ad90a42e48
Like in the previous patches for ath79 and ramips, this will remove the "devicename" from LED labels in ipq40xx. The devicename is removed in DTS files and 01_leds, and a migration script is added. While at it, also harmonize capitalization of wlan2G/wlan5G vs. wlan2g/wlan5g. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
421 lines
7.3 KiB
Text
421 lines
7.3 KiB
Text
// SPDX-License-Identifier: GPL-2.0-only OR MIT
|
|
|
|
#include "qcom-ipq4019.dtsi"
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/input.h>
|
|
#include <dt-bindings/soc/qcom,tcsr.h>
|
|
|
|
/ {
|
|
model = "Aruba AP-303H";
|
|
compatible = "aruba,ap-303h";
|
|
|
|
aliases {
|
|
led-boot = &led_system_green;
|
|
led-failsafe = &led_system_red;
|
|
led-running = &led_system_green;
|
|
led-upgrade = &led_system_amber;
|
|
};
|
|
|
|
memory {
|
|
device_type = "memory";
|
|
reg = <0x80000000 0x10000000>;
|
|
};
|
|
|
|
soc {
|
|
rng@22000 {
|
|
status = "okay";
|
|
};
|
|
|
|
mdio@90000 {
|
|
status = "okay";
|
|
pinctrl-0 = <&mdio_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
reset-gpios = <&tlmm 19 GPIO_ACTIVE_LOW>;
|
|
reset-delay-us = <2000>;
|
|
};
|
|
|
|
counter@4a1000 {
|
|
compatible = "qcom,qca-gcnt";
|
|
reg = <0x4a1000 0x4>;
|
|
};
|
|
|
|
ess_tcsr@1953000 {
|
|
compatible = "qcom,tcsr";
|
|
reg = <0x1953000 0x1000>;
|
|
qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
|
|
};
|
|
|
|
tcsr@1949000 {
|
|
compatible = "qcom,tcsr";
|
|
reg = <0x1949000 0x100>;
|
|
qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
|
|
};
|
|
|
|
tcsr@194b000 {
|
|
compatible = "qcom,tcsr";
|
|
reg = <0x194b000 0x100>;
|
|
qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
|
|
};
|
|
|
|
tcsr@1957000 {
|
|
compatible = "qcom,tcsr";
|
|
reg = <0x1957000 0x100>;
|
|
qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
|
|
};
|
|
|
|
usb2@60f8800 {
|
|
status = "okay";
|
|
};
|
|
|
|
crypto@8e3a000 {
|
|
status = "okay";
|
|
};
|
|
|
|
watchdog@b017000 {
|
|
status = "okay";
|
|
};
|
|
|
|
ess-switch@c000000 {
|
|
status = "okay";
|
|
};
|
|
|
|
edma@c080000 {
|
|
status = "okay";
|
|
};
|
|
|
|
i2c_0: i2c@78b7000 {
|
|
pinctrl-0 = <&i2c_0_pins>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
|
|
tpm@29 {
|
|
/* No Driver */
|
|
compatible = "atmel,at97sc3203";
|
|
reg = <0x29>;
|
|
read-only;
|
|
};
|
|
|
|
power-monitor@40 {
|
|
/* No driver */
|
|
compatible = "isl,isl28022";
|
|
reg = <0x40>;
|
|
};
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
wifi_green {
|
|
label = "green:wifi";
|
|
gpios = <&tlmm 27 GPIO_ACTIVE_HIGH>;
|
|
linux,default-trigger = "phy0tpt";
|
|
};
|
|
|
|
wifi_amber {
|
|
label = "amber:wifi";
|
|
gpios = <&tlmm 28 GPIO_ACTIVE_HIGH>;
|
|
linux,default-trigger = "phy1tpt";
|
|
};
|
|
|
|
pse {
|
|
label = "green:pse";
|
|
gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led_system_red: system_red {
|
|
label = "red:system";
|
|
gpios = <&tlmm 25 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led_system_green: system_green {
|
|
label = "green:system";
|
|
gpios = <&tlmm 24 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led_system_amber: system_amber {
|
|
label = "amber:system";
|
|
gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
|
|
keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "Reset button";
|
|
gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_RESTART>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&blsp_dma {
|
|
status = "okay";
|
|
};
|
|
|
|
&blsp1_uart1 {
|
|
pinctrl-0 = <&serial_0_pins>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&blsp1_uart2 {
|
|
/* Texas Instruments CC2540T BLE radio */
|
|
pinctrl-0 = <&serial_1_pins>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&cryptobam {
|
|
status = "okay";
|
|
};
|
|
|
|
&qpic_bam {
|
|
status = "okay";
|
|
};
|
|
|
|
&tlmm {
|
|
/*
|
|
* In addition to the Pins listed below,
|
|
* the following GPIOs have "features":
|
|
* 39 - out - active low to force HW reset
|
|
* 32 - out - active low to reset TPM
|
|
* 43 - out - active low to reset BLE radio
|
|
* 41 - out - pulse to set warm reset status
|
|
* 34 - out - active low to enable PSE port
|
|
* 22 - in - active low when 802.3at powered
|
|
* 29 - in - active high when DC powered
