97af506edf
Check Point V-80 (Quantum Spark 1590 Appliance) is an Appliance, based
on Armada 8040 (88F8040).
Specification:
- SoC : Marvell Armada 8040 (88F8040)
- RAM : DDR4 2 GiB (4x 512 MiB chip)
- Flash : eMMC 4 GiB
- Ethernet : 10x 10/100/1000 Mbps
- LAN 1-8 : Marvell 88E6393X
- WAN : Marvell 88E1512
- DMZ : Marvell 88E1512 (RJ-45/SFP combo)
- LEDs/Keys (GPIO): 11x/1x
- UART : "CONSOLE" port (USB 1.1 Type-C)
- chip : Silicon Labs CP2102N
- port : ttyS0
- settings : 115200bps 8n1
- HW Monitoring : 2x nuvoTon NCT7802Y
- USB : USB 3.0 Type-A
- Power : 12 VDC, 3.3 A
- plug : DC Plug 2.5/5.5 mm (inner/outer)
Flash instruction (common):
1. Boot V-81 normally
2. Login to the vendor CLI (default: admin/admin) and login to the Linux
CLI by `expert` command
3. Update U-Boot environment variables by the following commands
fw_setenv bootcmd_ow_usb 'usb start; load usb 0:1 ${loadaddr} boot.scr && source ${loadaddr}'
fw_setenv bootcmd_ow_sd 'load mmc 0:1 ${loadaddr} boot.scr && source ${loadaddr}'
fw_setenv bootcmd_ow_emmc 'run set_mmc_internal; mmc read ${loadaddr} ${prim_header_mmc_blk} 4 && source ${loadaddr}'
fw_setenv bootcmd 'run bootcmd_ow_usb; run bootcmd_ow_sd; run bootcmd_ow_emmc; run bootcmd_part${activePartition};'
Attention: don't forget single quatations of values to prevent
expansion of variables
4. Turn off the device
Flash instruction (USB-boot/SD-boot):
1. Extract and burn (squashfs|ext4)-sdcard.img.gz to USB storage or
MicroSD card
2. Connect that storage to V-81
3. Turn on V-81 and it will be booted with OpenWrt in that USB storage
Flash instruction (eMMC-boot):
1. Copy initramfs image, dtb and bootsctipt to the USB storage with
renaming
initramfs.bin -------> Image
dtb -----------------> armada-8040-v-81.dtb
bootscript (.scr) ---> boot.scr
2. Connect that storage to the USB 3.0 port on V-81
3. Turn on V-81 and it will be booted with OpenWrt initramfs image in
that USB storage
4. Upload (squashfs|ext4)-sysupgrade.gz to V-81
5. Perform sysupgrade with the uploaded image
6. Wait ~100 seconds to complete flashing
Reverting to stock firmware:
1. Turn on V-81 and interrupt booting by Ctrl + C
2. Select "4. Restore to Factory Defaults (local)"
3. Wait ~180 seconds to complete restoring and rebooting
Notes:
- The partition table in the internal eMMC has single partition, but
"blkdevparts=" parameter will be passed from the bootloader and that
definition will be used instead.
- The port-side LED pairs of RJ-45/SFP ports on V-81 are switched by a
GPIO pin of pin7 on &cp0_gpio2. (High(1): RJ-45, Low(0): SFP)
This needs to be switched manually.
- The MicroSD card slot is too unstable and the following messages are
printed without "marvell,xenon-phy-slow-mode;" property.
[ 97.060851] mmc0: error -84 whilst initialising SD card
[ 97.137049] mmc0: error -84 whilst initialising SD card
[ 97.214315] mmc0: error -84 whilst initialising SD card
...
- There are no detailed information about maximum power consumption
limit of the SFP port or optional DSL-SFP modules sold officially.
But the power requirement of almost DSL-SFP modules are 3.3V/700mA, so
set the maximum value of the SFP port to 2000 mW (Power Level III).
- Do not insert a MicroSD card before turning of the device when OpenWrt
installation. The stock firmware deletes all files in the first
partition automatically, to use it as a storage for logs.
