2090b8af0a
Hardware:
SOC: Qualcomm IPQ4018
RAM: 128 MB Nanya NT5CC64M16GP-DI
FLASH: 16 MB Macronix MX25L12805D
ETH: Qualcomm QCA8075 (4 Gigabit ports, 3xLAN, 1xWAN)
WLAN: Qualcomm IPQ4018 (2.4 & 5 Ghz)
BUTTON: Shared WPS/Reset button
LED: RGB Status/Power LED
SERIAL: Header J8 (UART, Left side of board). Numbered from
top to bottom:
(1) GND, (2) TX, (3) RX, (4) VCC (White triangle
next to it).
3.3v, 115200, 8N1
Tested/Working:
* Ethernet
* WiFi (2.4 and 5GHz)
* Status LED
* Reset Button (See note below)
Implementation notes:
* The shared WPS/Reset button is implemented as a Reset button
* I could not find a original firmware image to reverse engineer, meaning
currently it's not possible to flash OpenWrt through the Web GUI.
Installation (Through Serial console & TFTP):
1. Set your PC to fixed IP 192.168.1.12, Netmask 255.255.255.0, and connect to
one of the LAN ports
2. Rename the initramfs image to 'C0A8010B.img' and enable a TFTP server on
your pc, to serve the image
2. Connect to the router through serial (See connection properties above)
3. Hit a key during startup, to pause startup
4. type `setenv serverip 192.168.1.12`, to set the tftp server address
5. type `tftpboot`, to load the image from the laptop through tftp
6. type `bootm` to run the loaded image from memory
6. (If you want to return to stock firmware later, create an full MTD backup,
e.g. using instructions here https://openwrt.org/docs/guide-user/installation/generic.backup#create_full_mtd_backup)
7. Transfer the 'sysupgrade' OpenWrt firmware image from PC to router, e.g.:
`scp xxx-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/upgrade.bin`
8. Run sysupgrade to permanently install OpenWrt to flash: `sysupgrade -n /tmp/upgrade.bin`
Revert to stock:
To revert to stock, you need the MTD backup from step 6 above:
1. Unpack the MTD backup archive
2. Transfer the 'firmware' partition image to the router (e.g. mtd8_firmware.backup)
3. On the router, do `mtd write mtd8_firmware.backup firmware`
Signed-off-by: Tom Brouwer <tombrouwer@outlook.com>
[removed BOARD_NAME, OpenWRT->OpenWrt, changed LED device name to board name]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
52 lines
1.6 KiB
Diff
52 lines
1.6 KiB
Diff
From a10fab12a927e60b7141a602e740d70cb4d09e4a Mon Sep 17 00:00:00 2001
|
|
From: John Crispin <john@phrozen.org>
|
|
Date: Thu, 9 Mar 2017 11:03:18 +0100
|
|
Subject: [PATCH] arm: boot: add dts files
|
|
|
|
Signed-off-by: John Crispin <john@phrozen.org>
|
|
---
|
|
arch/arm/boot/dts/Makefile | 23 +++++++++++++++++++++++
|
|
1 file changed, 23 insertions(+)
|
|
|
|
--- a/arch/arm/boot/dts/Makefile
|
|
+++ b/arch/arm/boot/dts/Makefile
|
|
@@ -785,11 +785,39 @@ dtb-$(CONFIG_ARCH_QCOM) += \
|
|
qcom-apq8074-dragonboard.dtb \
|
|
qcom-apq8084-ifc6540.dtb \
|
|
qcom-apq8084-mtp.dtb \
|
|
+ qcom-ipq4018-a42.dtb \
|
|
+ qcom-ipq4018-ap120c-ac.dtb \
|
|
+ qcom-ipq4018-cs-w3-wd1200g-eup.dtb \
|
|
+ qcom-ipq4018-ea6350v3.dtb \
|
|
+ qcom-ipq4018-eap1300.dtb \
|
|
+ qcom-ipq4018-ens620ext.dtb \
|
|
+ qcom-ipq4018-ex6100v2.dtb \
|
|
+ qcom-ipq4018-ex6150v2.dtb \
|
|
+ qcom-ipq4018-fritzbox-4040.dtb \
|
|
+ qcom-ipq4018-jalapeno.dtb \
|
|
+ qcom-ipq4018-meshpoint-one.dtb \
|
|
+ qcom-ipq4018-nbg6617.dtb \
|
|
+ qcom-ipq4018-rt-ac58u.dtb \
|
|
+ qcom-ipq4018-wre6606.dtb \
|
|
qcom-ipq4019-ap.dk01.1-c1.dtb \
|
|
qcom-ipq4019-ap.dk04.1-c1.dtb \
|
|
qcom-ipq4019-ap.dk04.1-c3.dtb \
|
|
qcom-ipq4019-ap.dk07.1-c1.dtb \
|
|
qcom-ipq4019-ap.dk07.1-c2.dtb \
|
|
+ qcom-ipq4019-a62.dtb \
|
|
+ qcom-ipq4019-fritzbox-7530.dtb \
|
|
+ qcom-ipq4019-fritzrepeater-1200.dtb \
|
|
+ qcom-ipq4019-fritzrepeater-3000.dtb \
|
|
+ qcom-ipq4019-ea8300.dtb \
|
|
+ qcom-ipq4019-map-ac2200.dtb \
|
|
+ qcom-ipq4019-e2600ac-c1.dtb \
|
|
+ qcom-ipq4019-e2600ac-c2.dtb \
|
|
+ qcom-ipq4019-u4019-32m.dtb \
|
|
+ qcom-ipq4019-wpj419.dtb \
|
|
+ qcom-ipq4028-wpj428.dtb \
|
|
+ qcom-ipq4029-ap-303.dtb \
|
|
+ qcom-ipq4029-gl-b1300.dtb \
|
|
+ qcom-ipq4029-mr33.dtb \
|
|
qcom-ipq8064-ap148.dtb \
|
|
qcom-msm8660-surf.dtb \
|
|
qcom-msm8960-cdp.dtb \
|