The dependency of kmod-usb3 and kmod-usb-xhci-pci-renesas have
been reversed. Now we need to select kmod-usb-xhci-pci-renesas
instead of kmod-usb3.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18768
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove modifications for codes guarded by CONFIG_USB_PCI_AMD.
This kernel symbol is only visible on desktop level platform,
e.g. x86. They are not sensitive to firmware image size. This
patch also fixes function redefinition build errors:
drivers/usb/host/pci-quirks.c:621:6: error: redefinition of 'usb_asmedia_modifyflowcontrol'
621 | void usb_asmedia_modifyflowcontrol(struct pci_dev *pdev)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/usb/host/pci-quirks.c:22:
drivers/usb/host/pci-quirks.h:49:20: note: previous definition of 'usb_asmedia_modifyflowcontrol' with type 'void(struct pci_dev *)'
49 | static inline void usb_asmedia_modifyflowcontrol(struct pci_dev *pdev) {}
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: be6753dda0 ("generic: 6.12: manually rebuild pending patches")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18637
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
New m4 release was made after a long time, for us most importantly
it ships newer gnulib so it compiles against GCC15 without forcing GNU17.
* Noteworthy changes in release 1.4.20 (2025-05-10) [stable]
** Fix a bug in the `eval' builtin where it does not suppress warnings
about division by zero that occurs within a more complex expression on
the right hand side of || or && (present since short-circuiting was
introduced in 1.4.8b).
** The `syscmd' and `esyscmd' builtins no longer mishandle a command line
starting with `-' or `+' (present since "the beginning").
** Fix regression introduced in 1.4.19 where trace output (such as with
`debugmode(t)') could read invalid memory when tracing a series of
pushed macros that are popped during argument collection.
** Fix regression introduced in 1.4.19 where the `format' builtin
inadvertently took on locale-dependent parsing and output of floating
point numbers as a side-effect of introducing message translations.
While it would be nice for m4 to be fully locale-aware, such a behavior
change belongs in a major version release such as 1.6, and not a minor
release.
** Fix regression introduced in 1.4.11 where the experimental `changeword'
builtin could cause a crash if given a regex that does not match all
one-byte prefixes of valid longer matches. As a reminder, `changeword'
is not recommended for production use, and will likely not be present
in the next major version release.
** On non-Unix platforms where binary files differ from text, loading a
frozen file (which should be cross-platform compatible) now correctly
uses binary mode.
** Several documentation improvements to the manual.
** Update to comply with newer C standards, and inherit portability
improvements from gnulib.
Link: https://github.com/openwrt/openwrt/pull/18821
Signed-off-by: Robert Marko <robimarko@gmail.com>
CONFIG_DRM_ACCEL_QAIC was not added to x86 generic config, but it needs to
be added as CONFIG_DRM_ACCEL_QAIC does not depend on x86_64 like others.
Fixes: 51b78aa ("kernel: package intel_vpu driver")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport GIC ITS support for RK356x SoC, which fixes long-standing
MSI/MSI-X bug. (Previously MSI-X could only work on one PCIe node)
e.g. [ 7.250882] r8125 0002:01:00.0: no MSI/MSI-X. Back to INTx.
Tested on Radxa E25 with kmod-r8125-rss driver.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/18800
Signed-off-by: Robert Marko <robimarko@gmail.com>
Replace RK356x RNG patch with upstream version to
add the tag flag them as upstreamed.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/18800
Signed-off-by: Robert Marko <robimarko@gmail.com>
Run 'make kernel_oldconfig' to get an up-to-date config.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/18800
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, the empty CONFIG_HOST_FLAGS_OPT will be overridden by
"-O2". Fix this issue by checking if its parent menuconfig symbol
CONFIG_OPTIMIZE_HOST_TOOLS was defined.
Fixes: e3bec5692c ("rules.mk: set default host tools GCC optimization level to -O2")
Reported-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18815
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, when you select the Default profile it does not honor DEFAULT:=n
nor BROKEN:=y in device profiles but rather just tries to build all of them.
This may work when building directly, but when using Image Builder it will
always fail since no kernel or anything else is present for devices that
have DEFAULT:=n or BROKEN:=Y set since those are skipped during build.
