The upstream submission for this mandates the node to be named wifi
instead of wmac. Change all ath79 entries to match the new names and
remove the compatibility patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19328
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ath9k ahb patch was updated to match the latest upstream version,
however the openwrt DT files still use the older names.
Add those as extra entries in order to remain compatible until DT files
are fixed.
Fixes: 88f4c32060 ("mac80211: update to version 6.14.11")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
QCN6122 wifi in fw-memory-mode 1 has a slightly larger caldb size than
currently defined in the ath11k driver. When coldboot calibration was
disabled, the fw mem mode was changed from 2 (256MB mem profile) to 1
(512MB mem profile), which is the correct setting for devices in scope.
However, in fw mem mode, the caldb size is 0x500000 instead of the max
0x480000 defined in the driver, causing QCN6122 wifi failing to boot:
ath11k b00a040.wifi1: qmi mem size is low to load caldata
ath11k b00a040.wifi1: failed to assign qmi target memory: -22
As such, change the max caldb memory size accordingly.
This macro is used by the driver only as a max size limit to validate
the requested caldb size returned by QMI. Different ath11k wifi chips
have different caldb sizes (for ex. the size for IPQ5018 is 0x200000).
Fixes: cf715a2305 ("wifi: ath11k: disable coldboot calibration for ipq5018")
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19118
Signed-off-by: Robert Marko <robimarko@gmail.com>
Coldboot calibration does not work causes the firmware to crash during
wifi startup. So let's disable coldboot calibration until a solution is
found.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/19083
Signed-off-by: Robert Marko <robimarko@gmail.com>
The original OF code effectively does a reset at ahb.c but then again in
hw.c. For AR9330, it's already done in the driver and with the others,
there are patches in here that do the same. hw.c looks like the proper
place to handle this.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19031
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fixes ath9k on ar934x platforms.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19031
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream seems to be using led-sources instead of custom properties.
Code mostly taken from mt76.
Changed all(few) users of qca,led_pin to use the new format.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18805
Signed-off-by: Robert Marko <robimarko@gmail.com>
It's the proper function to handle this stuff in.
The original patch abused the fact that the ath9k driver in init called
ath9k_init_platform to populate all the needed configuration. This is
the wrong place to do so and it also goes away in 6.13.
Move 553-ath9k_of_gpio_mask.patch contents to ath9k_of_init where they
belong.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/18764
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix following warnings by including the corresponding headers:
backports-6.12.6/drivers/net/wireless/ath/ath9k/hsr.c:50:6: error: no previous prototype for 'ath9k_hsr_init' [-Werror=missing-prototypes]
50 | void ath9k_hsr_init(struct ath_hw *ah)
| ^~~~~~~~~~~~~~
backports-6.12.6/drivers/net/wireless/ath/ath9k/hsr.c:165:5: error: no previous prototype for 'ath9k_hsr_disable' [-Werror=missing-prototypes]
165 | int ath9k_hsr_disable(struct ath_hw *ah)
| ^~~~~~~~~~~~~~~~~
backports-6.12.6/drivers/net/wireless/ath/ath9k/hsr.c:177:5: error: no previous prototype for 'ath9k_hsr_enable' [-Werror=missing-prototypes]
177 | int ath9k_hsr_enable(struct ath_hw *ah, int bw, int fq)
| ^~~~~~~~~~~~~~~~
backports-6.12.6/drivers/net/wireless/ath/ath9k/hsr.c:234:5: error: no previous prototype for 'ath9k_hsr_status' [-Werror=missing-prototypes]
234 | int ath9k_hsr_status(struct ath_hw *ah)
| ^~~~~~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18637
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix mt76 build error on 6.12 kernel:
In file included from /workspaces/openwrt/build_dir/target-x86_64_musl/linux-x86_64/mt76-2025.04.11~be28ef77/mt76x0/eeprom.c:13:
/workspaces/openwrt/staging_dir/target-x86_64_musl/usr/include/mac80211-backport/asm/unaligned.h:3:15: fatal error: asm/unaligned.h: No such file or directory
3 | #include_next <asm/unaligned.h>
| ^~~~~~~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18637
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Move rt2x00lib_read_eeprom() function prototype from rt2800lib.h to
rt2x00.h and make rt6352_enable_pa_pin() static to fix the missing
prototypes warnings:
/workspaces/openwrt/build_dir/target-x86_64_musl/linux-x86_64/mac80211-regular/backports-6.12.6/drivers/net/wireless/ralink/rt2x00/rt2x00eeprom.c:213:5: error: no previous prototype for 'rt2x00lib_read_eeprom' [-Werror=missing-prototypes]
213 | int rt2x00lib_read_eeprom(struct rt2x00_dev *rt2x00dev)
| ^~~~~~~~~~~~~~~~~~~~~
/workspaces/openwrt/build_dir/target-x86_64_musl/linux-x86_64/mac80211-regular/backports-6.12.6/drivers/net/wireless/ralink/rt2x00/rt2800lib.c:308:6: error: no previous prototype for 'rt6352_enable_pa_pin' [-Werror=missing-prototypes]
308 | void rt6352_enable_pa_pin(struct rt2x00_dev *rt2x00dev, int enable)
| ^~~~~~~~~~~~~~~~~~~~
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/18637
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since the irq gets copied to sc, it's a really bad idea to use devm,
especially when probe fails.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Fixes: 4e18d22 ("mac80211: ath9k: simplify probe with devm")
Link: https://github.com/openwrt/openwrt/pull/18570
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add backport patch that fixes ath12k regdomain parsing failure in
6GHz band triggered by the latest regdb/board-2.bin update.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18512
Signed-off-by: Robert Marko <robimarko@gmail.com>
Previous commits missed some refreshing
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18512
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add patches to enable QCN9274 radios that support both 5GHz and 6GHz
bands.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In board-2.bin available at linux-firmare regdb is stored with
board-id=255. This change is needed to properly use it.
