The previous host installation fix accidentally moved the rpath settings
out of CMAKE_HOST_OPTIONS and into CMAKE_OPTIONS.
Fixes: ae42ecaad4 ("ucode: fix host installation")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The busybox built with mips16 enabled has broken seq command.
Disassembling shows that the call to hard-float strtod in mips16
code is generated without the __call_stub_fp:
```
0x00406d6f <+118>: lw v0,32(sp)
0x00406d71 <+120>: sll s0,2
0x00406d73 <+122>: addu s0,v0,s0
0x00406d75 <+124>: lw a0,-4(s0)
0x00406d79 <+128>: jal 0x44ebc1 <strtod@mips16plt>
0x00406d7d <+132>: addiu a1,sp,84
0x00406d7f <+134>: sw v0,64(sp)
0x00406d81 <+136>: lw v0,0(s1)
0x00406d83 <+138>: sw v1,68(sp)
```
As a result, strtod returns the result in float point registers
while the calling mips16 code expect the result in v0/v1.
Disable mips16 on hard-float targets for now. The built .ipk goes
from 213316 bytes to 251419 bytes.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The path for linking libucode.so was not specified for the ucode binary.
This breaks execution of ucode in the host context.
Signed-off-by: David Bauer <david.bauer@uniberg.com>
The company Zyxel rebranded some years ago.
Currently the casing is according to the old branding even
for newer devices which already use the new branding.
This commit aligns the casing of Zyxel everywhere.
Signed-off-by: Goetz Goerisch <ggoerisch@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15652
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
When running a failsafe shell on a console, job control was unavailable,
and ^C did not function correctly.
This change invokes console failsafe shells via `setsid`, making them
session leaders and allowing them to claim controlling terminals, which
makes job control function properly. To support this, the busybox
`setsid` utility is enabled. This has a minimal 149-byte size impact on
a test x86_64 squashfs rootfs image.
^C was ignored in subprocesses of failsafe shells: it was not possible
to ^C out of a program that would not exit on its own, such as many
typical `ping` invocations. As job control was unavailable, it was not
possible to suspend these subprocesses either, causing a hung program to
tie up a console indefinitely, unless another means to signal the
program was available. This was caused by SIGINT being placed at
disposition SIG_IGN by the shell running preinit, which it did because
the console shell was executed asynchronously with &. That disposition
was inherited by the console shell and its subprocesses, generally
causing ^C to have no effect.
As there is no way in busybox `ash` to reset the disposition of a signal
already ignored at shell entry, and no apparent way to avoid SIGINT
being placed at SIG_IGN when & is used in preinit, an alternative
construct is needed. Now, `start-stop-daemon` is used to start (-S) the
console failsafe shell in the background (-b). This approach does not
alter SIGINT, allowing the console shell to be started with that
signal's handling intact, and normal ^C processing to occur.
busybox `ash` has some behaviors conditional on SHLVL, and while the
console shells ought to run at SHLVL=1, they were not by virtue of being
started by the shell-based preinit system. Additionally, a variety of
detritus was present in the console shell's environment, carried over
from preinit. These conditions are corrected by running the console
shell via `env -i` to clear the environment and establish a minimum and
correct set of environment variables for operation, in the same manner
as `login`. HOME is not explicitly set, because it's addressed in
/etc/profile. For non-failsafe console shells when
system.@system[0].ttylogin = 0, `login -f root` achieves a similar
effect. (`login` already started non-failsafe console shells when
ttylogin = 1 and behaved correctly. This brings the ttylogin = 0 case to
parity.) Note that even `login -f` is somewhat undesirable for failsafe
shells because it requires a viable /etc/passwd, hence the `env -i`
construct in that case.
The TERM environment variable from the preinit environment, with value
"linux", would rarely be correct for serial consoles. Now, the preinit
TERM value is preserved (or set to "linux" if unset) only when the
console is /dev/console or /dev/tty[0-9]*. Otherwise, it will be set to
a safe default appropriate for serial consoles, "vt102", as used for
serial consoles by busybox init. This "linux"/"vt102" TERM setting is
also duplicated for non-failsafe console shells.
This also indicates failsafe mode by showing "- failsafe -" on all
consoles (not just the last-defined one). It sets a hostname of
"OpenWrt-failsafe" in failsafe mode which is rendered in the shell's
prompt as a reminder of the mode during interactive failsafe use.
Previously, no hostname was set, which resulted in the kernel-default
hostname, "(none)", appearing in failsafe shell prompts.
Signed-off-by: Mark Mentovai <mark@mentovai.com>
Link: https://github.com/openwrt/openwrt/pull/16113
Signed-off-by: Robert Marko <robimarko@gmail.com>
To better acommodate with the current browsers' requirements, also
self-signed certificates should have subjectAltName and
extendedKeyUsage defined in the self-signed x509 SSL certificates.
The following case sensitive options are now possible:
-addext subjectAltName=DNS:...
-addext subjectAltName=EMAIL:...
-addext subjectAltName=IP:...
-addext subjectAltName=URI:...
-addext extendedKeyUsage=serverAuth OR -addext extendedKeyUsage=any
Initial draft by Paul Donald <newtwen@gmail.com>
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
Link: https://github.com/openwrt/openwrt/pull/15366
Signed-off-by: Robert Marko <robimarko@gmail.com>
Bump omnia-mcutool to 0.3-rc3:
* The `--upgrade` option will now work even if MCU is in bootloader (for
example if previous upgrade was aborted).
* On boards with GD32 MCUs, `omnia-mcutool` will now refuse to upgrade
application firmware to version lower than 4.1 if bootloader version
is 2.0 (the original for first batch of boards with GD32 MCUs) since
these versions of application and bootloader are not compatible.
If user already upgraded to such a combination, an upgrade of
bootloader firmware is required.
The `--upgrade` option will inform about this and will automatically
upgrade bootloader firmware if the `--force` option is given.