So, lets look for DEFAULT being set to "n" or BROKEN being set to "y" and
then remove clear _PROFILE_SET so they dont end up being marked for
installation.
Fixes: #18410
Link: https://github.com/openwrt/openwrt/pull/18814
Signed-off-by: Robert Marko <robimarko@gmail.com>
There are NAND IC-s that define 1-bit ECC as the minimal strength,
however that is unsupported by QPIC-SNAND as it only supports 4 or 8 bit
ECC.
Since most of these chips also support 4-bit ECC just fine, instead of
erroring out if 1-bit ECC is requested lets instead default to 4-bit ECC.
Fixes: 01b72ce61e ("qualcommax: ipq50xx: remove ECC user config from board files")
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18795
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update to current SSDK head for 6.12 compatibility.
We must disable warnings for missing declarations and prototypes since
whole SSDK is litered with them and actually fixing them is like doing
whack a mole.
Link: https://github.com/openwrt/openwrt/pull/18795
Signed-off-by: Robert Marko <robimarko@gmail.com>
It seems that kernel cleaned up its kernels so we need to include
<linux/of_platform.h> for of_platform_device_create().
Link: https://github.com/openwrt/openwrt/pull/18795
Signed-off-by: Robert Marko <robimarko@gmail.com>
Using devm_clk_get_enabled() allows simplification of the driver and
dropping of the .remove OP as well.
Link: https://github.com/openwrt/openwrt/pull/18795
Signed-off-by: Robert Marko <robimarko@gmail.com>
6.12 PWM core introduced a bunch of incompatible changes, namely removal
of manual module owner assignment, complete PWM struct allocation and usage
refactor, etc.
So, update the driver to follow other drivers in 6.12 so it compiles.
Link: https://github.com/openwrt/openwrt/pull/18795
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh kernel config by running kernel_menuconfig.
Manually enable CONFIG_HW_RANDOM and CONFIG_CRYPTO_DEV_QCOM_RNG as these
got somehow disabled by the refresh.
Link: https://github.com/openwrt/openwrt/pull/18795
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh 6.12 patches, those that failed automatic refresh were refreshed
manually.
DT bindings patches that failed were dropped as we dont use them in practice.
Link: https://github.com/openwrt/openwrt/pull/18795
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Link: https://github.com/openwrt/openwrt/pull/18795
Signed-off-by: Robert Marko <robimarko@gmail.com>
This patch can help save over 60% of package build time. -O2
optimization level is the default value before the commit
e8b470139c ("tools: add options to optimize host binaries").
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18812
Signed-off-by: Robert Marko <robimarko@gmail.com>
Version 6.14 - April 7, 2025
* Feature: list PHYs (--show-phys)
* Feature: target a specific PHY with some commands (--phy)
* Feature: more attributes for C33 PSE (--show-pse, --set-pse)
* Feature: source information for cable tests (--cable-test[-tdr])
* Feature: JSON output for module info (-m)
* Feature: misc RSS hash info improvements (-x)
* Feature: tsinfo hwtstamp provider (--{get,set}-hwtimestamp-cfg)
* Fix: fix wrong auto-negotiation state (no option)
* Fix: more explicit RSS context action (-n)
* Fix: print PHY address as decimal (no option)
* Fix: fix return value on flow hashing error (-N)
* Fix: fix JSON output for IRQ coalescing
* Fix: fix MDI-X info output (no option)
* Misc: code cleanup in module parsers
* Misc: provide module_info JSON schema
* Misc: add '-j' alias for --json
* Misc: provide AppStream metainfo XML
* Misc: update message descriptions for debugging output
Signed-off-by: Piotr Kubik <piotr.kubik@adtran.com>
Signed-off-by: Chad Monroe <chad@monroe.io>
Link: https://github.com/openwrt/openwrt/pull/18803
Signed-off-by: Robert Marko <robimarko@gmail.com>
CONFIG_IDPF is Intel(R) Infrastructure Data Path Function Support and it
should be disabled by default, if needed it can be packaged as a kmod.
Disable to prevent spreading out through target configs.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Noticed that CONFIG_HISILICON_ERRATUM_162100801 was being added to
qualcommax 6.12 config.