|
|
* 40 - in - active low when reset due to cold HW reset
|
|
* 30 - in - active low when USB overcurrent detected
|
|
* 35 - in - interrupt line for power monitor chip
|
|
* 31 - in - active low when PSE port active
|
|
*/
|
|
mdio_pins: mdio_pinmux {
|
|
mux_1 {
|
|
pins = "gpio6";
|
|
function = "mdio";
|
|
bias-pull-up;
|
|
};
|
|
mux_2 {
|
|
pins = "gpio7";
|
|
function = "mdc";
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
|
|
spi_0_pins: spi_0_pinmux {
|
|
pin {
|
|
function = "blsp_spi0";
|
|
pins = "gpio13", "gpio14", "gpio15";
|
|
drive-strength = <12>;
|
|
bias-disable;
|
|
};
|
|
pin_cs {
|
|
function = "gpio";
|
|
pins = "gpio12", "gpio59";
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
output-high;
|
|
};
|
|
};
|
|
|
|
i2c_0_pins: i2c_0_pinmux {
|
|
mux {
|
|
pins = "gpio20", "gpio21";
|
|
function = "blsp_i2c0";
|
|
drive-strength = <4>;
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
serial_0_pins: serial_0_pinmux {
|
|
mux {
|
|
pins = "gpio16", "gpio17";
|
|
function = "blsp_uart0";
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
serial_1_pins: serial_1_pinmux {
|
|
mux {
|
|
pins = "gpio8", "gpio9";
|
|
function = "blsp_uart1";
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
usb-power {
|
|
line-name = "USB-power";
|
|
gpios = <23 GPIO_ACTIVE_HIGH>;
|
|
gpio-hog;
|
|
output-high;
|
|
};
|
|
};
|
|
|
|
&blsp1_spi1 {
|
|
pinctrl-0 = <&spi_0_pins>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>, <&tlmm 59 GPIO_ACTIVE_HIGH>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <24000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
/*
|
|
* There is no partition map for the NOR flash
|
|
* in the stock firmware.
|
|
*
|
|
* All partitions here are based on offsets
|
|
* found in the U-Boot GPL code and information
|
|
* from smem.
|
|
*/
|
|
|
|
partition@0 {
|
|
label = "sbl1";
|
|
reg = <0x0 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "mibib";
|
|
reg = <0x40000 0x20000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@60000 {
|
|
label = "qsee";
|
|
reg = <0x60000 0x60000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@c0000 {
|
|
label = "cdt";
|
|
reg = <0xc0000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@d0000 {
|
|
label = "ddrparams";
|
|
reg = <0xd0000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@e0000 {
|
|
label = "appsblenv";
|
|
reg = <0xe0000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@f0000 {
|
|
label = "appsbl";
|
|
reg = <0xf0000 0x100000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@1e0000 {
|
|
label = "ART";
|
|
reg = <0x1f0000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@1f0000 {
|
|
label = "osss";
|
|
reg = <0x200000 0x170000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@200000 {
|
|
label = "pds";
|
|
reg = <0x370000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@380000 {
|
|
label = "apcd";
|
|
reg = <0x380000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@390000 {
|
|
label = "mfginfo";
|
|
reg = <0x390000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@3a0000 {
|
|
label = "fcache";
|
|
reg = <0x3a0000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@3b0000 {
|
|
/* Called osss1 in smem */
|
|
label = "u-boot-env-bak";
|
|
reg = <0x3b0000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@3f0000 {
|
|
label = "u-boot-env";
|
|
reg = <0x3c0000 0x40000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
|
|
flash@1 {
|
|
status = "okay";
|
|
|
|
compatible = "spi-nand";
|
|
reg = <1>;
|
|
spi-max-frequency = <24000000>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
/* 'aos0' in Aruba firmware */
|
|
label = "aos0";
|
|
reg = <0x0 0x2000000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@2000000 {
|
|
/* 'aos1' in Aruba firmware */
|
|
label = "ubi";
|
|
reg = <0x2000000 0x2000000>;
|
|
};
|
|
|
|
partition@4000000 {
|
|
label = "aruba-ubifs";
|
|
reg = <0x4000000 0x4000000>;
|
|
read-only;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&usb2_hs_phy {
|
|
status = "okay";
|
|
};
|
|
|
|
&wifi0 {
|
|
status = "okay";
|
|
qcom,ath10k-calibration-variant = "Aruba-AP-303";
|
|
};
|
|
|
|
&wifi1 {
|
|
status = "okay";
|
|
qcom,ath10k-calibration-variant = "Aruba-AP-303";
|
|
};
|