This allows us to use the full size of nand, which increases ubi size
from 64M to 122.25M.
If you are at factory firmware, please refer commit 63b8d98dd0 ("mediatek: add support for Cudy TR3000 v1")
to boot into OpenWrt initramfs (stock layout).
Flash instructions:
1. Login into the device and backup everything, especially 'Factory' part.
1. Unlock mtd partitions:
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
3. Write new BL2 and FIP
mtd write openwrt-mediatek-filogic-cudy_tr3000-v1-ubootmod-preloader.bin BL2
mtd write openwrt-mediatek-filogic-cudy_tr3000-v1-ubootmod-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Tested-by: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Upstream uses a different filename, so lets rename our downstream
mt7981.dtsi to mt7981b.dtsi and update the device tree of all
MT7981 boards accordingly.
This is to prepare for the switch to Linux 6.12 which is going to
use the upstream mt7981b.dtsi (plus some patches on top).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Same as commit 3674689, correct 'buswidth' to 'bus-width'.
Move the nmbm properties outside the partition definition.
Change uppercase to lowercase, add missing read-only flag.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
gpio is deprecated. Found with dtc's -Wdeprecated_gpio_property
Used git grep -E $'\tgpio = <' to make the changes.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15681
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Hardware:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 128 MiB SPI NAND
- RAM: 512 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- Ethernet: 1x 10/100/1000/2500 Mbps RTL8221B WAN, 1x10/100/1000 Mbps MT7981 LAN
- USB 3.0 port
- Buttons: 1 Reset button, 1 slider button
- LEDs: 1x Red, 1x White
- Serial console: internal test points, 115200 8n1
- Power: 5 VDC, 3 A
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:af:ca:xx:xx:x1 | label+1 |
| LAN | 80:af:ca:xx:xx:x0 | label |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label |
| WLAN 5g | 82:af:ca:xx:xx:x0 | |
+---------+-------------------+-----------+
Installation:
The installation must be done via TFTP by disassembling the router. On other occasions Cudy has distributed intermediate firmware to make installation easier, and so I recommend checking the Wiki for this device if there is a more convenient solution than the one below.
To install using TFTP:
1. Connect to UART.
2. With the router off, press the RESET button. While the router is turning on, the button should continue to be pressed for at least 5 seconds.
3. A u-boot shell will automatically open.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP server and an OpenWrt initramfs-kernel.bin firmware file.
5. Run these steps in u-boot using the name of your file.
setenv bootfile initramfs-kernel.bin
tftpboot
bootm
6. If you can reach LuCI or SSH now, just use the sysupgrade image with the 'Keep settings' option turned off.
Signed-off-by: Luis Mita <luis@luismita.com>