Signed-off-by: Mantas Pucka <mantas@8devices.com>
Link: https://github.com/openwrt/openwrt/pull/18459
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
ath9k uses a deprecated GPIO API that assumes a starting base of 0. This
is no longer the case and so must be fixed.
Upstream pending patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is only used by mach files, which are no longer used in OpenWrt.
Allows removing a custon ath9k_platform.h file.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
These only work with and are useful with mach files. Now that those are
gone, this can go too.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
Simplify patch with gpiochip_add_data, struct reduction, new GPIO API,
and header cleanup.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17445
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport two commits to resolve issues with ath1kk causing it to fail
driver registration on iommuless systems with DRAM outside of 32bit
addressing such as a 4GiB imx8mm:
commit 1bcd20981834 ("wifi: ath11k: Fix DMA buffer allocation
to resolve SWIOTLB issues")
commit eeadc6baf8b3 ("wifi: ath11k: Use dma_alloc_noncoherent
for rx_tid buffer allocation")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/17751
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix compilation error for old stable version caused by
genlmsg_multicast_allns backport fix pushed middle version.
Version 5.15 version 0-169, 6.1 version 0-115, 6.6 version 0-58 have the
old genlmsg_multicast_allns version with flags variable.
Compiling backport project with these version result in a compilation
error. To handle this, introduce a backport function for the affected
kernel version.
Link: https://github.com/openwrt/openwrt/pull/18373
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This downstream patch fixes a bug which could flood the logs with the
following message and would eventually lead to a crash.
ath11k c000000.wifi: failed to send HAL_REO_CMD_UPDATE_RX_QUEUE cmd, tid 0 (-105)
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add QCN6122 platform support.
QCN6122 is a PCIe based solution that is attached to and enumerated
by the WPSS (Wireless Processor SubSystem) Q6 processor.
Though it is a PCIe device, since it is not attached to APSS processor
(Application Processor SubSystem), APSS will be unaware of such a decice
and hence it is registered to the APSS processor as a platform device(AHB).
Because of this hybrid nature, it is called as a hybrid bus device.
As such, QCN6122 is a hybrid bus type device and follows the same codepath
as for WCN6750.
This is a reversed engineered and heavily simplified version of below
downstream patch:
https://git.codelinaro.org/clo/qsdk/oss/system/feeds/wlan-open/-/ \
blob/NHSS.QSDK.12.4.5.r2/mac80211/patches/232-ath11k-qcn6122-support.patch
Co-developed-by: George Moussalem <george.moussalem@outlook.com>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
IPQ5018 uses different BDF and caldb addresses for vairous boards,
so let's support reading these addresses from the device tree.
Signed-off-by: Ziyang Huang <hzyitc@outlook.com>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/17182
Signed-off-by: Robert Marko <robimarko@gmail.com>
Update handling of macro __assign_str() to also support the one-argument
variant when building against kernel 6.10 or later. This is needed for
building the next LTS kernel 6.12.
Fixes: 384d079fd8 ("mac80211: update to version 6.11")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/17456
Signed-off-by: Robert Marko <robimarko@gmail.com>
Change the double-include guard to avoid conflict with the linux kernel header
Reported-by: Tony Ambardar <itugrok@yahoo.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Simplify patch with gpiochip_add_data, struct reduction, new GPIO API,
and header cleanup.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16635
Signed-off-by: Robert Marko <robimarko@gmail.com>
These only work with and are useful with mach files. Now that those are
gone, this can go too.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16635
Signed-off-by: Robert Marko <robimarko@gmail.com>
This goes away in kernel 6.12 upstream.
Get ahead of the curve by fixing all the local patches as well.
Get rid of CONFIG_OF. It's needed now.
Refreshed all patches.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16635
Signed-off-by: Robert Marko <robimarko@gmail.com>