(Note that version 4.1 of the MCU firmware was will be released soon,
once it is properly tested.)
* Various other improvements.
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/16086
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add a new utility, omnia-mcutool, which main purpose is to upgrade the
firmware on the microcontroller on the Turris Omnia router. Depends on
omnia-mcu-firmware, and the upgrade process is pretty simple:
omnia-mcutool --upgrade
Besides firmware upgrade, the utility can be used to show and configure
various firmware settings.
Signed-off-by: Marek Mojík <marek.mojik@nic.cz>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://github.com/openwrt/openwrt/pull/13799
Signed-off-by: Robert Marko <robimarko@gmail.com>
Mark the package as nonshared to build it in the target specific build
step 1 of the build bots instead of the architecture generic build step
2. In the build step 2 it may be left out if we build it using a
different target.
Fixes: 24d6abe2d7 ("firmware-utils: new package replacing otrx")
Link: https://github.com/openwrt/openwrt/pull/16031
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mark the package as nonshared to build it in the target specific build
step 1 of the build bots instead of the architecture generic build step
2. In the build step 2 it may be left out if we build it using a
different target.
Fixes: 8619d7af67 ("kirkwood: add D-Link DNS-320L support")
Link: https://github.com/openwrt/openwrt/pull/16031
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move shell functions used for sysupgrade into /lib/upgrade/fit.sh.
Introduce improved fitblk boot device detection function which
works also in case ubiblock devices have not yet been created or
even UBI itself not yet being attached.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
73644a036f5a nl80211: move access to tb array out of uc_nl_convert_attr and below
6e3cf83a77a7 nl80211: add support for multi-attribute arrays
6ff24d5488a9 nl80211: update nl80211.h to latest wireless-next
abc2aef28641 nl80211: add wiphy multi-radio support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
`f2fslabel` is already built into `f2fs.fsck`, but is missing its symlink
in the final package.
Signed-off-by: Sean Khan <datapronix@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/15851
Signed-off-by: Robert Marko <robimarko@gmail.com>
These things already get built and installed by tools/e2fsprogs. No need
to duplicate.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15822
Signed-off-by: Robert Marko <robimarko@gmail.com>
Release notes:
https://lists.infradead.org/pipermail/linux-mtd/2024-March/104058.html
mtd-utils are currently depending on zlib, however it is not expressed
as a dependency and it is somehow being only pulled-in by lincurses-devel
so mtd-utils were able to compile.
Since 2.2.0 zlib is optional so lets disable support for it like for other
compressors since we dont package the mkfs.ubifs or mkfs.jffs2 that
are only users of compressors anyway.
Link: https://github.com/openwrt/openwrt/pull/15802
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that we are not patching mtd-utils with JFFS2 LZMA support there
is no need for autoreconf to be run.
Link: https://github.com/openwrt/openwrt/pull/15802
Signed-off-by: Robert Marko <robimarko@gmail.com>
We have been carrying the 100-fix_includes.patch and 130-lzma_jffs2.patch
for a long time but the reason is lost to history.
We dont need to carry the JFFS2 LZMA support patch as mkfs.jffs2 is not
even being packaged so its not even being used.
As for the 100-fix_includes.patch that also seems like a relic of history
as mtd-utils compiles fine without it.
So, lets drop both patches.
Link: https://github.com/openwrt/openwrt/pull/15790
Signed-off-by: Robert Marko <robimarko@gmail.com>
224d497dd94f srec2bin: drop unused "dum" variable
6777b2d51961 uimage_sgehdr: use "char" type for header struct strings
81db3025aac5 uimage_sgehdr: drop unused "ltmp" variable
bd7fcc74b43e pc1crypt: make decrypt/encrypt functions take void * as argument
6ac44974185a linksys: add magic header generation tool for e8350 v1
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Since musl 1.2.5 update yafut would throw a warning about implicit
declaration of basename() but would still somehow compile.
However, trying to use it on a device will cause it to instantly
Segmentation fault.
So, to fix this lets update to the current upstream repository version
that has removed the use of basename() completely.
Link: https://github.com/openwrt/openwrt/pull/15685
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use the same Yafut code revision for both updating devices with NAND
flash and preparing firmware images for devices with NOR flash.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
Link: https://github.com/openwrt/openwrt/pull/13453
Signed-off-by: Robert Marko <robimarko@gmail.com>
Dual-slot NAS based on Marvell Kirkwood.
Specifications:
- Marvell 88F6702 @1GHz
- 256Mb RAM
- 128Mb NAND
- 1x GbE LAN (Marvell 88E1318R)
- 1x USB 2.0
- 2x SATA
- Weltrend WT69P3 ("supervisor" MCU chip)
- Serial on J2 (115200,8n1)
- Newer bootROM so kwboot-ing via serial is possible
Notes:
- The Weltrend MCU is controlled by the package added in utils/dns320l-mcu.
- The original MAC address is stored in the "mini firmware" image's first
17 bytes.
- Compared to the original MTD layout, the uImage+rootfs are now stored in
a common ubi partition.
Installation:
1. Serial console
- Connect your levelshifter to the serial console
on J2 (refer to the wiki page for pinout)
2. Update u-boot
- Download the u-boot.kwb image for the device
- Powercycle the NAS
- Run "kwboot -b u-boot-dns320l/u-boot.kwb /dev/ttyUSB0 -p"
- Connect to the serial console with minicom
- tftp 0x0800000 u-boot-dns320l/u-boot.kwb
(Please note that "PHY reset timed out" seems to be customary
on kirkwood devices, the egiga0 interface works regardless.)
