Upstream uses a different filename, so lets rename our downstream mt7981.dtsi to mt7981b.dtsi and update the device tree of all MT7981 boards accordingly. This is to prepare for the switch to Linux 6.12 which is going to use the upstream mt7981b.dtsi (plus some patches on top). Signed-off-by: Daniel Golle <daniel@makrotopia.org>
170 lines
2.8 KiB
Text
170 lines
2.8 KiB
Text
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
|
|
|
/dts-v1/;
|
|
#include "mt7981b.dtsi"
|
|
|
|
/ {
|
|
model = "Ubiquiti UniFi 6 Plus";
|
|
compatible = "ubnt,unifi-6-plus", "mediatek,mt7981";
|
|
|
|
aliases {
|
|
serial0 = &uart0;
|
|
led-boot = &led_white;
|
|
led-failsafe = &led_white;
|
|
led-running = &led_blue;
|
|
led-upgrade = &led_blue;
|
|
label-mac-device = &gmac1;
|
|
};
|
|
|
|
chosen {
|
|
bootargs-override = "console=ttyS0,115200n8 rootwait root=/dev/mmcblk0p7";
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
|
|
gpio-keys {
|
|
compatible = "gpio-keys";
|
|
|
|
reset {
|
|
label = "reset";
|
|
linux,code = <KEY_RESTART>;
|
|
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
|
|
led_blue: dome-blue {
|
|
label = "blue:dome";
|
|
gpios = <&pio 9 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
led_white: dome-white {
|
|
label = "white:dome";
|
|
gpios = <&pio 34 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&uart0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&watchdog {
|
|
status = "okay";
|
|
};
|
|
|
|
&pio {
|
|
spi2_flash_pins: spi2-pins {
|
|
mux {
|
|
function = "spi";
|
|
groups = "spi2", "spi2_wp_hold";
|
|
};
|
|
|
|
conf-pu {
|
|
pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP";
|
|
drive-strength = <8>;
|
|
bias-pull-up = <103>;
|
|
};
|
|
|
|
conf-pd {
|
|
pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
|
|
drive-strength = <8>;
|
|
bias-pull-down = <103>;
|
|
};
|
|
};
|
|
|
|
mmc0_pins_default: mmc0-pins-default {
|
|
mux {
|
|
function = "flash";
|
|
groups = "emmc_45";
|
|
};
|
|
};
|
|
|
|
mmc0_pins_uhs: mmc0-pins-uhs {
|
|
mux {
|
|
function = "flash";
|
|
groups = "emmc_45";
|
|
};
|
|
};
|
|
};
|
|
|
|
&spi2 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&spi2_flash_pins>;
|
|
status = "okay";
|
|
|
|
flash@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
|
|
spi-max-frequency = <52000000>;
|
|
spi-tx-bus-width = <4>;
|
|
spi-rx-bus-width = <4>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
eeprom: partition@0 {
|
|
label = "EEPROM";
|
|
reg = <0x00000 0x10000>;
|
|
read-only;
|
|
|
|
nvmem-layout {
|
|
compatible = "fixed-layout";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
macaddr_eeprom_0: macaddr@0 {
|
|
reg = <0x0 0x6>;
|
|
};
|
|
|
|
macaddr_eeprom_6: macaddr@6 {
|
|
reg = <0x6 0x6>;
|
|
};
|
|
};
|
|
};
|
|
|
|
partition@10000 {
|
|
label = "u-boot-env";
|
|
reg = <0x10000 0x80000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&mmc0 {
|
|
pinctrl-names = "default", "state_uhs";
|
|
pinctrl-0 = <&mmc0_pins_default>;
|
|
pinctrl-1 = <&mmc0_pins_uhs>;
|
|
bus-width = <8>;
|
|
max-frequency = <52000000>;
|
|
cap-mmc-highspeed;
|
|
vmmc-supply = <®_3p3v>;
|
|
non-removable;
|
|
status = "okay";
|
|
};
|
|
|
|
ð {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mdio_pins>;
|
|
status = "okay";
|
|
|
|
gmac1: mac@1 {
|
|
compatible = "mediatek,eth-mac";
|
|
reg = <1>;
|
|
phy-mode = "gmii";
|
|
phy-handle = <&int_gbe_phy>;
|
|
nvmem-cell-names = "mac-address";
|
|
nvmem-cells = <&macaddr_eeprom_0>;
|
|
};
|
|
};
|
|
|
|
&wifi {
|
|
status = "okay";
|
|
};
|