Since we dont support any Hisilicon chips, disable it in generic config
before it starts spreading in target configs.
Signed-off-by: Robert Marko <robimarko@gmail.com>
DRM_ACCEL symbols were not added to geode and legacy thus making the kernel
prompt for them on compilation.
Fixes: 51b78aaaae ("kernel: package intel_vpu driver")
Signed-off-by: Robert Marko <robimarko@gmail.com>
RFC4541, section 2.1.2 says:
Packets with a destination IP (DIP) address in the 224.0.0.X range
which are not IGMP must be forwarded on all ports.
And section 3 says:
In IPv6, the data forwarding rules are more straight forward because
MLD is mandated for addresses with scope 2 (link-scope) or greater.
The only exception is the address FF02::1 which is the all hosts
link-scope address for which MLD messages are never sent. Packets
with the all hosts link-scope address should be forwarded on all
ports.
However, currently when a listener on FF12::1 or FF12:🔢0:1 for
example joins then not only packets to these addresses but also for
FF02::1 won't be flooded to all ports anymore, too. Which violates
RFC4541.
This happens because A): They all map to the same ethernet multicast
address, that is 33:33:00:00:00:01. And B) the VLAN profile L2
unknown MC flood setting will only apply flooding of 33:33:00:00:00:01
if there is no specific listener registered for it.
So to fix this, avoid registering an MDB entry in the switch for
33:33:00:00:00:01 at all.
The downside of this is that FF12::1, FF12:🔢0:1 etc.
will always be flooded, too. However fixing the handling of 224.0.0.X
and FF02::1 and adhering to RFC4541 must have priority to avoid
undesired packetloss, to avoid breaking IPv4/IPv6.
Tested-on: ZyXEL GS1900-24HP v1
Fixes: cde31976e3 ("realtek: Add support for Layer 2 Multicast")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Link: https://github.com/openwrt/openwrt/pull/18769
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove property 'status = "disabled"' for partitions in Zyxel NBG7815.
This option is mainly used for NAND memory and here we have SPI memory.
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18787
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix "property has invalid length" warning for two devices:
- TP-Link EAP620 HD v1
- Zyxel NBG7815
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18787
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fixes the following warning:
[ 180.314652] NOHZ tick-stop error: local softirq work is pending, handler #08!!!
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Currently, non existing ipq-wifi package name is selected for
EAP625-Outdoor HD, so correct the name.
Fixes: 51c1ea08d0 ("qualcommax: ipq60xx: add TP-Link EAP625-Outdoor HD v1 support")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add package for linux intel_vpu driver for Intel NPU/VPU
Signed-off-by: Joe Zheng <joe.zheng@intel.com>
Link: https://github.com/openwrt/openwrt/pull/17904
Signed-off-by: Robert Marko <robimarko@gmail.com>
Intel NPU device is an AI inference accelerator integrated with Intel
client CPUs, starting from Intel Core Ultra generation of CPUs
(formerly known as Meteor Lake). It enables energy-efficient execution
of artificial neural network tasks.
The full device name is Neural Processing Unit, but the Linux kernel
driver uses the older name - Versatile Processing Unit (VPU).
This package is for NPU/VPU firmware.
Details in https://github.com/intel/linux-npu-driver
Intel VPU firmware is now part of linux-firmware.
The current FW file names in linux-firmware do not match intel vpu
driver, create links to fix it
details in
https://github.com/torvalds/linux/blob/master/drivers/accel/ivpu/ivpu_fw.c
Signed-off-by: Joe Zheng <joe.zheng@intel.com>
Link: https://github.com/openwrt/openwrt/pull/17904
Signed-off-by: Robert Marko <robimarko@gmail.com>
TP-Link EAP625-Outdoor HD is a 802.11ax AP claiming AX1800 support.
It is wall or pole mountable, and rated for outdoor use. It can only
be powered via PoE.
Hardware-wise, it is very similar to the older EAP610-Outdoor model.
Software-wise, I couldn't find a difference other than the board
data files, and device name. For this reason, the majority of the
devicetree from the EAP610-Outdoor is reused.