- nand erase 0x0 100000
- nand write 0x0800000 0x0 0x100000
- reset
3. Install OpenWrt
- Boot up the initramfs image
- tftpboot 0x800000 openwrt-kirkwood-generic-dlink_dns320l-initramfs-uImage; bootm 0x800000
- Download the sysupgrade image and perform sysupgrade
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
This 4G/LTE modem is a WiFi hotspot, and also works as cdc_ether modem
when plugged over USB. It needs usb-modeswitching. With HuaweiNewMode,
it will modeswitch from 3426:1f01 (mass-storage) to 3426:14db
(cdc_ether).
Signed-off-by: Didier 'OdyX' Raboud <odyx@raksha.ch>
Link: https://github.com/openwrt/openwrt/pull/15497
Signed-off-by: Robert Marko <robimarko@gmail.com>
The 'nandbiterrs' tool is useful to find out of bit error correction of
NAND is working as expected by deliberately introducing bit errors and
telling up to which number they can be corrected.
Enable build of the testing tools and package the 'nandbiterrs' tool as
part of the nand-utils package.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Changes:
- new URL for sources (old address is dead)
- daemon and utils from packages feed are merged in here
- only build once
- no need to update at the same time in both places
- update to v3.1.4
- removed unneeded patches
- added audisp-syslog
- removed audispd (no longer exists)
- rename and move to package/utils/audit
- update new path in one dependent package
Signed-off-by: Marius Dinu <m95d+git@psihoexpert.ro>
With the switch to ZSTD for git clone packaging, hashes have changed so
fixup remaining package hashes that were missed in the inital update.
Fixes: b3c1c57 ("treewide: update PKG_MIRROR_HASH to zst")
Signed-off-by: Robert Marko <robimarko@gmail.com>
When using zst instead of xz, the hash changes. This commit fixes the
hash for packages and tools in core.
Signed-off-by: Paul Spooren <mail@aparcar.org>
With the change in version schema the downloaded files changed, too,
mostly the hash is now prefixed with a tilde `~` instead of a dash `-`.
Since each downloaded archive contains folder with the same name as the
archive, the checksum changed.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Different from OPKG, APK uses a deterministic version schema which chips
the version into chunks and compares them individually. This enforces a
certain schema which was previously entirely flexible.
- Releases are added at the very and end prefixed with an `r` like
`1.2.3-r3`.
- Hashes are prefixed with a `~` like `1.2.3~abc123`.
- Dates become semantic versions, like `2024.04.01`
- Extra tags are possible like `_git`, `_alpha` and more.
For full details see the APK test list:
https://gitlab.alpinelinux.org/alpine/apk-tools/-/blob/master/test/version.data
Signed-off-by: Paul Spooren <mail@aparcar.org>
this patch separates libe2p from e2fsprogs package, like all other
provided libraries are their own packages. Also some development headers
were missing so I added those along with pkg-config files.
Signed-off-by: Oskari Rauta <oskari.rauta@gmail.com>
Add minimalistic tool to allow releasing /dev/fit* devices which is
needed on sysupgrade when using the fitblk driver.
The package is hidden in menuconfig, it should only be selected by
adding it to the default package selection of boards using it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It appears `md5` is no longer state of the art. Let's switch it to
something slightly newer to increase security.
Suggested-by: abnoeh <abnoeh@mail.com>
Signed-off-by: Paul Spooren <mail@aparcar.org>
The raspberypi/userland repository has been deprecated and the RPi tools have
been moved to the raspberrypi/utils repository.
96a7334ae9
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This is the last update for bcm27xx-userland as it has been
deprecated but funcional up to raspberry pi 5.
96a7334 README: Update to make it clear that most code in this repo is deprecated
3c97f76 userland: dtoverlay: /boot/firmware is a valid path
153a235 Assorted clang static analysis fixes
eca070c bcm_host: Update kms/fkms check for pi5
06a7618 dtoverlay: Support bcm2712 as a platform
0489c07 dtoverlay: Add dtoverlay_first/next_subnode
a1c7f81 dtoverlay: Support literal assignments of path strings
44a3953 raspivid: Also flush PTS file if flush is enabled
cc1ca18 userland: dtoverlay: Use os_prefix if set
9d5250f libfdt: Add null-ptr check for prop-data to resolve clang --analyzer warning
50527c6 mmal: Only include Videocore components if not running on Videocore
df245ea tvservice: Update unsupported message to recommend kmsprint
de0cfe8 dtoverlay: Fix clang warnings
0182f05 dtoverlay: Fix various compiler warnings
2a6306b dtoverlay: Fix path rebasing and exports
d1e92d7 dtoverlay: Add support for string escape sequences
b1ee39e gencmd: Add a fallback to mailbox interface if vchiq is not available
54fd97a hello_pi: Fix some build issues
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Setting up usb gadgets using g_* kernel modules are considered a
legacy approach, but the usb_gadget configfs is a bit annoying
to use directly.
The usb_gadget configfs works by creating magic directories
and writing to magic files under /sys/kernel/config/usbgadget.
This new package is an init script to setup usb_gadget configfs
using uci. In the config file, gadget/configuration/function
sections create corresponding directories. UCI options are magic
files available in the configfs and strings/0x409 directories,
grabbed with a 'find' command. UDC option in gadget writes
the UDC file under the 'gadget' directory to attach the
generated gadget config.
It's also possible to apply pre-made config templates under
/usr/share/usbgadget. The templates use the same UCI config
format, with the 'gadget' entry named 'g1'. Currently, there
are templates for CDC-ACM and CDC-NCM gadgets written based
on existing g_*.ko module code.
Certain SBCs come with only a USB device port (e.g. Raspberry Pi
Zero). With this script, it's now possible to perform initial
setup on them by adding a default NCM gadget.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Fix typo calling lua53 instead of lua5.3 for Package Default definition.
This cause only missing description of the package and doesn't cause
any build regression.
Fixes: c52ca08d40 ("lua5.3: build shared library")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Let ucode-mod-* packages select the ucode interpreter instead of depending
on it to avoid recursive dependency chains in unrelated packages.
