Until now only the RTL930x devices make use of the following notation.
phy8: ethernet-phy@8 {
compatible = "ethernet-phy-ieee802.3-c22";
phy-is-integrated;
reg = <8>;
sds = <3>;
};
This indicates that the link is driven by a serdes directly without
external phy. As the devices have multiple serdes it must be clarified
what serdes is responsible for that port.
Nevertheless all other devices have the same requirements. E.g. RTL838x
usually drives port 24 from serdes 4 and port 26 from serdes 5. All this
currently works because the driver has a lot of hardcoded port/serdes
mapping.
Make the situation better by adding dts helpers that can describe the
topology as needed.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18851
Signed-off-by: Robert Marko <robimarko@gmail.com>
The switchcore node is the central location that describes the Realtek switch
register addresses starting at 0x1b000000. It will be used by current and
future regmap enabled device drivers. The upstream MDIO driver already makes
use of it by calling syscon_node_to_regmap(dev->parent->of_node);
In the current DTS base we have 3 issues that should be fixed:
- rtl838x.dtsi has a length of 0x20000 instead of 0x10000
- rtl839x.dtsi has a length of 0x20000 instead of 0x10000
- rtl931x.dtsi has no switchcore node at all
Align these mismatches with the "good" RTL930x template.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/18642
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Some RTL8380M-based devices have been around for a long time and use an
early A revision of the RTL8380M SoC. This revision has an issue with
the auxiliary MDIO controller, causing it to malfunction. This may lead
to device reboots when the controller is used.
Provide a bit-banged MDIO bus, which muxes the auxiliary MDIO pins to
their GPIO function. Although this will result in lower performance,
there should otherwise be no functional differences.
Link: https://github.com/openwrt/openwrt/issues/9534
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Add a disabled node for the auxiliary MDIO bus, used to manage the
RTL8231 expanders. A simple-mfd parent node is added, at the same
(implied) address as the switch@1b000000 node, as the switch drivers
should anyway transistion to MFD subdivices at some point.
Additionally, two pinctrl-single node are added to allow the MDX pins to
be muxed correctly, in case the bootloader leaves these unconfigured.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
There is no need to keep a version specific dts directory.
Rename the folder to its standard location.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
This patch adds "dts-5.10" directory to use backported drivers.
There are several specification changes in the new drivers, so there
are some compatibility issues in using dts/dtsi files for 5.4.
The old DTS files are moved to "dts-5.4", so their corresponding
kernel version is obvious as well.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[change "dts" to "dts-5.4", adjust Makefile]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds support for the RTL8390 and RTL9300 SoCs
it also cleans up unnecessary definitions in mach-rtl83xx.h
and moves definitions relevant for irq routing to irq.h
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
Move the memory out of the rtl838x.dtsi and into the device family DTSI
or device DTS if applicable. This aligns with upstream practice.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
[add missing block for dgs-1210-10p, move block below chosen node]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
