* 12V 2A DC

Flashing instructions:

The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.

Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
2020-12-22 19:11:50 +01:00

178 lines
4.1 KiB
Bash
Executable file
Raw Blame History

#!/bin/sh
#
# Copyright (c) 2015 The Linux Foundation. All rights reserved.
# Copyright (c) 2011-2015 OpenWrt.org
#
. /lib/functions/uci-defaults.sh
. /lib/functions/system.sh
ipq40xx_setup_interfaces()
{
local board="$1"
case "$board" in
8dev,habanero-dvk|\
8dev,jalapeno|\
alfa-network,ap120c-ac|\
engenius,emr3500|\
engenius,ens620ext|\
luma,wrtq-329acn|\
plasmacloud,pa1200|\
plasmacloud,pa2200)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
;;
aruba,ap-303|\
aruba,ap-365|\
avm,fritzrepeater-1200|\
dlink,dap-2610 |\
engenius,eap1300|\
engenius,emd1|\
meraki,mr33|\
netgear,ex6100v2|\
netgear,ex6150v2|\
zyxel,wre6606)
ucidef_set_interface_lan "eth0"
;;
aruba,ap-303h)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
"0u@eth0" "2:lan:1" "3:lan:2" "4:lan:3" "0u@eth1" "5:wan"
;;
asus,map-ac2200|\
cilab,meshpoint-one|\
edgecore,ecw5211|\
edgecore,oap100|\
openmesh,a42|\
openmesh,a62)
ucidef_set_interfaces_lan_wan "eth1" "eth0"
;;
asus,rt-ac58u|\
zyxel,nbg6617)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
"0u@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1"
;;
avm,fritzbox-4040|\
linksys,ea6350v3|\
linksys,ea8300|\
linksys,mr8300)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
;;
avm,fritzbox-7530)
ucidef_add_switch "switch0" \
"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan"
;;
avm,fritzrepeater-3000)
ucidef_add_switch "switch0" \
"0u@eth0" "4:lan:1" "5:lan:2"
;;
compex,wpj419|\
compex,wpj428|\
engenius,eap2200)
ucidef_set_interface_lan "eth0 eth1"
;;
buffalo,wtr-m2133hp)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
"0u@eth0" "2:lan:3" "3:lan:2" "4:lan:1"
;;
cellc,rtl30vw)
ucidef_set_interface_lan "eth0"
ucidef_add_switch "switch0" \
"0u@eth0" "3:lan" "4:lan"
;;
ezviz,cs-w3-wd1200g-eup)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
"0u@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "0u@eth1" "5:wan"
;;
glinet,gl-b1300 |\
glinet,gl-s1300)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
"0u@eth0" "3:lan" "4:lan"
;;
mobipromo,cm520-79f)
ucidef_add_switch "switch0" \
"0u@eth0" "3:lan:2" "4:lan:1"
ucidef_set_interface_wan "eth1"
;;
qxwlan,e2600ac-c1 |\
qxwlan,e2600ac-c2)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
"0u@eth0" "3:lan" "4:lan" "0u@eth1" "5:wan"
;;
unielec,u4019-32m)
ucidef_set_interfaces_lan_wan "eth0" "eth1"
ucidef_add_switch "switch0" \
"0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "0u@eth1" "5:wan"
;;
*)
echo "Unsupported hardware. Network interfaces not initialized"
;;
esac
}
ipq40xx_setup_macs()
{
local board="$1"
local lan_mac=""
local wan_mac=""
local label_mac=""
case "$board" in
8dev,habanero-dvk)
label_mac=$(mtd_get_mac_binary "ART" 0x1006)
;;
asus,rt-ac58u)
CI_UBIPART=UBI_DEV
wan_mac=$(mtd_get_mac_binary_ubi Factory 0x1006)
lan_mac=$(mtd_get_mac_binary_ubi Factory 0x5006)
label_mac=$wan_mac
;;
cilab,meshpoint-one)
label_mac=$(mtd_get_mac_binary "ART" 0x1006)
;;
dlink,dap-2610)
lan_mac=$(mtd_get_mac_ascii bdcfg lanmac)
label_mac=$lan_mac
;;
engenius,eap2200|\
engenius,emd1)
lan_mac=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
label_mac=$lan_mac
;;
engenius,emr3500)
wan_mac=$(mtd_get_mac_ascii 0:APPSBLENV wanaddr)
lan_mac=$(mtd_get_mac_ascii 0:APPSBLENV ethaddr)
label_mac=$wan_mac
;;
engenius,ens620ext)
wan_mac=$(mtd_get_mac_ascii u-boot-env ethaddr)
lan_mac=$(macaddr_add "$wan_mac" 1)
;;
ezviz,cs-w3-wd1200g-eup)
label_mac=$(mtd_get_mac_binary "ART" 0x6)
;;
linksys,ea6350v3)
wan_mac=$(mtd_get_mac_ascii devinfo hw_mac_addr)
lan_mac=$(macaddr_add "$wan_mac" 1)
;;
esac
[ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac
[ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac
[ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac
}
board_config_update
board=$(board_name)
ipq40xx_setup_interfaces $board
ipq40xx_setup_macs $board
board_config_flush
exit 0
Reference in a new issue View git blame Copy permalink