Fixes: https://github.com/openwrt/packages/issues/22837
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This fixes the mirror hash to the version of the file uploaded to the
download mirror and which my build calculated.
Fixes: b117e7244f ("firmware-utils: update to Git HEAD (2023-11-21)")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
1d42292d8063 tplink-safeloader: Add TP-Link Archer A6 V3.20
3338f5389d72 tplink-safeloader: add TL-WPA8635P v3
17ca5eeb1c10 tplink-safeloader: add TL-WPA8631P v4
f730ad2fa0b4 bcmblob: new tool for reading Broadcom's BLOBs
cb1ddac98124 firmware-utils: fix typo in error message when no OpenSSL library found
916633160dc9 bcmclm: new tool for reading Broadcom's CLM data
a2d49fb1e188 tplink-safeloader: add RU support-list entry for Archer C6U v1
bb12cf5c3fa9 tplink-safeloader: Add support for TP-Link Deco M5 The special_id values are the same for EU and Asian models, and they apply to all models: v1, v2, and v3. They are not sorted as they are currently in the same order as extracted from the official firmware image.
9e2de8515be1 tplink-safeloader: add EAP610 v3 and EAP613 v1
a170683c0e11 firmware-utils: fix use of NULL string progname
89875fc18b57 tplink-safeloader: CPE510: add Canadian support
9e211d2980fe mktplinkfw2: add support to extract bootloader images
c18f662f3c74 mktplinkfw2: add support to pack bootloader
3dc133915f87 mktplinkfw2: show exact exceed bytes when the image is to big
d16ff798d58a tplink-safeloader: WPA8631: add v4 AU, US
0fa1cc51013f zytrx: add LTE5398-M904
635466123429 firmware-utils: ptgen: add SiFive GPT partition support
ba5bc4e1ae9d add dlink-sge-image for D-Link devices by SGE
3b114de29cf7 lxlfw: move code opening LXL to helper function
8e149e480391 lxlfw: move code copying data to helper function
16fa89076122 lxlfw: fix struct lxl_hdr attribute
d770cab82e58 lxlfw: support embedding blobs
eaf2ea28dbe6 lxlfw: support extracting image
12bf1a99bd6e lxlfw: support certificate & signature blobs
Fixes: https://github.com/openwrt/openwrt/issues/12939
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Information about package license is important, so lets add it.
Fixes: 79ee0d2cee ("debugcc: add new package to debug IPQ based SoC clocks")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
I find myself manually compiling dtc as a staticly linked binary rather
often while porting a new device to OpenWrt as dtc is rarely included in
various vendor modifications of OpenWrt.
So, since dtc offers a convenient meson option to build it as staticaly
linked binary, lets make it a compile time option.
Signed-off-by: Robert Marko <robimarko@gmail.com>
0352a33 uloop: support new interval and signal APIs
1468cc4 syntax: don't treat `as` and `from` as reserved keywords
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Store the private key with read and write permission for the user only
and not with read permissions for everyone. This converts the
write_file() function from fopen() to open() because open allows to
specify the permission mask of the newly created file. It also adds and
fixes some existing error handling.
OpenSSL does this in the same way already.
With this change it looks like this:
root@OpenWrt:/# ls -al /etc/uhttpd.*
-rw-r--r-- 1 root root 749 Nov 6 23:14 /etc/uhttpd.crt
-rw------- 1 root root 121 Nov 6 23:14 /etc/uhttpd.key
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Store the private key with read and write permission for the user only
and not with read permissions for everyone. This converts the
write_file() function from fopen() to open() because open allows to
specify the permission mask of the newly created file. It also adds and
fixes some existing error handling.
OpenSSL does this in the same way already.
With this change it looks like this:
root@OpenWrt:/# ls -al /etc/uhttpd.crt /etc/uhttpd.key
-rw-r--r-- 1 root root 519 Nov 6 22:58 /etc/uhttpd.crt
-rw------- 1 root root 121 Nov 6 22:58 /etc/uhttpd.key
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes building with USE_LTO enabled.
<artificial>:(.text+0xcc8): relocation R_MIPS16_26 against `luaL_argerror' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol strcpy
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
Remove ABI version, since its format is not accepted by the linker.
Enable rpath to avoid clash with system libraries
Signed-off-by: Felix Fietkau <nbd@nbd.name>
1) clear nvram partialboots upon successful boot
This behavior is already defined for EA9500; enabled for EA9200 too.
2) fix MAC address in board.d/02_network
Use the correct nvram variable to derive lan/wan MAC address.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
Add missing PKG_MIRROR_HASH. This is always needed as is used to
generate and use a tar instead of git clone and validate the hash of it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The PKG_CPE_ID links to NIST CPE version 2.2.
Assign PKG_CPE_ID to all remaining package which have a CPE ID.
Not every package has CPE id.
Related: https://github.com/openwrt/packages/issues/8534
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
350b960 add support for multi GNSS solutions
fb87d0f ugps: add baud rate command line option
a8171a0 main.c: -S does not take any options
Build-tested: ramips/ltap-2hnd
Run-tested: ramips/ltap-2hnd
Signed-off-by: Arne Zachlod <arne@nerdkeller.org>
Hardware
--------
CPU: Mediatek MT7981
RAM: 512M DDR4
FLASH: 256M NAND
ETH: MaxLinear GPY211 (2.5GbE N Base-T)
WiFi: Mediatek MT7981 (2.4GHz 2T2R:2 5GHz 3T3R:2 802.11ax)
BTN: 1x Reset
LED: 1x Multi-Color
UART Console
------------
Available below the rubber cover next to the ethernet port.
Settings: 115200 8N1
Layout:
<12V> <LAN> GND-RX-TX-VCC
Logic-Level is 3V3. Don't connect VCC to your UART adapter!
Installation Web-UI
-------------------
Upload the Factory image using the devices Web-Interface.
As the device uses a dual-image partition layout, OpenWrt can only
installed on Slot A. This requires the current active image prior
flashing the device to be on Slot B.
