Directly call the function "get_linux_version()" to get the integer
kernel version number.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19172
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With the recent fixes backported to 6.12, b53 ports should now fully
work as standalone ports outside of a switch.
So move them out of the switch and use them as standalone ports, which
makes configuring easier as VLANs don't need to be defined and reserved
anymore to use the wan port.
Tested on DGND3700v1.
While most devices do not define a wan port, I dropped the
ucidef_set_bridge_device() from all devices for consistency.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
- Update subtarget configs for kernel 6.12.
- Refresh patches for kernel 6.12.
- Drop 210-revert-macronix-nand-block-protection.patch since brcmnand no longer
implements low level ops.
- Adapt bcm63268 gpio switches for 6.12 numbering.
- Add b53 pending patches from Jonas Gorski to fix system hangs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Specifications:
- SoC: Broadcom BCM63168 dual 400MHz MIPS
- Flash: 128MB NAND ESMT F59L1G81A
- RAM: 128MB DDR3
- Ethernet: 5x 1000M
- Wifi: BCM435F
- 1x USB 2.0 port
- 2x Button
- 11x LED
- Coax HPNA (unsupported)
- RJ11 xDSL (unsupported)
Install instructions:
The booloader will only install signed firmware so the image has to
be manually flashed.
- Set up a TFTP server on 192.168.1.0/24 to serve the initramfs image
- Interrupt the bootloader and run from RAM with
r 192.168.1.100:openwrt-bmips-bcm63268-actiontec_t1200h-initramfs.elf
- On the openwrt console, copy the wfi image using wget/tftp/scp, i.e
scp user@192.168.1.100:~/openwrt/bin/targets/bmips/bcm63268/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin /tmp/
- Erase half the flash partition where openwrt will be installed with
flash_erase -j /dev/mtd1 0 491
- Flash the openwrt image with
nandwrite -p /dev/mtd1 /tmp/openwrt-bmips-bcm63268-actiontec_t1200h-squashfs-cfe.bin
- Reboot
- Interrupt the bootloader again and use the c command to boot from
previous firmware if vendor image is loaded
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[Minor improvements to DTS file]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Specifications:
* SoC: BCM63168
* RAM: NT5CC64M16GP-DI, DDR3 128MiB
* NAND: W29N01HVSINA, 128MiB
* Ethernet: 4x1000M LAN, 1x 1000M WAN
* Serial interface: on board but not populated, 3.3V, 115200, 8N1
Notes:
* Use DSA for VLAN and switches
* Ethernet ports and USB works
* gpio-leds are not working
* WLAN, xDSL, and FXS are not going to work
Signed-off-by: Hang Zhou <929513338@qq.com>
[refactor, reorder, drop unneeded or not working stuff]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Specifications:
- SoC: Broadcom BCM63168 dual 400MHz MIPS
- Flash: 16MB SPI NOR W25Q128WFG
- RAM: 128MB DDR3 W631GG6KB-15
- Ethernet: 1x 1000M, 3x 100M
- Wifi: BCM435F
- 1x USB 2.0 port
- 3x Button
- 12x LED
Flashing via serial
- Connect to the 3.3V TTL UART on the board
(J6 pinout Vcc Rx Tx Gnd) at 115200-8-N-1
- Press any key in the serial console when powering up the board to enter
the CFE prompt
- Configure an interface on your workstation to static IP 192.168.1.100
and connect it to the board
- Start a TFTP server with the firmware image
- On the CFE prompt, enter the command
"f 192.168.1.100:openwrt-bmips-bcm63268-smartrg_sr505n-squashfs-cfe.bin"
Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[Remove unneeded LED labels]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The Comtrend VG-8050 is a wifi gigabit ethernet router, 2.4 GHz single band with
two external antennas.
Hardware:
- SoC: Broadcom BCM63169
- CPU: dual core BMIPS4350 @ 400Mhz
- RAM: 128 MB DDR
- Flash: 128 MB NAND
- LAN switch: Broadcom BCM53125, 5x 1Gbit
- Wifi 2.4 GHz: SoC (BCM63268) 802.11bgn
- USB: 1x 2.0 (optional)
- Buttons: 2x (reset)
- LEDs: yes
- UART: yes
Installation via CFE web UI:
1. Power off the router.
2. Press reset button near the power switch.
3. Keep it pressed while powering up during ~20+ seconds.
4. Browse to http://192.168.1.1 and upload the firmware.
5. Wait a few minutes for it to finish.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Now that JFFS2 cleanmarkers are supported on the standard nand_do_upgrade
function we can start using it on bmips.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
BMIPS is a generic arch that can be used for multiple Broadcom SoCs, each one
with its own specific drivers, so instead of having a huge kernel supporting
all of them, let's switch to a subtarget per SoC like other OpenWrt targets.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