This device currently comes in a "v1", and "v1.6" version. The
"support-list" of the vendor firmware does not have a distinction
between these versions. This commit was tested on a 'V1.6" device.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512 MB
* Storage: 128MB NAND
* Ethernet:
* Gigabit RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Multi-color System LED (Green/Amber)
* Buttons:
* 1x Reset
* UART: 4-pin unpopulated header
* 1.8 V level, Pinout 1 - TX, 2 - RX, 3 - GND, 4 - 1.8V
Installation:
=============
Web UI method
-------------
Set up the device using the vendor's web UI. After that go to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
The connect to the machine via SSH:
ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>
Disable signature verification:
cliclientd stopcs
Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
* Go to System -> Firmware Update.
* Under "New Firmware File", click "Browse" and select the image
* Select "Update" and confirm by clicking "OK".
If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWRT.
NOTE: If ssh continues to complain that "no matching host key type
found. Their offer: ssh-rsa,ssh-dss" it likely means that yor distro
has completely disabled deprecated siphers in ssh. In that case, run
the ssh command from a docker container of an older distro.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot tplink_eap625-outdoor-hd-v1-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the commandline.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18584
Signed-off-by: Robert Marko <robimarko@gmail.com>
It was suggested that the pinctrl property of the mdio node should
include the PHY reset GPIO. Add them in.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18584
Signed-off-by: Robert Marko <robimarko@gmail.com>
I have an EAP625-Outdoor HD v1 that is very similar with the EAP610
Outdoor. It works with the EAP610 initramfs, without any obvious loss
of functionality. In order to prepare for supporting the EAP625, move
the common parts into a shared .dtsi.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18584
Signed-off-by: Robert Marko <robimarko@gmail.com>
It's the proper function to handle this stuff in.
The original patch abused the fact that the ath9k driver in init called
ath9k_init_platform to populate all the needed configuration. This is
the wrong place to do so and it also goes away in 6.13.
Move 553-ath9k_of_gpio_mask.patch contents to ath9k_of_init where they
belong.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18764
Signed-off-by: Robert Marko <robimarko@gmail.com>
The web-recovery of the Genexis EX400 validates uploaded images to fit
in the rootf_0 partition.
With OpenWrt, only the kernel is stored in this partition, leaving the
partition very small. Currently, the first factory release image won't
be accepted by the recovery interface after the OpenWrt installation.
Pad the image of the ubifs to 10MB. This allows the 24.10 release image
to be uploaded, enabling device recovery.
Signed-off-by: David Bauer <mail@david-bauer.net>
Clean the temporary directory the UBI image is generated from before
generation.
Currently it is removed after the image generation, which leads to files
possibly not being cleared after a build failure in this step.
Signed-off-by: David Bauer <mail@david-bauer.net>
bcm6328, bcm6362 and bcm6368 targets are missing a key config symbol which
prevents the NAND from working.
Fixes: f6c02b014d ("bmips: 6.1: refresh config and add missing symbols")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
CONFIG_PAHOLE_HAS_LANG_EXCLUDE is set depending on the pahole version
present, so it must be filtered out.
Signed-off-by: Robert Marko <robimarko@gmail.com>
During the build of perl, the following ICE was reported in
https://github.com/openwrt/packages/issues/24565 when targeting PowerPC:
during RTL pass: reload
blocksort.c: In function 'mainSort.isra':
blocksort.c:1011:1: internal compiler error: in patch_jump_insn, at cfgrtl.cc:1303
1011 | }
| ^
0x7d49cee29d8f __libc_start_call_main
../sysdeps/nptl/libc_start_call_main.h:58
0x7d49cee29e3f __libc_start_main_impl
../csu/libc-start.c:392
Please submit a full bug report, with preprocessed source (by using -freport-bug).
Please include the complete backtrace with any bug report.
See <http://bugs.openwrt.org/> for instructions.
The same issue also caused the CI failures in
https://github.com/openwrt/packages/pull/26501.
The issue only occurs with GCC 14.2.0, but not with the head of the
releases/gcc-14 maintenance branch; a bisect found that this patch fixes
it.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Link: https://github.com/openwrt/openwrt/pull/18797
Signed-off-by: Robert Marko <robimarko@gmail.com>