In case this is not the case, OpenWrt will boot only one time, returning
to the ZyXEL firmware the second boot.
If this happens, first install a ZyXEL firmware upgrade of any version
and install OpenWrt after that.
Installation TFTP / Recovery
----------------------------
This installation routine is especially useful in case of a bricked
device.
Attach to the UART console header of the device. Interrupt the boot
procedure by pressing Enter.
The bootloader has a reduced command-set available from CLI, but more
commands can be executed by abusing the atns command.
Boot a OpenWrt initramfs image available on a TFTP server at
192.168.1.66. Rename the image to nwa50axpro-openwrt-initramfs.bin.
$ atnf nwa50axpro-openwrt-initramfs.bin
$ atna 192.168.1.88
$ atns "192.168.1.66; tftpboot; setenv fdt_high 0xffffffffffffffff;
bootm"
Upon booting, set the booted image to the correct slot:
$ zyxel-bootconfig /dev/mtd9 get-status
$ zyxel-bootconfig /dev/mtd9 set-image-status 0 valid
$ zyxel-bootconfig /dev/mtd9 set-active-image 0
Copy the OpenWrt sysupgrade image to the device using scp.
Write the sysupgrade image to NAND using sysupgrade.
$ sysupgrade -n image.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
colrm is already built, package just isn't generated.
colrm can be used to remove columns from file/stdin.
Use cases vary, personally I needed it because I build openwrt
natively - and wolfssl configure script wants either colrm, or cut
but busybox's cut isn't accepted.
Built: x86_64, latest git
Tested: x86_64, latest git
Signed-off-by: Oskari Rauta <oskari.rauta@gmail.com>
Safely detect integer overflow in try_addint() and try_subint().
Old code relied on undefined behavior, and recent versions of GCC on x86
optimized away the if-statements.
This caused integer overflow in Lua code instead of falling back to
floating-point numbers.
Signed-off-by: Adam Bailey <aebailey@gmail.com>
commit c0611b45a9 ("e2fsprogs: symlink e2fsck to fsck.ext{2, 3, 4},
and tune2fs to findfs") introduced a symlink from tune2fs to findfs.
This only works when the included private libblkid library is used, but
commit 5b1660a538 ("utils/e2fsprogs: Update to 1.43.6") disabled the
usage of this private lib and enabled the shared lib support.
Removing this symlink makes it possible to install tune2fs and findfs
package.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
It's required by bcm53xx. This allows dropping separated oseama package
and avoids some code duplication.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Some of firmware utils may be required on target devices. It's useful
e.g. for dealing with some firmware formats. That is often required
(supporting specific format) to provide an option to revert to original
firmware.
So far we had packaged "otrx" util only for use on Broadcom targets.
Refactor that to package the whole firmware-utils project so we can
package any single util needed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Release Notes:
http://lists.busybox.net/pipermail/busybox-cvs/2023-May/041510.html
Refresh commands, run after busybox is first built once (nothing changed
compared to 1.36.0):
cd package/utils/busybox/config/
../convert_menuconfig.pl ../../../../build_dir/target-mipsel_24kc_musl/busybox-default/busybox-1.36.1
cd ..
./convert_defaults.pl ../../../build_dir/target-mipsel_24kc_musl/busybox-default/busybox-1.36.1/.config > Config-defaults.in
Manual edits needed afterward:
* Config-defaults.in: OpenWrt config symbol IPV6 logic applied to
BUSYBOX_DEFAULT_FEATURE_IPV6
* Config-defaults.in: OpenWrt config TARGET_bcm53xx logic applied to
BUSYBOX_DEFAULT_TRUNCATE (commit 547f1ec)
* Config-defaults.in: OpenWrt logic applied to
BUSYBOX_DEFAULT_LOGIN_SESSION_AS_CHILD (commit dc92917)
* Config-defaults.in: correct the default ports that get reset
BUSYBOX_DEFAULT_FEATURE_HTTPD_PORT_DEFAULT 80
BUSYBOX_DEFAULT_FEATURE_TELNETD_PORT_DEFAULT 23
* config/editors/Config.in: Add USE_GLIBC dependency to
BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090)
* config/shell/Config.in: change at "Options common to all shells" the conditional symbol
SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH
(discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html
Apparently our script does not see the hidden option while
prepending config options with "BUSYBOX_CONFIG_" which leads to a
missed dependency when the options are later evaluated.)
* Edit a few Config.in files by adding quotes to sourced items in
config/Config.in, config/networking/Config.in and config/util-linux/Config.in (commit 1da014f)
Tested-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Nick Hainke <vincent@systemli.org>
The getrandom syscall is not hanging at bootup any more if there is
not enough entropy. This was fixed upstream in 2018 in commit:
a9cf659e05
This OpenWrt patch is not needed any more.
This reverts commit e64463ebde ("util-linux: avoid using the getrandom syscall")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes the following error:
* check_data_file_clashes: Package taskset wants to install file build_dir/target-powerpc_8548_musl/root-mpc85xx/usr/bin/taskset
But that file is already provided by package * busybox
* opkg_install_cmd: Cannot install package taskset.
