Commit graph

9 commits

Author SHA1 Message Date
Álvaro Fernández Rojas
975f4de1c8 bmips: fix LAN LEDs configuration
Commit Fixes: 15430a1348 ("bmips: use wan ports as standalone ports")
removed bridge devices and therefore switch.1 no longer exists, so let's
use br-lan instead.

Fixes: 15430a1348 ("bmips: use wan ports as standalone ports")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2025-06-07 21:13:23 +02:00
Jonas Gorski
15430a1348 bmips: use wan ports as standalone ports
With the recent fixes backported to 6.12, b53 ports should now fully
work as standalone ports outside of a switch.

So move them out of the switch and use them as standalone ports, which
makes configuring easier as VLANs don't need to be defined and reserved
anymore to use the wan port.

Tested on DGND3700v1.

While most devices do not define a wan port, I dropped the
ucidef_set_bridge_device() from all devices for consistency.

Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
2025-06-07 09:58:19 +02:00
Daniel González Cabanelas
e1a55de7a7 bmips: add support for Actiontec R1000H
The  Actiontec R1000H is a gigabit wifi router, 2.4 GHz single band with
two external antennas. It comes with a coaxial HomePNA port.

Hardware:
 - SoC: Broadcom BCM6368
 - CPU: dual core BMIPS4350 V3.1 @400Mhz
 - RAM: 64 MB DDR
 - Flash: 32 MB parallel NOR
 - LAN switch: Broadcom BCM53115, 5x 1Gbit
 - LAN coaxial : 1x HPNA 3.1, CG3211 + CG3213
 - Wifi 2.4 GHz: Broadcom BCM4322 802.11bgn
 - USB: 1x 2.0
 - Buttons: 2x, 1 reset
 - LEDs: 7x
 - UART: yes

The HPNA hardware probably needs a firmware to make the coaxial port work.
In the OEM firmware, it's apparently sent with an utility (inhpna) through
the ethernet port.

Installation via CFE web UI:
  1. Connect the UART serial port.
  2. Power on the router and press enter at the console prompt to stop the
     bootloader.
  4. Browse to http://192.168.1.1 and upload the OpenWrt CFE firmware
  5. Wait a few minutes for it to finish

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2023-06-15 17:58:58 +02:00
Álvaro Fernández Rojas
c3b1ef2dfd bmips: add support for Comtrend WAP-5813n
The Comtrend WAP-5813n is a wifi gigabit router, 2.4 GHz single band with
two external antennas.

Hardware:
 - SoC: Broadcom BCM6369
 - CPU: dual core BMIPS4350 @ 400Mhz
 - RAM: 64 MB DDR
 - Flash: 8 MB parallel NOR
 - LAN switch: Broadcom BCM53115, 5x 1Gbit
 - Wifi 2.4 GHz: miniPCI Broadcom BCM4322 802.11bgn
 - USB: 1x 2.0 (optional)
 - Buttons: 3x (reset)
 - LEDs: yes
 - UART: yes

Installation via CFE web UI:
  1. Power off the router.
  2. Press reset button near the power switch.
  3. Keep it pressed while powering up during ~20+ seconds.
  4. Browse to http://192.168.1.1 and upload the firmware.
  5. Wait a few minutes for it to finish.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-11 18:31:23 +02:00
Álvaro Fernández Rojas
3baa45fbd8 bmips: add support for Comtrend VR-3025un
The Comtrend VR-3025un is a wifi gigabit router, 2.4 GHz single band with
two external antennas.