MAC addresses:
LAN: 00:1C:7F:xx:xx:FA (mmcblk1boot0, ethaddr (text))
WAN: 00:1C:7F:xx:xx:F9 (mmcblk1boot0, eth2addr (text))
DMZ: 00:1C:7F:xx:xx:FB (mmcblk1boot0, eth1addr (text))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16904
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
159 lines
4.8 KiB
Makefile
159 lines
4.8 KiB
Makefile
define Build/append-bootscript
|
|
cat $@-boot.scr >> $@
|
|
endef
|
|
|
|
define Device/FitImage
|
|
KERNEL_SUFFIX := -uImage.itb
|
|
KERNEL = kernel-bin | gzip | fit gzip $$(KDIR)/image-$$(DEVICE_DTS).dtb
|
|
KERNEL_NAME := Image
|
|
endef
|
|
|
|
define Device/UbiFit
|
|
KERNEL_IN_UBI := 1
|
|
IMAGES := factory.ubi sysupgrade.bin
|
|
IMAGE/factory.ubi := append-ubi
|
|
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
|
endef
|
|
|
|
define Device/checkpoint_v-80
|
|
$(call Device/Default-arm64)
|
|
DEVICE_VENDOR := Check Point
|
|
DEVICE_MODEL := V-80
|
|
SOC := armada-7040
|
|
BOOT_SCRIPT := v-80
|
|
IMAGES += sysupgrade.gz
|
|
IMAGE/sysupgrade.gz := boot-scr eMMC | append-bootscript | pad-to 2048 | \
|
|
append-kernel | \
|
|
sysupgrade-tar kernel=$$$$@ dtb=$$(KDIR)/image-$$(DEVICE_DTS).dtb | \
|
|
gzip | append-metadata
|
|
ARTIFACTS := initramfs.dtb initramfs.scr
|
|
ARTIFACT/initramfs.dtb := append-dtb
|
|
ARTIFACT/initramfs.scr := boot-scr INIT | append-bootscript
|
|
DEVICE_PACKAGES := kmod-dsa-mv88e6xxx kmod-hwmon-nct7802 kmod-rtc-ds1307
|
|
endef
|
|
TARGET_DEVICES += checkpoint_v-80
|
|
|
|
define Device/checkpoint_v-81
|
|
$(call Device/Default-arm64)
|
|
DEVICE_VENDOR := Check Point
|
|
DEVICE_MODEL := V-81
|
|
SOC := armada-8040
|
|
BOOT_SCRIPT := v-80
|
|
IMAGES += sysupgrade.gz
|
|
IMAGE/sysupgrade.gz := boot-scr eMMC | append-bootscript | pad-to 2048 | \
|
|
append-kernel | \
|
|
sysupgrade-tar kernel=$$$$@ dtb=$$(KDIR)/image-$$(DEVICE_DTS).dtb | \
|
|
gzip | append-metadata
|
|
ARTIFACTS := initramfs.dtb initramfs.scr
|
|
ARTIFACT/initramfs.dtb := append-dtb
|
|
ARTIFACT/initramfs.scr := boot-scr INIT | append-bootscript
|
|
DEVICE_PACKAGES := kmod-dsa-mv88e6xxx kmod-hwmon-nct7802 kmod-rtc-ds1307
|
|
endef
|
|
TARGET_DEVICES += checkpoint_v-81
|
|
|
|
define Device/globalscale_mochabin
|
|
$(call Device/Default-arm64)
|
|
DEVICE_VENDOR := Globalscale
|
|
DEVICE_MODEL := MOCHAbin
|
|
DEVICE_PACKAGES += kmod-dsa-mv88e6xxx
|
|
SOC := armada-7040
|
|
endef
|
|
TARGET_DEVICES += globalscale_mochabin
|
|
|
|
define Device/marvell_armada7040-db
|
|
$(call Device/Default-arm64)
|
|
DEVICE_VENDOR := Marvell
|
|
DEVICE_MODEL := Armada 7040 Development Board
|
|
DEVICE_DTS := armada-7040-db
|
|
IMAGE/sdcard.img.gz := boot-img-ext4 | sdcard-img-ext4 | gzip | append-metadata
|
|
endef
|
|
TARGET_DEVICES += marvell_armada7040-db
|
|
|
|
define Device/marvell_armada8040-db
|
|
$(call Device/Default-arm64)
|
|
DEVICE_VENDOR := Marvell