Fixes: 3c3d797c4d ("busybox: enable taskset by default")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove upstramed patches:
- 100-configure.ac-fix-AC_ARG_WITH.patch
- 101-configure.ac-fix-cross-compilation.patch
Remove deprecated f2fstat tool:
https://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs-tools.git/commit/?id=77bf7ed29f1dd1341079913f3b36fc62f812c4f5
Changelog:
06c027a f2fs-tools: upgrade version 1.16.0
542cc57 fsck.f2fs: fix sanity check logic for cp_payload
a7df89e mkfs.f2fs: remove indentation
c82985a fsck.f2fs: don't call report_zone on normal partition
0ac168e f2fs-tools: relax zone size of power of 2
641be32 mkfs.f2fs: trim all the devices except the first one
3835fef f2fs-tools: fix # of total segments
5b08ca9 f2fs_io: support AES_256_HCTR2
ae3301c f2fs_io: Fix out of tree builds
ddbde27 fsck.f2fs: relocate chksum verification step during f2fs_do_mount()
77bf7ed f2fs-tools: Remove deprecated f2fstat
fb6575e Remove sg_write_buffer
1bb669e fsck.f2fs: avoid uncessary recalculation
ccd2361 fsck.f2fs: fix potential overflow of copying i_name
cd6b133 fsck.f2fs: add parentheses for SB_MASK
399600a dump.f2fs: remove unavailable option -g
3e6e178 f2fs-tools: define HAVE_CLOCK_GETTIME properly
907b972 f2fs-tools: support F2FS_IOC_START_ATOMIC_REPLACE
9ff70fb f2fs-tools: give less overprovisioning space
844f821 f2fs-tools: set host-aware zoned device similar to host-managed one
88ac76d fsck.f2fs: fix missing to assign c.zoned_model
8cbe34e fsck.f2fs: trigger repairing if filesystem has inconsistent errors
2f1dde2 fsck.f2fs: trigger repairing if filesystem was forced to stop
465159f fsck.f2fs: export valid image size
3486b62 mkfs.f2fs: update allocation policy for ro feature
bdd51e5 fsck.f2fs: fix __end_block_addr()
5a5e419 Always use sparse/sparse.h when building for Android
19f77c6 f2fs-tools: fix build error on lz4-1.9.4
986c1f1 Fix format strings in log messages
0d6acbe fsck.f2fs: use elapsed_time in checkpoint for period check
9b7a4c5 mkfs.f2fs: catch total_zones=0 instead of crashing
6148db3 f2fs-tools: use F2FS_BLKSIZE instead of PAGE_*_SIZE
f09c2b7 f2fs_io: support triggering filesystem GC via ioctl
32e7d27 configure.ac: fix cross compilation
65fe94e configure.ac: fix AC_ARG_WITH
6325cf7 Use F2FS_BLKSIZE as the size of struct f2fs_summary_block
c89be7a Use F2FS_BLKSIZE for dev_read_block() buffers
5317d18 Improve compile-time type checking for f2fs_report_zone()
92e2e52 Fix f2fs_report_zone()
648a491 Fix the struct f2fs_dentry_block definition
c964547 resize.f2fs: add option to manually specify new overprovision
a741438 fsck.f2fs: drop compression bit if inline_data is set
406b1c9 f2fs-tools: fix cannot get bdev information
9d0cb9e f2fs_io: add dsync option for write
a7b8b46 tools: fix file too large causing overflow
bddca6f dump.f2fs: add -I nid to dump inode by scan full disk
ebc3879 android_config: add time headers
c1144bf Check fallthrough in mount.h for Mac
bcb9929 avoid unnecessary function
7d902f4 Fix dependencies on linux/blkzoned.h when using Bionic.
274abbb Remove unnecessary config.h
8c97ab3 libzone: remove duplicate header
adcec10 Support zoned device if libc exists
efc2bc7 mkfs.f2fs: fix typo
3034a41 mkfs.f2fs: split unused parameter
dd8d8e5 f2fs-tools: do not use SG_IO in Android
4f216e6 f2fs-tools: move android_config before defining them
48c5dbb f2fscrypt: adjust config file first
4b55459 android_config: add missing uuid library
Signed-off-by: Nick Hainke <vincent@systemli.org>
This fixes the build of util-linux on powerpc and arc. Both CPU
architectures were not supported here in addition to the missing MIPS
support.
Fixes: 628a410ed1 ("util-linux: update to 2.39")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
8f78aff2cb68 ubus: support multiple call return values
51f4dba67313 ucode: also link libresolv if ns_initparse() is not found
5c7d07773a59 uci: fix ctx.commit() without arguments
5163867269fc Merge pull request #148 from jow-/uci-fix-commit
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Based on Paul Fertser <fercerpav@gmail.com>'s guidance:
Change AUTORELEASE in rules.mk to:
```
AUTORELEASE = $(if $(DUMP),0,$(shell sed -i "s/\$$(AUTORELEASE)/$(call commitcount,1)/" $(CURDIR)/Makefile))
```
then update all affected packages by:
```
for i in $(git grep -l PKG_RELEASE:=.*AUTORELEASE | sed 's^.*/\([^/]*\)/Makefile^\1^';);
do
make package/$i/clean
done
```
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
_LARGEFILE64_SOURCE has to be defined in the source, or CFLAGS can be used
to pass -D_LARGEFILE64_SOURCE to allow to keep using LFS64 definitions.
Fixes error in the form of:
restripe.c: In function 'restore_stripes':
restripe.c:758:43: error: 'off64_t' undeclared (first use in this function); did you mean 'off_t'?
758 | (off64_t)read_offset) {
| ^~~~~~~
| off_t
restripe.c:758:43: note: each undeclared identifier is reported only once for each function it appears in
restripe.c:758:51: error: expected ')' before 'read_offset'
758 | (off64_t)read_offset) {
| ^~~~~~~~~~~
| )
restripe.c:757:36: note: to match this '('
757 | if (lseek64(source, read_offset, 0) !=
| ^
make[3]: *** [Makefile:193: restripe.o] Error 1
Fixes: fff878c5bc ("toolchain/musl: update to 1.2.4")
Signed-off-by: Nick Hainke <vincent@systemli.org>
musl 1.2.4 deprecated legacy "LFS64" ("large file support") interfaces and
autotools failed to check the lseek64 function.
Force enable ac_cv_func_lseek64 to workaround it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
musl 1.2.4 deprecated legacy "LFS64" ("large file support") interfaces and
autotools failed to check the lseek64 function.