Hardware:
 - SoC: Broadcom BCM6368
 - CPU: dual core BMIPS4350 @ 400Mhz
 - RAM: 64 MB DDR
 - Flash: 8 MB parallel NOR
 - Ethernet LAN: 4x 100Mbit
 - Wifi 2.4 GHz: miniPCI Broadcom BCM43222 802.11bgn
 - USB: 1x 2.0
 - Buttons: 1x (reset)
 - LEDs: yes
 - UART: yes

Installation via CFE web UI:
  1. Power off the router.
  2. Press reset button near the antenna.
  3. Keep it pressed while powering up during ~20+ seconds.
  4. Browse to http://192.168.1.1 and upload the firmware.
  5. Wait a few minutes for it to finish.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-11 12:09:40 +02:00
Daniel González Cabanelas
71a6f45fdf bmips: add support for Netgear EVG2000
The Netgear EVG2000 is a wifi gigabit router, 2.4 GHz single band with
two internal antennas integrated in the main PCB.

Hardware:
 - SoC: Broadcom BCM6369
 - CPU: dual core BMIPS4350 V3.1 @400Mhz
 - RAM: 64 MB DDR
 - Flash: 16 MB parallel NOR
 - LAN switch: Broadcom BCM53115, 5x 1Gbit
 - Wifi 2.4 GHz: Broadcom BCM4322 802.11bgn
 - USB: 2x 2.0
 - Buttons: 2x, 1 reset
 - LEDs: 10x
 - FXS: 2x
 - UART: yes

Installation via CFE web UI:
  1. Power off the router and make a temporal TX-RX shortcircuit on the
     serial pins.
  2. Power on the router and wait 3 or more seconds
  3. Remove the TX-RX shortcircuit
  4. Browse to http://192.168.1.1 or http://192.168.0.1 and upload the
     firmware
  5. Wait a few minutes for it to finish

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2023-06-11 09:54:52 +02:00
Daniel González Cabanelas
ed79519b8d bmips: add support for Netgear DGND3700 v1, DGND3800B
The Netgear DGND3700 v1 and DGND3800B are the same device but with
different factory firmwares. It's an xDSL wifi router with a slim black
shiny casing and 4 PCB internal antennas connected via UFL to a miniPCI
detachable card.

Hardware:
 - SoC: Broadcom BCM6368
 - CPU: dual core BMIPS4350 V3.1 @400Mhz
 - RAM: 128 MB DDR
 - NOR Flash: 32 MB parallel (CFE and OS)
 - NAND flash: 128 MB (empty)
 - Ethernet LAN: 5x 1Gbit
 - Wifi 2.4 GHz: Broadcom BCM43222 802.11bgn
 - Wifi 5 GHz: Broadcom BCM43222 802.11abgn
 - USB: 2x 2.0
 - Buttons: 3x, 1 reset
 - LEDs: 11x
 - UART: yes

Installation via OEM web UI:
  1. Open the Netgear administration web interface, by default:
        http://192.168.0.1
	user: admin
        password: password
  2. Look for "upgrade firmware" and proceed
  3. Wait some minutes until it finishes

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2023-06-10 15:37:52 +02:00
Daniel González Cabanelas
e7a0b61397 bmips: add support for Observa VH4032N
The Observa VH4032N is an xDSL wifi router with a vertical white casing
and two internal antennas connected via UFL.

Hardware:
 - SoC: Broadcom BCM6368
 - CPU: dual core BMIPS4350 V3.1 @400MHz
 - RAM: 128 MB DDR
 - Flash: 32 MB parallel NOR
 - Ethernet LAN: 4x 100Mbit
 - Wifi 2.4/5 GHz: onboard Broadcom BCM43222 802.11abgn
 - USB: 3x 2.0
 - Buttons: 2x, 1 reset
 - LEDs: 8x, blue and red
 - UART: 1x

Installation via OEM web UI:
  1. Use the admin credentials to login via web UI
  2. Go to Managament->Update firmware and select the OpenWrt CFE firmware
  3. Press "Update Firmware" button and wait some minutes until it finish

Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
2023-06-09 19:44:28 +02:00
Álvaro Fernández Rojas
6fd8e0f943 bmips: add subtargets for each SoC
BMIPS is a generic arch that can be used for multiple Broadcom SoCs, each one
with its own specific drivers, so instead of having a huge kernel supporting
all of them, let's switch to a subtarget per SoC like other OpenWrt targets.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-10 10:04:08 +02:00