a387c62114
Upstream uses a different filename, so lets rename our downstream mt7981.dtsi to mt7981b.dtsi and update the device tree of all MT7981 boards accordingly. This is to prepare for the switch to Linux 6.12 which is going to use the upstream mt7981b.dtsi (plus some patches on top). Signed-off-by: Daniel Golle <daniel@makrotopia.org>
188 lines
3 KiB
Text
188 lines
3 KiB
Text
// SPDX-License-Identifier: (GPL-2.0 OR MIT)
|
|
|
|
/dts-v1/;
|
|
|
|
#include "mt7981b.dtsi"
|
|
|
|
/ {
|
|
model = "WAVLINK WL-WN573HX3";
|
|
compatible = "wavlink,wl-wn573hx3", "mediatek,mt7981";
|
|
|
|
aliases {
|
|
label-mac-device = &wifi;
|
|
|
|
led-boot = &led_status_blue;
|
|
led-failsafe = &led_status_blue;
|
|
led-running = &led_status_blue;
|
|
led-upgrade = &led_status_blue;
|
|
|
|
serial0 = &uart0;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
gpio-keys {
|
|
compatible = "gpio-keys";
|
|
|
|
button-reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&pio 0 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led-0 {
|
|
color = <LED_COLOR_ID_GREEN>;
|
|
function = LED_FUNCTION_LAN;
|
|
gpios = <&pio 9 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led_status_blue: led-1 {
|
|
color = <LED_COLOR_ID_BLUE>;
|
|
function = LED_FUNCTION_STATUS;
|
|
gpios = <&pio 13 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&watchdog {
|
|
status = "okay";
|
|
};
|
|
|
|
ð {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mdio_pins>;
|
|
|
|
status = "okay";
|
|
|
|
gmac1: mac@1 {
|
|
compatible = "mediatek,eth-mac";
|
|
reg = <1>;
|
|
phy-mode = "gmii";
|
|
phy-handle = <&int_gbe_phy>;
|
|
nvmem-cells = <&macaddr_hw_44e 0>;
|
|
nvmem-cell-names = "mac-address";
|
|
};
|
|
};
|
|
|
|
&spi0 {
|
|
status = "disabled";
|
|
};
|
|
|
|
&spi2 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&spi2_flash_pins>;
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
|
|
spi-max-frequency = <52000000>;
|
|
spi-tx-bus-width = <4>;
|
|
spi-rx-bus-width = <4>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "bl2";
|
|
reg = <0x00000 0x40000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@40000 {
|
|
label = "u-boot-env";
|
|
reg = <0x40000 0x10000>;
|
|
read-only;
|
|
};
|
|
|
|
factory: partition@50000 {
|
|
label = "factory";
|
|
reg = <0x50000 0xb0000>;
|
|
read-only;
|
|
|
|
nvmem-layout {
|
|
compatible = "fixed-layout";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
eeprom_factory_0: eeprom@0 {
|
|
reg = <0x0 0x1000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
partition@100000 {
|
|
label = "fip";
|
|
reg = <0x100000 0x80000>;
|
|
read-only;
|
|
};
|
|
|
|
partition@f0000 {
|
|
compatible = "denx,fit";
|
|
label = "firmware";
|
|
reg = <0x180000 0xe00000>;
|
|
};
|
|
|
|
partition@f80000 {
|
|
label = "hw";
|
|
reg = <0xf80000 0x80000>;
|
|
|
|
nvmem-layout {
|
|
compatible = "fixed-layout";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
macaddr_hw_44e: macaddr@44e {
|
|
compatible = "mac-base";
|
|
reg = <0x44e 0x11>;
|
|
#nvmem-cell-cells = <1>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&pio {
|
|
spi2_flash_pins: spi2-pins {
|
|
mux {
|
|
function = "spi";
|
|
groups = "spi2", "spi2_wp_hold";
|
|
};
|
|
|
|
conf-pu {
|
|
pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
|
|
drive-strength = <8>;
|
|
bias-pull-up = <103>;
|
|
};
|
|
|
|
conf-pd {
|
|
pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
|
|
drive-strength = <8>;
|
|
bias-pull-down = <103>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&wifi {
|
|
status = "okay";
|
|
|
|
nvmem-cells = <&eeprom_factory_0>;
|
|
nvmem-cell-names = "eeprom";
|
|
};
|