Force enable ac_cv_func_lseek64 to workaround it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The resize tool will resize the prompt to match the current terminal
size. This is helpful when connecting to the system using UART to make
the vi or top output match the current terminal size.
This increases the busybox binary size by 136 bytes and the ipkg size by
335 bytes on aarch64.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Commit 9d96b6fb72 ("ath79/mikrotik: disable building NAND images")
disabled building images for MikroTik devices with NAND flash due to a
less than satisfactory method used for updating the kernel on those
devices back then.
To address the problem, add support for updating the kernel on MikroTik
devices with NAND flash using a new tool, Yafut, which enables copying
files from/to Yaffs file systems even if the kernel does not have native
support for the Yaffs file system compiled in. Instead of erasing the
entire NAND partition holding the kernel during every system upgrade
(which is what the previously-used approach employing kernel2minor
involved), Yafut preserves the Yaffs filesystem present on that
partition and only replaces the kernel executable. This allows bad
block information to be preserved across sysupgrade runs and also
enables wear leveling on the NAND partition holding the kernel. Yafut
does not rely on kernel2minor in any way and intends to eventually
supersede the latter for NAND devices.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
I found use for this in my scripts; I noticed that it is already
compiled with util-linux - there just isn't package for it -
let's package it then.
Description:
The rev utility copies the specified files to the standard output,
reversing the order of characters in everyline.
Signed-off-by: Oskari Rauta <oskari.rauta@gmail.com>
This reduces open coding and allows to easily add a knob to enable
it treewide, where chosen packages can still opt-out via "no-lto".
Some packages used LTO, but not the linker plugin. This unifies 'em
all to attempt to produce better code.
Quoting man gcc(1):
"This improves the quality of optimization by exposing more code to the
link-time optimizer."
Also use -flto=auto instead of -flto=jobserver, as it's not guaranteed
that every buildsystem uses +$(MAKE) correctly.
Signed-off-by: Andre Heider <a.heider@gmail.com>
This reduces open coding and allows to easily add a knob to
enable it treewide, where chosen packages can still opt-out via
"no-gc-sections".
Note: libnl, mbedtls and opkg only used the CFLAGS part without the
LDFLAGS counterpart. That doesn't help at all if the goal is to produce
smaller binaries. I consider that an accident, and this fixes it.
Note: there are also packages using only the LDFLAGS part. I didn't
touch those, as gc might have been disabled via CFLAGS intentionally.
Signed-off-by: Andre Heider <a.heider@gmail.com>
This splits the code in 4 files:
- uencrypt.h
- uencrypt.c - main program
- uencrypt-openssl.c - OpenSSL/wolfSSL implementation
- uencrypt-mbedtls - mbedTLS implementation
Other changes, accounting for ~400 bytes increase in ipk size:
- more error condition checking and reporting,
- hide key and iv command line arguments
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This commit includes some additional changes:
- better handling of iv and keys in openssl/wolfssl variants
- fix compiler warnings and whitespace
- build all 3 variants as separate packages
- adjust the new package name in targets' DEVICE_PACKAGES
- remove PKG_FLAGS:=nonshared
[Beeline SmartBox Flash - OK]
Tested-by: Mikhail Zhilkin <csharper2005@gmail.com>
[after test: replaced a hardcoded IV size of 16 by cipher_info->iv_size]
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Changelog:
039a994 Bump version to v1.7.0
3f29d6d pylibfdt: add size_hint parameter for get_path
2022bb1 checks: Update #{size,address}-cells check for 'dma-ranges'
abbd523 pylibfdt: Work-around SWIG limitations with flexible arrays
a41509b libfdt: Replace deprecated 0-length arrays with proper flexible arrays
2cd89f8 dtc: Warning rather than error on possible truncation of cell values
55778a0 libfdt: tests: add get_next_tag_invalid_prop_len
7359034 libfdt: prevent integer overflow in fdt_next_tag
035fb90 libfdt: add fdt_get_property_by_offset_w helper
98a0700 Makefile: fix infinite recursion by dropping non-existent `%.output`
a036cc7 Makefile: limit make re-execution to avoid infinite spin
c6e9210 libdtc: remove duplicate judgments
e37c256 Don't generate erroneous fixups from reference to path
5045465 libfdt: Don't mask fdt_get_name() returned error
e64a204 manual.txt: Follow README.md and remove Jon
f508c83 Update README in MANIFEST.in and setup.py to README.md
c2ccf8a Add description of Signed-off-by lines
90b9d9d Split out information for contributors to CONTRIBUTING.md
0ee1d47 Remove Jon Loeliger from maintainers list
b33a73c Convert README to README.md
7ad6073 Allow static building with meson
fd9b8c9 Allow static building with make
fda71da libfdt: Handle failed get_name() on BEGIN_NODE
c7c7f17 Fix test script to run also on dash shell
01f23ff Add missing relref_merge test to meson test list
ed31080 pylibfdt: add FdtRo.get_path()
c001fc0 pylibfdt: fix swig build in install
26c54f8 tests: add test cases for label-relative path references
ec7986e dtc: introduce label relative path references
651410e util: introduce xstrndup helper
4048aed setup.py: fix out of tree build
ff5afb9 Handle integer overflow in check_property_phandle_args()
ca72944 README: Explain how to add a new API function
c0c2e11 Fix a UB when fdt_get_string return null
cd5f69c tests: setprop_inplace: use xstrdup instead of unchecked strdup
a04f690 pylibfdt: add Property.as_*int*_array()
8310271 pylibfdt: add Property.as_stringlist()
d152126 Fix Python crash on getprop deallocation
17739b7 Support 'r' format for printing raw bytes with fdtget
45f3d1a libfdt: overlay: make overlay_get_target() public
c19a4ba libfdt: fix an incorrect integer promotion
1cc41b1 pylibfdt: Add packaging metadata