|
|
DEVICE_MODEL := Armada 8040 Development Board
|
|
DEVICE_DTS := armada-8040-db
|
|
IMAGE/sdcard.img.gz := boot-img-ext4 | sdcard-img-ext4 | gzip | append-metadata
|
|
endef
|
|
TARGET_DEVICES += marvell_armada8040-db
|
|
|
|
define Device/marvell_macchiatobin-doubleshot
|
|
$(call Device/Default-arm64)
|
|
DEVICE_VENDOR := SolidRun
|
|
DEVICE_MODEL := MACCHIATObin
|
|
DEVICE_VARIANT := Double Shot
|
|
DEVICE_ALT0_VENDOR := SolidRun
|
|
DEVICE_ALT0_MODEL := Armada 8040 Community Board
|
|
DEVICE_ALT0_VARIANT := Double Shot
|
|
DEVICE_PACKAGES += kmod-i2c-mux-pca954x
|
|
DEVICE_DTS := armada-8040-mcbin
|
|
SUPPORTED_DEVICES := marvell,armada8040-mcbin-doubleshot marvell,armada8040-mcbin
|
|
endef
|
|
TARGET_DEVICES += marvell_macchiatobin-doubleshot
|
|
|
|
define Device/marvell_macchiatobin-singleshot
|
|
$(call Device/Default-arm64)
|
|
DEVICE_VENDOR := SolidRun
|
|
DEVICE_MODEL := MACCHIATObin
|
|
DEVICE_VARIANT := Single Shot
|
|
DEVICE_ALT0_VENDOR := SolidRun
|
|
DEVICE_ALT0_MODEL := Armada 8040 Community Board
|
|
DEVICE_ALT0_VARIANT := Single Shot
|
|
DEVICE_PACKAGES += kmod-i2c-mux-pca954x
|
|
DEVICE_DTS := armada-8040-mcbin-singleshot
|
|
SUPPORTED_DEVICES := marvell,armada8040-mcbin-singleshot
|
|
endef
|
|
TARGET_DEVICES += marvell_macchiatobin-singleshot
|
|
|
|
define Device/mikrotik_rb5009
|
|
$(call Device/Default-arm64)
|
|
$(Device/NAND-128K)
|
|
$(call Device/FitImage)
|
|
$(call Device/UbiFit)
|
|
DEVICE_VENDOR := MikroTik
|
|
DEVICE_MODEL := RB5009
|
|
SOC := armada-7040
|
|
KERNEL_LOADADDR := 0x22000000
|
|
DEVICE_PACKAGES += kmod-i2c-gpio yafut kmod-dsa-mv88e6xxx
|
|
endef
|
|
TARGET_DEVICES += mikrotik_rb5009
|
|
|
|
define Device/marvell_clearfog-gt-8k
|
|
$(call Device/Default-arm64)
|
|
DEVICE_VENDOR := SolidRun
|
|
DEVICE_MODEL := Clearfog
|
|
DEVICE_VARIANT := GT-8K
|
|
DEVICE_PACKAGES += kmod-i2c-mux-pca954x kmod-crypto-hw-safexcel
|
|
DEVICE_DTS := armada-8040-clearfog-gt-8k
|
|
SUPPORTED_DEVICES := marvell,armada8040-clearfog-gt-8k
|
|
endef
|
|
TARGET_DEVICES += marvell_clearfog-gt-8k
|
|
|
|
define Device/iei_puzzle-m901
|
|
$(call Device/Default-arm64)
|
|
SOC := cn9131
|
|
DEVICE_VENDOR := iEi
|
|
DEVICE_MODEL := Puzzle-M901
|
|
DEVICE_PACKAGES += kmod-rtc-ds1307
|
|
endef
|
|
TARGET_DEVICES += iei_puzzle-m901
|
|
|
|
define Device/iei_puzzle-m902
|
|
$(call Device/Default-arm64)
|
|
SOC := cn9132
|
|
DEVICE_VENDOR := iEi
|
|
DEVICE_MODEL := Puzzle-M902
|
|
DEVICE_PACKAGES += kmod-rtc-ds1307
|
|
endef
|
|
TARGET_DEVICES += iei_puzzle-m902
|
|
|
|
define Device/solidrun_clearfog-pro
|
|
$(call Device/Default-arm64)
|
|
SOC := cn9130
|
|
DEVICE_VENDOR := SolidRun
|
|
DEVICE_MODEL := ClearFog Pro
|
|
DEVICE_PACKAGES += kmod-i2c-mux-pca954x kmod-dsa-mv88e6xxx
|
|
BOOT_SCRIPT := clearfog-pro
|
|
endef
|
|
TARGET_DEVICES += solidrun_clearfog-pro
|