db72398 README: Update pylibfdt install instructions
383e148 pylibfdt: fix with Python 3.10
23b56cb pylibfdt: Move setup.py to the top level
69a7607 pylibfdt: Split setup.py author name and email
0b106a7 pylibfdt: Use setuptools_scm for the version
c691776 pylibfdt: Use setuptools instead of distutils
5216f3f libfdt: Add static lib to meson build
4eda259 CI: Cirrus: bump used FreeBSD from 12.1 to 13.0
0a3a9d3 checks: Add an interrupt-map check
8fd2474 checks: Ensure '#interrupt-cells' only exists in interrupt providers
d8d1a9a checks: Drop interrupt provider '#address-cells' check
52a16fd checks: Make interrupt_provider check dependent on interrupts_extended_is_cell
37fd700 treesource: Maintain phandle label/path on output
e33ce1d flattree: Use '\n', not ';' to separate asm pseudo-ops
d24cc18 asm: Use assembler macros instead of cpp macros
ff3a30c asm: Use .asciz and .ascii instead of .string
5eb5927 fdtdump: fix -Werror=int-to-pointer-cast
0869f82 libfdt: Add ALIGNMENT error string
69595a1 checks: Fix bus-range check
72d09e2 Makefile: add -Wsign-compare to warning options
b587787 checks: Fix signedness comparisons warnings
69bed6c dtc: Wrap phandle validity check
9102211 fdtget: Fix signedness comparisons warnings
d966f08 tests: Fix signedness comparisons warnings
ecfb438 dtc: Fix signedness comparisons warnings: pointer diff
5bec74a dtc: Fix signedness comparisons warnings: reservednum
24e7f51 fdtdump: Fix signedness comparisons warnings
Remove upstreamed:
- 0001-Support-r-format-for-printing-raw-bytes-with-fdtget.patch
Signed-off-by: Nick Hainke <vincent@systemli.org>
* Fix incorrect error message in case input file opening fails
* Don't close files in case the pointers are invalid
Signed-off-by: David Bauer <mail@david-bauer.net>
Just as lua or the various languages from the package feed.
libucode is the exception, so move it to the libs menu instead.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Instead of accessing /dev/urandom use the getrandom syscall. This way we
do not have to keep the file open all the time.
This also fixes a compile error with glibc:
--------
px5g-mbedtls.c: In function '_urandom':
px5g-mbedtls.c:48:9: error: ignoring return value of 'read' declared with attribute 'warn_unused_result' [-Werror=unused-result]
48 | read(urandom_fd, out, len);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
--------
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To bring in isatty() support.
Includes new commits:
be30472bfdbb fs: add `isatty()` function
0a58d510529e nl80211: add support for NL80211_ATTR_MPATH_INFO
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[ remove additional merge commit ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The bpf plugin provides functionality for loading and interacting with
eBPF modules.
It allows loading full modules and pinned maps/programs and supports
interacting with maps and attaching programs as tc classifiers.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
34cfbb922c96 README.md: various spelling and documentation fixes
ff32355ea645 build: make rtnl/nl80211 depend on linux instead of !APPLE
c0e413c21f7b include: add uc_fn_thisval()
1e4d20932646 Merge pull request #134 from nbd168/thisval
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Update busybox to version 1.36.0
* refresh patches (remove the backported upstream fix)
* refresh config
Config refresh:
Refresh commands, run after busybox is first built once:
cd package/utils/busybox/config/
../convert_menuconfig.pl ../../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.36.0
cd ..
./convert_defaults.pl ../../../build_dir/target-arm_cortex-a15+neon-vfpv4_musl_eabi/busybox-default/busybox-1.36.0/.config > Config-defaults.in
Manual edits needed after config refresh:
* Config-defaults.in: OpenWrt config symbol IPV6 logic applied to
BUSYBOX_DEFAULT_FEATURE_IPV6
* Config-defaults.in: OpenWrt config TARGET_bcm53xx logic applied to
BUSYBOX_DEFAULT_TRUNCATE (commit 547f1ec)
* Config-defaults.in: OpenWrt logic applied to
BUSYBOX_DEFAULT_LOGIN_SESSION_AS_CHILD (commit dc92917)
* Config-defaults.in: correct the default ports that get reset
BUSYBOX_DEFAULT_FEATURE_HTTPD_PORT_DEFAULT 80
BUSYBOX_DEFAULT_FEATURE_TELNETD_PORT_DEFAULT 23
* config/editors/Config.in: Add USE_GLIBC dependency to
BUSYBOX_CONFIG_FEATURE_VI_REGEX_SEARCH (commit f141090)
* config/shell/Config.in: change at "Options common to all shells" the conditional symbol
SHELL_ASH --> BUSYBOX_CONFIG_SHELL_ASH
(discussion in http://lists.openwrt.org/pipermail/openwrt-devel/2021-January/033140.html
Apparently our script does not see the hidden option while
prepending config options with "BUSYBOX_CONFIG_" which leads to a
missed dependency when the options are later evaluated.)
* Edit a few Config.in files by adding quotes to sourced items in
config/Config.in, config/networking/Config.in and config/util-linux/Config.in (commit 1da014f)
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
The ABI of the wolfssl library changed a bit between version 5.5.3 and
5.5.4. This release update will trigger a rebuild of all packages which
are using wolfssl to make sure they are adapted to the new ABI.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The libraries libpthread, libdl, libutil, libanl have been integrated
into the libc library in version 2.34. it is not needed to explicitly
link them any more.
Most of the functions have been moved from the librt.so into libc.so
some time ago already.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes CVE-2022-1304:
An out-of-bounds read/write vulnerability was found in e2fsprogs 1.46.5.
This issue leads to a segmentation fault and possibly arbitrary code
execution via a specially crafted filesystem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This backports a commit which fixes a use after free bug in awk.
CVE-2022-30065 description:
A use-after-free in Busybox 1.35-x's awk applet leads to denial of
service and possibly code execution when processing a crafted awk
pattern in the copyvar function.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
